Lei Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Lei Zheng has a total of 103 co-authors. Here are the top co-authors by number of shared publications:
Ye Meng
Institute of Advanced Materials and Technology, University of Science and Technology Beijing, Beijing, P.R. China
12 shared publications- Boning Zhang
School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China
7 shared publications Guowei Wang
School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing, China
5 shared publicationsHongliang Liu
School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing, China
5 shared publicationsLan Liu
School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing, China
5 shared publicationsMin Xu
School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing, China
4 shared publications
Latest Publications
- Open Access
Microstructural Evolution, Microhardness, and Residual Stress in FGH4097 Superalloy Subjected to Cold Expansion
Cold expansion is widely used to improve the fatigue resistance of aerospace structures with holes. To address the strengthening requirements of holes in FGH4097 superalloy components, this study systematically investigated the effects of cold expansion on microhardness, residual stress, and microstructural evolution. An L9(34) orthogonal design was used to evaluate the effects of the mandrel-hole interference level, lead angle, lubrication condition, and mandrel speed on the microhardness and residual stress of FGH4097. Electron backscatter diffraction, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used to characterize the deformation microstructure and explore strengthening mechanisms. Results show that cold expansion produced a pronounced radial microhardness gradient and compressive residual stress field. The maximum near-hole microhardness was 538 HV, approximately 36% higher than that of the base material, and the largest compressive residual stress of −629.4 MPa was observed in the same specimen. Range analysis identified the mandrel-hole interference level as the dominant processing parameter for both microhardness and residual stress. The near-hole region exhibited increased local misorientation, microstrain, and dislocation density, and dense dislocation tangling and piling-ups at γ/γ′ interfaces were observed. The microhardness increase can primarily be attributed to dislocation multiplication, dislocation interactions, and the impediment of dislocation motion by γ′ precipitates.
Open AccessMicrostructural Evolution, Microhardness, and Residual Stress in FGH4097 Superalloy Subjected to Cold Expansion
Cold expansion is widely used to improve the fatigue resistance of aerospace structures with holes. To address the strengthening requirements of holes in FGH4097 superalloy components, this study systematically investigated the effects of cold expansion on microhardness, residual stress, and microstructural evolution. An L9(34) orthogonal design was used to evaluate the effects of the mandrel-hole interference level, lead angle, lubrication condition, and mandrel speed on the microhardness and residual stress of FGH4097. Electron backscatter diffraction, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used to characterize the deformation microstructure and explore strengthening mechanisms. Results show that cold expansion produced a pronounced radial microhardness gradient and compressive residual stress field. The maximum near-hole microhardness was 538 HV, approximately 36% higher than that of the base material, and the largest compressive residual stress of −629.4 MPa was observed in the same specimen. Range analysis identified the mandrel-hole interference level as the dominant processing parameter for both microhardness and residual stress. The near-hole region exhibited increased local misorientation, microstrain, and dislocation density, and dense dislocation tangling and piling-ups at γ/γ′ interfaces were observed. The microhardness increase can primarily be attributed to dislocation multiplication, dislocation interactions, and the impediment of dislocation motion by γ′ precipitates.
- 24 August 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- p. 1-10
Opposite Solidification Segregation Behavior of 718 and 718Plus Alloys Caused by Pt
- 24 August 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- p. 1-10
Opposite Solidification Segregation Behavior of 718 and 718Plus Alloys Caused by Pt
- Open Access
Preparation of Spherical δ-Nb3Al Powders and Their Phase Transition Behavior in Powder Metallurgy Nickel-Based Superalloys During Hot Isostatic Pressing
The feasibility of using brittle δ-Nb3Al as the reinforcement phase in powder metallurgy nickel-based superalloys depends on both the preparation of near-spherical particles and their phase stability during hot isostatic pressing (HIP). In this study, irregular δ-Nb3Al particles were converted into near-spherical reinforcement particles by controlled ball milling. The optimized milling condition for obtaining high-sphericity δ-Nb3Al particles was 200 r/min for 20 h. The morphological evolution during ball milling clarifies a particle-rounding mechanism governed by edge elimination, fine-fragment adhesion, surface consolidation, and re-fragmentation. During subsequent HIP consolidation to introduce the particles into a nickel-based superalloy, extensive interdiffusion occurred between δ-Nb3Al and the surrounding matrix, resulting in the formation of multilayer interfacial reaction zones and multiple Nb-rich secondary phases, including Laves-(Ni, Cr)2Nb, Ni6Nb7, Nb solid solution, and Ni3Nb. Quantitative analysis indicates that the retained volume fraction of δ-Nb3Al after HIP is only about 9.85%, much lower than the initial addition level. Combined with thermodynamic analysis based on the effective heat of formation model, the results show that the final phase constitution is governed by the coupled effects of diffusion kinetics and thermodynamic driving force. These findings clarify the intrinsic processing–microstructure–phase transition relationship in δ-Nb3Al-reinforced powder metallurgy nickel-based superalloys, showing that ball milling controls the powder-state evolution of δ-Nb3Al, whereas diffusion-driven interfacial reactions during HIP govern its retention and final phase constitution.
