Oleksandr Serbul
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Oleksandr Serbul has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Vasyl Kondratets
Центральноукраїнський національний технічний університет, м. Кропивницький
5 shared publications - Oleksandr Didyk
Центральноукраїнський національний технічний університет
4 shared publications Central Ukrainian National Technical University
2 shared publicationsAnatolii Matsui
1 shared publication- Oles Іzovita
Central Ukrainian National Technical University
1 shared publication - Sergei Osadchy
Ukrainian State Flight Academy
1 shared publication
Latest Publications
- 26 May 2025
- Published by Central Ukrainian National Technical University in Central Ukrainian Scientific Bulletin. Technical Sciences
- Vol. 2 (11(42))
Analysis of the Control Object for the Development of a System for Automatic Stabilization of the Loading of the Threshing Machine of a Combine Harvester
Oleksandr Didyk, Associate Professor, Candidate of Technical Sciences, Head of the Department of Automation of Production Processes, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, https://orcid.org/0000-0003-1454-0828, e-mail: didyk_s79@ukr.net Oleksandr Serbul, Associate Professor, Candidate of Technical Sciences, Associate Professor of the Department of Automation of Production Processes, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, https://orcid.org/ 0000-0003-1836-5529, e-mail: serbulan@ukr.net Serhiy Teslya, PhD student in Automation, computer-integrated technologies and robotics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0009-0001-7294-2465, e-mail: tesliasv@ukr.net This article provides an analysis of the control object, considers factors that complicate the achievement of maximum quality stabilization of the threshing machine loading, including the dynamic characteristics of the elements of the control object, the dynamic characteristics of the disturbances acting on the control object. To achieve the maximum quality of stabilization of the threshing machine loading of a combine harvester, it is necessary to apply methods of dynamic design and analytical construction when building an optimal system. Before developing the system, it is necessary to analyze the factors, the consideration of which will allow achieving the required quality. These factors can be divided into three groups: dynamic characteristics of the elements of the automatic stabilization system; dynamic characteristics of disturbances acting in the system; noise of the meters. From the point of view of dynamic characteristics, the most complex element of the system is the control object, the input of which is the angle of inclination of the washer of the hydraulic pump cylinder block, and the output is the flow of grain mass at the entrance to the threshing machine. From the position of the problem of stabilizing the threshing machine loading, it is necessary to obtain a model of a generalized control object, namely, the dynamic characteristics of the elements of the control object, the dynamic characteristics of the disturbances acting on the control object Each component of the control object is a rather complex mechanism, which is affected by complex stochastic external and internal influences. It is quite difficult to obtain an analytical model of the dynamics of the control object, which, on the one hand, would be simple enough to successfully solve the problems of developing a control system, and on the other hand, would take into account the main factors affecting the quality of the process of stabilizing the flow of grain mass in real operating conditions. Therefore, to solve the problem of stabilizing the flow of grain mass, it is proposed to use the experimental-analytical concept of determining the model of the dynamics of the control object and the disturbances acting on it.
- 26 May 2025
- Published by Central Ukrainian National Technical University in Central Ukrainian Scientific Bulletin. Technical Sciences
- Vol. 2 (11(42))
Analysis of the Control Object for the Development of a System for Automatic Stabilization of the Loading of the Threshing Machine of a Combine Harvester
Oleksandr Didyk, Associate Professor, Candidate of Technical Sciences, Head of the Department of Automation of Production Processes, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, https://orcid.org/0000-0003-1454-0828, e-mail: didyk_s79@ukr.net Oleksandr Serbul, Associate Professor, Candidate of Technical Sciences, Associate Professor of the Department of Automation of Production Processes, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, https://orcid.org/ 0000-0003-1836-5529, e-mail: serbulan@ukr.net Serhiy Teslya, PhD student in Automation, computer-integrated technologies and robotics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0009-0001-7294-2465, e-mail: tesliasv@ukr.net This article provides an analysis of the control object, considers factors that complicate the achievement of maximum quality stabilization of the threshing machine loading, including the dynamic characteristics of the elements of the control object, the dynamic characteristics of the disturbances acting on the control object. To achieve the maximum quality of stabilization of the threshing machine loading of a combine harvester, it is necessary to apply methods of dynamic design and analytical construction when building an optimal system. Before developing the system, it is necessary to analyze the factors, the consideration of which will allow achieving the required quality. These factors can be divided into three groups: dynamic characteristics of the elements of the automatic stabilization system; dynamic characteristics of disturbances acting in the system; noise of the meters. From the point of view of dynamic characteristics, the most complex element of the system is the control object, the input of which is the angle of inclination of the washer of the hydraulic pump cylinder block, and the output is the flow of grain mass at the entrance to the threshing machine. From the position of the problem of stabilizing the threshing machine loading, it is necessary to obtain a model of a generalized control object, namely, the dynamic characteristics of the elements of the control object, the dynamic characteristics of the disturbances acting on the control object Each component of the control object is a rather complex mechanism, which is affected by complex stochastic external and internal influences. It is quite difficult to obtain an analytical model of the dynamics of the control object, which, on the one hand, would be simple enough to successfully solve the problems of developing a control system, and on the other hand, would take into account the main factors affecting the quality of the process of stabilizing the flow of grain mass in real operating conditions. Therefore, to solve the problem of stabilizing the flow of grain mass, it is proposed to use the experimental-analytical concept of determining the model of the dynamics of the control object and the disturbances acting on it.
