Katarzyna Mulewska
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Katarzyna Mulewska has a total of 80 co-authors. Here are the top co-authors by number of shared publications:
- Lukasz Kurpaska
National Centre for Nuclear Research
5 shared publications - Magdalena Wilczopolska
NOMATEN Centre of Excellence, National Centre for Nuclear Research
5 shared publications - Anna Kosińska
NOMATEN Centre of Excellence, National Centre for Nuclear Research, A. Soltana 7, 05-400 Otwock, Poland
4 shared publications - Damian Kalita
Polish Academy of Sciences
4 shared publications - Józef Rzempołuch
Materials Research Laboratory, National Centre for Nuclear Research, A. Soltana 7, 05-400 Otwock, Poland
4 shared publications - Katarzyna Ciporska
Materials Research Laboratory, National Centre for Nuclear Research, A. Soltana 7, 05-400 Otwock, Poland
4 shared publications
Latest Publications
- Open Access
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Irradiation Temperature Governs the Transition in Plastic Initiation From Nucleation to Defect-controlled Behaviour in Fe-9Cr-NiSiP
Ion irradiation modifies the nanoscale initiation of plasticity in ferritic Fe-Cr alloys through the formation and evolution of irradiation-induced defects. Here, the deformation behaviour of a Fe-9Cr-NiSiP model alloy irradiated to 5 dpa at room temperature and 300°C is examined. Nanoindentation reveals systematic changes in pop-in behaviour, indicating a transition from nucleation-controlled plastic initiation in the pristine material to defect-controlled deformation after irradiation. Room-temperature irradiation produces a high density of fine defect structures that promote heterogeneous dislocation nucleation while restricting dislocation motion. In contrast, irradiation at 300°C leads to defect coarsening and solute segregation of Cr, Ni, Si and P, forming more stable defect complexes that delay plastic initiation. Correlative microscopy reveals distinct subsurface deformation morphologies consistent with the mechanical response. These results show that irradiation temperature controls defect evolution, which in turn governs the nanoscale onset of plasticity in Fe-Cr alloys.
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessIrradiation Temperature Governs the Transition in Plastic Initiation From Nucleation to Defect-controlled Behaviour in Fe-9Cr-NiSiP
Ion irradiation modifies the nanoscale initiation of plasticity in ferritic Fe-Cr alloys through the formation and evolution of irradiation-induced defects. Here, the deformation behaviour of a Fe-9Cr-NiSiP model alloy irradiated to 5 dpa at room temperature and 300°C is examined. Nanoindentation reveals systematic changes in pop-in behaviour, indicating a transition from nucleation-controlled plastic initiation in the pristine material to defect-controlled deformation after irradiation. Room-temperature irradiation produces a high density of fine defect structures that promote heterogeneous dislocation nucleation while restricting dislocation motion. In contrast, irradiation at 300°C leads to defect coarsening and solute segregation of Cr, Ni, Si and P, forming more stable defect complexes that delay plastic initiation. Correlative microscopy reveals distinct subsurface deformation morphologies consistent with the mechanical response. These results show that irradiation temperature controls defect evolution, which in turn governs the nanoscale onset of plasticity in Fe-Cr alloys.
- Open Access
- 25 October 2025
- Published by Elsevier in Acta Materialia
- Vol. 302
Formation of coherent nanocomposite structure in nickel-aluminum alloys synthesized far from equilibrium
- 25 October 2025
- Published by Elsevier in Acta Materialia
- Vol. 302
Open AccessFormation of coherent nanocomposite structure in nickel-aluminum alloys synthesized far from equilibrium
- Open Access
- 29 August 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 617
Mechanical properties, 475°C embrittlement and irradiation resistance of FeCrAl-Y2O3 ODS alloy with Ti and V alloying additions
- 29 August 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 617
Open AccessMechanical properties, 475°C embrittlement and irradiation resistance of FeCrAl-Y2O3 ODS alloy with Ti and V alloying additions
- Open Access
- 14 August 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 616
Microstructural evolution and mechanical response of ion-irradiated Fe-9Cr alloys: Insights from nanoindentation
- 14 August 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 616
Open AccessMicrostructural evolution and mechanical response of ion-irradiated Fe-9Cr alloys: Insights from nanoindentation
- Open Access
- 6 August 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 616
Characterization of He+ implanted W-Zr-B thin films deposited by HiPIMS on additively manufactured Inconel 617 as a candidate system for nuclear components
- 6 August 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 616
Open AccessCharacterization of He+ implanted W-Zr-B thin films deposited by HiPIMS on additively manufactured Inconel 617 as a candidate system for nuclear components
- Open Access
- 17 July 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 37, 5448-5464
High-temperature radiation resistance of NiCoFe medium-entropy alloy enabled by stable nanostructures and defect evolution mechanisms
- 17 July 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 37, 5448-5464
Open AccessHigh-temperature radiation resistance of NiCoFe medium-entropy alloy enabled by stable nanostructures and defect evolution mechanisms
