Mustafa Cigdem
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mustafa Cigdem has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Derya Dispinar
SINTEF Industry
3 shared publications Kerem Altug Guler
Istanbul, Turkey
3 shared publications- Fatih Toptan
Department of Materials Science and Engineering Izmir Institute of Technology Izmir Turkey
2 shared publications Rafet Bozdogan
Istanbul, Turkey
2 shared publications- Çağlar Yüksel
Marmara Üniversitesi
2 shared publications A. Binnaz Yoruç Hazar
Yildiz Technical University, Department of Metallurgical and Materials Engineering, Istanbul, Turkey
1 shared publication
Latest Publications
- 22 September 2022
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 17 (3) , 1615-1627
An Analytical Approach for the Correlation Between Bifilm Index and Tensile Properties of AlSi7Mg0.3 (A356) Aluminum Alloy Cleaned via Rotary Degassing and Different Fluxes
- 22 September 2022
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 17 (3) , 1615-1627
An Analytical Approach for the Correlation Between Bifilm Index and Tensile Properties of AlSi7Mg0.3 (A356) Aluminum Alloy Cleaned via Rotary Degassing and Different Fluxes
- Open Access
- 30 March 2022
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 58 (1) , e217
Production and characterization of AA2014-B4C surface-modificated composite via the squeeze casting technique
Metal matrix composite (MMCs) materials provide superiority to monolithic materials in various mechanical properties such as tensile, yield, abrasion resistance, impact resistance by adding reinforcements such as B4C, SiC, Al2O3. While liquid metal processes offer an important advantage, such as low-cost production in high volumes, the heterogeneous clustering of reinforcements in the matrix and the formation of porosity in the area between the reinforcement and matrix pose a problem for composite production. The squeeze casting method stands out in composite production due to its low cost, suitability for mass production, allowing high reinforcement ratio, and ease of homogeneous distribution of reinforcements. In this study, a composite layer reinforced with B4C was produced with a thickness of 1 and 2 mm on a substrate of aluminum 2014 wrought alloy using the squeeze casting method. The mechanical properties of the composite materials produced were characterized via tensile, wear, impact, and hardness tests, and were examined with the help of Scanning Electron Microscopy (SEM). It has been observed that the composite region contains 50 vol.% of B4C reinforcement and the particles of reinforcement were homogeneously distributed into the matrix. All results of the tests mentioned above are better than those obtained in the monolithic 2014 aluminum alloy.
- 30 March 2022
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 58 (1) , e217
Open AccessProduction and characterization of AA2014-B4C surface-modificated composite via the squeeze casting technique
Metal matrix composite (MMCs) materials provide superiority to monolithic materials in various mechanical properties such as tensile, yield, abrasion resistance, impact resistance by adding reinforcements such as B4C, SiC, Al2O3. While liquid metal processes offer an important advantage, such as low-cost production in high volumes, the heterogeneous clustering of reinforcements in the matrix and the formation of porosity in the area between the reinforcement and matrix pose a problem for composite production. The squeeze casting method stands out in composite production due to its low cost, suitability for mass production, allowing high reinforcement ratio, and ease of homogeneous distribution of reinforcements. In this study, a composite layer reinforced with B4C was produced with a thickness of 1 and 2 mm on a substrate of aluminum 2014 wrought alloy using the squeeze casting method. The mechanical properties of the composite materials produced were characterized via tensile, wear, impact, and hardness tests, and were examined with the help of Scanning Electron Microscopy (SEM). It has been observed that the composite region contains 50 vol.% of B4C reinforcement and the particles of reinforcement were homogeneously distributed into the matrix. All results of the tests mentioned above are better than those obtained in the monolithic 2014 aluminum alloy.
- 9 February 2019
- Published by Springer Nature
- p. 273-280
Melt Cleaning Efficiency of Various Fluxes for A356 Alloy
- 9 February 2019
- Published by Springer Nature
- p. 273-280
Melt Cleaning Efficiency of Various Fluxes for A356 Alloy
- 26 December 2017
- Published by Taylor & Francis in International Journal of Cast Metals Research
- Vol. 31 (4) , 1-12
The development of an expansive type special cement bonded investment powder for castings of non ferrous metals and alloys
An attempt has been made to develop an investment powder which expands significantly in the setting period to meet the solidification shrinkage of most metals and alloys. Investment powders consisting of tricalcium aluminate, quartz, various sulphate bearing compounds and a small amounts of controlling agents (additives) were used in the preparation of the block investment molds. A413 Al-Si (Etial 140) alloy was melted and poured in these molds to cast a test specimen of a special geometry. The preliminary results show that it is possible to produce dimensionally accurate castings by using expansive type investment powders. Samples cast into block investment molds prepared from ordinary non-expansive investment powder were smaller than the pattern size, while those poured into molds produced from expansive type powders were the same size or greater than the pattern size.