- 2 August 2024
- Published by Publishing House Helvetica (Publications) in Applied Questions of Mathematical Modeling
- Vol. 7 (1) , 122-135
МАТЕМАТИЧНЕ МОДЕЛЮВАННЯ УМОВ СПРАЦЮВАННЯ СТЕРЖНЕВОГО МОЛОЛЬНОГО ЗАВАНТАЖЕННЯ В КАСКАДНОМУ РЕЖИМІ ПОДРІБНЕННЯ РУДИ
Виокремлено чинники, що впливають на спрацювання молольного завантаження в каскадному режимі подрібнення руди. Серед них – ковзання, удар, перекочування по абразиву, стирання і роздавлювання абразиву, прикладена сила, прикладена швидкість переміщення. Моделювання виконано в межах розроблення теми «Оптимізація продуктивності стержневих млинів розімкнутого циклу по руді і готовому продукту за мінімальних енергетичних і матеріальних перевитрат», яка є складовою частиною наукової тематики Центральноукраїнського національного технічного університету. Тема статті актуальна. Метою роботи є розроблення критерію оцінювання спрацювання стержневого завантаження барабанного млина у вигляді математичної моделі шляхом аналізу дії впливових чинників. Застосовано методи аналізу, порівняння, математичного моделювання, теорії подрібнення руди в стержневих млинах, декомпозиції і композиції, методи теорії стійкості проти спрацювання, методи теорії спрацювання металевих тіл за взаємодії з незакріпленим абразивом. Дослідження проводилися на прикладі стержневого млина МСЦ-35-55, який нині використовують на залізорудних збагачувальних фабриках. Для нього найбільш характерним є каскадний режим роботи, за якого руда руйнується переважно роздавлюванням і стиранням. Використано оптимізоване стержневе завантаження з трьома діаметрами стержнів. У даному режимі роботи стержні найменшого діаметра відтісняються до стінки барабана, а найкрупніші зосереджуються у центральній області його поперечного перерізу. У стержневому млині молольне середовище формується укрупненими зонами зі стержнями наближено однакового діаметра, що дає змогу розглядати його як однорозмірне. Основна маса стержнів, притиснена до стінки барабана нерухомо із захопленою у нижній зоні рудою, переміщується до верхньої позначки, звідки скочується каскадом. Швидкість переміщення молольних тіл на прямій природного укосу стержнів знаходиться в межах 2,12…2,5 м/с. Установлено, що всі діючі чинники на спрацювання молольного середовища впливають на стержні різних діаметрів практично однаково. Тому можливо стверджувати, що стержні різних розмірів у діаметрі працюють практично в однакових умовах. За таких умов основним діючим чинником залишається площа контакту молольного середовища з абразивом у вигляді подрібненої руди, що рекомендовано як критерій оцінювання спрацювання стержнів. Запропоновано критерій оцінювання спрацювання стержневого молольного середовища у вигляді математичної моделі. Перспективою подальших досліджень є імітаційне моделювання спрацювання стержневого молольного завантаження в конкретних типах барабанних млинів.
- 2 August 2024
- Published by Publishing House Helvetica (Publications) in Applied Questions of Mathematical Modeling
- Vol. 7 (1) , 122-135
МАТЕМАТИЧНЕ МОДЕЛЮВАННЯ УМОВ СПРАЦЮВАННЯ СТЕРЖНЕВОГО МОЛОЛЬНОГО ЗАВАНТАЖЕННЯ В КАСКАДНОМУ РЕЖИМІ ПОДРІБНЕННЯ РУДИ
Виокремлено чинники, що впливають на спрацювання молольного завантаження в каскадному режимі подрібнення руди. Серед них – ковзання, удар, перекочування по абразиву, стирання і роздавлювання абразиву, прикладена сила, прикладена швидкість переміщення. Моделювання виконано в межах розроблення теми «Оптимізація продуктивності стержневих млинів розімкнутого циклу по руді і готовому продукту за мінімальних енергетичних і матеріальних перевитрат», яка є складовою частиною наукової тематики Центральноукраїнського національного технічного університету. Тема статті актуальна. Метою роботи є розроблення критерію оцінювання спрацювання стержневого завантаження барабанного млина у вигляді математичної моделі шляхом аналізу дії впливових чинників. Застосовано методи аналізу, порівняння, математичного моделювання, теорії подрібнення руди в стержневих млинах, декомпозиції і композиції, методи теорії стійкості проти спрацювання, методи теорії спрацювання металевих тіл за взаємодії з незакріпленим абразивом. Дослідження проводилися на прикладі стержневого млина МСЦ-35-55, який нині використовують на залізорудних збагачувальних фабриках. Для нього найбільш характерним є каскадний режим роботи, за якого руда руйнується переважно роздавлюванням і стиранням. Використано оптимізоване стержневе завантаження з трьома діаметрами стержнів. У даному режимі роботи стержні найменшого діаметра відтісняються до стінки барабана, а найкрупніші зосереджуються у центральній області його поперечного перерізу. У стержневому млині молольне середовище формується укрупненими зонами зі стержнями наближено однакового діаметра, що дає змогу розглядати його як однорозмірне. Основна маса стержнів, притиснена до стінки барабана нерухомо із захопленою у нижній зоні рудою, переміщується до верхньої позначки, звідки скочується каскадом. Швидкість переміщення молольних тіл на прямій природного укосу стержнів знаходиться в межах 2,12…2,5 м/с. Установлено, що всі діючі чинники на спрацювання молольного середовища впливають на стержні різних діаметрів практично однаково. Тому можливо стверджувати, що стержні різних розмірів у діаметрі працюють практично в однакових умовах. За таких умов основним діючим чинником залишається площа контакту молольного середовища з абразивом у вигляді подрібненої руди, що рекомендовано як критерій оцінювання спрацювання стержнів. Запропоновано критерій оцінювання спрацювання стержневого молольного середовища у вигляді математичної моделі. Перспективою подальших досліджень є імітаційне моделювання спрацювання стержневого молольного завантаження в конкретних типах барабанних млинів.