Open AccessPreparation of Spherical δ-Nb3Al Powders and Their Phase Transition Behavior in Powder Metallurgy Nickel-Based Superalloys During Hot Isostatic Pressing
The feasibility of using brittle δ-Nb3Al as the reinforcement phase in powder metallurgy nickel-based superalloys depends on both the preparation of near-spherical particles and their phase stability during hot isostatic pressing (HIP). In this study, irregular δ-Nb3Al particles were converted into near-spherical reinforcement particles by controlled ball milling. The optimized milling condition for obtaining high-sphericity δ-Nb3Al particles was 200 r/min for 20 h. The morphological evolution during ball milling clarifies a particle-rounding mechanism governed by edge elimination, fine-fragment adhesion, surface consolidation, and re-fragmentation. During subsequent HIP consolidation to introduce the particles into a nickel-based superalloy, extensive interdiffusion occurred between δ-Nb3Al and the surrounding matrix, resulting in the formation of multilayer interfacial reaction zones and multiple Nb-rich secondary phases, including Laves-(Ni, Cr)2Nb, Ni6Nb7, Nb solid solution, and Ni3Nb. Quantitative analysis indicates that the retained volume fraction of δ-Nb3Al after HIP is only about 9.85%, much lower than the initial addition level. Combined with thermodynamic analysis based on the effective heat of formation model, the results show that the final phase constitution is governed by the coupled effects of diffusion kinetics and thermodynamic driving force. These findings clarify the intrinsic processing–microstructure–phase transition relationship in δ-Nb3Al-reinforced powder metallurgy nickel-based superalloys, showing that ball milling controls the powder-state evolution of δ-Nb3Al, whereas diffusion-driven interfacial reactions during HIP govern its retention and final phase constitution.
- 28 February 2026
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 33 (4) , 103
Influence of high-content cobalt on hierarchical martensitic microstructures and mechanical properties of stainless maraging steels
- 28 February 2026
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 33 (4) , 103
Influence of high-content cobalt on hierarchical martensitic microstructures and mechanical properties of stainless maraging steels
- 30 December 2024
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 56 (2) , 1127-1138
Wall-Thickness-Related Solidification Microstructure Variations in Domed Ni–Co–W Castings: Modelling and Experiment
- 30 December 2024
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 56 (2) , 1127-1138
Wall-Thickness-Related Solidification Microstructure Variations in Domed Ni–Co–W Castings: Modelling and Experiment
- Open Access
- 18 December 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (2)
Enhanced Oxidation Resistance of Pt‐Containing Inconel 718 Alloy through Facilitated Formation of Protective Chromia
This study investigates the influence of Pt addition on the oxidation behavior of a Cr2O3‐forming superalloy. Inconel 718 (IN718) alloys with varying Pt content were prepared and subjected to isothermal oxidation tests. The results demonstrate that Pt significantly enhances the oxidation resistance of IN718, as evidenced by reduced weight gain, thinner oxide layers, and smaller oxide particles. Pt addition also increases the activation energy for both initial interface oxidation and ion diffusion during long‐term oxidation. Furthermore, Pt promotes the formation of a Cr2O3 layer while suppressing the formation of other undesirable oxides, resulting in a more cohesive and stable oxide layer. The improved oxidation resistance is attributed to two key factors: during the initial oxidation stage, Pt, as a noble element, reduces the activity of the primary oxide‐forming element Cr to oxidative environments, thereby lowering its susceptibility to initial oxidation at the metal–oxidant interface. During long‐term oxidation, Pt preferentially substitutes for Ni in major phases such as γ‐Ni(Cr,Fe) and γ′‐Ni3(Al,Ti), locally increasing the Cr composition. This promotes Cr oxidation, effectively suppressing the oxidation of Ni or Fe. These findings suggest that Pt addition is a promising approach for enhancing oxidation resistance in alloy design.
