Anton Nosenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Anton Nosenko has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Taras Mika
G.V. Kurdyumov Institute for Metal Physics of National Academy of Sciences of Ukraine, 36, Academician Vernadsky Boulevard, Kyiv, 03142, Ukraine
4 shared publications - Michał Nowicki
Vilnius Gediminas Technical University
3 shared publications - Olexandr Rudenko
G.V. Kurdyumov Institute for Metal Physics of National Academy of Sciences of Ukraine, 6, Academician Vernadsky Boulevard, Kyiv, 03142, Ukraine.
3 shared publications - Roman Szewczyk
Systems Research Institute Polish Academy of Sciences
3 shared publications - Andriy Marusenkov
Lviv Center of the Institute of Space Research, 79060 Lviv, Ukraine
2 shared publications - Myroslava Tashak
Lviv Polytechnic National University, Lviv, Ukraine
2 shared publications
Latest Publications
- 10 September 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 62 (4) , 114-120
Influence of an acidic medium on the passivation processes of a cobalt-based amorphous alloy
The investigated Co80.85Fe4.17Mn3.69Si5.81B5.48 ribbon amorphous alloy exhibited significantly higher corrosion resistance in 0.1 M HNO3 solution than in 0.1 M H2SO4. The oxidizing properties of nitrate ions promote the formation of a stable protective oxide layer. In nitric acid, surface passivation is observed, with corrosion current densities decreasing to 0.12–0.47 mkA/cm2. In sulfuric acid, the processes are less stable due to the continuous fracture and restoration of the passive film. The contact surface of the amorphous metal alloy ribbon is characterized by higher corrosion resistance compared to the external surface Electrochemical parameters prove the effectiveness of silicon and magnesium alloying to form stable passive films and demonstrate the prospective use of this alloy in machine-building, chemical industry and biomedicine.
- 10 September 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 62 (4) , 114-120
Influence of an acidic medium on the passivation processes of a cobalt-based amorphous alloy
The investigated Co80.85Fe4.17Mn3.69Si5.81B5.48 ribbon amorphous alloy exhibited significantly higher corrosion resistance in 0.1 M HNO3 solution than in 0.1 M H2SO4. The oxidizing properties of nitrate ions promote the formation of a stable protective oxide layer. In nitric acid, surface passivation is observed, with corrosion current densities decreasing to 0.12–0.47 mkA/cm2. In sulfuric acid, the processes are less stable due to the continuous fracture and restoration of the passive film. The contact surface of the amorphous metal alloy ribbon is characterized by higher corrosion resistance compared to the external surface Electrochemical parameters prove the effectiveness of silicon and magnesium alloying to form stable passive films and demonstrate the prospective use of this alloy in machine-building, chemical industry and biomedicine.
- 29 May 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 62 (2) , 32-39
Electrochemical properties of thermomodified cobalt amorphic alloys in alkaline media
The effect of non-isothermal heating and chemical modification on the structural state and corrosion resistance of amorphous Co72Fe5Si11B12 and Co70Fe2.5Cr4.5Si11B12 cobalt alloys in 1 M aqueous potassium hydroxide solution is investigated. During heating of the Co72Fe5Si11B12 alloy, significant surface changes occur, in particular the formation of crystalline phases and oxidation, which is accompanied by a decrease in the rate of corrosion pro¬cesses. Heat treatment at temperatures of 773–787 K helps to increase the corrosion resistance of the material in an alkaline environment. It is found that the amorphous Co70Fe2.5Cr4.5Si11B12 alloy is characterized by higher corrosion resistance compared to the alloy without chromium addition. Thermal modification of the alloy with Cr content causes a shift of corrosion potentials in the positive direction, however it is accompa¬nied by an increase in corrosion currents. It is found that increase in the potential sweep rate does not significantly affect the values of corrosion potentials, but leads to an increase in corrosion currents in contact with an aggressive environment.