- 1 February 2024
- Published by National University of Water and Environmental Engineering
The scoop feeder as a means of resource saving in ball mill grinding of feed ore with classifier sands
The subject of the research is a new approach of resource-saving adaptive distributed control of ore grinding with sands of mechanical single-spiral classifier in ball mills on the basis of taking into account the role of scoop feeder, influence on material flows, estimation of technological parameters with increased accuracy and new mathematical models of water dosing in the technological process and algorithm of estimation of solid concentration in the pulp of technological unit. Within the framework of the adopted research methodology a number of methods of different accessory groups have been applied. Comparison method – when studying the statics of the scoop feeder and its operation with one and two gripping bodies. Method of analysis – at increase of resource saving in the process of grinding of raw materials, means and approaches of stabilisation of pulp liquefaction in ball mills, prediction of errors of solid/liquid ratio, inclusion of the initial section of the mill in active work. Method of mathematical modelling – in the development of a mathe-matical model for finding the mass flow rate of solid in the sand flow, finding the water flow rate into the ball mill at various technological points. Method of the theo-ry of algorithmic estimation – in the development of an approach for identification of the solid/liquid ratio in the ball mill. Method of error theory – in measuring pulp volumetric flow rate. Flowmeter theory methods – in measuring the volumetric flow rate of water and slurry. Methods of the theory of scanning devices – at creation of volumetric flow meter of pulp in open flow. The aim of the publication is to investi-gate the scoop feeder as a means of resource saving in a ball mill when grinding ore with classifier sands based on the application of new models of the technological process, a new algorithm for assessing the concentration of solid in the pulp, control of the oscillation of material flows and models of water flow rate stabilisation. The purpose of the research has been achieved. The obtained results are a theoretical basis for the creation of a system of adaptive separate resource-saving control of ore grinding with classifier sands in the first stages of ore preparation.
- 1 February 2024
- Published by National University of Water and Environmental Engineering
The scoop feeder as a means of resource saving in ball mill grinding of feed ore with classifier sands
The subject of the research is a new approach of resource-saving adaptive distributed control of ore grinding with sands of mechanical single-spiral classifier in ball mills on the basis of taking into account the role of scoop feeder, influence on material flows, estimation of technological parameters with increased accuracy and new mathematical models of water dosing in the technological process and algorithm of estimation of solid concentration in the pulp of technological unit. Within the framework of the adopted research methodology a number of methods of different accessory groups have been applied. Comparison method – when studying the statics of the scoop feeder and its operation with one and two gripping bodies. Method of analysis – at increase of resource saving in the process of grinding of raw materials, means and approaches of stabilisation of pulp liquefaction in ball mills, prediction of errors of solid/liquid ratio, inclusion of the initial section of the mill in active work. Method of mathematical modelling – in the development of a mathe-matical model for finding the mass flow rate of solid in the sand flow, finding the water flow rate into the ball mill at various technological points. Method of the theo-ry of algorithmic estimation – in the development of an approach for identification of the solid/liquid ratio in the ball mill. Method of error theory – in measuring pulp volumetric flow rate. Flowmeter theory methods – in measuring the volumetric flow rate of water and slurry. Methods of the theory of scanning devices – at creation of volumetric flow meter of pulp in open flow. The aim of the publication is to investi-gate the scoop feeder as a means of resource saving in a ball mill when grinding ore with classifier sands based on the application of new models of the technological process, a new algorithm for assessing the concentration of solid in the pulp, control of the oscillation of material flows and models of water flow rate stabilisation. The purpose of the research has been achieved. The obtained results are a theoretical basis for the creation of a system of adaptive separate resource-saving control of ore grinding with classifier sands in the first stages of ore preparation.
- Open Access
- 14 December 2023
- Published by Dniprovsk State Technical University in Математичне моделювання
- No. 2(49),p. 76-85
МАТЕМАТИЧНЕ МОДЕЛЮВАННЯ БАЗОВИХ ПАРАМЕТРІВ СТЕРЖНЕВОГО ЗАВАНТАЖЕННЯ ЦИЛІНДРИЧНИХ МЛИНІВ ЯК КЕРОВАНИХ ОБ’ЄКТІВ
Виокремлено параметри стержневого завантаження, ролі яких приділялося мало уваги. Серед них — об’єм пустот для розміщення руди, імпульс ударного стиснення, класифікуюча властивість стержневого завантаження. Дослідження виконані в межах розробки теми «Оптимізація продуктивності стержневих млинів розімкнутого циклу по руді і готовому продукту при мінімальних енергетичних і матеріальних перевитратах», яка є складовою наукової тематики Центральноукраїнського національного технічного університету. Тема статті актуальна. Метою роботи є встановлення базових параметрів стержневого завантаження млинів як керованих об’єктів. Застосовані методи аналізу, порівняння, математичного і геометричного моделювання, методи теорії подрібнення руди в стержневих млинах, композиції, метод імпульсу ударного стиснення, метод кінетики подрібнення руди в млинах. Відмічено, що стержневі млини досягли свого найбільшого розміру (в Україні 4,5×6,0 м), який більше зростати не буде. Для стержневих млинів найбільш сприятливим є каскадний режим роботи, при якому руда руйнується роздавлюванням і стиранням. Використовується багаторозмірне стержньове середовище з 3—4 діаметрами стержнів. У стержневому завантаженні поздовжня сегрегація молольних тіл виникнути не може. Поперечна сегрегація аналогічна кульовому завантаженню. Дрібні стержні відтісняються до стінки барабана, а крупні накопичуються в центральних областях. Витрата стержнів складає 0,12 кг/кВт×г корисно витраченої енергії. Звичайно довантаження стержнів на заміну спрацьованих здійснюють через кожні 5 діб, а перекласифікацію — через кожні 10 діб. Видаляють стержні з барабана млина при спрацюванні до 15—25 мм. Стержневі млини подрібнюють вихідну руду в основному від 25 мм до 2 мм при вмісті твердого в пульпі 84—86 %. Однорозмірні стержні зберігають стійке положення в процесі подрібнення завдяки розпираючому впливу руди між ними. В такому стані в стержневому завантаженні розміщується 21,5 % руди. У кульовому однорозмірному завантаженні цей показник складає 26 %. У стержневих млинах молольне середовище формується обширними зонами з стержнями наближено однакового діаметра, що дозволяє його розглядати як однорозмірне. Його імпульс ударного стиснення складає 14,026, що на 28,3 % вище порівняно з найкращими показниками кульових млинів. Показано, що стержневий млин, виконуючи крупне, середнє і дрібне подрібнення, володіє класифікуючою здатністю. Встановлені параметри стержневого завантаження дозволяють будувати більш ефективні автоматизовані системи керування подрібненням руди в розімкнутих циклах.
