KMKonstantin I. Muntean

Konstantin I. Muntean

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Konstantin I. Muntean has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Propagation of an Azimuthally Polarized Terahertz Laser Beams with a Phase Singularity

    by Andrey V. Degtyarev, Mykola M. Dubinin, Vyacheslav A. Maslov, Konstantin I. Muntean, Vladislav S. Senyuta

    Analytical expressions are derived to describe the nonparaxial diffraction of modes in a dielectric waveguide resonator for a terahertz laser. The study examines the interaction between azimuthally polarized TE0m (m = 1, 2, 3) modes and a spiral phase plate (SPP), accounting for its different topological charges (n). Using numerical modeling, the emerging physical properties of vortex beams are investigated when they propagate in free space. Vector integral Rayleigh-Sommerfeld transforms are used to study the propagation in the Fresnel zone of vortex laser beams excited by TE0m modes of a dielectric waveguide quasi-optical resonator when they are incident on a phase plate. In the studied modes, in the absence of a phase plate, the field exhibits a ring-shaped transverse intensity distribution along the propagation axis. In this case, the number of rings in the cross-section corresponds to the azimuthal number of modes, and the phase distributions for the transverse components of these modes have opposite signs. The use of a SPP with a topological charge n = 1 changes the structure of the beam field, forming an axial maximum in the transverse profile with an increase in the beam diameter at this maximum compared to the case without a phase plate. At the same time the phase structure of the field for transverse components acquires two-lobe symmetry. When using a SPP with a topological charge n = 2 for the TE01 mode the restoration of the ring-like field structure is observed and for the TE02 and TE03 modes the formation of regions of increased intensity is observed. In this case, the phase distributions of the field components for the TE01 and TE02 modes acquire a three-lobe spiral structure, whereas those for the TE03 mode acquire a multi-lobe spiral configuration.


  • Open Access

    Spatial Dynamics of a Radially Polarized Terahertz Laser Beam with a Phase Singularity

    by Andrey V. Degtyarev, Mykola M. Dubinin, Vyacheslav Maslov, Konstantin I. Muntean, Oleh O. Svystunov

    Analytical expressions are obtained that describe the nonparaxial diffraction in free space of the TM01 mode with radial polarization of the field of the dielectric waveguide resonator of a terahertz laser during its interaction with a spiral phase plate with different topological charge (n). The physical features of the obtained vortex beams during their propagation and tight focusing are studied by numerical simulation. The integral diffraction Rayleigh-Sommerfeld transforms are used to simulate the propagation and focusing of the obtained beams. In free space the use of the spiral phase plate at the waveguide output with a topological charge of n = 1 leads to a change in the transverse beam profile from annular to a beam that has a field maximum on the axis, and then for n = 2 again to annular. During focusing the transverse distribution of the total field intensity in the absence of a spiral phase plate has a ring structure. In this case there is a slight intensity on the axis due to the contribution of the longitudinal component of the field. The transverse profile of the beam changes in the same way as during its propagation when using a phase plate. In this case the phase front changes from spherical to spiral with the presence of two (n = 1) and four (n = 2) branching vortices.


  • Open Access

    Interferometric Locating the Waist of a Laser Beam

    by Vyacheslav A. Maslov, Konstantin I. Muntean

    An interferometric method for determining the location of a laser beam waist has been developed, which implements the dependence of the wavefront curvature on its distance to the waist. The initial laser beam, the waist location of which must be determined, is split by a shear interferometer into reference and information beams, which form a spatially non-localized interference field in reflected light. The period of the interference fringes observed in any cross-section of the interference field carries information about the location of the waist of the initial laser beam relative to this section. The distance from the waist to the plane of recording the period of the interference fringes is calculated using the formulas of Gaussian optics. The fundamental difference of this method from currently known ones allows for increasing the accuracy of the obtained result while simultaneously reducing the laboriousness of the measurement process.


  • Open Access

    Determination of the laser beam waist

    by M. M. Dubinin, V. A. Maslov, К. І. Muntean

    Background: An interferometric method for measuring the position of the beam waist of laser radiation, which defines the origin of the coordinate system for the spatial parameters of the beam, is considered. Information about the location of the beam waist plays a crucial role in laser ballistic gravimetry, laser interferometry of lengths, optical metrology, and precision laser barometry. The aim of the work: Improving the accuracy of beam waist location while simultaneously reducing the complexity of the measurement process. Materials and methods: A method has been proposed that leverages the dependence of the wavefront curvature of the beam on the distance to the beam waist. The initial laser beam is split into a reference and an information beam using a shear interferometer, forming a nonlocalized interference field in the reflected light. The period of the interference fringes, observed at any cross-section of the interference field, contains information about the position of the beam waist relative to this cross-section. The distance from the beam waist to the plane where the fringe period is registered is calculated using Gaussian optics formulas. Results: An interferometric method for determining the position of the laser beam waist has been developed, implementing the known relationship between the wavefront curvature in a given cross-section of the radiation beam and the distance from this cross-section to the beam waist. Experimental studies confirmed the viability of the interferometric method for determining the position of the laser beam waist. The obtained results allow recommending this method as the most accurate currently available. Conclusion: Studies of measurement devices revealed that for the LG-56 laser with a divergence angle of about 10', both methods ensure result consistency with an accuracy of approximately 2%. However, as the divergence angle decreases, particularly with changes in the beam waist position, the accuracy of result consistency diminishes. The cross-section method, recommended by ISO 11146-1 standards, is appropriate for determining the beam waist position for beams with divergence angles exceeding 30", though it involves an error of about 10%. The limitations of this method arise from increased errors in determining the waist position. The interferometric method is effective for identifying beam waists with divergence angles exceeding 5', providing an error of no more than 5%.

