Volkan Bozkurt
Research Subjects
Research Interests
Volkan Bozkurt has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Zhenghe Xu
Shenzhen Key Laboratory of Interfacial Science and Engineering of Materials Department of Materials Science and Engineering Southern University of Science and Technology Shenzhen China
5 shared publications J.A. Finch
4 shared publicationsYasar Ucbas
Eskisehir Osmangazi Univ, Fac Engn & Architecture, Dept Min Engn, Eskisehir, Turkiye
3 shared publications- Yasar Ucbas
Eskisehir Osmangazi Univ, Fac Engn & Architecture, Dept Min Engn, TR-26040 Eskisehir, Turkiye
3 shared publications Halil Ipek
2 shared publications- Işıl Tokcan
Eskişehir Osmangazi Üniversitesi
2 shared publications
Latest Publications
- Open Access
- 28 October 2024
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 60 (6)
A comparison of dry and wet grinding on gold-bearing sulphide ore flotation
This study investigates the hypothesis that dry grinding prior to flotation can mitigate the adverse effects of galvanic interactions, improve the selectivity of gold flotation compared to wet grinding, and offer additional benefits due to water scarcity concerns and high water treatment costs. The effects of dry and wet grinding on the flotation behavior of gold-bearing sulphide ore were studied comparatively in terms of flotation test results and pulp chemistry parameters (pH, Eh, and dissolved oxygen). In addition, flotation tests without conditioning were also conducted following dry grinding in an attempt to minimize water contact further. Results demonstrated that dry grinding increased pulp potentials and dissolved oxygen levels, implying more oxidative conditions. Despite a lower mass pull with dry grinding, flotation recoveries and grades of gold and chalcopyrite were comparable to wet grinding, while dry grinding enhanced pyrite flotation at the rougher stage. Notably, flotation without conditioning effectively rejected pyrite and achieved higher grades for gold and chalcopyrite, indicating selective flotation. Therefore, dry grinding before flotation emerges as a viable alternative for gold and chalcopyrite flotation due to its improved selectivity while carefully optimizing flotation strategies and reagents to maximize recoveries.
- 28 October 2024
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 60 (6)
Open AccessA comparison of dry and wet grinding on gold-bearing sulphide ore flotation
This study investigates the hypothesis that dry grinding prior to flotation can mitigate the adverse effects of galvanic interactions, improve the selectivity of gold flotation compared to wet grinding, and offer additional benefits due to water scarcity concerns and high water treatment costs. The effects of dry and wet grinding on the flotation behavior of gold-bearing sulphide ore were studied comparatively in terms of flotation test results and pulp chemistry parameters (pH, Eh, and dissolved oxygen). In addition, flotation tests without conditioning were also conducted following dry grinding in an attempt to minimize water contact further. Results demonstrated that dry grinding increased pulp potentials and dissolved oxygen levels, implying more oxidative conditions. Despite a lower mass pull with dry grinding, flotation recoveries and grades of gold and chalcopyrite were comparable to wet grinding, while dry grinding enhanced pyrite flotation at the rougher stage. Notably, flotation without conditioning effectively rejected pyrite and achieved higher grades for gold and chalcopyrite, indicating selective flotation. Therefore, dry grinding before flotation emerges as a viable alternative for gold and chalcopyrite flotation due to its improved selectivity while carefully optimizing flotation strategies and reagents to maximize recoveries.
- 22 April 2024
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 32 (1) , 1152-1158
SODIUM DITHIONITE AS A PYRITE DEPRESSANT IN GOLD ORE FLOTATION
Sodium dithionite (Na2S2O4) is a widely used reducing agent to control pulp potential (Eh) and pyrite depressant in sulfide ore flotation. In this study, the pyrite depressant effect of sodium dithionite on gold ore flotation was investigated at pH 8 and pH 10.5 comparatively in terms of gold, chalcopyrite, and pyrite recoveries and grades. The presence of sodium dithionite resulted in a drop of approximately 50–70 mV in the Eh values, regardless of the studied pH values, confirming the reducing effect of sodium dithionite. The effects of sodium dithionite on gold and chalcopyrite grades and recoveries were quite limited, especially at pH 10.5. At pH 8, the utilization of sodium dithionite slightly decreased gold and chalcopyrite recovery and grades, while the decrease in pyrite recovery and grades was remarkable. Both pyrite recovery and grade were reduced from 79.5% to 54.7% and 15.3% to 10.7% by the utilization of sodium dithionite at pH 8. In conclusion, it is considered that the selective flotation of gold and chalcopyrite from pyrite can be achieved at a lower pH accompanied by a slightly reduced Eh by the utilization of sodium dithionite.