- 14 December 2023
- Published by Dniprovsk State Technical University in Математичне моделювання
- No. 2(49),p. 76-85
Open AccessМАТЕМАТИЧНЕ МОДЕЛЮВАННЯ БАЗОВИХ ПАРАМЕТРІВ СТЕРЖНЕВОГО ЗАВАНТАЖЕННЯ ЦИЛІНДРИЧНИХ МЛИНІВ ЯК КЕРОВАНИХ ОБ’ЄКТІВ
Виокремлено параметри стержневого завантаження, ролі яких приділялося мало уваги. Серед них — об’єм пустот для розміщення руди, імпульс ударного стиснення, класифікуюча властивість стержневого завантаження. Дослідження виконані в межах розробки теми «Оптимізація продуктивності стержневих млинів розімкнутого циклу по руді і готовому продукту при мінімальних енергетичних і матеріальних перевитратах», яка є складовою наукової тематики Центральноукраїнського національного технічного університету. Тема статті актуальна. Метою роботи є встановлення базових параметрів стержневого завантаження млинів як керованих об’єктів. Застосовані методи аналізу, порівняння, математичного і геометричного моделювання, методи теорії подрібнення руди в стержневих млинах, композиції, метод імпульсу ударного стиснення, метод кінетики подрібнення руди в млинах. Відмічено, що стержневі млини досягли свого найбільшого розміру (в Україні 4,5×6,0 м), який більше зростати не буде. Для стержневих млинів найбільш сприятливим є каскадний режим роботи, при якому руда руйнується роздавлюванням і стиранням. Використовується багаторозмірне стержньове середовище з 3—4 діаметрами стержнів. У стержневому завантаженні поздовжня сегрегація молольних тіл виникнути не може. Поперечна сегрегація аналогічна кульовому завантаженню. Дрібні стержні відтісняються до стінки барабана, а крупні накопичуються в центральних областях. Витрата стержнів складає 0,12 кг/кВт×г корисно витраченої енергії. Звичайно довантаження стержнів на заміну спрацьованих здійснюють через кожні 5 діб, а перекласифікацію — через кожні 10 діб. Видаляють стержні з барабана млина при спрацюванні до 15—25 мм. Стержневі млини подрібнюють вихідну руду в основному від 25 мм до 2 мм при вмісті твердого в пульпі 84—86 %. Однорозмірні стержні зберігають стійке положення в процесі подрібнення завдяки розпираючому впливу руди між ними. В такому стані в стержневому завантаженні розміщується 21,5 % руди. У кульовому однорозмірному завантаженні цей показник складає 26 %. У стержневих млинах молольне середовище формується обширними зонами з стержнями наближено однакового діаметра, що дозволяє його розглядати як однорозмірне. Його імпульс ударного стиснення складає 14,026, що на 28,3 % вище порівняно з найкращими показниками кульових млинів. Показано, що стержневий млин, виконуючи крупне, середнє і дрібне подрібнення, володіє класифікуючою здатністю. Встановлені параметри стержневого завантаження дозволяють будувати більш ефективні автоматизовані системи керування подрібненням руди в розімкнутих циклах.
- Open Access
- 9 August 2023
- Published by Kherson National Technical University in Вісник Херсонського національного технічного університету
- No. 2(85),p. 37-43
ПОКРАЩЕННЯ ХАРАКТЕРИСТИК КУЛЬОВОГО МЛИНА ЯК КЕРОВАНОГО ОБ’ЄКТА В ПРОЦЕСІ РУДОПІДГОТОВКИ
Внаслідок недостатньо ефективного перемішування матеріалу в початковій частині барабана кульового млина подрібнююче середовище втрачає ефективність роботи, що приводить до перевитрати електричної енергії, куль і футерівки. Дослідженням даного процесу займався ряд авторів в Україні і за кордоном, починаючи з середини 70-х років минулого століття. Запропоновані моделі досліджень, критерій перемішування у вигляді імовірнісного коефіцієнта, який може змінюватися в межах 0…1. Однак нині задачі перемішування матеріалу в кульових млинах до кінця не вирішені. Відсутня загальна оцінка пульсацій матеріалу в барабані, не оцінено стан матеріалу на початковій ділянці і не запропоновано підходів до його покращення. Зрозуміло, що вихід з даної ситуації можливо знайти в удосконаленні кульового млина шляхом покращення його характеристик. Дослідження виконані в межах реалізації теми «Оптимізація продуктивності кульових млинів по руді і готовому продукту при мінімальних енергетичних і матеріальних перевитратах», яка входить до наукової тематики Центральноукраїнського національного технічного університету. З погляду на це тема статті є актуальною. Метою даної роботи є зменшення перевитрат електроенергії, куль і футерівки в процесі подрібнення сировини покращенням характеристик кульового млина удосконаленням завантаження руди, пісків спірального класифікатора та води на основі оцінювання пульсацій матеріалу на початковій ділянці барабана. В процесі досліджень використано метод порівняння, аналізу, методи теорії кульових млинів, теорії автоматичного керування, теорії імовірностей, математичної статистики, теорії випадкових процесів. За допомогою комп’ютерної обробки масиву даних за спеціальною програмою отримані області зміни коливальних параметрів на вході кульового млина по твердому і воді, при яких відносні відхилення маси матеріалу в агрегаті не перевищують ±3,0%, що гарантує нормальний хід технологічного процесу. Встановлено, що як по твердому, так і по воді самими небезпечними є коливання з занадто малою частотою і значними амплітудами. Важливою є проблема перемішування матеріалу в початковій частині барабана кульового млина, оскільки тут низька ефективність осереднення. Найбільш доцільним є шлях, спрямований на покращення умов перемішування ліквідацією існуючих недоліків. По-перше, перед входом руди в млин її необхідно змочити частиною потоку води, а піски перед входом в завитковий живильник максимально розрідити другою частиною потоку води. Третю частину потоку води в млин необхідно розбризкати в широкій зоні входження руди в технологічний агрегат. Такі операції забезпечують ефективне перемішування і подрібнення матеріалу вже в початковій ділянці барабана млина. Збурюючі впливи по потоку руди не порушують технологічний режим кульового млина.