  • Open Access

    Propagation of vortex laser beams of a metal resonator

    by A. V. Degtyarev, M. M. Dubinin, V. A. Maslov, K. I. Muntean, O. O. Svystunov

    Background: The problem of radiation propagation of vortex laser beams of a metal waveguide laser is considered. The results of the propagation of such beams have a wide range of potential applications, from imaging and spectroscopy to communication, sensing, biomedicine, and solving problems related to the interaction of electromagnetic waves with matter: diagnostics of thin films, surfaces of materials, various biological objects, as well as astronomy and space research. The aim of the work is to obtain analytical expressions for the description of non-paraxial mode diffraction of the waveguide metal resonator of a terahertz laser during their interaction with a spiral phase plate and to study the physical features of the obtained vortex beams during their propagation in free space by means of numerical modeling. Materials and methods: The Rayleigh-Sommerfeld vector theory was used to study the propagation of vortex laser beams in the Fresnel zone, which were excited by the modes of a metal waveguide quasi-optical resonator. Results: Analytical expressions were obtained to describe the non-paraxial mode diffraction of the metal waveguide resonator of a terahertz laser. Also, with the help of numerical modeling, the physical features of emerging vortex beams during their propagation in free space were investigated. Conclusion: In free space, the spiral phase plate for the excitation of the TE11 mode from the profile with the intensity maximum in the center (n = 0) forms an asymmetric ring with two maxima (n = 1, 2). For the TE01 excitation mode, the initial ring (n = 0) structure of the field strength is transformed into a structure with maximum radiation intensity in the center (n = 1), and then again into a ring (n = 2). The phase front of the beam for the Ey component linearly polarized along the y axis of the TE11 mode changes from spherical to helical with one singularity point on the axis. In the phase profile of the transverse components of the TE01 azimuthally polarized mode, a section with two and three off-axis points of phase singularities appears.

  • Open Access

    Evolution of Vector Vortex Beams Formed by a Terahertz Laser Metal Resonator

    by Andrey V. Degtyarev, Mykola M. Dubinin, Vyacheslav A. Maslov, Konstantin I. Muntean, Oleh O. Svystunov

    Analytical expressions for the nonparaxial mode diffraction of a terahertz laser metal waveguide resonator are obtained. The study assumes interaction between the modes and a spiral phase plate, considering different topological charges (n). Also, using numerical modeling, the physical features of the emerging vortex beams as they propagate in free space are studied. The Rayleigh-Sommerfeld vector theory is employed to investigate the propagation of vortex laser beams in the Fresnel zone, excited by the modes of a metal waveguide quasi-optical resonator upon incidence on a spiral phase plate. In free space, the spiral phase plate for exciting TE11 mode from the profile with the intensity maximum in the center (n = 0) forms an asymmetric ring one with two maxima (n = 1, 2). For the exciting TE01 mode, the initial ring (n = 0) structure of the field intensity is transformed into a structure with a maximum radiation intensity in the center (n = 1), and later again into a ring (n = 2). The phase front of the beam for the Ey component of the linearly polarized along the y axis TE11 mode changes from spherical to spiral with one on-axis singularity point. In the phase profile of the transverse components of the azimuthally polarized TE01 mode, a region with two and three off-axis phase singularity points appears.

  • Open Access

    Selection and focusing of higher-order modes in a CW waveguide terahertz laser

    by O. V. Gurin, A. V. Degtyarev, M. M. Dubinin, V. A. Maslov, K. I. Muntean, V. M. Ryabykh, O. O. Svystunov, V.S. Senyuta