- 22 April 2024
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 32 (1) , 1152-1158
SODIUM DITHIONITE AS A PYRITE DEPRESSANT IN GOLD ORE FLOTATION
Sodium dithionite (Na2S2O4) is a widely used reducing agent to control pulp potential (Eh) and pyrite depressant in sulfide ore flotation. In this study, the pyrite depressant effect of sodium dithionite on gold ore flotation was investigated at pH 8 and pH 10.5 comparatively in terms of gold, chalcopyrite, and pyrite recoveries and grades. The presence of sodium dithionite resulted in a drop of approximately 50–70 mV in the Eh values, regardless of the studied pH values, confirming the reducing effect of sodium dithionite. The effects of sodium dithionite on gold and chalcopyrite grades and recoveries were quite limited, especially at pH 10.5. At pH 8, the utilization of sodium dithionite slightly decreased gold and chalcopyrite recovery and grades, while the decrease in pyrite recovery and grades was remarkable. Both pyrite recovery and grade were reduced from 79.5% to 54.7% and 15.3% to 10.7% by the utilization of sodium dithionite at pH 8. In conclusion, it is considered that the selective flotation of gold and chalcopyrite from pyrite can be achieved at a lower pH accompanied by a slightly reduced Eh by the utilization of sodium dithionite.
- 4 May 2023
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 59 (2)
The effect of liquid grinding aids on the dry fine grinding of muscovite
This paper investigates the production of a micronized muscovite to a target product size of d 50 ~ 15 µm with a minimum energy consumption to suit the product requirements of the paint industry by a dry grinding process in a laboratory-scale vertical stirred ball mill. A series of batch dry...
- 4 May 2023
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 59 (2)
The effect of liquid grinding aids on the dry fine grinding of muscovite
This paper investigates the production of a micronized muscovite to a target product size of d 50 ~ 15 µm with a minimum energy consumption to suit the product requirements of the paint industry by a dry grinding process in a laboratory-scale vertical stirred ball mill. A series of batch dry...
- 29 April 2023
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 31 (1) , 519-532
INFLUENCES OF GRINDING CONDITIONS ON GALENITE-SPHALERITE FLOTATION KINETICS
Grinding is more than just crushing, it is also a process that causes a chemical reaction on the surface of the mineral. Water used in the grinding process significantly affects the galvanic interaction. Different grinding conditions result in different pulp chemistries. This becomes especially important in sulfide flotation in terms of recovery and selectivity. There are limited studies examining the effects of dry and wet grinding prior to the flotation of sulfide minerals. This study compared the effects of wet and dry grinding on the flotation kinetics of complex Pb-Zn sulfide ore at P80 of 20 and 50 µm grind sizes. Results showed that dry grinding positively affected the sphalerite ore flotation compared to wet grinding in terms of recovery and grade in both galenite and sphalerite rougher flotation stages. Considering that the effect of dry grinding was due to the difference in pulp chemistry, the reasons were explored based on particle morphology, and pulp potentials. The results showed that grinding the same ore under dry and wet conditions significantly affected the flotation performance. In light of the pulp potential measurements, it was determined that the reducing environment obtained in the wet grinding negatively affected the flotation performance, while the oxidizing environment formed during the dry grinding affected the flotation performance positively. This was attributed to the fact that galvanic interactions that occurred during wet grinding were significantly reduced during dry grinding. Hence, better galenite and sphalerite flotation was obtained following dry grinding.
