Peter E. J. Baldwin
Research Subjects
Peter E. J. Baldwin has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Andrew David Maynard
Arizona State University, Tempe, Arizona, USA
9 shared publications L.C. Kenny
4 shared publications- Kate Jones
Health and Safety Executive, Science and Research Centre , Harpur Hill, Buxton SK17 9JN
3 shared publications Chris Keen
Health and Safety Executive (HSE), Buxton, Derbyshire, UK
2 shared publicationsG.C. Beaumont
2 shared publications- John Cocker
Health & Safety Laboratory, Harpur Hill, Buxton, SK17 9JN, UK
2 shared publications
Latest Publications
- Open Access
- 9 January 2019
- Published by Oxford University Press (OUP) in Annals of Work Exposures and Health
- Vol. 63 (2) , 184-196
Exposure to Respirable Crystalline Silica in the GB Brick Manufacturing and Stone Working Industries
The aim of this work was to benchmark respirable crystalline silica (RCS) exposures in brick manufacturing and stone working sectors in Great Britain. This will contribute to a larger programme of work, which will be used to better understand the role of health surveillance in preventing the development of further cases of silicosis and chronic obstructive pulmonary disease. This work was undertaken by means of site visits to measure RCS and respirable dust exposures and assess exposure controls. In addition, historic exposure reports from the sites were collated to allow assessment of exposure trends. The survey, which was conducted in 20 sites (10 from each sector), found that in both sectors over 20% of the measured exposures exceeded the UK RCS 8-hour time-weighted averaged workplace exposure limit (WEL) of 0.1 mg/m(3). In the stone sector over 40% of the 8 h time-weighted average RCS exposures were above the RCS WEL compared to 20% in the brick manufacturing sector. In the stone sector, 61% of RCS exposures where water suppression was present exceeded the RCS WEL. This indicates that a variety of exposure controls will be required to control RCS exposures, including respiratory protective equipment (RPE). The use of RPE in situations where RCS exposure exceeded the RCS WEL was more prevalent in stone working than in the brick sector. There were differences associated with RPE and the use of other exposure controls in both sectors. The contextual information in historic consultants exposure reports was generally limited, with exposure controls either not mentioned or not fully described. This affects the usefulness of exposure monitoring to dutyholders. This work will provide information on exposures allowing construction of lifetime exposure estimates for use in analysis of the health effects data. A second survey to the sites is planned to determine how exposures have altered.
- 9 January 2019
- Published by Oxford University Press (OUP) in Annals of Work Exposures and Health
- Vol. 63 (2) , 184-196
Open AccessExposure to Respirable Crystalline Silica in the GB Brick Manufacturing and Stone Working Industries
The aim of this work was to benchmark respirable crystalline silica (RCS) exposures in brick manufacturing and stone working sectors in Great Britain. This will contribute to a larger programme of work, which will be used to better understand the role of health surveillance in preventing the development of further cases of silicosis and chronic obstructive pulmonary disease. This work was undertaken by means of site visits to measure RCS and respirable dust exposures and assess exposure controls. In addition, historic exposure reports from the sites were collated to allow assessment of exposure trends. The survey, which was conducted in 20 sites (10 from each sector), found that in both sectors over 20% of the measured exposures exceeded the UK RCS 8-hour time-weighted averaged workplace exposure limit (WEL) of 0.1 mg/m(3). In the stone sector over 40% of the 8 h time-weighted average RCS exposures were above the RCS WEL compared to 20% in the brick manufacturing sector. In the stone sector, 61% of RCS exposures where water suppression was present exceeded the RCS WEL. This indicates that a variety of exposure controls will be required to control RCS exposures, including respiratory protective equipment (RPE). The use of RPE in situations where RCS exposure exceeded the RCS WEL was more prevalent in stone working than in the brick sector. There were differences associated with RPE and the use of other exposure controls in both sectors. The contextual information in historic consultants exposure reports was generally limited, with exposure controls either not mentioned or not fully described. This affects the usefulness of exposure monitoring to dutyholders. This work will provide information on exposures allowing construction of lifetime exposure estimates for use in analysis of the health effects data. A second survey to the sites is planned to determine how exposures have altered.