- 9 August 2023
- Published by Kherson National Technical University in Вісник Херсонського національного технічного університету
- No. 2(85),p. 37-43
Open AccessПОКРАЩЕННЯ ХАРАКТЕРИСТИК КУЛЬОВОГО МЛИНА ЯК КЕРОВАНОГО ОБ’ЄКТА В ПРОЦЕСІ РУДОПІДГОТОВКИ
Внаслідок недостатньо ефективного перемішування матеріалу в початковій частині барабана кульового млина подрібнююче середовище втрачає ефективність роботи, що приводить до перевитрати електричної енергії, куль і футерівки. Дослідженням даного процесу займався ряд авторів в Україні і за кордоном, починаючи з середини 70-х років минулого століття. Запропоновані моделі досліджень, критерій перемішування у вигляді імовірнісного коефіцієнта, який може змінюватися в межах 0…1. Однак нині задачі перемішування матеріалу в кульових млинах до кінця не вирішені. Відсутня загальна оцінка пульсацій матеріалу в барабані, не оцінено стан матеріалу на початковій ділянці і не запропоновано підходів до його покращення. Зрозуміло, що вихід з даної ситуації можливо знайти в удосконаленні кульового млина шляхом покращення його характеристик. Дослідження виконані в межах реалізації теми «Оптимізація продуктивності кульових млинів по руді і готовому продукту при мінімальних енергетичних і матеріальних перевитратах», яка входить до наукової тематики Центральноукраїнського національного технічного університету. З погляду на це тема статті є актуальною. Метою даної роботи є зменшення перевитрат електроенергії, куль і футерівки в процесі подрібнення сировини покращенням характеристик кульового млина удосконаленням завантаження руди, пісків спірального класифікатора та води на основі оцінювання пульсацій матеріалу на початковій ділянці барабана. В процесі досліджень використано метод порівняння, аналізу, методи теорії кульових млинів, теорії автоматичного керування, теорії імовірностей, математичної статистики, теорії випадкових процесів. За допомогою комп’ютерної обробки масиву даних за спеціальною програмою отримані області зміни коливальних параметрів на вході кульового млина по твердому і воді, при яких відносні відхилення маси матеріалу в агрегаті не перевищують ±3,0%, що гарантує нормальний хід технологічного процесу. Встановлено, що як по твердому, так і по воді самими небезпечними є коливання з занадто малою частотою і значними амплітудами. Важливою є проблема перемішування матеріалу в початковій частині барабана кульового млина, оскільки тут низька ефективність осереднення. Найбільш доцільним є шлях, спрямований на покращення умов перемішування ліквідацією існуючих недоліків. По-перше, перед входом руди в млин її необхідно змочити частиною потоку води, а піски перед входом в завитковий живильник максимально розрідити другою частиною потоку води. Третю частину потоку води в млин необхідно розбризкати в широкій зоні входження руди в технологічний агрегат. Такі операції забезпечують ефективне перемішування і подрібнення матеріалу вже в початковій ділянці барабана млина. Збурюючі впливи по потоку руди не порушують технологічний режим кульового млина.
