Tian Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tian Zheng has a total of 92 co-authors. Here are the top co-authors by number of shared publications:
- Michael J. Higgins
Intelligent Polymer Research Institute, University of Wollongong, NSW 2522, wollongong, AUSTRALIA
9 shared publications - Gordon George Wallace
University of Wollongong
6 shared publications Ce Wang
Jilin University
5 shared publications- Ce Wang
Jilin University
5 shared publications Chengcheng Zhang
Jilin University
5 shared publicationsXiaoteng Jia
5 shared publications
Latest Publications
- 27 May 2020
- Published by IOP Publishing in Nanotechnology
- Vol. 31 (37) , 375708
Nanoscale piezoelectric effect of biodegradable PLA-based composite fibers by piezoresponse force microscopy
The piezoelectricity of the biocompatible and biodegradable polymer polylactic acid (PLA) was investigated as a potential magnetoelectric (ME) nanocomposite for biomedical applications. A key focus was to quantify the piezoelectric properties of single PLA fibers while tuning their polymer degradability through the addition of faster degrading polymer, poly (DL-lactide-co-glycolide) (PLGA), which is not a piezoelectric polymer. Piezoresponse Force Microscopy (PFM) showed that electrospun PLA fibers gave a piezoelectric response of 186 ± 28 pm. For comparison both PLA/PLGA (75/25) and PLA/PLGA (50/50) fibers gave significantly lower piezoelectric responses of 89 ± 12 pm and 50 ± 9.1 pm, respectively. For the highest content PLGA fibers, PLA/PLGA (25/75), only very few fibers exhibited a low response of 28 pm while most showed no response. Overall, an increasing PLGA content caused a decrease in the piezoelectric response, thus an expected trade-off existed between the biodegradability (i.e. PLA to PLGA content ratio) versus piezoelectricity. The findings were considered significant due to the existence of piezoelectricity in a tuneable biodegradable material that has potential to impart piezoelectric induced effects on biointeractions with the surrounding biological environment or drug interactions with the polymer to control the rate of drug release. In such applications, there is an opportunity to magnetically control the piezoelectricity and henceforth PLA/CoFe 2 O 4 ME nanocomposite fibers with 5% and 10% of CoFe 2 O 4 nanoparticles were also investigated. Both 5% and 10% PLA/CoFe 2 O 4 nanocomposites gave lower piezoelectric responses compared to the PLA presumably due to the disturbance of polymer chains and dipole moments by the magnetic nanoparticles, in addition to effects from the possible inhomogeneous distribution of CoFe 2 O 4 nanoparticles.
- 27 May 2020
- Published by IOP Publishing in Nanotechnology
- Vol. 31 (37) , 375708
Nanoscale piezoelectric effect of biodegradable PLA-based composite fibers by piezoresponse force microscopy
The piezoelectricity of the biocompatible and biodegradable polymer polylactic acid (PLA) was investigated as a potential magnetoelectric (ME) nanocomposite for biomedical applications. A key focus was to quantify the piezoelectric properties of single PLA fibers while tuning their polymer degradability through the addition of faster degrading polymer, poly (DL-lactide-co-glycolide) (PLGA), which is not a piezoelectric polymer. Piezoresponse Force Microscopy (PFM) showed that electrospun PLA fibers gave a piezoelectric response of 186 ± 28 pm. For comparison both PLA/PLGA (75/25) and PLA/PLGA (50/50) fibers gave significantly lower piezoelectric responses of 89 ± 12 pm and 50 ± 9.1 pm, respectively. For the highest content PLGA fibers, PLA/PLGA (25/75), only very few fibers exhibited a low response of 28 pm while most showed no response. Overall, an increasing PLGA content caused a decrease in the piezoelectric response, thus an expected trade-off existed between the biodegradability (i.e. PLA to PLGA content ratio) versus piezoelectricity. The findings were considered significant due to the existence of piezoelectricity in a tuneable biodegradable material that has potential to impart piezoelectric induced effects on biointeractions with the surrounding biological environment or drug interactions with the polymer to control the rate of drug release. In such applications, there is an opportunity to magnetically control the piezoelectricity and henceforth PLA/CoFe 2 O 4 ME nanocomposite fibers with 5% and 10% of CoFe 2 O 4 nanoparticles were also investigated. Both 5% and 10% PLA/CoFe 2 O 4 nanocomposites gave lower piezoelectric responses compared to the PLA presumably due to the disturbance of polymer chains and dipole moments by the magnetic nanoparticles, in addition to effects from the possible inhomogeneous distribution of CoFe 2 O 4 nanoparticles.