- Open Access
- 14 February 2017
- Published by Oxford University Press (OUP) in Annals of Work Exposures and Health
- Vol. 61 (3) , 383-393
Exposure to Diisocyanates and Their Corresponding Diamines in Seven Different Workplaces
Biological monitoring to assess exposure to diisocyanates in the workplace is becoming increasingly widespread due to its relative ease of use and ability to look at all exposure routes. Currently, biological monitoring measures the corresponding isocyanate-derived diamine in urine, after hydrolysis. Because of this, any exposure to the diamines themselves released during the industrial process could confound the assessment of diisocyanate exposure. This paper reports an initial assessment of the extent of diamine formation and exposure during different processes involving diisocyanates including casting, grouting, core making, spray painting, foam blowing, and floor screeding. Air monitoring and glove analysis were conducted for both the relevant diisocyanate (measured as total NCO) and its corresponding diamine; urine samples were analysed (after hydrolysis) for the isocyanate-derived diamine. Processes that generated aerosols (as demonstrated by impinger analysis) such as spray painting and foam blowing were associated with the detection of diamines. Those processes that did not generate aerosols (casting, grouting, core making, and screeding) had no diamines detected, either in air or on gloves. In spray-painting tasks, diamines were a minor component (5 µmol mol−1 creatinine) despite airborne levels being well within occupational exposure limits (20 µg m−3 total NCO in Great Britain); measurement data and statistical modelling indicated that skin absorption was the most likely exposure route. Foam blowing exposures were more complex, but urinary levels were greater than those expected from diisocyanate inhalation alone (measured as total NCO). This study provides evidence that biological monitoring for diisocyanates based on measuring the corresponding diamine in urine is valid, although any co-exposure to diamines themselves should be considered when interpreting results. It also demonstrates the potential for substantial skin absorption of diisocyanates in certain processes such as floor screeding and foam production.
- 14 February 2017
- Published by Oxford University Press (OUP) in Annals of Work Exposures and Health
- Vol. 61 (3) , 383-393
Open AccessExposure to Diisocyanates and Their Corresponding Diamines in Seven Different Workplaces
Biological monitoring to assess exposure to diisocyanates in the workplace is becoming increasingly widespread due to its relative ease of use and ability to look at all exposure routes. Currently, biological monitoring measures the corresponding isocyanate-derived diamine in urine, after hydrolysis. Because of this, any exposure to the diamines themselves released during the industrial process could confound the assessment of diisocyanate exposure. This paper reports an initial assessment of the extent of diamine formation and exposure during different processes involving diisocyanates including casting, grouting, core making, spray painting, foam blowing, and floor screeding. Air monitoring and glove analysis were conducted for both the relevant diisocyanate (measured as total NCO) and its corresponding diamine; urine samples were analysed (after hydrolysis) for the isocyanate-derived diamine. Processes that generated aerosols (as demonstrated by impinger analysis) such as spray painting and foam blowing were associated with the detection of diamines. Those processes that did not generate aerosols (casting, grouting, core making, and screeding) had no diamines detected, either in air or on gloves. In spray-painting tasks, diamines were a minor component (5 µmol mol−1 creatinine) despite airborne levels being well within occupational exposure limits (20 µg m−3 total NCO in Great Britain); measurement data and statistical modelling indicated that skin absorption was the most likely exposure route. Foam blowing exposures were more complex, but urinary levels were greater than those expected from diisocyanate inhalation alone (measured as total NCO). This study provides evidence that biological monitoring for diisocyanates based on measuring the corresponding diamine in urine is valid, although any co-exposure to diamines themselves should be considered when interpreting results. It also demonstrates the potential for substantial skin absorption of diisocyanates in certain processes such as floor screeding and foam production.
- Open Access
- 1 March 2015
- Published by Walter de Gruyter GmbH in Archives of Industrial Hygiene and Toxicology
- Vol. 66 (1) , 23-29
Levels of soya aeroallergens during dockside unloading as measured by personal and static sampling / Razine aeroalergena soje za vrijeme iskrcavanja na lučkom doku
Soya is an important worldwide agricultural product widely shipped and imported in bulk. It contains a number of recognised allergens and the use of soya products and its dockside unloading have been associated with occupational asthma and community episodes of asthma. Two recognised inhalation soya allergens, soya trypsin inhibitor (STI) and hydrophobic soya protein (HSP), were measured in personal and static air samples collected at a United Kingdom (UK) dock during 3 days of unloading three bulks of processed soya beans and soya pelletised husk. Static samples included task-related and those taken at the workplace perimeter and neighbouring sites. Soluble total protein (STP) and gravimetric dust analyses were also undertaken. While gravimetric dust results in personal air samples were below half of the current UK exposure limit of 10 mg m-3 for grain dust, and generally less than 0.5 mg m-3 for the static samples, airborne concentrations for STI and HSP ranged between 0-3,071 and 11-12,629 ng m-3, respectively, while the correlation between the two specific allergen measurements was generally good (Rank Spearman coefficient 0.74). The data from this investigation suggest that HSP is a more sensitive indicator of soya exposure than STI, but only for soya husk, while STI may be equipotent in detecting exposure to both hull and bean derived soya products. Both assays appear sensitive techniques for investigating the control of exposure to allergenic soy material. The endotoxin level in the husk bulk was 15-60-fold that found in the two chipped bean bulks.