- 1 January 2021
- Published by Central Ukrainian National Technical University in National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines
- No. 51
System of Automatic Control for Solid/liquid Ratio in Mills with Circulating Load
Vasily Kondratets, Professor, Doctor in Technics (Doctor of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0002-1411-168Х Oleksandr Serbul, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, e-mail: serbulan@ukr.net, ORCID ID: 0000-0003-1836-5529 Oleksandr Didyk, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0003-1454-0828 Abstract The operation of a ball mill operating in a closed loop with a spiral classifier depends on the vacuum of the pulp in it, which is characterized by a solid / liquid ratio. Supply to the entrance of the ball mill at the same time ore and sand classifier, as well as changes in the circulating load in a wide range greatly complicate the definition of this technological parameter. This situation has led to the fact that the solid / liquid ratio in mills operating in such conditions can not be automatically adjusted, in turn, the deviation of the pulp vacuum from the required value leads to significant losses. The study of the ball mill as a controlled object on the pulp vacuum channel made it possible to describe it using the mathematical expression given in the article. The solution of this expression makes it possible to characterize the change in the mass of the material in the mill over time, provided that a stepwise action is introduced at the entrance - the volume flow of water or ore. A constant value of the mass of material in the mill will clearly characterize the corresponding solid/liquid ratio. It has been found that it is important to study the filtering capabilities of the control object, as control actions on water and disturbing actions on ore can significantly change the vacuum of the pulp in some areas of the mill. The filtering capabilities of the mill can be investigated by its amplitude frequency characteristics, which showed that at low circular frequencies the amplitude frequency characteristics depend on the mode of operation of the mill - the magnitude of the circulating load and the cost of the source ore. Using computer technology, spatial diagrams of the relative oscillations of the mass of material in the mill from the amplitude and frequency of influences at its entrance through the ore and water. In the course of theoretical research it was determined that the only approach to ensure the required accuracy of determining the solid / liquid ratio in these conditions is to filter the signals before applying to the input of the identification unit of the ratio. Thus, the system of automatic control of the solid/liquid ratio at the entrance to the mill is implemented on microprocessor means. Its operation on the laboratory test bench made on the microcontroller showed high accuracy of stabilization of technological parameter, reliability in various conditions of change of characteristics of input signals. Keywords measurement of the solid/liquid ratio, optimization of the choice of measuring instruments Full Text: PDF References 1. Goncharov, Ju.G., Davidkovich, A.S., Gejzenblazen, B.E. & Gulenko, G.V. (1968). Avtomaticheskij kontrol' i regulirovanie tehnologicheskih processov na zhelezorudnyh obogatitel'nyh fabrikah [Automatic control and regulation of technological processes at iron ore processing plants]. Moskow: Nedra [in Russian]. 2. Author's certificate. 388790 USSR, MPK V03V 11/00. Ustrojstvo dlja avtomaticheskogo kontrolja zagruzki i stabilizacii razzhizhenija pul'py v mel'nice [The device for automatic control of loading and stabilization of pulp liquefaction in the mill]. No. 1420849/29-33; stated. March 30, 1970; has been published July 5, 1973, Bul. No. 29. [in Russian]. 3. Pat. 62627, Ukraine, MPK G05D7/01, V03V11/00. Sposib avtomatychnoi stabilizatsii vytrat ridyny [The method of automatic stabilization of fluid flow]. No. 2003043482; stated. April 17, 2003; has been published July 15, 2005, Bul. No. 7. [in Ukrainian]. 4. Pat. 74393, Ukraine, MPK G05D9/02, G05D7/01. Prystrij avtomatychnoi stabilizatsii vytrat ridyny [The device for automatic stabilization of fluid flow]. No. 2003043879; stated. April 25, 2003; has been published December 15, 2005, Bul. No. 12. [in Ukrainian]. 5. Pat. 59644, Ukraine, MPK V03V11/00, V02S25/00. Sposib avtomatychnoi stabilizatsii rozridzhennia pul'py v mlynakh z tsyrkuliuiuchym navantazhenniam [Method of automatic stabilization of pulp rarefaction in mills with circulating load]. No. 2002118758; stated. November 5, 2002; has been published April 15, 2005, Bul. No. 4. [in Ukrainian]. Citations Гончаров Ю.Г., Давидкович А.С., Гейзенблазен Б.Е., Гуленко Г.В. Автоматический контроль и регулирование технологических процессов на железорудных обогатительных фабриках. М.: Недра, 1968. 227 с. Авторское свидетельство СССР № 388790, кл. В 03 В 11/00. Устройство для автоматического контроля загрузки и стабилизации разжижения пульпы в мельнице /Дегтярёв Ф.Н., Мерзляков А.А., Кондратец В.А., Новохатько В.И., Кучма Н.И., Гуленко Т.И. - № 1420849/29-33; заяв. 30.03.1970; опубл. 5.07.1973, Бюл. № 29. Патент України № 62627, G 05 D 7/01, В 03 В 11/00. Спосіб автоматичної стабілізації витрат рідини /Кондратець В.О., Сербул О.М. - № 2003043482; заяв. 17.04.2003; опубл. 15.07.2005, Бюл. № 7. Патент України № 74393, G 05 D 9/02, G 05 D 7/01. Пристрій автоматичної стабілізації витрат рідини /Кондратець В.О., Сербул О.М. - № 2003043879; заяв. 25.04.2003; опубл. 15.12.2005, Бюл. № 12. Патент України № 59644, В 03 В 11/00, В 02 С 25/00. Спосіб автоматичної стабілізації розрідження пульпи в млинах з циркулюючим навантаженням /Кондратець В.О., Сербул О.М. - № 2002118758; заяв. 5.11.2002; опубл. 15.04.2005, Бюл. № 4. Copyright (c) 2021 Vasily Kondratets, Oleksandr Serbul, Oleksandr Didyk
- 1 January 2021
- Published by Central Ukrainian National Technical University in National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines
- No. 51
System of Automatic Control for Solid/liquid Ratio in Mills with Circulating Load