- 18 December 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (2)
Open AccessEnhanced Oxidation Resistance of Pt‐Containing Inconel 718 Alloy through Facilitated Formation of Protective Chromia
This study investigates the influence of Pt addition on the oxidation behavior of a Cr2O3‐forming superalloy. Inconel 718 (IN718) alloys with varying Pt content were prepared and subjected to isothermal oxidation tests. The results demonstrate that Pt significantly enhances the oxidation resistance of IN718, as evidenced by reduced weight gain, thinner oxide layers, and smaller oxide particles. Pt addition also increases the activation energy for both initial interface oxidation and ion diffusion during long‐term oxidation. Furthermore, Pt promotes the formation of a Cr2O3 layer while suppressing the formation of other undesirable oxides, resulting in a more cohesive and stable oxide layer. The improved oxidation resistance is attributed to two key factors: during the initial oxidation stage, Pt, as a noble element, reduces the activity of the primary oxide‐forming element Cr to oxidative environments, thereby lowering its susceptibility to initial oxidation at the metal–oxidant interface. During long‐term oxidation, Pt preferentially substitutes for Ni in major phases such as γ‐Ni(Cr,Fe) and γ′‐Ni3(Al,Ti), locally increasing the Cr composition. This promotes Cr oxidation, effectively suppressing the oxidation of Ni or Fe. These findings suggest that Pt addition is a promising approach for enhancing oxidation resistance in alloy design.
- 13 July 2024
- Published by Springer Nature in Journal of Materials Science
- Vol. 59 (28) , 13345-13361
The high-temperature oxidation behavior and mechanism in a powder metallurgy Ni-based superalloy featuring δ-Nb3Al addition
- 13 July 2024
- Published by Springer Nature in Journal of Materials Science
- Vol. 59 (28) , 13345-13361
The high-temperature oxidation behavior and mechanism in a powder metallurgy Ni-based superalloy featuring δ-Nb3Al addition
- 9 May 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (7) , 5713-5720
Prediction of Phase Formation Sequence in Multicomponent NiCoW/Nb3Al Interface
- 9 May 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (7) , 5713-5720
Prediction of Phase Formation Sequence in Multicomponent NiCoW/Nb3Al Interface
- 18 October 2023
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 311
Hot workability optimization of W400 non-oriented silicon steel
- 18 October 2023
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 311
Hot workability optimization of W400 non-oriented silicon steel
- Open Access
Oxidation Property of a Fourth-Generation Powder Metallurgy FGH4108 Nickel-Based Superalloy
Isothermal oxidation kinetics of a fourth-generation powder metallurgy FGH4108 nickel-based superalloy is investigated at 800 °C to 1100 °C by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). At 800 °C and 900 °C, the oxidation kinetic curves of the FGH4108 superalloy follow parabolic law. At 1000 °C, the oxidation kinetic curve follows cubic law. At 1100 °C, the oxidation kinetic curve has two distinct parts: the first part follows a parabolic law, and the second one obeys a linear law. Cross-sectional morphologies and elemental distributions show that the oxide film consists of two parts at 800 °C: the outer layer is a continuous dense protective Cr2O3 oxide film, and the inner layer is a discontinuous Al2O3 oxide layer. At 900–1100 °C, the oxides consist of three layers: the outermost is the oxides of Cr2O3 and TiO2, the middle is a continuous oxide of Al2O3, and the innermost is dotted oxides of TiO2. The thickness of the inner TiO2 oxide layer increases with the increase of oxidation temperature. On this basis, the oxidation behavior of the FGH4108 superalloy at high temperatures is confirmed to be controlled by the diffusion of Cr, Al, Ti, and O. From the aspect of oxidation resistance, the long-term service temperature of the FGH4108 superalloy should not exceed 1000 °C.
Open AccessOxidation Property of a Fourth-Generation Powder Metallurgy FGH4108 Nickel-Based Superalloy
Isothermal oxidation kinetics of a fourth-generation powder metallurgy FGH4108 nickel-based superalloy is investigated at 800 °C to 1100 °C by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). At 800 °C and 900 °C, the oxidation kinetic curves of the FGH4108 superalloy follow parabolic law. At 1000 °C, the oxidation kinetic curve follows cubic law. At 1100 °C, the oxidation kinetic curve has two distinct parts: the first part follows a parabolic law, and the second one obeys a linear law. Cross-sectional morphologies and elemental distributions show that the oxide film consists of two parts at 800 °C: the outer layer is a continuous dense protective Cr2O3 oxide film, and the inner layer is a discontinuous Al2O3 oxide layer. At 900–1100 °C, the oxides consist of three layers: the outermost is the oxides of Cr2O3 and TiO2, the middle is a continuous oxide of Al2O3, and the innermost is dotted oxides of TiO2. The thickness of the inner TiO2 oxide layer increases with the increase of oxidation temperature. On this basis, the oxidation behavior of the FGH4108 superalloy at high temperatures is confirmed to be controlled by the diffusion of Cr, Al, Ti, and O. From the aspect of oxidation resistance, the long-term service temperature of the FGH4108 superalloy should not exceed 1000 °C.