- 16 June 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 615
Effects of Fe2+ ion-irradiation on additively manufactured Inconel 617 alloy
- 16 June 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 615
Effects of Fe2+ ion-irradiation on additively manufactured Inconel 617 alloy
- 1 March 2025
- Published by Index Copernicus in Journal of Achievements in Materials and Manufacturing Engineering
Microstructure characterisation and mechanical behaviour of spark plasma sintered FeCrAl-Y2O3-Ti ODS alloys for nuclear applications
The paper examines mechanically alloyed and spark plasma sintered FeCrAl-based ODS alloys with different amounts of titanium additions in terms of their potential application in gas-cooled fast nuclear reactors (GFRs). The research aims to elucidate how Ti addition influences the alloys’ microstructural properties and focuses on the microstructural stability characterisation and mechanical properties evaluation of the FeCrAl-ODS alloys at high temperatures up to 800C.In the given study, two compositions of FeCrAl ODS alloys with fixed 9% chromium, 5% aluminium, 0.3% yttrium oxide, and different titanium additions 0.5% and 1%, were mechanically alloyed (MA). The powders were then consolidated via spark plasma sintering (SPS) technique at 1050C, 40 MPa for 10 minutes and finally annealed at 1020C for 30 minutes. The resulting bulk materials were characterised for their microstructure and chemical composition using SEM-EDS and EBSD. Density measurements were conducted using Archimedes’ principle, while mechanical properties were evaluated through Vickers microhardness tests and tensile testing of the miniaturised samples in the range from RT to 800C.The successfully synthesised FeCrAl-Y2O3-Ti ODS alloys achieved a density of approximately 96% and a fine α-ferrite microstructure with most grains under 1 μm. Microstructural analysis revealed α-ferrite grains and the presence of nano- and micro-scale oxide and carbide precipitates. These are expected to stabilise the microstructure and enhance high strength at creep conditions and radiation resistance. Due to mechanical alloying, the crystallite size significantly decreased to about 50 nm, indicating adequate processing conditions. Additionally, the addition of titanium was found to improve the formation of complex oxides and carbides. Moreover, samples with a higher Ti content showed a higher ultimate tensile strength and yield strength at temperatures up to 500C than those with a lower Ti content. Therefore, it seems that Ti positively impacts the strength of the FeCrAl-Y2O3-Ti ODS alloys, and it is entirely consistent with the hardness results that also reveal higher hardness of the sample with higher Ti content.In FeCrAl-Y2O3-Ti ODS alloys, the oxide particles in the matrix should also significantly reduce the effect of ageing embrittlement at elevated temperatures and improve the stability of the microstructure by reducing grain growth under high-temperature operating conditions, thereby positively affecting the strength of the alloys. The results confirmed the homogeneous distribution of complex nanoscale oxide particles and thus improved mechanical properties. Notably, yield strength and tensile strength decrease with increasing test temperature, which was expected, and for samples above 500C and up to 800C, yield strength and tensile strength are almost the same (within the limits of measurement error). Plastic deformation at fracture is similar in both samples (about 10%) up to 500C. Above 600C, plastic deformation generally increases with increasing test temperature, up to about 50% for samples with lower Ti content at 750C. Although both samples show similar strength in the temperature range from 500C to 800C, the higher Ti content appears to reduce ductility.The main research primarily involved the development of new samples of FeCrAl-based materials with yttrium and titanium oxide additives to assess the feasibility of the designated alloys and their processing for further use in Generation IV reactor technologies. The results suggest that the application of the oxide dispersion enhancement effect can significantly increase the strength of FeCrAl alloys, thus qualifying them as materials potentially suitable for the manufacturing of components and subassemblies used under extreme operating conditions in high-temperature or gas-cooled fast nuclear reactors, including, for example, fuel claddings and hot ducts elements.Oxide dispersion strengthened (ODS) alloys, especially those based on FeCrAl, are recognised for their superior high-temperature strength and irradiation resistance, making them promising candidates for structural components in Generation IV nuclear reactors. Despite their potential, detailed experimental data on their mechanical behaviour at elevated temperatures remain limited, particularly for alloys processed by mechanical alloying and spark plasma sintering (SPS). The study provides new insights into the microstructural characteristics and high-temperature mechanical performance (up to 800 C) of miniaturised FeCrAl–Y2O3–Ti ODS alloy specimens. The originality lies in the specific combination of alloy composition, processing route, and advanced testing methodology, enabling the initial verification of the material’s behaviour under its intended operating conditions. The results contribute to a deeper understanding of how such materials perform in environments relevant to advanced nuclear systems, thus supporting the future application of ODS alloy components.