- 29 April 2023
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 31 (1) , 519-532
INFLUENCES OF GRINDING CONDITIONS ON GALENITE-SPHALERITE FLOTATION KINETICS
Grinding is more than just crushing, it is also a process that causes a chemical reaction on the surface of the mineral. Water used in the grinding process significantly affects the galvanic interaction. Different grinding conditions result in different pulp chemistries. This becomes especially important in sulfide flotation in terms of recovery and selectivity. There are limited studies examining the effects of dry and wet grinding prior to the flotation of sulfide minerals. This study compared the effects of wet and dry grinding on the flotation kinetics of complex Pb-Zn sulfide ore at P80 of 20 and 50 µm grind sizes. Results showed that dry grinding positively affected the sphalerite ore flotation compared to wet grinding in terms of recovery and grade in both galenite and sphalerite rougher flotation stages. Considering that the effect of dry grinding was due to the difference in pulp chemistry, the reasons were explored based on particle morphology, and pulp potentials. The results showed that grinding the same ore under dry and wet conditions significantly affected the flotation performance. In light of the pulp potential measurements, it was determined that the reducing environment obtained in the wet grinding negatively affected the flotation performance, while the oxidizing environment formed during the dry grinding affected the flotation performance positively. This was attributed to the fact that galvanic interactions that occurred during wet grinding were significantly reduced during dry grinding. Hence, better galenite and sphalerite flotation was obtained following dry grinding.
- 31 August 2021
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 29 (2) , 224-234
ÖĞÜTME ŞARTLARININ GALENİT FLOTASYONUNA ETKİSİ
Cevherlerin yüzey özellikleri göz önüne alındığında öğütme sürecinde kullanılan suyun galvanik etkileşim üzerinde büyük etkisinin olduğu bilinmektedir. Bu nedenle, öğütme ortamı ve öğütme cihazları sülfürlü minerallerin flotasyon verimi ve seçimliliği üzerinde önemli rol oynamaktadır. Bu kapsamda, bilimsel yazında yer alan kısıtlı sayıdaki çalışmada flotasyon öncesi kuru öğütmenin cevher tipine ve mineral yapısına bağlı olarak yaş öğütmeye kıyasla avantajlarının olabildiği gösterilmiştir. Bu çalışmada, kompleks sülfürlü kurşun-çinko cevheri kullanılmıştır. Tesiste dik değirmen kullanılarak kuru öğütülüp hazırlanmış cevher numuneleri ile laboratuvarda çubuklu değirmen kullanılarak yaş öğütülüp hazırlanan cevher numunelerinin flotasyon performansları karşılaştırmalı olarak incelenmiş ve değerlendirilmiştir. Kuru ve yaş öğütülen numunelerle yapılan flotasyon deneyleri sonucunda, kuru öğütmenin yaş öğütmeye kıyasla, galenit flotasyon performansını gerek verim-tenör gerekse de piritin bastırılması açısından olumlu yönde etkilediği saptanmıştır. Kuru ve yaş öğütme arasında bulunan bu farkın pülp kimyasının farklılığından kaynaklandığı düşünülerek, nedenleri, flotasyon performansı ve pülp potansiyeli parametreleri temel alınarak irdelenmiştir. SEM (Scanning Electron Microscope) görüntüleme analizi kullanılarak, farklı öğütme şartlarında (kuru/yaş) elde edilen numunelerin tane morfolojilerinin karşılaştırılması sonucunda, farklılık gözlemlenmemiştir. Pülpün elektrokimyasal ölçümleri ışığında, çubuklu değirmende yaş öğütme sürecinde oluşan indirgen ortamın flotasyon performansını düşürdüğü belirlenmiştir. Dik değirmende kuru öğütme sırasında oluşan yükseltgen ortamın ise, cevherin flotasyon performansını arttırdığı ancak sfaleritin istenmeyen canlanmasını hızlandırarak seçimliliği azalttığı belirlenmiştir. Çalışmada kullanılan reaktifler, sfaleritin bastırılmasında yeterli olmamıştır. Bulgular, aynı cevherin farklı şartlarda öğütülmesi sonucunda, sistemin pülp kimyasının değişmesinden dolayı, flotasyon performası üzerinde önemli etkiler yarattığını göstermektedir.