- Open Access
- 20 December 2018
- Published by Wiley in Polymer International
- Vol. 68 (4) , 735-745
Melt electrowriting of electroactive poly(vinylidene difluoride) fibers
Poly(vinylidene difluoride) (PVDF) has piezoelectric properties suitable for numerous applications such as flexible electronics, sensing and biomedical materials. In this study, individual fibers with diameters ranging from 17 to 55 µm were processed using melt electrowriting (MEW). Electroactive PVDF fibers can be fabricated via MEW, while the polymer can remain molten for up to 10 h without noticeable changes in the resulting fiber diameter. MEW processing parameters for PVDF were investigated, including applied voltage, pressure and temperature. A rapid fiber characterization methodology for MEW that automatically determines the fiber diameters from camera images taken of microscope slides was developed and validated. The outputs from this approach followed previous MEW processing trends already identified with different polymers, although overestimation of fiber diameters d33 ≈ 19 pm V–1. © 2018 Society of Chemical Industry
- 20 December 2018
- Published by Wiley in Polymer International
- Vol. 68 (4) , 735-745
Open AccessMelt electrowriting of electroactive poly(vinylidene difluoride) fibers
Poly(vinylidene difluoride) (PVDF) has piezoelectric properties suitable for numerous applications such as flexible electronics, sensing and biomedical materials. In this study, individual fibers with diameters ranging from 17 to 55 µm were processed using melt electrowriting (MEW). Electroactive PVDF fibers can be fabricated via MEW, while the polymer can remain molten for up to 10 h without noticeable changes in the resulting fiber diameter. MEW processing parameters for PVDF were investigated, including applied voltage, pressure and temperature. A rapid fiber characterization methodology for MEW that automatically determines the fiber diameters from camera images taken of microscope slides was developed and validated. The outputs from this approach followed previous MEW processing trends already identified with different polymers, although overestimation of fiber diameters d33 ≈ 19 pm V–1. © 2018 Society of Chemical Industry
- 8 June 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (26) , 22031-22041
A “Tandem” Strategy to Fabricate Flexible Graphene/Polypyrrole Nanofiber Film Using the Surfactant-Exfoliated Graphene for Supercapacitors
The surfactant-assisted liquid-phase exfoliation of expanded graphite can produce graphene sheets in large quantities with minimal defects. However, it is difficult to completely remove the surfactant from the final product, thus affecting the electrochemical properties of the produced graphene. In this article, a novel approach to fabricate flexible graphene/polypyrrole film was developed: using surfactant cetyltrimethylammonium bromide as a template for growth of polypyrrole nanofibers (PPyNFs) instead of removal after the exfoliation process; followed by a simple filtration method. The introduction of PPyNF not only increases the electrochemical performance, but also ensures flexibility. This composite film electrode offers a capacitance up to 161 F g–1 along with a capacitance retention rate of over 80% after 5000 cycles.
- 8 June 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (26) , 22031-22041
A “Tandem” Strategy to Fabricate Flexible Graphene/Polypyrrole Nanofiber Film Using the Surfactant-Exfoliated Graphene for Supercapacitors
The surfactant-assisted liquid-phase exfoliation of expanded graphite can produce graphene sheets in large quantities with minimal defects. However, it is difficult to completely remove the surfactant from the final product, thus affecting the electrochemical properties of the produced graphene. In this article, a novel approach to fabricate flexible graphene/polypyrrole film was developed: using surfactant cetyltrimethylammonium bromide as a template for growth of polypyrrole nanofibers (PPyNFs) instead of removal after the exfoliation process; followed by a simple filtration method. The introduction of PPyNF not only increases the electrochemical performance, but also ensures flexibility. This composite film electrode offers a capacitance up to 161 F g–1 along with a capacitance retention rate of over 80% after 5000 cycles.