- 1 March 2025
- Published by Index Copernicus in Journal of Achievements in Materials and Manufacturing Engineering
Microstructure characterisation and mechanical behaviour of spark plasma sintered FeCrAl-Y2O3-Ti ODS alloys for nuclear applications
The paper examines mechanically alloyed and spark plasma sintered FeCrAl-based ODS alloys with different amounts of titanium additions in terms of their potential application in gas-cooled fast nuclear reactors (GFRs). The research aims to elucidate how Ti addition influences the alloys’ microstructural properties and focuses on the microstructural stability characterisation and mechanical properties evaluation of the FeCrAl-ODS alloys at high temperatures up to 800C.In the given study, two compositions of FeCrAl ODS alloys with fixed 9% chromium, 5% aluminium, 0.3% yttrium oxide, and different titanium additions 0.5% and 1%, were mechanically alloyed (MA). The powders were then consolidated via spark plasma sintering (SPS) technique at 1050C, 40 MPa for 10 minutes and finally annealed at 1020C for 30 minutes. The resulting bulk materials were characterised for their microstructure and chemical composition using SEM-EDS and EBSD. Density measurements were conducted using Archimedes’ principle, while mechanical properties were evaluated through Vickers microhardness tests and tensile testing of the miniaturised samples in the range from RT to 800C.The successfully synthesised FeCrAl-Y2O3-Ti ODS alloys achieved a density of approximately 96% and a fine α-ferrite microstructure with most grains under 1 μm. Microstructural analysis revealed α-ferrite grains and the presence of nano- and micro-scale oxide and carbide precipitates. These are expected to stabilise the microstructure and enhance high strength at creep conditions and radiation resistance. Due to mechanical alloying, the crystallite size significantly decreased to about 50 nm, indicating adequate processing conditions. Additionally, the addition of titanium was found to improve the formation of complex oxides and carbides. Moreover, samples with a higher Ti content showed a higher ultimate tensile strength and yield strength at temperatures up to 500C than those with a lower Ti content. Therefore, it seems that Ti positively impacts the strength of the FeCrAl-Y2O3-Ti ODS alloys, and it is entirely consistent with the hardness results that also reveal higher hardness of the sample with higher Ti content.In FeCrAl-Y2O3-Ti ODS alloys, the oxide particles in the matrix should also significantly reduce the effect of ageing embrittlement at elevated temperatures and improve the stability of the microstructure by reducing grain growth under high-temperature operating conditions, thereby positively affecting the strength of the alloys. The results confirmed the homogeneous distribution of complex nanoscale oxide particles and thus improved mechanical properties. Notably, yield strength and tensile strength decrease with increasing test temperature, which was expected, and for samples above 500C and up to 800C, yield strength and tensile strength are almost the same (within the limits of measurement error). Plastic deformation at fracture is similar in both samples (about 10%) up to 500C. Above 600C, plastic deformation generally increases with increasing test temperature, up to about 50% for samples with lower Ti content at 750C. Although both samples show similar strength in the temperature range from 500C to 800C, the higher Ti content appears to reduce ductility.The main research primarily involved the development of new samples of FeCrAl-based materials with yttrium and titanium oxide additives to assess the feasibility of the designated alloys and their processing for further use in Generation IV reactor technologies. The results suggest that the application of the oxide dispersion enhancement effect can significantly increase the strength of FeCrAl alloys, thus qualifying them as materials potentially suitable for the manufacturing of components and subassemblies used under extreme operating conditions in high-temperature or gas-cooled fast nuclear reactors, including, for example, fuel claddings and hot ducts elements.Oxide dispersion strengthened (ODS) alloys, especially those based on FeCrAl, are recognised for their superior high-temperature strength and irradiation resistance, making them promising candidates for structural components in Generation IV nuclear reactors. Despite their potential, detailed experimental data on their mechanical behaviour at elevated temperatures remain limited, particularly for alloys processed by mechanical alloying and spark plasma sintering (SPS). The study provides new insights into the microstructural characteristics and high-temperature mechanical performance (up to 800 C) of miniaturised FeCrAl–Y2O3–Ti ODS alloy specimens. The originality lies in the specific combination of alloy composition, processing route, and advanced testing methodology, enabling the initial verification of the material’s behaviour under its intended operating conditions. The results contribute to a deeper understanding of how such materials perform in environments relevant to advanced nuclear systems, thus supporting the future application of ODS alloy components.