Vasily Kondratets, Professor, Doctor in Technics (Doctor of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0002-1411-168Х Oleksandr Serbul, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, e-mail: serbulan@ukr.net, ORCID ID: 0000-0003-1836-5529 Oleksandr Didyk, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0003-1454-0828 Abstract The operation of a ball mill operating in a closed loop with a spiral classifier depends on the vacuum of the pulp in it, which is characterized by a solid / liquid ratio. Supply to the entrance of the ball mill at the same time ore and sand classifier, as well as changes in the circulating load in a wide range greatly complicate the definition of this technological parameter. This situation has led to the fact that the solid / liquid ratio in mills operating in such conditions can not be automatically adjusted, in turn, the deviation of the pulp vacuum from the required value leads to significant losses. The study of the ball mill as a controlled object on the pulp vacuum channel made it possible to describe it using the mathematical expression given in the article. The solution of this expression makes it possible to characterize the change in the mass of the material in the mill over time, provided that a stepwise action is introduced at the entrance - the volume flow of water or ore. A constant value of the mass of material in the mill will clearly characterize the corresponding solid/liquid ratio. It has been found that it is important to study the filtering capabilities of the control object, as control actions on water and disturbing actions on ore can significantly change the vacuum of the pulp in some areas of the mill. The filtering capabilities of the mill can be investigated by its amplitude frequency characteristics, which showed that at low circular frequencies the amplitude frequency characteristics depend on the mode of operation of the mill - the magnitude of the circulating load and the cost of the source ore. Using computer technology, spatial diagrams of the relative oscillations of the mass of material in the mill from the amplitude and frequency of influences at its entrance through the ore and water. In the course of theoretical research it was determined that the only approach to ensure the required accuracy of determining the solid / liquid ratio in these conditions is to filter the signals before applying to the input of the identification unit of the ratio. Thus, the system of automatic control of the solid/liquid ratio at the entrance to the mill is implemented on microprocessor means. Its operation on the laboratory test bench made on the microcontroller showed high accuracy of stabilization of technological parameter, reliability in various conditions of change of characteristics of input signals. Keywords measurement of the solid/liquid ratio, optimization of the choice of measuring instruments Full Text: PDF References 1. Goncharov, Ju.G., Davidkovich, A.S., Gejzenblazen, B.E. & Gulenko, G.V. (1968). Avtomaticheskij kontrol' i regulirovanie tehnologicheskih processov na zhelezorudnyh obogatitel'nyh fabrikah [Automatic control and regulation of technological processes at iron ore processing plants]. Moskow: Nedra [in Russian]. 2. Author's certificate. 388790 USSR, MPK V03V 11/00. Ustrojstvo dlja avtomaticheskogo kontrolja zagruzki i stabilizacii razzhizhenija pul'py v mel'nice [The device for automatic control of loading and stabilization of pulp liquefaction in the mill]. No. 1420849/29-33; stated. March 30, 1970; has been published July 5, 1973, Bul. No. 29. [in Russian]. 3. Pat. 62627, Ukraine, MPK G05D7/01, V03V11/00. Sposib avtomatychnoi stabilizatsii vytrat ridyny [The method of automatic stabilization of fluid flow]. No. 2003043482; stated. April 17, 2003; has been published July 15, 2005, Bul. No. 7. [in Ukrainian]. 4. Pat. 74393, Ukraine, MPK G05D9/02, G05D7/01. Prystrij avtomatychnoi stabilizatsii vytrat ridyny [The device for automatic stabilization of fluid flow]. No. 2003043879; stated. April 25, 2003; has been published December 15, 2005, Bul. No. 12. [in Ukrainian]. 5. Pat. 59644, Ukraine, MPK V03V11/00, V02S25/00. Sposib avtomatychnoi stabilizatsii rozridzhennia pul'py v mlynakh z tsyrkuliuiuchym navantazhenniam [Method of automatic stabilization of pulp rarefaction in mills with circulating load]. No. 2002118758; stated. November 5, 2002; has been published April 15, 2005, Bul. No. 4. [in Ukrainian]. Citations Гончаров Ю.Г., Давидкович А.С., Гейзенблазен Б.Е., Гуленко Г.В. Автоматический контроль и регулирование технологических процессов на железорудных обогатительных фабриках. М.: Недра, 1968. 227 с. Авторское свидетельство СССР № 388790, кл. В 03 В 11/00. Устройство для автоматического контроля загрузки и стабилизации разжижения пульпы в мельнице /Дегтярёв Ф.Н., Мерзляков А.А., Кондратец В.А., Новохатько В.И., Кучма Н.И., Гуленко Т.И. - № 1420849/29-33; заяв. 30.03.1970; опубл. 5.07.1973, Бюл. № 29. Патент України № 62627, G 05 D 7/01, В 03 В 11/00. Спосіб автоматичної стабілізації витрат рідини /Кондратець В.О., Сербул О.М. - № 2003043482; заяв. 17.04.2003; опубл. 15.07.2005, Бюл. № 7. Патент України № 74393, G 05 D 9/02, G 05 D 7/01. Пристрій автоматичної стабілізації витрат рідини /Кондратець В.О., Сербул О.М. - № 2003043879; заяв. 25.04.2003; опубл. 15.12.2005, Бюл. № 12. Патент України № 59644, В 03 В 11/00, В 02 С 25/00. Спосіб автоматичної стабілізації розрідження пульпи в млинах з циркулюючим навантаженням /Кондратець В.О., Сербул О.М. - № 2002118758; заяв. 5.11.2002; опубл. 15.04.2005, Бюл. № 4. Copyright (c) 2021 Vasily Kondratets, Oleksandr Serbul, Oleksandr Didyk
- 1 January 2021
- Published by Central Ukrainian National Technical University in National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines
- No. 51,p. 210-245
Method of Synthesis of an Optimal Multidimensional Filter for Extracting a Regular Signal Against a Background of Random Noise