- 1 March 2015
- Published by Walter de Gruyter GmbH in Archives of Industrial Hygiene and Toxicology
- Vol. 66 (1) , 23-29
Open AccessLevels of soya aeroallergens during dockside unloading as measured by personal and static sampling / Razine aeroalergena soje za vrijeme iskrcavanja na lučkom doku
Soya is an important worldwide agricultural product widely shipped and imported in bulk. It contains a number of recognised allergens and the use of soya products and its dockside unloading have been associated with occupational asthma and community episodes of asthma. Two recognised inhalation soya allergens, soya trypsin inhibitor (STI) and hydrophobic soya protein (HSP), were measured in personal and static air samples collected at a United Kingdom (UK) dock during 3 days of unloading three bulks of processed soya beans and soya pelletised husk. Static samples included task-related and those taken at the workplace perimeter and neighbouring sites. Soluble total protein (STP) and gravimetric dust analyses were also undertaken. While gravimetric dust results in personal air samples were below half of the current UK exposure limit of 10 mg m-3 for grain dust, and generally less than 0.5 mg m-3 for the static samples, airborne concentrations for STI and HSP ranged between 0-3,071 and 11-12,629 ng m-3, respectively, while the correlation between the two specific allergen measurements was generally good (Rank Spearman coefficient 0.74). The data from this investigation suggest that HSP is a more sensitive indicator of soya exposure than STI, but only for soya husk, while STI may be equipotent in detecting exposure to both hull and bean derived soya products. Both assays appear sensitive techniques for investigating the control of exposure to allergenic soy material. The endotoxin level in the husk bulk was 15-60-fold that found in the two chipped bean bulks.
- 1 August 2012
- Published by Elsevier in Toxicology Letters
- Vol. 213 (1) , 3-8
A follow up study of occupational exposure to 4,4′-methylene-bis(2-chloroaniline) (MbOCA) and isocyanates in polyurethane manufacture in the UK
- 1 August 2012
- Published by Elsevier in Toxicology Letters
- Vol. 213 (1) , 3-8
A follow up study of occupational exposure to 4,4′-methylene-bis(2-chloroaniline) (MbOCA) and isocyanates in polyurethane manufacture in the UK
- 15 May 2009
- Published by Oxford University Press (OUP) in Annals of Occupational Hygiene
- Vol. 53 (5) , 499-507
A Survey of Occupational Exposure to 4,4′-methylene-bis (2-chloroaniline) (MbOCA) in the UK
Objectives: The main objective of the study was to gather information about the current controls and levels of exposure to 4,4′-methylene-bis (2-chloroaniline) (MbOCA) in a representative cross section of workplaces that use it to manufacture polyurethane elastomers. The study also aimed to investigate whether controls and guidance could be improved and to investigate exposure to isocyanates in these workplaces using biological monitoring. Methods: An occupational hygienist and a field scientist visited the two UK suppliers and 20 out of the 25 workplaces known to be using MbOCA in the UK during 2005 and 2006. They collected air samples, surface wipes, gloves, and urine samples and made observations to assess exposure and the adequacy of controls. All samples were analysed for MbOCA and urine samples were additionally analysed for isocyanate metabolites. A statistical analysis was made of the results. Results: Only 2.5% of the 80 personal inhalation exposures to MbOCA exceeded the workplace exposure limit of 5 μg m−3 8-h time-weighted average and 84% were below the limit of detection (LOD). Surface samples (n = 334) were collected from MbOCA users and suppliers and 60% had detectable levels of MbOCA ranging from 0.019 to 400 μg cm−2. The highest levels were around a hopper, ovens, and the weighing and pouring areas. MbOCA was also detected in 8 of the 75 samples collected from areas not likely to be in contact with MbOCA. At the two suppliers, samples (n = 28) were collected from the outside surfaces of recently imported kegs, pallets, and the floor around kegs. Six samples had detectable levels and four of these (0.2, 0.8, 1, and 6 μg cm−2) were from the floor and pallets in both suppliers. The other two positive results were found on the outside rim (18 μg cm−2) and side (23 μg cm−2) of a keg at one supplier indicating contamination by the manufacturer. Urine samples (n = 79) were collected and 49% were below the LOD for MbOCA and only three samples had levels of MbOCA that exceeded the biological monitoring guidance value (BMGV) of 15 μmol mol−1 creatinine. The highest urinary MbOCA concentrations were in samples from workers casting and moulding. The 90th percentile of the urine MbOCA results was 8.6 μmol MbOCA per mol creatinine. Urine samples were