Laddu Indika Nalin De Silva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Laddu Indika Nalin De Silva has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Junichi Koseki
2 shared publicationsTakeshi Sato
2 shared publicationsA. M. D. C. Bandara
Faculty of Engineering, University of Moratuwa, Colombo, Sri Lanka
1 shared publication- A. M. D. C. Bandara
University of Moratuwa
1 shared publication A.M.D.C. Bandara
Faculty of Engineering, University of Moratuwa, Moratuwa, Sri Lanka
1 shared publicationC. Sanjei
Department of Civil engineering, University of Moratuwa, Colombo, Sri Lanka
1 shared publication
Latest Publications
- 23 October 2024
- Published by Springer Nature
- p. 13-21
Finite Element Analysis on the Distribution of Stress Through Layered Soils
- 23 October 2024
- Published by Springer Nature
- p. 13-21
Finite Element Analysis on the Distribution of Stress Through Layered Soils
- 31 December 2022
- Published by Sri Lanka Journals Online in Engineer: Journal of the Institution of Engineers, Sri Lanka
- Vol. 55 (4) , 9-15
Effect of Bentonite and Polymer Drilling Fluids on Skin Friction of Bored Piles
- 31 December 2022
- Published by Sri Lanka Journals Online in Engineer: Journal of the Institution of Engineers, Sri Lanka
- Vol. 55 (4) , 9-15
Effect of Bentonite and Polymer Drilling Fluids on Skin Friction of Bored Piles
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 651-655
An Experimental Investigation on Shaft Resistance of Cast In-Situ Bored Piles in Intact Rock
Pile foundations socketed into rock are used to transfer the loads from the large structures to the underlying bedrock when the surface soils are unable to provide the adequate bearing capacity. The bearing capacity of the pile foundation depends on the base resistance and the shaft resistance given by the underlying rock. The shaft resistance of the rock socketed pile is a very sensitive parameter and governed by several parameters including the mechanical properties of the surrounding rock, rock mass classification, pile diameter, roughness of rock – concrete interface, discontinuities of the rock, the radial force induced by the load applied on the pile and the rock types. The performance of rock-socketed piles at serviceability limit mainly depends on the shaft resistance induced at the rock – concrete interface. The shaft resistance should be estimated accurately for safe and economic design of the structure. This research is focused on the experimental investigation on shaft resistance of cast in situ bored piles in intact rock. The samples were prepared to get the concrete – rock interface and tests were conducted in the laboratory for different types of rock using tri-axial apparatus and unconfined compressive strength apparatus. The ultimate shaft resistance was calculated from the experimental results for different rocks commonly found in Sri Lanka. Biotite hornblende gneiss, marble rock and charnokitic hornblende gneiss are the types of rock used in this study. From the gradient of shear stress –shear strain graph, shear modulus of the interface was evaluated. It was found that these rocks have ultimate shaft resistance in the range of 3.5 - 4.5 MPa and Shear modulus to be in the range of 60 – 70 MPa. Confining stresses in the range of 0 kPa to 400 kPa do not seem to have any effect on the shaft resistance.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 651-655
An Experimental Investigation on Shaft Resistance of Cast In-Situ Bored Piles in Intact Rock
Pile foundations socketed into rock are used to transfer the loads from the large structures to the underlying bedrock when the surface soils are unable to provide the adequate bearing capacity. The bearing capacity of the pile foundation depends on the base resistance and the shaft resistance given by the underlying rock. The shaft resistance of the rock socketed pile is a very sensitive parameter and governed by several parameters including the mechanical properties of the surrounding rock, rock mass classification, pile diameter, roughness of rock – concrete interface, discontinuities of the rock, the radial force induced by the load applied on the pile and the rock types. The performance of rock-socketed piles at serviceability limit mainly depends on the shaft resistance induced at the rock – concrete interface. The shaft resistance should be estimated accurately for safe and economic design of the structure. This research is focused on the experimental investigation on shaft resistance of cast in situ bored piles in intact rock. The samples were prepared to get the concrete – rock interface and tests were conducted in the laboratory for different types of rock using tri-axial apparatus and unconfined compressive strength apparatus. The ultimate shaft resistance was calculated from the experimental results for different rocks commonly found in Sri Lanka. Biotite hornblende gneiss, marble rock and charnokitic hornblende gneiss are the types of rock used in this study. From the gradient of shear stress –shear strain graph, shear modulus of the interface was evaluated. It was found that these rocks have ultimate shaft resistance in the range of 3.5 - 4.5 MPa and Shear modulus to be in the range of 60 – 70 MPa. Confining stresses in the range of 0 kPa to 400 kPa do not seem to have any effect on the shaft resistance.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 644-650
Analysis of Stability Enhancement of Soldier Pile Retaining Wall