- 31 August 2021
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 29 (2) , 224-234
ÖĞÜTME ŞARTLARININ GALENİT FLOTASYONUNA ETKİSİ
Cevherlerin yüzey özellikleri göz önüne alındığında öğütme sürecinde kullanılan suyun galvanik etkileşim üzerinde büyük etkisinin olduğu bilinmektedir. Bu nedenle, öğütme ortamı ve öğütme cihazları sülfürlü minerallerin flotasyon verimi ve seçimliliği üzerinde önemli rol oynamaktadır. Bu kapsamda, bilimsel yazında yer alan kısıtlı sayıdaki çalışmada flotasyon öncesi kuru öğütmenin cevher tipine ve mineral yapısına bağlı olarak yaş öğütmeye kıyasla avantajlarının olabildiği gösterilmiştir. Bu çalışmada, kompleks sülfürlü kurşun-çinko cevheri kullanılmıştır. Tesiste dik değirmen kullanılarak kuru öğütülüp hazırlanmış cevher numuneleri ile laboratuvarda çubuklu değirmen kullanılarak yaş öğütülüp hazırlanan cevher numunelerinin flotasyon performansları karşılaştırmalı olarak incelenmiş ve değerlendirilmiştir. Kuru ve yaş öğütülen numunelerle yapılan flotasyon deneyleri sonucunda, kuru öğütmenin yaş öğütmeye kıyasla, galenit flotasyon performansını gerek verim-tenör gerekse de piritin bastırılması açısından olumlu yönde etkilediği saptanmıştır. Kuru ve yaş öğütme arasında bulunan bu farkın pülp kimyasının farklılığından kaynaklandığı düşünülerek, nedenleri, flotasyon performansı ve pülp potansiyeli parametreleri temel alınarak irdelenmiştir. SEM (Scanning Electron Microscope) görüntüleme analizi kullanılarak, farklı öğütme şartlarında (kuru/yaş) elde edilen numunelerin tane morfolojilerinin karşılaştırılması sonucunda, farklılık gözlemlenmemiştir. Pülpün elektrokimyasal ölçümleri ışığında, çubuklu değirmende yaş öğütme sürecinde oluşan indirgen ortamın flotasyon performansını düşürdüğü belirlenmiştir. Dik değirmende kuru öğütme sırasında oluşan yükseltgen ortamın ise, cevherin flotasyon performansını arttırdığı ancak sfaleritin istenmeyen canlanmasını hızlandırarak seçimliliği azalttığı belirlenmiştir. Çalışmada kullanılan reaktifler, sfaleritin bastırılmasında yeterli olmamıştır. Bulgular, aynı cevherin farklı şartlarda öğütülmesi sonucunda, sistemin pülp kimyasının değişmesinden dolayı, flotasyon performası üzerinde önemli etkiler yarattığını göstermektedir.
- Open Access
- 1 December 2018
- Published by Bilimsel Madencilik Dergisi in Bilimsel Madencilik Dergisi
- Vol. 57 (4) , 225-232
MUSKOVİTİN KARIŞTIRMALI BİLYALI DEĞİRMENDE YAŞ ÖĞÜTÜLMESİNDE ÖĞÜTME YARDIMCILARININ ETKİSİ
Bu çalışmada, muskovitin karıştırmalı bilyalı değirmende mikronize boyuta (d50: 15 μm) yaşöğütülmesinde öğütme yardımcılarının (sodyum hegzametafosfat ve poliakrilik asit sodyum tuzu)etkisi araştırılmıştır. Sonuçlar, özgül enerji tüketimi (kWs/t) ve ürünlerin pülp akış özellikleri dikkatealınarak değerlendirilmiştir. Deney sonuçlarından, 4000 g/t sodyum hegzametafosfat kullanımıile özgül enerji tüketiminden %10,4 ve 1000 g/t poliakrilik asit sodyum tuzu kullanımı ile enerjitüketiminden %9,9 enerji tasarrufu sağlanabileceği görülmüştür. Ayrıca, öğütme yardımcılarınınpülpün kayma gerilmesi ve viskozite değerlerini azalttığı ancak akış tipini (dilatant) değiştirmediğitespit edilmiştir. Pülp akış parametrelerindeki bu azalışın enerji tasarrufunun nedeni olduğusonucuna varılmıştır.