- 12 February 2018
- Published by Wiley in Advanced Energy Materials
- Vol. 8 (15)
Boosting the Potassium Storage Performance of Alloy‐Based Anode Materials via Electrolyte Salt Chemistry
Potassium‐ion batteries (PIBs) are promising energy storage systems because of the abundance and low cost of potassium. The formidable challenge is to develop suitable electrode materials and electrolytes for accommodating the relatively large size and high activity of potassium. Herein, Bi‐based materials are reported as novel anodes for PIBs. Nanostructural design and proper selection of the electrolyte salt have been used to achieve excellent cycling performance. It is found that the potassiation of Bi undergoes a solid‐solution reaction, followed by two typical two‐phase reactions, corresponding to Bi ↔ Bi(K) and Bi(K) ↔ K5Bi4 ↔ K3Bi, respectively. By choosing potassium bis(fluorosulfonyl)imide (KFSI) to replace potassium hexafluorophosphate (KPF6) in carbonate electrolyte, a more stable solid electrolyte interphase layer is achieved and results in notably enhanced electrochemical performance. More importantly, the KFSI salt is very versatile and can significantly promote the electrochemical performance of other alloy‐based anode materials, such as Sn and Sb.
- 12 February 2018
- Published by Wiley in Advanced Energy Materials
- Vol. 8 (15)
Boosting the Potassium Storage Performance of Alloy‐Based Anode Materials via Electrolyte Salt Chemistry
Potassium‐ion batteries (PIBs) are promising energy storage systems because of the abundance and low cost of potassium. The formidable challenge is to develop suitable electrode materials and electrolytes for accommodating the relatively large size and high activity of potassium. Herein, Bi‐based materials are reported as novel anodes for PIBs. Nanostructural design and proper selection of the electrolyte salt have been used to achieve excellent cycling performance. It is found that the potassiation of Bi undergoes a solid‐solution reaction, followed by two typical two‐phase reactions, corresponding to Bi ↔ Bi(K) and Bi(K) ↔ K5Bi4 ↔ K3Bi, respectively. By choosing potassium bis(fluorosulfonyl)imide (KFSI) to replace potassium hexafluorophosphate (KPF6) in carbonate electrolyte, a more stable solid electrolyte interphase layer is achieved and results in notably enhanced electrochemical performance. More importantly, the KFSI salt is very versatile and can significantly promote the electrochemical performance of other alloy‐based anode materials, such as Sn and Sb.
An Electrosynthesized 3D Porous Molybdenum Sulfide/Graphene Film with Enhanced Electrochemical Performance for Lithium Storage
Molybdenum sulfide/graphene composites are promising anode materials for lithium‐ion batteries (LIBs). In this work, MoSx/graphene composite film with an ideal 3D porous structure is developed via a facile and straightforward electrochemical route. The MoSx nanoparticles are uniformly anchored on the graphene nanosheets that are randomly arranged, resulting in MoSx/graphene composites with well‐developed porous structure. Benefiting from such structure and the synergistic effect from two components, this material shows a high specific capacity over 1200 mA h g−1, an excellent rate performance, and superior cycling stability. The dominating pseudocapacitive behavior in Li storage contributes to the outstanding rate capacity. Importantly, this kind of novel material can be easily produced as 3D microelectrodes for microscaled LIBs that are highly demanded for autonomous microelectronic systems.
An Electrosynthesized 3D Porous Molybdenum Sulfide/Graphene Film with Enhanced Electrochemical Performance for Lithium Storage
Molybdenum sulfide/graphene composites are promising anode materials for lithium‐ion batteries (LIBs). In this work, MoSx/graphene composite film with an ideal 3D porous structure is developed via a facile and straightforward electrochemical route. The MoSx nanoparticles are uniformly anchored on the graphene nanosheets that are randomly arranged, resulting in MoSx/graphene composites with well‐developed porous structure. Benefiting from such structure and the synergistic effect from two components, this material shows a high specific capacity over 1200 mA h g−1, an excellent rate performance, and superior cycling stability. The dominating pseudocapacitive behavior in Li storage contributes to the outstanding rate capacity. Importantly, this kind of novel material can be easily produced as 3D microelectrodes for microscaled LIBs that are highly demanded for autonomous microelectronic systems.