also analysed for the diamine metabolites of toluene diisocyanate and hexamethylene diisocyanate and 33% had detectable levels with 22 and 13% of results, respectively, above the BMGV for isocyanates (1 μmol isocyanate-derived diamine per mol creatinine). The maximum urinary concentration of toluene diamine and hexane diamine were 15.6 and 10.1 μmol mol−1 creatinine, respectively. Conclusions: The survey found that the measures used to control exposure to MbOCA could be improved. Although air levels of MbOCA were generally low, there was evidence of spread of surface contamination and poor maintenance of controls such as local exhaust ventilation. A BMGV based on the 90th percentile of data from workplaces with good control would be less than the 90% value of 8.6 μmol mol−1 creatinine found in this study and suggests that the current BMGV of 15 μmol mol−1 creatinine is no longer acting as a stimulus to reduce exposure. The metabolites of isocyanates found in urine samples in this study could arise from inhalation exposure to isocyanates or from dermal exposure to either isocyanates or their diamine breakdown product and need further investigation.
- 15 May 2009
- Published by Oxford University Press (OUP) in Annals of Occupational Hygiene
- Vol. 53 (5) , 499-507
A Survey of Occupational Exposure to 4,4′-methylene-bis (2-chloroaniline) (MbOCA) in the UK
Objectives: The main objective of the study was to gather information about the current controls and levels of exposure to 4,4′-methylene-bis (2-chloroaniline) (MbOCA) in a representative cross section of workplaces that use it to manufacture polyurethane elastomers. The study also aimed to investigate whether controls and guidance could be improved and to investigate exposure to isocyanates in these workplaces using biological monitoring. Methods: An occupational hygienist and a field scientist visited the two UK suppliers and 20 out of the 25 workplaces known to be using MbOCA in the UK during 2005 and 2006. They collected air samples, surface wipes, gloves, and urine samples and made observations to assess exposure and the adequacy of controls. All samples were analysed for MbOCA and urine samples were additionally analysed for isocyanate metabolites. A statistical analysis was made of the results. Results: Only 2.5% of the 80 personal inhalation exposures to MbOCA exceeded the workplace exposure limit of 5 μg m−3 8-h time-weighted average and 84% were below the limit of detection (LOD). Surface samples (n = 334) were collected from MbOCA users and suppliers and 60% had detectable levels of MbOCA ranging from 0.019 to 400 μg cm−2. The highest levels were around a hopper, ovens, and the weighing and pouring areas. MbOCA was also detected in 8 of the 75 samples collected from areas not likely to be in contact with MbOCA. At the two suppliers, samples (n = 28) were collected from the outside surfaces of recently imported kegs, pallets, and the floor around kegs. Six samples had detectable levels and four of these (0.2, 0.8, 1, and 6 μg cm−2) were from the floor and pallets in both suppliers. The other two positive results were found on the outside rim (18 μg cm−2) and side (23 μg cm−2) of a keg at one supplier indicating contamination by the manufacturer. Urine samples (n = 79) were collected and 49% were below the LOD for MbOCA and only three samples had levels of MbOCA that exceeded the biological monitoring guidance value (BMGV) of 15 μmol mol−1 creatinine. The highest urinary MbOCA concentrations were in samples from workers casting and moulding. The 90th percentile of the urine MbOCA results was 8.6 μmol MbOCA per mol creatinine. Urine samples were also analysed for the diamine metabolites of toluene diisocyanate and hexamethylene diisocyanate and 33% had detectable levels with 22 and 13% of results, respectively, above the BMGV for isocyanates (1 μmol isocyanate-derived diamine per mol creatinine). The maximum urinary concentration of toluene diamine and hexane diamine were 15.6 and 10.1 μmol mol−1 creatinine, respectively. Conclusions: The survey found that the measures used to control exposure to MbOCA could be improved. Although air levels of MbOCA were generally low, there was evidence of spread of surface contamination and poor maintenance of controls such as local exhaust ventilation. A BMGV based on the 90th percentile of data from workplaces with good control would be less than the 90% value of 8.6 μmol mol−1 creatinine found in this study and suggests that the current BMGV of 15 μmol mol−1 creatinine is no longer acting as a stimulus to reduce exposure. The metabolites of isocyanates found in urine samples in this study could arise from inhalation exposure to isocyanates or from dermal exposure to either isocyanates or their diamine breakdown product and need further investigation.