- 1 December 2018
- Published by Bilimsel Madencilik Dergisi in Bilimsel Madencilik Dergisi
- Vol. 57 (4) , 225-232
Open AccessMUSKOVİTİN KARIŞTIRMALI BİLYALI DEĞİRMENDE YAŞ ÖĞÜTÜLMESİNDE ÖĞÜTME YARDIMCILARININ ETKİSİ
Bu çalışmada, muskovitin karıştırmalı bilyalı değirmende mikronize boyuta (d50: 15 μm) yaşöğütülmesinde öğütme yardımcılarının (sodyum hegzametafosfat ve poliakrilik asit sodyum tuzu)etkisi araştırılmıştır. Sonuçlar, özgül enerji tüketimi (kWs/t) ve ürünlerin pülp akış özellikleri dikkatealınarak değerlendirilmiştir. Deney sonuçlarından, 4000 g/t sodyum hegzametafosfat kullanımıile özgül enerji tüketiminden %10,4 ve 1000 g/t poliakrilik asit sodyum tuzu kullanımı ile enerjitüketiminden %9,9 enerji tasarrufu sağlanabileceği görülmüştür. Ayrıca, öğütme yardımcılarınınpülpün kayma gerilmesi ve viskozite değerlerini azalttığı ancak akış tipini (dilatant) değiştirmediğitespit edilmiştir. Pülp akış parametrelerindeki bu azalışın enerji tasarrufunun nedeni olduğusonucuna varılmıştır.
- 1 January 2016
- Published by Elsevier in International Journal of Mineral Processing
- Vol. 146, 46-53
The evaluation of grinding process using artificial neural network
- 1 January 2016
- Published by Elsevier in International Journal of Mineral Processing
- Vol. 146, 46-53
The evaluation of grinding process using artificial neural network
- 13 April 2014
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 49 (6) , 946-956
Separation of Chromite from Serpentine in Fine Sizes using Magnetic Carrier
- 13 April 2014
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 49 (6) , 946-956
Separation of Chromite from Serpentine in Fine Sizes using Magnetic Carrier
- 1 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 344-348
Modeling of grinding process by artificial neural network for calcite mineral
The grindability properties of calcite sample belong to Afyonkarahisar region were investigated at batch grinding conditions based on a kinetic model. The obtained kinetic model parameters were used to estimate the product size distribution by artificial neural networks (ANN). Then, the experimental and neural network prediction results are compared.
- 1 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 344-348
Modeling of grinding process by artificial neural network for calcite mineral
The grindability properties of calcite sample belong to Afyonkarahisar region were investigated at batch grinding conditions based on a kinetic model. The obtained kinetic model parameters were used to estimate the product size distribution by artificial neural networks (ANN). Then, the experimental and neural network prediction results are compared.
- 29 January 2010
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 32 (8) , 727-743
Desulfurization and Deashing of Adiyaman-Gölbaşi Lignite by Flotation
In this study, desulfurization and deashing of Adiyaman-Gölbaşi lignite by the flotation method were studied. For this purpose, the study was performed in three groups. The effects of solid concentration, NaOH, and HCI on the desliming before flotation were investigated in the first group of experiments. The effects of some parameters that markedly influence the effectiveness of flotation, such as grinding time, solid concentration, pH, collector type and amount, depressant type and amount, and frother type and amount on the flotation were investigated in the second group of experiments. The effects of lake water and sea water on the flotation were investigated in the third group of experiments. The influences of the Aegean Sea water and soda lake water on the removal of total sulfur were found to be important.
- 29 January 2010
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 32 (8) , 727-743
Desulfurization and Deashing of Adiyaman-Gölbaşi Lignite by Flotation
In this study, desulfurization and deashing of Adiyaman-Gölbaşi lignite by the flotation method were studied. For this purpose, the study was performed in three groups. The effects of solid concentration, NaOH, and HCI on the desliming before flotation were investigated in the first group of experiments. The effects of some parameters that markedly influence the effectiveness of flotation, such as grinding time, solid concentration, pH, collector type and amount, depressant type and amount, and frother type and amount on the flotation were investigated in the second group of experiments. The effects of lake water and sea water on the flotation were investigated in the third group of experiments. The influences of the Aegean Sea water and soda lake water on the removal of total sulfur were found to be important.