COChristopher Oshman

Christopher Oshman

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Christopher Oshman has a total of 92 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Impact of Substrate Vibrations on Self-Alignment Accuracy in BGA/Flip-Chip Assembly

    by Ming Kong, Yung-Cheng Lee, Christopher Oshman

    Solder self-alignment is a crucial manufacturing technology for the cost-effective assembly of optoelectronic devices that require precise positioning. However, concerns remain about the quality of self-alignment, especially due to dynamic factors like mechanical vibrations from conveyor belts during the manufacturing process. Additionally, there has been a lack of comprehensive experimental studies and models to fully address these issues. In this paper, the dynamic behavior of a BGA flip-chip assembly reflowed under forced environmental periodical vibration was investigated. Due to low dissipative force of the molten solder joint, resonant oscillations between chip and substrate were observed at around 12 Hz driving frequency. The maximum chip’s oscillation amplitude can reach more than 100 μm for only several microns’ driven amplitude on the substrate. This resonant motion can be “frozen in” during the solidification of the joint, resulting in large post-assembly misalignments. In order to reduce the adverse influence of environmental vibration on self-alignment accuracy, several feasible methods were proposed, including varying solder surface tension coefficient, adjusting solder joint aspect ratio, adjusting chip mass or the number of joint interconnections, in order to shift the resonant frequency of the to-be-assembled device to a range that is different from the frequency of environmental vibrations.

  • Prototype latent heat storage system with aluminum-silicon as a phase change material and a Stirling engine for electricity generation

    by Jonathan E. Rea, Christopher J. Oshman, Abhishek Singh, Jeff Alleman, Greg Buchholz, Philip A. Parilla, Jesse M. Adamczyk, Helena-Nikolai Fujishin, Brenden R. Ortiz, Tara Braden, et al.


  • Techno-economic analysis of a small scale solar power tower at varied locations

    by Jonathan E. Rea, Greg C. Glatzmaier, Christopher Oshman, Philip A. Parilla, Nathan P. Siegel, David S. Ginley, Eric S. Toberer

    Location selection is an important factor for the effectiveness and cost of a solar electricity generation system. Latitude and weather impact efficiency and availability, and local labor rates have a further influence on cost. To explore the impact of these effects, we performed techno-economic analysis of a small-scale solar power tower concept in six different locations in the United States, Australia, and India. The specific configuration we considered has a nominal power rating of 100 kWe and 5 hours of thermal energy storage. Further, we considered two deployment strategies: a single stand-alone 100 kWe tower, and a 20 MWe cluster of many towers. For each scenario, we used a probabilistic analysis method to evaluate levelized cost of electricity. We found that this configuration has potential for cost-competitive electricity generation and the ability to improve grid flexibility for integration of intermittent renewables. In addition, solar resource, latitude, and local labor rates all have an impact on the levelized cost of electricity of the system.


  • Demonstration of a thermosyphon thermal valve for controlled extraction of stored solar thermal energy

    by Christopher Oshman, Jon Rea, Corey Hardin, Abhishek Singh, Jeff Alleman, Michele Olsen, Greg Glatzmaier, Phillip Parilla, Nathan Siegel, David Ginley, et al.

    For concentrated solar power (CSP) to be an effective replacement for power generation by fossil fuels, the thermal energy must be stored and then released for when demand exceeds production, such as during off-sun hours. Until now, there has been limited methods to reliably and efficiently release and control the extraction of thermal energy from a material containing stored sensible or latent heat. Due to their isothermal property, phase change materials (PCMs) storing latent heat are an ideal choice for storage, though it has proven challenging to reliably extract and utilize that heat. To solve this problem, the geometry of a thermosyphon was rearranged to create a thermal valve that is able to turn the flow of thermal energy from a PCM “on” and “off”. A stainless steel thermal valve using sodium as the working fluid was designed, fabricated, assessed, and found to effectively and selectively extract heat from a 577°C molten aluminum PCM. It is expected that thermal valves will significantly contribute to more widespread implementation of CSP as a stored energy source from distributed generation to utility-scale power production.


  • Experimental demonstration of a latent heat storage system for dispatchable electricity

    by Jonathan E. Rea, Christopher Oshman, Corey L. Hardin, Abhishek Singh, Jeff Alleman, Greg Glatzmaier, Philip A. Parilla, Michele L. Olsen, Jeff Sharp, Nathan P. Siegel, et al.