- 4 June 2007
- Published by Oxford University Press (OUP) in Occupational Medicine
- Vol. 57 (5) , 362-366
Dehydroabietic acid as a biomarker for exposure to colophony
Background Colophony (rosin) is a natural product derived from the resin of coniferous trees with many industrial applications including soldering fluxes. Exposure to colophony fume through soldering is one of the leading causes of occupational asthma in the UK.
- 4 June 2007
- Published by Oxford University Press (OUP) in Occupational Medicine
- Vol. 57 (5) , 362-366
Dehydroabietic acid as a biomarker for exposure to colophony
Background Colophony (rosin) is a natural product derived from the resin of coniferous trees with many industrial applications including soldering fluxes. Exposure to colophony fume through soldering is one of the leading causes of occupational asthma in the UK.
- 1 January 2007
- Published by ASME International
- p. 913-920
Advanced Supersonic Component Engine for Military Applications
A 1500 kWe Brayton cycle engine is in development that has the efficiency of a diesel, but with the size, weight and maintenance attributes of a gas turbine. The Advanced Supersonic Component Engine (ASCE) combines many of the proven features of shock wave compression and expansion systems, commonly used in supersonic flight inlet and nozzle designs, with turbo-machinery practices employed in conventional axial flow gas turbines. The superior efficiency of the ASCE is a result of high pressure shock wave compression and supersonic expansion phenomena that produce high component efficiencies and a unique engine configuration that minimizes flow stream turning losses throughout the system. The engine employs a two stage counter-rotating configuration to achieve a 30:1 pressure ratio and a 42% simple cycle efficient engine to drive a high-speed direct drive permanent magnet (PM) electric motor/generator for all electric power and propulsion applications. The system promises a specific fuel consumption equal to or better than current reciprocating diesel engines in this size range, but with a 10:1 weight reduction and a 4:1 improvement in time-between-overall compared to marine diesel systems in this size range. This is a 2:1 increase in fuel efficiency at full power over existing gas turbines in this size range.
- 1 January 2007
- Published by ASME International
- p. 913-920
Advanced Supersonic Component Engine for Military Applications
A 1500 kWe Brayton cycle engine is in development that has the efficiency of a diesel, but with the size, weight and maintenance attributes of a gas turbine. The Advanced Supersonic Component Engine (ASCE) combines many of the proven features of shock wave compression and expansion systems, commonly used in supersonic flight inlet and nozzle designs, with turbo-machinery practices employed in conventional axial flow gas turbines. The superior efficiency of the ASCE is a result of high pressure shock wave compression and supersonic expansion phenomena that produce high component efficiencies and a unique engine configuration that minimizes flow stream turning losses throughout the system. The engine employs a two stage counter-rotating configuration to achieve a 30:1 pressure ratio and a 42% simple cycle efficient engine to drive a high-speed direct drive permanent magnet (PM) electric motor/generator for all electric power and propulsion applications. The system promises a specific fuel consumption equal to or better than current reciprocating diesel engines in this size range, but with a 10:1 weight reduction and a 4:1 improvement in time-between-overall compared to marine diesel systems in this size range. This is a 2:1 increase in fuel efficiency at full power over existing gas turbines in this size range.
- 11 August 1999
- Published by Elsevier in Journal of Aerosol Science
- Vol. 30 (9) , 1215-1226
Development of a system to rapidly measure sampler penetration up to 20 μm aerodynamic diameter in calm air, using the aerodynamic particle sizer
- 11 August 1999
- Published by Elsevier in Journal of Aerosol Science
- Vol. 30 (9) , 1215-1226
Development of a system to rapidly measure sampler penetration up to 20 μm aerodynamic diameter in calm air, using the aerodynamic particle sizer
- 1 June 1999
- Published by Elsevier in Journal of Aerosol Science
- Vol. 30 (5) , 613-626
AEROSOL INHALABILITY IN LOW AIR MOVEMENT ENVIRONMENTS
- 1 June 1999
- Published by Elsevier in Journal of Aerosol Science
- Vol. 30 (5) , 613-626
AEROSOL INHALABILITY IN LOW AIR MOVEMENT ENVIRONMENTS