In construction industry, Soldier pile retaining wall with timber laggings is one of the most common retaining walls. It is relatively fastest and cheapest method. Stability of the soldier pile retaining wall is the main consideration during the design and construction period. To predict the lateral wall deformation for excavations, it is important to perform a numerical analysis, because the deflection of the soldier pile retaining wall is critical in practice. In the present study, theoretical analysis and numerical analysis were carried out to analyze the stability of the soldier pile retaining wall with the presence of surcharge. This research mainly focusing on the stability enhancement of the soldier pile retaining wall considering the factors such as, depth of embedment of the steel H-sections, spacing between steel H-sections, width of the steel H-section and soil parameters. Also, this paper presents the results of theoretical study using limit equilibrium method to assess the stability of the wall by considering the factor of safety. And, two-dimensional finite element model (FEM) of soldier pile retaining wall with horizontal timber laggings was created in Plaxis 2D software to estimate the lateral displacement of the wall and bending moment capacity.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 644-650
Analysis of Stability Enhancement of Soldier Pile Retaining Wall
In construction industry, Soldier pile retaining wall with timber laggings is one of the most common retaining walls. It is relatively fastest and cheapest method. Stability of the soldier pile retaining wall is the main consideration during the design and construction period. To predict the lateral wall deformation for excavations, it is important to perform a numerical analysis, because the deflection of the soldier pile retaining wall is critical in practice. In the present study, theoretical analysis and numerical analysis were carried out to analyze the stability of the soldier pile retaining wall with the presence of surcharge. This research mainly focusing on the stability enhancement of the soldier pile retaining wall considering the factors such as, depth of embedment of the steel H-sections, spacing between steel H-sections, width of the steel H-section and soil parameters. Also, this paper presents the results of theoretical study using limit equilibrium method to assess the stability of the wall by considering the factor of safety. And, two-dimensional finite element model (FEM) of soldier pile retaining wall with horizontal timber laggings was created in Plaxis 2D software to estimate the lateral displacement of the wall and bending moment capacity.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 394-399
Study on Development of Arching Action of Sand Using an Earth Pressure Cell
Stress transformation from yielding part of soil on to adjacent rigid part is known as the arching action of soil. Terzaghi’s trapdoor test was an important milestone in development of theories on soil arching, soil arching has both active and passive effects. Stresses acting on underground structures need to be estimated correctly for economical design and evaluation of the performance of those structures accounting the effect of soil arching. An experimental approach in measuring real-time stress variation on buried structures due to arching effect of soil is discussed in this paper. Experimental study was done to study the effect of both active and passive soil arching in dry and saturated sandy soil using effective and total earth pressure cells and the stress variation on underground structures was analyzed. The test results were compared with Terzaghi’s arching theory. Results conclude that in passive soil arching stress transform to structures increase with stress increment where, s the stress transform to structures reduce with settlement of the structure. In addition, settling of surrounding soil causes increase in the stress transform to structures.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 394-399
Study on Development of Arching Action of Sand Using an Earth Pressure Cell
Stress transformation from yielding part of soil on to adjacent rigid part is known as the arching action of soil. Terzaghi’s trapdoor test was an important milestone in development of theories on soil arching, soil arching has both active and passive effects. Stresses acting on underground structures need to be estimated correctly for economical design and evaluation of the performance of those structures accounting the effect of soil arching. An experimental approach in measuring real-time stress variation on buried structures due to arching effect of soil is discussed in this paper. Experimental study was done to study the effect of both active and passive soil arching in dry and saturated sandy soil using effective and total earth pressure cells and the stress variation on underground structures was analyzed. The test results were compared with Terzaghi’s arching theory. Results conclude that in passive soil arching stress transform to structures increase with stress increment where, s the stress transform to structures reduce with settlement of the structure. In addition, settling of surrounding soil causes increase in the stress transform to structures.
- 1 December 2018
- Published by Springer Nature
- p. 228-238
Development of a 1-DoF Force Sensor with an Aluminum Cross-Beam Structure for Earth Pressure Measurement System
- 1 December 2018
- Published by Springer Nature
- p. 228-238
Development of a 1-DoF Force Sensor with an Aluminum Cross-Beam Structure for Earth Pressure Measurement System
- 1 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 4, 527-532
Development of an Earth Pressure Cell to Evaluate the Total and Effective Stresses of Soil
This study focuses on development of an earth pressure cell to identify the effective soil pressure and pore water pressure in a single degree of freedom sensor system. A strain gauge based four cross-beam metal structural element is used to identify the maximum earth pressure of 150 kN/m 2 . For that, pressure transferring mechanisms are developed to transfer the earth loads to sensing elements via deformation of cross-beam structure as a total load and as an effective load. Finite element analysis is done to select the optimum dimension for the sensor element. Other dimensions and the shape of the sensor are selected by referring the literature. Accuracy of the system will be verified by using methods which are currently available for measuring soil pressure and pore water pressure under laboratory and field conditions.