    Modern electric grids that use intermittent renewables require energy storage to maintain reliability. Many potential solutions exist, but latent heat thermal energy storage shows particularly high potential for low cost grid scale energy storage. In this paper, we present the design and initial experimental results for a lab-scale prototype of a novel latent heat thermal storage system. This version of our prototype used 50 kg of aluminum-silicon alloy as a phase change material, and a novel valved thermosyphon concept to control heat flow from a thermal storage tank to thermoelectric generators for dispatchable electricity production. Our results validate the system: the thermal storage system was able to receive heat input, evenly distribute heat to and from the phase change material with small temperature gradients, and controllably dispatch heat to a heat engine for electricity generation on demand. With the basic principle of this technology demonstrated, our next step will be to evaluate and improve system efficiency.


  • Experimental demonstration of a dispatchable latent heat storage system with aluminum-silicon as a phase change material

    by Jonathan E. Rea, Christopher J. Oshman, Abhishek Singh, Jeff Alleman, Philip A. Parilla, Corey L. Hardin, Michele L. Olsen, Nathan P. Siegel, David S. Ginley, Eric S. Toberer


  • Reliability and heat transfer performance of a miniature high-temperature thermosyphon-based thermal valve

    by Christopher Oshman, Jonathan Rea, Corey Hardin, Michele L. Olsen, Jeff Alleman, Greg Glatzmaier, Nathan Siegel, Philip Parilla, David Ginley, Eric S. Toberer


  • Performance modeling and techno-economic analysis of a modular concentrated solar power tower with latent heat storage

    by Jonathan E. Rea, Christopher J. Oshman, Michele L. Olsen, Corey L. Hardin, Greg C. Glatzmaier, Nathan P. Siegel, Philip A. Parilla, David S. Ginley, Eric S. Toberer


  • Design of a thermosyphon-based thermal valve for controlled high-temperature heat extraction

    by Christopher Oshman, Corey Hardin, Jonathan Rea, Michele L. Olsen, Nathan Siegel, Greg Glatzmaier, Phil Parilla, David Ginley, Eric S. Toberer


  • Solar thermoelectricity via advanced latent heat storage: A cost-effective small-scale CSP application

    by G. C. Glatzmaier, J. Rea, M. L. Olsen, C. Oshman, C. Hardin, J. Alleman, J. Sharp, R. Weigand, D. Campo, G. Hoeschele, et al.

    We are developing a novel concentrating solar electricity-generating technology that is both modular and dispatchable. Solar ThermoElectricity via Advanced Latent heat Storage (STEALS) uses concentrated solar flux to generate high-temperature thermal energy, which directly converts to electricity via thermoelectric generators (TEGs), stored within a phase-change material (PCM) for electricity generation at a later time, or both allowing for simultaneous charging of the PCM and electricity generation. STEALS has inherent features that drive its cost-competitive scale to be much smaller than current commercial concentrating solar power (CSP) plants. Most obvious is modularity of the solid-state TEG, which favors smaller scales in the kilowatt range as compared to CSP steam turbines, which are minimally 50 MWe for commercial power plants. Here, we present techno-economic and market analyses that show STEALS can be a cost-effective electricity-generating technology with particular appeal to small-scale microgrid applications. We evaluated levelized cost of energy (LCOE) for STEALS and for a comparable photovoltaic (PV) system with battery storage. For STEALS, we estimated capital costs and the LCOE as functions of the type of PCM including the use of recycled aluminum alloys, and evaluated the cost tradeoffs between plasma spray coatings and solution-based boron coatings that are applied to the wetted surfaces of the PCM subsystem. We developed a probabilistic cost model that accounts for uncertainties in the cost and performance inputs to the LCOE estimation. Our probabilistic model estimated LCOE for a 100-kWe STEALS system that had 5 hours of thermal storage and 8–10 hours of total daily power generation. For these cases, the solar multiple for the heliostat field varied between 1.12 and 1.5. We identified microgrids as a likely market for the STEALS system. We characterized microgrid markets in terms of nominal power, dispatchability, geographic location, and customer type, and specified additional features for STEALS that are needed to meet the needs of this growing power market.