- 26 December 2017
- Published by Taylor & Francis in International Journal of Cast Metals Research
- Vol. 31 (4) , 1-12
The development of an expansive type special cement bonded investment powder for castings of non ferrous metals and alloys
An attempt has been made to develop an investment powder which expands significantly in the setting period to meet the solidification shrinkage of most metals and alloys. Investment powders consisting of tricalcium aluminate, quartz, various sulphate bearing compounds and a small amounts of controlling agents (additives) were used in the preparation of the block investment molds. A413 Al-Si (Etial 140) alloy was melted and poured in these molds to cast a test specimen of a special geometry. The preliminary results show that it is possible to produce dimensionally accurate castings by using expansive type investment powders. Samples cast into block investment molds prepared from ordinary non-expansive investment powder were smaller than the pattern size, while those poured into molds produced from expansive type powders were the same size or greater than the pattern size.
- Open Access
- 1 September 2016
- Published by Walter de Gruyter GmbH in Archives of Foundry Engineering
- Vol. 16 (3) , 151-156
Quality Evaluation of Remelted A356 Scraps
A356 is one of the widely used aluminium casting alloy that has been used in both sand and die casting processes. Large amounts of scrap metal can be generated from the runner systems and feeders. In addition, chips are generated in the machined parts. The surface area with regard to weight of chips is so high that it makes these scraps difficult to melt. Although there are several techniques evolved to remedy this problem, yet the problem lies in the quality of the recycled raw material. Since recycling of these scrap is quite important due to the advantages like energy saving and cost reduction in the final product, in this work, the recycling efficiency and casting quality were investigated. Three types of charges were prepared for casting: %100 primary ingot, %100 scrap aluminium and fifty-fifty scrap aluminium and primary ingot mixture were used. Melt quality was determined by calculating bifilm index by using reduced pressure test. Tensile test samples were produced by casting both from sand and die moulds. Relationship between bifilm index and tensile strength were determined as an indication of correlation of melt quality. It was found that untreated chips decrease the casting quality significantly. Therefore, prior to charging the chips into the furnace for melting, a series of cleaning processes has to be used in order to achieve good quality products.
- 1 September 2016
- Published by Walter de Gruyter GmbH in Archives of Foundry Engineering
- Vol. 16 (3) , 151-156
Open AccessQuality Evaluation of Remelted A356 Scraps
A356 is one of the widely used aluminium casting alloy that has been used in both sand and die casting processes. Large amounts of scrap metal can be generated from the runner systems and feeders. In addition, chips are generated in the machined parts. The surface area with regard to weight of chips is so high that it makes these scraps difficult to melt. Although there are several techniques evolved to remedy this problem, yet the problem lies in the quality of the recycled raw material. Since recycling of these scrap is quite important due to the advantages like energy saving and cost reduction in the final product, in this work, the recycling efficiency and casting quality were investigated. Three types of charges were prepared for casting: %100 primary ingot, %100 scrap aluminium and fifty-fifty scrap aluminium and primary ingot mixture were used. Melt quality was determined by calculating bifilm index by using reduced pressure test. Tensile test samples were produced by casting both from sand and die moulds. Relationship between bifilm index and tensile strength were determined as an indication of correlation of melt quality. It was found that untreated chips decrease the casting quality significantly. Therefore, prior to charging the chips into the furnace for melting, a series of cleaning processes has to be used in order to achieve good quality products.
- 1 January 2013
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 55 (1) , 60-63
Drilling Template Used to Produce Cellular EPS Patterns for the Lost Foam Casting Process
Cellular metals differ from the other materials by a lower density which is their characteristic property. Besides, they show unusual physical, mechanical, thermal, acoustic and electrical properties. Even though they have lots of pores compared to solid materials they can show a unique combination of several properties that cannot be obtained in a conventional material at the same time. There are several kinds of production methods for cellular materials. Nowadays, lots of researches have been carried out with respect to new production methods. The lost foam process, which bases on evaporating the polystyrene foam model, reduces the process steps of investment casting and can be an alternative method to many production methods. In this study, open cell samples were produced with two different aluminium alloys by using the lost foam casting technique. A413 as a casting alloy and A6063 as a wrought alloy were selected for casting experiments. After production of these two aluminium alloys, the decrease in weight, compression strengths, deformation ratios were determined and compared to each other.