- 29 May 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 62 (2) , 32-39
Electrochemical properties of thermomodified cobalt amorphic alloys in alkaline media
The effect of non-isothermal heating and chemical modification on the structural state and corrosion resistance of amorphous Co72Fe5Si11B12 and Co70Fe2.5Cr4.5Si11B12 cobalt alloys in 1 M aqueous potassium hydroxide solution is investigated. During heating of the Co72Fe5Si11B12 alloy, significant surface changes occur, in particular the formation of crystalline phases and oxidation, which is accompanied by a decrease in the rate of corrosion pro¬cesses. Heat treatment at temperatures of 773–787 K helps to increase the corrosion resistance of the material in an alkaline environment. It is found that the amorphous Co70Fe2.5Cr4.5Si11B12 alloy is characterized by higher corrosion resistance compared to the alloy without chromium addition. Thermal modification of the alloy with Cr content causes a shift of corrosion potentials in the positive direction, however it is accompa¬nied by an increase in corrosion currents. It is found that increase in the potential sweep rate does not significantly affect the values of corrosion potentials, but leads to an increase in corrosion currents in contact with an aggressive environment.
- 1 November 2019
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Ukrainian Journal of Physics
- Vol. 64 (10) , 942
Resonance Properties and Magnetic Anisotropy of Nanocrystalline Fe73Cu1Nb3Si16B7 Alloy
Resonance properties of nanocrystalline ribbons of Fe73Cu1Nb3Si16B7 alloy annealed with the use of an electric current under a tensile stress of 180 MPa have been studied within the ferromagnetic resonance method. Two kinds of ferromagnetic regions with different anisotropic behaviors that coexist in the alloy after the annealing are detected. One of them is amorphous and weakly magnetically anisotropic, whereas the other is characterized by a pronounced uniaxial magnetic anisotropy and corresponds to the nanocrystalline phase. Quantitative estimations of magnetic parameters in two magnetic phases of the alloy are made.
- 1 November 2019
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Ukrainian Journal of Physics
- Vol. 64 (10) , 942
Resonance Properties and Magnetic Anisotropy of Nanocrystalline Fe73Cu1Nb3Si16B7 Alloy
Resonance properties of nanocrystalline ribbons of Fe73Cu1Nb3Si16B7 alloy annealed with the use of an electric current under a tensile stress of 180 MPa have been studied within the ferromagnetic resonance method. Two kinds of ferromagnetic regions with different anisotropic behaviors that coexist in the alloy after the annealing are detected. One of them is amorphous and weakly magnetically anisotropic, whereas the other is characterized by a pronounced uniaxial magnetic anisotropy and corresponds to the nanocrystalline phase. Quantitative estimations of magnetic parameters in two magnetic phases of the alloy are made.
- Open Access
Strain Dependence of Hysteretic Giant Magnetoimpedance Effect in Co-Based Amorphous Ribbon
The significant strain dependence of the hysteretic Giant Magnetoimpedance (GMI) effect in a Co67Fe3Cr3B12Si15 amorphous alloy in a low magnetizing field is presented. A simplistic test stand capable of continuous measurements of GMI characteristics under the influence of strain is detailed. Based on the results, a stress-impedance (SI) sensor is proposed, with a gauge factor similar to semiconductor strain gauges but more robust. An effective method of minimizing external magnetic field influence on the SI effect is given.
Open AccessStrain Dependence of Hysteretic Giant Magnetoimpedance Effect in Co-Based Amorphous Ribbon
The significant strain dependence of the hysteretic Giant Magnetoimpedance (GMI) effect in a Co67Fe3Cr3B12Si15 amorphous alloy in a low magnetizing field is presented. A simplistic test stand capable of continuous measurements of GMI characteristics under the influence of strain is detailed. Based on the results, a stress-impedance (SI) sensor is proposed, with a gauge factor similar to semiconductor strain gauges but more robust. An effective method of minimizing external magnetic field influence on the SI effect is given.