- 12 October 2017
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 46 (44) , 15582-15588
Enhancement of charge separation in ferroelectric heterogeneous photocatalyst Bi 4 (SiO 4 ) 3 /Bi 2 SiO 5 nanostructures
Excellent photocatalytic activity is given rise to enhanced charge separation in ferroelectric heterogeneous Bi 4 (SiO 4 ) 3 /Bi 2 SiO 5 photocatalyst.
- 12 October 2017
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 46 (44) , 15582-15588
Enhancement of charge separation in ferroelectric heterogeneous photocatalyst Bi 4 (SiO 4 ) 3 /Bi 2 SiO 5 nanostructures
Excellent photocatalytic activity is given rise to enhanced charge separation in ferroelectric heterogeneous Bi 4 (SiO 4 ) 3 /Bi 2 SiO 5 photocatalyst.
- 7 August 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry B
- Vol. 5 (35) , 7352-7359
Human skin interactive self-powered wearable piezoelectric bio-e-skin by electrospun poly- l -lactic acid nanofibers for non-invasive physiological signal monitoring
Flexible and wearable piezoelectric bio e-skin (PBio-e-skin) based on electrospun poly(L-lactic acid) PLLA nanofiber membrane is demonstrated for non-invasive human physiological signal monitoring and detecting dynamic tactile stimuli. The molecular orientations of the CO dipoles by electrospinning technique result in a longitudinal piezoelectric charge co-efficient (d33) value of ∼(3 ± 1) pm V−1 realized by piezoresponse force microscopy, allowing the PBio-e-skin for pressure sensing applications. The robust mechanical strength (Young's modulus ∼50 MPa) of nanofiber membrane ensures PBio-e-skin's superior operational stability over 375 000 cycles. Owing to the superior mechanosensitivity of ∼22 V N−1, PBio-e-skin has the ability to measure subtle movement of muscle in the internal organs such as esophagus, trachea, motion of joints and arterial pressure by recognition of strains on human skin. This flexible and light weight PBio-e-skin precisely detects vital signs and provides important clinical insights without using any external power source. Eventually, the low cost, environmental friendly PBio-e-skin will have a huge impact in a broad range of applications including self-powered wearable health care systems, human–machine interfacing devices, artificial intelligence and prosthetic skin.
- 7 August 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry B
- Vol. 5 (35) , 7352-7359
Human skin interactive self-powered wearable piezoelectric bio-e-skin by electrospun poly- l -lactic acid nanofibers for non-invasive physiological signal monitoring
Flexible and wearable piezoelectric bio e-skin (PBio-e-skin) based on electrospun poly(L-lactic acid) PLLA nanofiber membrane is demonstrated for non-invasive human physiological signal monitoring and detecting dynamic tactile stimuli. The molecular orientations of the CO dipoles by electrospinning technique result in a longitudinal piezoelectric charge co-efficient (d33) value of ∼(3 ± 1) pm V−1 realized by piezoresponse force microscopy, allowing the PBio-e-skin for pressure sensing applications. The robust mechanical strength (Young's modulus ∼50 MPa) of nanofiber membrane ensures PBio-e-skin's superior operational stability over 375 000 cycles. Owing to the superior mechanosensitivity of ∼22 V N−1, PBio-e-skin has the ability to measure subtle movement of muscle in the internal organs such as esophagus, trachea, motion of joints and arterial pressure by recognition of strains on human skin. This flexible and light weight PBio-e-skin precisely detects vital signs and provides important clinical insights without using any external power source. Eventually, the low cost, environmental friendly PBio-e-skin will have a huge impact in a broad range of applications including self-powered wearable health care systems, human–machine interfacing devices, artificial intelligence and prosthetic skin.