    Background: The problems of selection and focusing of higher order modes of a dielectric waveguide laser are considered. The proposed and investigated scheme of mode selection in waveguide quasi-optical resonators can be used in the development and creation of new designs of laser systems with controlled characteristics for scientific and applied research - single-mode lasers with a given shape and polarization of the output beam. The results of laser beam focusing research can be used to solve problems related to the interaction of electromagnetic waves with matter: diagnostics of the surface of materials, thin films, biological objects, achieving subwavelength resolution of THz tomography, for radar and telecommunications applications, etc. The aim of the work is to establish the physical laws of selection and focusing of wave laser beams of continuous radiation of the terahertz range with different spatial polarization. Materials and methods: The matrix method was used to calculate the mode characteristics of a waveguide laser resonator with an inhomogeneous phase-stepped mirror. The Rayleigh-Sommerfeld vector theory was used to study the propagation and focusing of laser beams excited by modes of a waveguide quasi-optical resonator in different diffraction zones. Well-known methods of measuring the THz range were used for the experimental study of the studied phenomena. Results: For the first time, a method of selection of higher EH12q-mode in a terahertz laser resonator based on the placement of a groove 2.3 – 2.8 l wide on the surface of one of the resonator mirrors was proposed, theoretically substantiated and experimentally confirmed. This can significantly increase losses for all undesirable modes. At the same time, the losses for the higher EH12q-mode remain practically unchanged, which creates conditions for its predominant excitation. Theoretical and experimental studies of moderate and sharp focusing in the free space of higher-order modes with different spatial polarizations of the dielectric waveguide resonator have been carried out. Conclusion: It is shown that the proposed phase-stepped mirror with a groove effectively selects the required higher transverse mode. It is shown that the linearly polarized EH12q -mode has the maximum field intensity in the focal region of the lens. For azimuthally polarized TE02q - and TE03q-modes, the central lobes have a maximum of the field, which is significantly shifted from the lens focus. With sharp focusing in the field distribution in the radially polarized TМ02q - and TМ03q-modes, an increase in axial intensity is observed. In this case, their central lobes, as in the higher TE0nq -modes, are markedly offset from the focus of the lens.

  • Control of tightly focused laser beams in the THz range

    by Andrey V. Degtyarev, Mykola M. Dubinin, Oleg V. Gurin, Vyacheslav A. Maslov, Konstantin I. Muntean, Valeriy N. Ryabyh, Vladislav S. Senyuta

    The possibility for control of tightly focused laser beams excited by the resonator modes of a THz laser based on a hollow circular dielectric waveguide is studied theoretically and experimentally. The wavelength of the radiation under study is 0.4326 mm corresponding to the generation line of the optically pumped HCOOH‐molecule THz laser. The focusing system is implemented by a short‐focus lens covered by absorbing masks in the central region. The focal area parameters were controlled by changing the size of the masks. The electric field components of the laser modes are calculated using the Rayleigh‐Sommerfeld integral transformations under non‐paraxial approximation. The use of absorbing masks made it possible to reduce the beam diameter in the focal region and increase the depth of focus of the linearly polarized EH11‐mode and azimuthally polarized TE01‐mode as well. In this case, despite of the presence of an absorbing mask, the distribution of the total field intensity of the TE01‐mode retained its annular shape, and the field maximum of the EH11‐mode is observed at center of the focal spot. The results of this work can be implemented in medical diagnostics, high‐speed communications, and environmental monitoring.


  • Focusing of Modes for Metallic Resonator of a Terahertz Laser with Nonuniform Spatial Polarization

    by O. V. Gurin, A. V. Degtyarev, M. M. Dubinin, V. A. Maslov, K. I. Muntean, V. N. Ryabykh

    Theoretically, based on the Rayleigh-Sommerfeld vector theory using the radiation of a waveguide terahertz laser (λ = 432.6 μm), physical features of moderate and sharp focusing of radiation beams were studied. Laser beams are excited by the modes of a laser cavity based on a circular metal waveguide for inhomogeneous spatial polarization of the field. It is shown that in the focal region of the lens, in the case of a moderate and sharp focusing of the radiation beam excited by the TM 11 mode with a nonuniform polarization, a minimum of its axial intensity is observed. It is due to the significant influence in this case of the intensity of the longitudinal component of the field of the given mode. The obtained results expand the knowledge about the features of the focusing for the laser beams of terahertz range.


  • SELECTIVE PROPERTIES OF AZIMUTHAL-SYMMETRIC DIFFRACTION MIRRORS OF TERAHERTZ LASER

    by O. V. Gurin, А. V. Degtyarev, N. N. Dubinin, M. N. Legenkiy, V. A. Maslov, K. I. Muntean, V. N. Ryabykh, V. S. Senyuta

    In recent years interest in light fields with inhomogeneous spatial polarization known in scientific literature as "vector beams" has increased. Among them beams with radial and azimuthal polarization of radiation attract the greatest practical interest. Taking into account the features of their propagation and focusing such beams are used for solving various problems in laser physics, biomedical diagnostics, in metal processing technology, high-speed communication, to accelerate electrons etc. The methods and approaches used in forming of laser beams with the required spatial polarization structure in terahertz band are developed only in some papers, and all of them are predominantly referred to the extra-cavity group of methods. For effective intracavity excitation of the transverse mode with inhomogeneous spatial polarization of radiation, the selective properties of the output mirrors of a waveguide HCOOH laser were investigated. The mirrors are made in the form of azimuthally symmetric multiring metal diaphragms with the different periods located on a quartz crystal substrate. Good polarization-selective properties of the small-scale diffraction mirror are shown when generating azimuthally symmetric modes of a terahertz laser. Diffraction mirrors with a period close to the wavelength are investigated numerically. Good selective characteristics of these mirrors for the generation of radially polarized terahertz laser modes are shown. The absence of polarization-selective properties of large-scale mirrors when using them as output mirrors of a terahertz laser is shown theoretically and experimentally confirmed.