Rhanim Hassan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Rhanim Hassan has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
A. Azim
3 shared publicationsC. Olagnon
Groupe d'Etudes de Métallurgie Physique et Physique des Matériaux (GEMPPM), URA CNRS 341, Bat. 502, INSA de Lyon, 69621 Villeurbanne, France
3 shared publicationsG. Fantozzi
Groupe d'Etudes de Métallurgie Physique et Physique des Matériaux (GEMPPM), URA CNRS 341, Bat. 502, INSA de Lyon, 69621 Villeurbanne, France
3 shared publicationsP. Archambault
2 shared publicationsR. Torrecillas
Instituto Nacional del Carbon, La Corredoria, s/n. Apartado 73, 33080 Oviedo, Spain
2 shared publicationsA. Nassim
Physics Department Laboratoire Instrumentation de Mesure et de Contrôle IMC Chouaïb Doukkali University, d'EL Jadida Maroc
1 shared publication
Latest Publications
- Open Access
- 3 May 2018
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 24 (2) , 208 - 212-212
Numerical Stress Intensity Factor in Polymer Structures
The purpose of this study was to determine the SIF stress intensity factor by numerical modeling of a structure containing a hole playing the role of a discontinuity " crack " subjected to a tensile load by the J- integral approach . The energy release rate was defined by modeling the crack by a notch and a double notch starting from the hole. The results were validated experimentally by testing a transparent material using the photoelasticity technology. stress intensity factor , finite element method j-integral , two-dimensional photoelasticity measurement ,monogenic signal.DOI: http://dx.doi.org/10.5755/j01.mech.24.2.17329
- 3 May 2018
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 24 (2) , 208 - 212-212
Open AccessNumerical Stress Intensity Factor in Polymer Structures
The purpose of this study was to determine the SIF stress intensity factor by numerical modeling of a structure containing a hole playing the role of a discontinuity " crack " subjected to a tensile load by the J- integral approach . The energy release rate was defined by modeling the crack by a notch and a double notch starting from the hole. The results were validated experimentally by testing a transparent material using the photoelasticity technology. stress intensity factor , finite element method j-integral , two-dimensional photoelasticity measurement ,monogenic signal.DOI: http://dx.doi.org/10.5755/j01.mech.24.2.17329
- 30 April 2009
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 48 (4) , 795-804
Problème inverse pour le traitement laser des métaux à transformations de phases
- 30 April 2009
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 48 (4) , 795-804
Problème inverse pour le traitement laser des métaux à transformations de phases
- 24 June 2006
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 34 (3) , 243-251
Experimental validation of inverse heat conduction method: quenching of steels XC42 and XC80
Two inverses methods are developed to calculate the surface heat flux and temperature of a body during heat treatment. Knowing temperature of an inner point of the solid and taking into account the phase transformation non-linearity, the surface heat flux evolution is estimated by an inverse algorithm. The experimental validation of both methods is performed in XC42 and XC80 steels case.
- 24 June 2006
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 34 (3) , 243-251
Experimental validation of inverse heat conduction method: quenching of steels XC42 and XC80
Two inverses methods are developed to calculate the surface heat flux and temperature of a body during heat treatment. Knowing temperature of an inner point of the solid and taking into account the phase transformation non-linearity, the surface heat flux evolution is estimated by an inverse algorithm. The experimental validation of both methods is performed in XC42 and XC80 steels case.
- 1 August 2003
- Published by Springer Nature in Journal of Materials Research
- Vol. 18 (8) , 1771-1776
High-temperature deformation of mullite and analysis of creep curves
The creep behavior of mullite was studied under different stresses and in the temperature range 1200–1450 °C, and an analysis of creep curves was proposed. The study of creep behavior of mullite at high temperatures clearly indicates that this material exhibits concurrent creep and slow crack growth. An effective transition stress exists at each temperature. The analysis takes account of the total creep curve; in particular, the primary and stationary stages. It is now possible to determine by extrapolation the steady-state creep rate for specimens that break in the transient domain during tests. Thus, one can verify the influence of the stress on the steady-state creep rate over a wide stress range. On the other hand, this analysis clearly indicates the existence of two values of the activation energy around 1300 °C; this suggests a change of creep mechanism at this temperature.
- 1 August 2003
- Published by Springer Nature in Journal of Materials Research
- Vol. 18 (8) , 1771-1776
High-temperature deformation of mullite and analysis of creep curves
The creep behavior of mullite was studied under different stresses and in the temperature range 1200–1450 °C, and an analysis of creep curves was proposed. The study of creep behavior of mullite at high temperatures clearly indicates that this material exhibits concurrent creep and slow crack growth. An effective transition stress exists at each temperature. The analysis takes account of the total creep curve; in particular, the primary and stationary stages. It is now possible to determine by extrapolation the steady-state creep rate for specimens that break in the transient domain during tests. Thus, one can verify the influence of the stress on the steady-state creep rate over a wide stress range. On the other hand, this analysis clearly indicates the existence of two values of the activation energy around 1300 °C; this suggests a change of creep mechanism at this temperature.
- 31 December 1997
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 17 (1) , 85-89
Crack propagation behaviour in mullite at high temperatures by double-torsion technique
- 31 December 1997
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 17 (1) , 85-89
Crack propagation behaviour in mullite at high temperatures by double-torsion technique
- 1 January 1997
- Published by Elsevier in Ceramics International
- Vol. 23 (6) , 497-507
Experimental characterisation of high temperature creep resistance of mullite
- 1 January 1997
- Published by Elsevier in Ceramics International
- Vol. 23 (6) , 497-507
Experimental characterisation of high temperature creep resistance of mullite