- 1 December 2018
- Published by PIAP - Industrial Research Institute for Automation and Measurements in Journal of Automation, Mobile Robotics and Intelligent Systems
- Vol. 12 (3) , 40-42
Mobile Ferrograph System for Ultrahigh Permeability Alloys
- 1 December 2018
- Published by PIAP - Industrial Research Institute for Automation and Measurements in Journal of Automation, Mobile Robotics and Intelligent Systems
- Vol. 12 (3) , 40-42
Mobile Ferrograph System for Ultrahigh Permeability Alloys
- Open Access
Modeling the Hysteresis Loop of Ultra-High Permeability Amorphous Alloy for Space Applications
This paper presents investigation results regarding the Jiles-Atherton-based hysteresis loop modeling of ultra-high permeability amorphous alloy MELTA® MM-5Co. The measurement stand is capable of accurately measuring minor and major hysteresis loops for such a material together with exemplary measurement results. The main source of the measurement error is highlighted, which includes the Earth’s field influence. The results of hysteresis loop modeling with the original Jiles-Atherton model and with two of its modifications are given. In all cases, the parameters of the Jiles-Atherton model were identified in two-step identification on the basis of a differential evolution optimization algorithm. The results indicate that both the original and modified Jiles-Atherton models are suitable for modeling the ultra-soft amorphous alloy. However, the hysteresis model’s parameters vary significantly.
Open AccessModeling the Hysteresis Loop of Ultra-High Permeability Amorphous Alloy for Space Applications
This paper presents investigation results regarding the Jiles-Atherton-based hysteresis loop modeling of ultra-high permeability amorphous alloy MELTA® MM-5Co. The measurement stand is capable of accurately measuring minor and major hysteresis loops for such a material together with exemplary measurement results. The main source of the measurement error is highlighted, which includes the Earth’s field influence. The results of hysteresis loop modeling with the original Jiles-Atherton model and with two of its modifications are given. In all cases, the parameters of the Jiles-Atherton model were identified in two-step identification on the basis of a differential evolution optimization algorithm. The results indicate that both the original and modified Jiles-Atherton models are suitable for modeling the ultra-soft amorphous alloy. However, the hysteresis model’s parameters vary significantly.
- 21 November 2017
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metallofizika i Noveishie Tekhnologii
- Vol. 39 (5) , 645-655
Properties of the Soft-Magnetic Nanocrystalline Fe–B–P–Nb–Cr Alloys with a High Saturation Induction
- 21 November 2017
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metallofizika i Noveishie Tekhnologii
- Vol. 39 (5) , 645-655
Properties of the Soft-Magnetic Nanocrystalline Fe–B–P–Nb–Cr Alloys with a High Saturation Induction
- Open Access
- 26 April 2017
- Published by Springer Nature in Discover Nano
- Vol. 12 (1) , 299
Effect of Mechanical Stresses in Rapidly Heated Fe73Cu1Nb3Si16B7 Ribbon Arising During the Ring Core Formation on Their Magnetic Properties
The influence of winding-induced mechanical stresses on the magnetic anisotropy and core loss in toroidal cores made of Fe73Cu1Nb3Si16B7 ribbon is studied. The ribbon for the cores was rapidly pre-heated under tensile stress up to 120 MPa. It was found that magnetic characteristics of the material (magnetic anisotropy energy and the core loss) can be controlled by varying the tensile stress during the preliminary rapid heating of the ribbon. It was shown that with reducing core diameter, the magnetic anisotropy energy and core loss significantly increase. However, relatively high winding-induced core loss in small cores can be significantly reduced by increasing tensile stresses applied to the ribbon during pre-heating.
- 26 April 2017
- Published by Springer Nature in Discover Nano
- Vol. 12 (1) , 299
Open AccessEffect of Mechanical Stresses in Rapidly Heated Fe73Cu1Nb3Si16B7 Ribbon Arising During the Ring Core Formation on Their Magnetic Properties
The influence of winding-induced mechanical stresses on the magnetic anisotropy and core loss in toroidal cores made of Fe73Cu1Nb3Si16B7 ribbon is studied. The ribbon for the cores was rapidly pre-heated under tensile stress up to 120 MPa. It was found that magnetic characteristics of the material (magnetic anisotropy energy and the core loss) can be controlled by varying the tensile stress during the preliminary rapid heating of the ribbon. It was shown that with reducing core diameter, the magnetic anisotropy energy and core loss significantly increase. However, relatively high winding-induced core loss in small cores can be significantly reduced by increasing tensile stresses applied to the ribbon during pre-heating.