- 1 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 4, 527-532
Development of an Earth Pressure Cell to Evaluate the Total and Effective Stresses of Soil
This study focuses on development of an earth pressure cell to identify the effective soil pressure and pore water pressure in a single degree of freedom sensor system. A strain gauge based four cross-beam metal structural element is used to identify the maximum earth pressure of 150 kN/m 2 . For that, pressure transferring mechanisms are developed to transfer the earth loads to sensing elements via deformation of cross-beam structure as a total load and as an effective load. Finite element analysis is done to select the optimum dimension for the sensor element. Other dimensions and the shape of the sensor are selected by referring the literature. Accuracy of the system will be verified by using methods which are currently available for measuring soil pressure and pore water pressure under laboratory and field conditions.
- Open Access
- 1 January 2018
- Published by College Publishing in Journal of Green Building
- Vol. 13 (1) , 56-72
SEMI-TIERED HOUSING FOR LATERITE EARTH SLOPING LANDS—A SUSTAINABLE SOLUTION WITH ALTERNATIVE MATERIALS AND METHODS
Increased demand for affordable housing and the limited availability of flat terrain for its construction are two major problems facing the provision of houses of acceptable quality in many countries around the world. There is limited research integrating the utilization of a stepped approach to sloping terrain with appropriate housing models to minimize slope instability potential. This paper introduces a new semi-tiered housing model where the footprint of the house is located on tiers prepared with short vertical cuts of 1.5–2m. Such vertical cuts are found to be stable with laterite soil which is a commonly available type of soil in the tropics. The excess soil generated from cut material was transformed into cement stabilized rammed earth, which is a cost effective material with low embodied energy. This is an ideal candidate for the construction of retaining walls and foundations, and such applications are demonstrated with adequate details. Further, many other types of sustainable building materials are highlighted with a case study of this housing model in a scheme of 13 housing units in Sri Lanka. The attention to detail required in construction and the applicability of alternative building materials and methods to improve the sustainability of such houses have been discussed in detail. These semi-tiered houses have the potential to address many of the current construction challenges.
- 1 January 2018
- Published by College Publishing in Journal of Green Building
- Vol. 13 (1) , 56-72
Open AccessSEMI-TIERED HOUSING FOR LATERITE EARTH SLOPING LANDS—A SUSTAINABLE SOLUTION WITH ALTERNATIVE MATERIALS AND METHODS
Increased demand for affordable housing and the limited availability of flat terrain for its construction are two major problems facing the provision of houses of acceptable quality in many countries around the world. There is limited research integrating the utilization of a stepped approach to sloping terrain with appropriate housing models to minimize slope instability potential. This paper introduces a new semi-tiered housing model where the footprint of the house is located on tiers prepared with short vertical cuts of 1.5–2m. Such vertical cuts are found to be stable with laterite soil which is a commonly available type of soil in the tropics. The excess soil generated from cut material was transformed into cement stabilized rammed earth, which is a cost effective material with low embodied energy. This is an ideal candidate for the construction of retaining walls and foundations, and such applications are demonstrated with adequate details. Further, many other types of sustainable building materials are highlighted with a case study of this housing model in a scheme of 13 housing units in Sri Lanka. The attention to detail required in construction and the applicability of alternative building materials and methods to improve the sustainability of such houses have been discussed in detail. These semi-tiered houses have the potential to address many of the current construction challenges.
- 1 April 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 16, 216-221
Numerical modelling of the behaviour of model shallow foundations on geocell reinforced sand
This paper focuses the development of a three dimensional numerical model to simulate the behaviour of geocell reinforced sand using PLAXIS 3D. Numerical modeling of the geocell has been an immense challenge due to their curved shape. Most of researchers used equivalent composite approach (ECA) to model the geocells. However, the composite method has a number of limitations, including the disregard of the effect of shape. The shape has a major influence in stress distribution. Hence a realistic model approach is essential to simulate the same experimental condition in numerical analysis. In this study, a 3D cad model was imported to PLAXIS 3D and modeled using geogrid structural element. Then the model was validated using experimental results where the results satisfied each other. Thereafter the depth that gives the highest carrying capacity was estimated using numerical and experimental result, which was found at depth(U) /width(B)<;0.5 for a square pad footing.
- 1 April 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 16, 216-221
Numerical modelling of the behaviour of model shallow foundations on geocell reinforced sand
This paper focuses the development of a three dimensional numerical model to simulate the behaviour of geocell reinforced sand using PLAXIS 3D. Numerical modeling of the geocell has been an immense challenge due to their curved shape. Most of researchers used equivalent composite approach (ECA) to model the geocells. However, the composite method has a number of limitations, including the disregard of the effect of shape. The shape has a major influence in stress distribution. Hence a realistic model approach is essential to simulate the same experimental condition in numerical analysis. In this study, a 3D cad model was imported to PLAXIS 3D and modeled using geogrid structural element. Then the model was validated using experimental results where the results satisfied each other. Thereafter the depth that gives the highest carrying capacity was estimated using numerical and experimental result, which was found at depth(U) /width(B)<;0.5 for a square pad footing.