Jung-Hsien Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jung-Hsien Wu has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Chi-Chuan Wang
Department of Mechanical Engineering, National Yang Ming Chiao Tung University, Hsinchu 300, Taiwan
2 shared publications - Miao-Ru Chen
Green Energy & Environment Research Laboratories, Industrial Technology Research Institute, Hsinchu 310, Taiwan
2 shared publications - Abhishek Kumar
Department of Smart Industry Technology Research and Design National Formosa University, Huwei Township Huwei Yunlin County Taiwan
1 shared publication - Kuo-Shu Hung
Green Energy & Environment Research Laboratories, Industrial Technology Research Institute, Hsinchu 310, Taiwan
1 shared publication - Kuo-Shu Hung
Green Energy & Environment Research Laboratories, Industrial Technology Research Institute, Chutung 310, Taiwan
1 shared publication - Li-Kang Su
Green Energy & Environment Research Laboratories, Industrial Technology Research Institute, Hsinchu 310, Taiwan
1 shared publication
Latest Publications
- Open Access
Heat Transfer Performance of R-1234ze(E) with the Effect of High-Viscosity POE Oil on Enhanced GEWA-B5H Tube
In this study, the heat transfer performance of high-viscosity polyol ester (POE) oil POEA-220 (220 cSt) with low-GWP (global warming potential) refrigerant R-1234ze(E) on enhanced GEWA-B5H tube was investigated at saturation temperatures of 10 °C, 0 °C, and −6 °C. The mass fraction of oil varied from 0.25% to 10%, and all the nucleate pool boiling data were measured at heat fluxes ranging from 10 kW/m2 to 90 kW/m2. The experimental results showed that the heat transfer performance of the R-1234ze(E)/POEA-220 mixtures were superior to the R-1234ze(E)/POEA-68 mixtures. At saturation temperatures of 0 °C and −6 °C, even a 10% mass fraction of the POEA-220 oil showed an enhancement in the HTC (heat transfer coefficient) compared to the pure refrigerant in the moderate heat flux range. On the other hand, for the R-1234ze(E)/POEA-68 mixtures, a 5% mass fraction of oil showed no enhancement in the HTC compared to pure refrigerant at the same saturation temperature. Moreover, at low saturation temperatures (0 °C and −6 °C), the enhancement in the HTC decreased with increasing mass fraction of low-viscosity oil POEA-68, whereas high-viscosity oil POEA-220 showed the highest enhancement in the HTC for a 5% mass fraction of oil at −6 °C saturation temperature compared to the pure refrigerant. The results indicate that for nucleate boiling, the effect of oil viscosity on heat transfer performance is negligible if it contains comparatively high thermal conductivity and low surface tension. In addition, the effect of surface aging on heat transfer performance for the GEAW-B5H tube with pure refrigerant was also reported.
Open AccessHeat Transfer Performance of R-1234ze(E) with the Effect of High-Viscosity POE Oil on Enhanced GEWA-B5H Tube
In this study, the heat transfer performance of high-viscosity polyol ester (POE) oil POEA-220 (220 cSt) with low-GWP (global warming potential) refrigerant R-1234ze(E) on enhanced GEWA-B5H tube was investigated at saturation temperatures of 10 °C, 0 °C, and −6 °C. The mass fraction of oil varied from 0.25% to 10%, and all the nucleate pool boiling data were measured at heat fluxes ranging from 10 kW/m2 to 90 kW/m2. The experimental results showed that the heat transfer performance of the R-1234ze(E)/POEA-220 mixtures were superior to the R-1234ze(E)/POEA-68 mixtures. At saturation temperatures of 0 °C and −6 °C, even a 10% mass fraction of the POEA-220 oil showed an enhancement in the HTC (heat transfer coefficient) compared to the pure refrigerant in the moderate heat flux range. On the other hand, for the R-1234ze(E)/POEA-68 mixtures, a 5% mass fraction of oil showed no enhancement in the HTC compared to pure refrigerant at the same saturation temperature. Moreover, at low saturation temperatures (0 °C and −6 °C), the enhancement in the HTC decreased with increasing mass fraction of low-viscosity oil POEA-68, whereas high-viscosity oil POEA-220 showed the highest enhancement in the HTC for a 5% mass fraction of oil at −6 °C saturation temperature compared to the pure refrigerant. The results indicate that for nucleate boiling, the effect of oil viscosity on heat transfer performance is negligible if it contains comparatively high thermal conductivity and low surface tension. In addition, the effect of surface aging on heat transfer performance for the GEAW-B5H tube with pure refrigerant was also reported.
- Open Access
Performance Improvement of a Double-Layer Microchannel Heat Sink via Novel Fin Geometry—A Numerical Study
This study proposes a novel design having dense fins with lesser thickness at the upper layer and comparatively spare fins with greater thickness in the lower layer to further improve the overall thermal performance of a double-layer microchannel heat sink. The design can effectively direct more low temperature fluid flow toward the lower layer to improve heat transfer while the sparse fin structure at low layer can ease pressure drop penalty. At the same time, the thicker fins at the lower layer ensure higher fin efficiency to facilitate high heat transfer. Parametric and detailed analysis is conducted for the proposed double-layer microchannel heat sink in comparison with the traditional one. After optimization, the thermal resistance of the proposed double-layer microchannel heat sink at the same pumping power is found to be reduced by 9.42% when compared to the traditional double-layer microchannel heat sink. Yet at the same Reynolds number, the Nusselt number of the proposed design exceeds the traditional value by 13%.
Open AccessPerformance Improvement of a Double-Layer Microchannel Heat Sink via Novel Fin Geometry—A Numerical Study
This study proposes a novel design having dense fins with lesser thickness at the upper layer and comparatively spare fins with greater thickness in the lower layer to further improve the overall thermal performance of a double-layer microchannel heat sink. The design can effectively direct more low temperature fluid flow toward the lower layer to improve heat transfer while the sparse fin structure at low layer can ease pressure drop penalty. At the same time, the thicker fins at the lower layer ensure higher fin efficiency to facilitate high heat transfer. Parametric and detailed analysis is conducted for the proposed double-layer microchannel heat sink in comparison with the traditional one. After optimization, the thermal resistance of the proposed double-layer microchannel heat sink at the same pumping power is found to be reduced by 9.42% when compared to the traditional double-layer microchannel heat sink. Yet at the same Reynolds number, the Nusselt number of the proposed design exceeds the traditional value by 13%.