- Open Access
- 5 February 2016
- Published by Springer Nature in Discover Nano
- Vol. 11 (1) , 1-7
DC bias immune nanocrystalline magnetic cores made of Fe73Nb3Cu1B7Si16 ribbon with induced transverse magnetic anisotropy
The comparative analysis of magnetic properties of cut cores made of nanocrystalline Fe73Nb3Cu1B7Si16 alloy ribbon and cores made of the same ribbon with preliminary tension-induced transverse magnetic anisotropy was carried out. The possibility of improving magnetic properties of cut cores, decreasing loss, and increasing DC bias immunity of reversible magnetic permeability is presented. The influence of induced magnetic anisotropy on DC bias immunity of reversible magnetic permeability was investigated. The advantages and disadvantages of new cores (made of ribbon heated under tensile stress) over cut ones were determined.
- 5 February 2016
- Published by Springer Nature in Discover Nano
- Vol. 11 (1) , 1-7
Open AccessDC bias immune nanocrystalline magnetic cores made of Fe73Nb3Cu1B7Si16 ribbon with induced transverse magnetic anisotropy
The comparative analysis of magnetic properties of cut cores made of nanocrystalline Fe73Nb3Cu1B7Si16 alloy ribbon and cores made of the same ribbon with preliminary tension-induced transverse magnetic anisotropy was carried out. The possibility of improving magnetic properties of cut cores, decreasing loss, and increasing DC bias immunity of reversible magnetic permeability is presented. The influence of induced magnetic anisotropy on DC bias immunity of reversible magnetic permeability was investigated. The advantages and disadvantages of new cores (made of ribbon heated under tensile stress) over cut ones were determined.
- 1 January 2016
- Published by Walter de Gruyter GmbH
Soft magnetic properties of nanocrystalline Fe73B7Si16Nb3Cu1 alloy after rapid heating under tensile stress
Amorphous Fe73B7Si16Nb3Cu1 ribbon was crystallized rapidly by electric current heating under simultaneously applied tensile stress along the ribbon axis. As a result, strong transverse magnetic anisotropy was induced in the ribbon. Dynamic magnetic properties of the ribbons rapidly heated either under the tensile stress or without tensile stress were measured using toroidal cores. Optimal electric current heating regime that provides maximum improvement of the initial magnetic permeability and core loss was determined. Tensile stress increase from 0 to 180 MPa was shown to result in the decrease of the initial magnetic permeability down to 400 and core loss at frequencies from 0.4 to 200 kHz. Comparative analysis of magnetic properties of the cut core (with non-magnetic gap) and the cores heated under tensile stress was carried out. The magnetic properties of the latter cores are advantageous for manufacturing the reactors and linear chokes of switch-mode power supplies.
- 1 January 2016
- Published by Walter de Gruyter GmbH
Soft magnetic properties of nanocrystalline Fe73B7Si16Nb3Cu1 alloy after rapid heating under tensile stress
Amorphous Fe73B7Si16Nb3Cu1 ribbon was crystallized rapidly by electric current heating under simultaneously applied tensile stress along the ribbon axis. As a result, strong transverse magnetic anisotropy was induced in the ribbon. Dynamic magnetic properties of the ribbons rapidly heated either under the tensile stress or without tensile stress were measured using toroidal cores. Optimal electric current heating regime that provides maximum improvement of the initial magnetic permeability and core loss was determined. Tensile stress increase from 0 to 180 MPa was shown to result in the decrease of the initial magnetic permeability down to 400 and core loss at frequencies from 0.4 to 200 kHz. Comparative analysis of magnetic properties of the cut core (with non-magnetic gap) and the cores heated under tensile stress was carried out. The magnetic properties of the latter cores are advantageous for manufacturing the reactors and linear chokes of switch-mode power supplies.