С.І. Осадчий, Professor, Doctor in Technics (Doctor of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0002-1811-3594 О.К. Дідик, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, e-mail: didyk_s79@ukr.net, ORCID ID: 0000-0003-1454-0828 О.М. Сербул, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0003-1836-5529 В.М. Каліч, Professor, Doctor in Technics (Doctor of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0002-9907-5496 Abstract In terms of [1] we formulate the problem of synthesis of a complex system of allocation of a useful regular signal. Suppose that a multidimensional stationary filter best processes the input information about the same regular signal r(t), which is obtained by several "non-ideal" meters, and the result is transmitted to the evaluation system. In this article, a multi-channel measurement system, which is connected to the input of a multidimensional data transmission system, the dynamics of which is described by a system of linear differential equations. The input of the measuring system receives an n-dimensional vector of measured signals r (t), the components of which are deterministic functions. The vector r (t) belongs to the main group of "non-ideal" meters. Measurements are accompanied by interference, which is a random stationary process with zero mathematical expectation and a known fractional-rational matrix of spectral densities. An integral indicator of the quality of the system is the sum of the weighted integral quadratic error of the regular signal estimation and the variance of the random component of the error. Thus, a new algorithm for the synthesis of a complete optimal regular signal extraction system against the background of a multidimensional stationary random interference is obtained, which allows to find the structure and parameters of a multidimensional optimal filter taking into account the dynamics of the information transmission system. Keywords measurement, filtering, signal, noise, random process, synthesis method Full Text: PDF References 1. Blohin, L.N. (1982). Optimalnye sistemy stabilizatsii [Optimal stabilization systems]. Kyiv: Tehnika [in Russian]. 2. Azarskov, V.N., Blohin L.N. et al (2004). Robastnye metody otsenivaniia identifikatsii i adaptivnogo upravleniia [Robust estimation methods for identification and adaptive control]. Kyiv: NAU [in Russian]. 3. Blohin, L.N., Osadchiy, S.I., Didyk, A.K. & Rudiuk, G.I. (2015). Tehnologii konstuirovaniia sovremennyh konkurentnosposobnyh kompleksov upravleniia stohasticheskim dvizheniem obektov [Technologies for designing modern competitive control systems for stochastic movement of objects]. Kirovograd: Lysenko V.F. [in Russian]. 4. Blohin, L.N. & Burychenko, M.U. (2003). Statystychna dynamika system ypravlinnia [Statistical dynamics of control systems]. Kyiv: NAU [in Ukrainian]. Citations Блохин Л.Н. Оптимальные системы стабилизации. К.: Техника, 1982. 144 с. Азарсков В.Н., Блохин Л.Н. и др. Робастные методы оценивания идентификации и адаптивного управления. К.: НАУ, 2004. 500 с. Технологии конструирования современных конкурентоспособных комплексов управления стохастическим движением объектов: монография / Л.Н. Блохин, С.И. Осадчий, А.К. Дидык, Г.И. Рудюк. Кировоград: Лисенко В.Ф., 2015. 284 с. Блохін Л.М., Буриченко М.Ю. Статистична динаміка систем управління: підручник. К.: НАУ, 2003. 208 с. Copyright (c) 2021 Serhii Osadchiy, Oleksandr Didyk, Oleksandr Serbul, Viktor Kalich
- 1 January 2021
- Published by Central Ukrainian National Technical University in National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines
- No. 51,p. 210-245
Method of Synthesis of an Optimal Multidimensional Filter for Extracting a Regular Signal Against a Background of Random Noise
С.І. Осадчий, Professor, Doctor in Technics (Doctor of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0002-1811-3594 О.К. Дідик, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, e-mail: didyk_s79@ukr.net, ORCID ID: 0000-0003-1454-0828 О.М. Сербул, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0003-1836-5529 В.М. Каліч, Professor, Doctor in Technics (Doctor of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0002-9907-5496 Abstract In terms of [1] we formulate the problem of synthesis of a complex system of allocation of a useful regular signal. Suppose that a multidimensional stationary filter best processes the input information about the same regular signal r(t), which is obtained by several "non-ideal" meters, and the result is transmitted to the evaluation system. In this article, a multi-channel measurement system, which is connected to the input of a multidimensional data transmission system, the dynamics of which is described by a system of linear differential equations. The input of the measuring system receives an n-dimensional vector of measured signals r (t), the components of which are deterministic functions. The vector r (t) belongs to the main group of "non-ideal" meters. Measurements are accompanied by interference, which is a random stationary process with zero mathematical expectation and a known fractional-rational matrix of spectral densities. An integral indicator of the quality of the system is the sum of the weighted integral quadratic error of the regular signal estimation and the variance of the random component of the error. Thus, a new algorithm for the synthesis of a complete optimal regular signal extraction system against the background of a multidimensional stationary random interference is obtained, which allows to find the structure and parameters of a multidimensional optimal filter taking into account the dynamics of the information transmission system. Keywords measurement, filtering, signal, noise, random process, synthesis method Full Text: PDF References 1. Blohin, L.N. (1982). Optimalnye sistemy stabilizatsii [Optimal stabilization systems]. Kyiv: Tehnika [in Russian]. 2. Azarskov, V.N., Blohin L.N. et al (2004). Robastnye metody otsenivaniia identifikatsii i adaptivnogo upravleniia [Robust estimation methods for identification and adaptive control]. Kyiv: NAU [in Russian]. 3. Blohin, L.N., Osadchiy, S.I., Didyk, A.K. & Rudiuk, G.I. (2015). Tehnologii konstuirovaniia sovremennyh konkurentnosposobnyh kompleksov upravleniia stohasticheskim dvizheniem obektov [Technologies for designing modern competitive control systems for stochastic movement of objects]. Kirovograd: Lysenko V.F. [in Russian]. 4. Blohin, L.N. & Burychenko, M.U. (2003). Statystychna dynamika system ypravlinnia [Statistical dynamics of control systems]. Kyiv: NAU [in Ukrainian]. Citations Блохин Л.Н. Оптимальные системы стабилизации. К.: Техника, 1982. 144 с. Азарсков В.Н., Блохин Л.Н. и др. Робастные методы оценивания идентификации и адаптивного управления. К.: НАУ, 2004. 500 с. Технологии конструирования современных конкурентоспособных комплексов управления стохастическим движением объектов: монография / Л.Н. Блохин, С.И. Осадчий, А.К. Дидык, Г.И. Рудюк. Кировоград: Лисенко В.Ф., 2015. 284 с. Блохін Л.М., Буриченко М.Ю. Статистична динаміка систем управління: підручник. К.: НАУ, 2003. 208 с. Copyright (c) 2021 Serhii Osadchiy, Oleksandr Didyk, Oleksandr Serbul, Viktor Kalich