- 1 January 2013
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 55 (1) , 60-63
Drilling Template Used to Produce Cellular EPS Patterns for the Lost Foam Casting Process
Cellular metals differ from the other materials by a lower density which is their characteristic property. Besides, they show unusual physical, mechanical, thermal, acoustic and electrical properties. Even though they have lots of pores compared to solid materials they can show a unique combination of several properties that cannot be obtained in a conventional material at the same time. There are several kinds of production methods for cellular materials. Nowadays, lots of researches have been carried out with respect to new production methods. The lost foam process, which bases on evaporating the polystyrene foam model, reduces the process steps of investment casting and can be an alternative method to many production methods. In this study, open cell samples were produced with two different aluminium alloys by using the lost foam casting technique. A413 as a casting alloy and A6063 as a wrought alloy were selected for casting experiments. After production of these two aluminium alloys, the decrease in weight, compression strengths, deformation ratios were determined and compared to each other.
- 24 January 2012
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 445, 349-354
Casting Quality of Gypsum Bonded Block Investment Casting Moulds
In this study surface finish and dimensional charactersitics of castings produced with gypsum bonded block investment moulds were investigated. Commercial and laboratory made gypsum bonded investment moulds were used for investment casting mould making. To compare the casting quality of the investment powders, wax patterns for surface roughness specimens and linear dimension measurement specimens were designed and produced with special geometry. Wax trees were assembled with these patterns, cylindrical stainless steel perforated flasks were settled around the trees and gypsum bonded investment slurries were filled into flasks. Conventional tin bronze was subsequently cast into these moulds by vacuum assisted casting process. Afterwards, surface roughnesses of specimens were measured and linear dimensions of wax patterns and cast specimens were compared to determine percantage of dimensional change.
- 24 January 2012
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 445, 349-354
Casting Quality of Gypsum Bonded Block Investment Casting Moulds
In this study surface finish and dimensional charactersitics of castings produced with gypsum bonded block investment moulds were investigated. Commercial and laboratory made gypsum bonded investment moulds were used for investment casting mould making. To compare the casting quality of the investment powders, wax patterns for surface roughness specimens and linear dimension measurement specimens were designed and produced with special geometry. Wax trees were assembled with these patterns, cylindrical stainless steel perforated flasks were settled around the trees and gypsum bonded investment slurries were filled into flasks. Conventional tin bronze was subsequently cast into these moulds by vacuum assisted casting process. Afterwards, surface roughnesses of specimens were measured and linear dimensions of wax patterns and cast specimens were compared to determine percantage of dimensional change.
- 1 September 2011
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 53 (9) , 551-555
Surface Quality and Dimensional Accuracy of Gypsum Bonded Investment Flask Casting Moulds
In this study surface finish and dimensional charactersitics of castings produced with gypsum bonded block investment moulds were investigated. Commercial and laboratory made gypsum bonded investment moulds were used for investment casting mould making. To compare the casting quality of the investment powders, wax patterns for surface roughness specimens and linear dimension measurement specimens were designed and produced with special geometry. Wax trees were assembled with these patterns, cylindrical stainless steel perforated flasks were settled around the trees and gypsum bonded investment slurries were filled into flasks. Conventional tin bronze and sterling silver were subsequently cast into these moulds by vacuum assisted and vacuum pressure casting processes, respectively. Afterwards, surface roughness of specimens were measured and linear dimensions of wax patterns and cast specimens were compared to determine percentage of dimensional change.
- 1 September 2011
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 53 (9) , 551-555
Surface Quality and Dimensional Accuracy of Gypsum Bonded Investment Flask Casting Moulds
In this study surface finish and dimensional charactersitics of castings produced with gypsum bonded block investment moulds were investigated. Commercial and laboratory made gypsum bonded investment moulds were used for investment casting mould making. To compare the casting quality of the investment powders, wax patterns for surface roughness specimens and linear dimension measurement specimens were designed and produced with special geometry. Wax trees were assembled with these patterns, cylindrical stainless steel perforated flasks were settled around the trees and gypsum bonded investment slurries were filled into flasks. Conventional tin bronze and sterling silver were subsequently cast into these moulds by vacuum assisted and vacuum pressure casting processes, respectively. Afterwards, surface roughness of specimens were measured and linear dimensions of wax patterns and cast specimens were compared to determine percentage of dimensional change.
- 28 February 2011
- Published by Wiley
- p. 837-842
Microstructural Properties and Wear Behaviour of AlSi9Mg Matrix B 4 C p Reinforced Composites
- 28 February 2011
- Published by Wiley
- p. 837-842
Microstructural Properties and Wear Behaviour of AlSi9Mg Matrix B 4 C p Reinforced Composites
- Top Cited Papers
- 1 June 2010
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 31, S87-S91
Processing and microstructural characterisation of AA 1070 and AA 6063 matrix B4Cp reinforced composites
- 1 June 2010
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 31, S87-S91
Top Cited PapersProcessing and microstructural characterisation of AA 1070 and AA 6063 matrix B4Cp reinforced composites