- Open Access
- 28 June 2017
- Published by Springer Nature in Nature Communications
- Vol. 8 (1) , 1-8
Cellulose-based magnetoelectric composites
Since the first magnetoelectric polymer composites were fabricated more than a decade ago, there has been a reluctance to use piezoelectric polymers other than poly(vinylidene fluoride) and its copolymers due to their well-defined piezoelectric mechanism and high piezoelectric coefficients that lead to superior magnetoelectric coefficients of >1 V cm−1 Oe−1. This is the current situation despite the potential for other piezoelectric polymers, such as natural biopolymers, to bring unique, added-value properties and functions to magnetoelectric composite devices. Here we demonstrate a cellulose-based magnetoelectric laminate composite that produces considerable magnetoelectric coefficients of ≈1.5 V cm−1 Oe−1, comprising a Fano resonance that is ubiquitous in the field of physics, such as photonics, though never experimentally observed in magnetoelectric composites. The work successfully demonstrates the concept of exploring new advances in using biopolymers in magnetoelectric composites, particularly cellulose, which is increasingly employed as a renewable, low-cost, easily processable and degradable material.
- 28 June 2017
- Published by Springer Nature in Nature Communications
- Vol. 8 (1) , 1-8
Open AccessCellulose-based magnetoelectric composites
Since the first magnetoelectric polymer composites were fabricated more than a decade ago, there has been a reluctance to use piezoelectric polymers other than poly(vinylidene fluoride) and its copolymers due to their well-defined piezoelectric mechanism and high piezoelectric coefficients that lead to superior magnetoelectric coefficients of >1 V cm−1 Oe−1. This is the current situation despite the potential for other piezoelectric polymers, such as natural biopolymers, to bring unique, added-value properties and functions to magnetoelectric composite devices. Here we demonstrate a cellulose-based magnetoelectric laminate composite that produces considerable magnetoelectric coefficients of ≈1.5 V cm−1 Oe−1, comprising a Fano resonance that is ubiquitous in the field of physics, such as photonics, though never experimentally observed in magnetoelectric composites. The work successfully demonstrates the concept of exploring new advances in using biopolymers in magnetoelectric composites, particularly cellulose, which is increasingly employed as a renewable, low-cost, easily processable and degradable material.
- 22 May 2017
- Published by IOP Publishing in 2D Materials
- Vol. 4 (2) , 025102
Construction of 2D lateral pseudoheterostructures by strain engineering
Two-dimensional (2D) lateral heterostructures host unconventional physical properties due to their controllable band-offset tuning and interfacial sensitive characteristic. The lattice mismatch results in the difficulties to construct the perfect atomic interface in such 2D lateral heterostructures, which in turn limits their desirable properties and performances in applications. In this work, strain-modulated 2D lateral pseudoheterogeneous structures are designed and realized in the single-component 2D BiOBr nanosheets by taking advantage of their strain-sensitive crystal and electronic structures. The pseudoheterogeneous interface without atomic mismatch can be feasibly modulated by local strain distribution, which exhibits similar local electronic band structure of corresponding heterostructures. Significant enhancement in charge separation at the pseudoheterostructure was demonstrated under visible light irradiation, which is given rise to the controllable electronic band alignment across the interface. The construction of the lateral pseudoheterostructure offers a feasible and promising way to build unprecedented 2D systems with exciting properties.
- 22 May 2017
- Published by IOP Publishing in 2D Materials
- Vol. 4 (2) , 025102
Construction of 2D lateral pseudoheterostructures by strain engineering
Two-dimensional (2D) lateral heterostructures host unconventional physical properties due to their controllable band-offset tuning and interfacial sensitive characteristic. The lattice mismatch results in the difficulties to construct the perfect atomic interface in such 2D lateral heterostructures, which in turn limits their desirable properties and performances in applications. In this work, strain-modulated 2D lateral pseudoheterogeneous structures are designed and realized in the single-component 2D BiOBr nanosheets by taking advantage of their strain-sensitive crystal and electronic structures. The pseudoheterogeneous interface without atomic mismatch can be feasibly modulated by local strain distribution, which exhibits similar local electronic band structure of corresponding heterostructures. Significant enhancement in charge separation at the pseudoheterostructure was demonstrated under visible light irradiation, which is given rise to the controllable electronic band alignment across the interface. The construction of the lateral pseudoheterostructure offers a feasible and promising way to build unprecedented 2D systems with exciting properties.
- 1 May 2017
- Published by Elsevier in Electrochimica Acta
- Vol. 235, 348-355
A robust free-standing MoS2/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) film for supercapacitor applications
- 1 May 2017
- Published by Elsevier in Electrochimica Acta
- Vol. 235, 348-355
A robust free-standing MoS2/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) film for supercapacitor applications