Jia Kong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jia Kong has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Morgan W. Mitchell
ICFO -Institut de Ciencies Fotoniques The Barcelona Institute of Science and Technology 08860 Castelldefels Barcelona Spain
7 shared publications F. Hudelist
Quantum Institute for Light and Atoms, Department of Physics, State Key Laboratory of Precision Spectroscopy, East China Normal University, Shanghai 200062, China
3 shared publicationsRicardo Jiménez-Martínez
ICFO-Institut de Ciencies Fotoniques The Barcelona Institute of Science and Technology 08860 Castelldefels (Barcelona Spain
3 shared publications- Vito Giovanni Lucivero
ICFO–Institut de Ciencies Fotoniques, The Barcelona Institute of Science and Technology, 08860 Castelldefels (Barcelona), Spain
3 shared publications - Weiping Zhang
Department of Physics and Astronomy Shanghai Jiao Tong University 200240 Shanghai P. R. China
3 shared publications - Xiao-Ming Lu
Hangzhou Dianzi University
3 shared publications
Latest Publications
- 1 December 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 24 (6)
Optimized spin estimation in atomic sensors via Kalman filter and smoother
- 1 December 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 24 (6)
Optimized spin estimation in atomic sensors via Kalman filter and smoother
- 30 April 2024
- Published by American Physical Society (APS) in Physical Review A
- Vol. 109 (4) , L040802
Anomalous noise spectra in a spin-exchange-relaxation-free alkali-metal vapor
We perform spin-noise spectroscopy on an unpolarized vapor in the spin-exchange-relaxation-free (SERF) regime. We observe noise spectral distributions that deviate strongly from Lorentzian models that accurately describe lower-density regimes. For example, at magnetic fields of and densities of atoms/ we observe an asymmetric spin-noise distribution in which the resonance line is depleted by about half its power, with the diverted power becoming a broad spectral component that could be mistaken for optical shot noise. The results are in good agreement with recent models accounting for correlations between the ground hyperfine states. We discuss implications for quantum sensing and absolute noise calibration in spin squeezing and entanglement detection. The results suggest similarly anomalous spectra for other noise spectroscopies, when noise mechanisms are not aligned with system dynamics.- 30 April 2024
- Published by American Physical Society (APS) in Physical Review A
- Vol. 109 (4) , L040802
Anomalous noise spectra in a spin-exchange-relaxation-free alkali-metal vapor
We perform spin-noise spectroscopy on an unpolarized vapor in the spin-exchange-relaxation-free (SERF) regime. We observe noise spectral distributions that deviate strongly from Lorentzian models that accurately describe lower-density regimes. For example, at magnetic fields of and densities of atoms/ we observe an asymmetric spin-noise distribution in which the resonance line is depleted by about half its power, with the diverted power becoming a broad spectral component that could be mistaken for optical shot noise. The results are in good agreement with recent models accounting for correlations between the ground hyperfine states. We discuss implications for quantum sensing and absolute noise calibration in spin squeezing and entanglement detection. The results suggest similarly anomalous spectra for other noise spectroscopies, when noise mechanisms are not aligned with system dynamics.- 20 December 2023
- Published by IOP Publishing in Metrologia
- Vol. 61 (1) , 015004
Characterization of laser-pumped Cs-4He atomic magnetometer
In principle, laser-pumped Cs–4He magnetometers can take advantage of the high sensitivity of optically pumped magnetometers and the high accuracy of proton magnetometers. However, insufficient experimental studies have been conducted on the optimization conditions and physics of this type of magnetometer. In this study, we investigate the experimental performance of a laser-pumped Cs–4He magnetometer by optimizing the sensitivity of the excitation pulse settings. We report some dependence relationships that have not been previously reported. The optimal settings under the obtainable experimental conditions in our lab are 34 °C for temperature, 10 μ s for pulse duration, and 67 V and 2.2 V for high- and low-level voltages, respectively, which provide a sensitivity of 26 p T / H z within a frequency of 0.08–0.2 Hz. This study provides a solid reference for further improving the Cs–4He magnetometer, offers the possibility of measuring physical constants more accurately, and provides a deeper understanding of plasma interaction processes.
- 20 December 2023
- Published by IOP Publishing in Metrologia
- Vol. 61 (1) , 015004
Characterization of laser-pumped Cs-4He atomic magnetometer
In principle, laser-pumped Cs–4He magnetometers can take advantage of the high sensitivity of optically pumped magnetometers and the high accuracy of proton magnetometers. However, insufficient experimental studies have been conducted on the optimization conditions and physics of this type of magnetometer. In this study, we investigate the experimental performance of a laser-pumped Cs–4He magnetometer by optimizing the sensitivity of the excitation pulse settings. We report some dependence relationships that have not been previously reported. The optimal settings under the obtainable experimental conditions in our lab are 34 °C for temperature, 10 μ s for pulse duration, and 67 V and 2.2 V for high- and low-level voltages, respectively, which provide a sensitivity of 26 p T / H z within a frequency of 0.08–0.2 Hz. This study provides a solid reference for further improving the Cs–4He magnetometer, offers the possibility of measuring physical constants more accurately, and provides a deeper understanding of plasma interaction processes.
- Open Access
Review of the Applications of Kalman Filtering in Quantum Systems
State variable and parameter estimations are important for signal sensing and feedback control in both traditional engineering systems and quantum systems. The Kalman filter, which is one of the most popular signal recovery techniques in classical systems for decades, has now been connected to the stochastic master equations of linear quantum mechanical systems. Various studies have invested effort on mapping the state evolution of a quantum system into a set of classical filtering equations. However, establishing proper evolution models with symmetry to classical filter equation for quantum systems is not easy. Here, we review works that have successfully built a Kalman filter model for quantum systems and provide an improved method for optimal estimations. We also discuss a practical scenario involving magnetic field estimations in quantum systems, where non-linear Kalman filters could be considered an estimation solution.
Open AccessReview of the Applications of Kalman Filtering in Quantum Systems
State variable and parameter estimations are important for signal sensing and feedback control in both traditional engineering systems and quantum systems. The Kalman filter, which is one of the most popular signal recovery techniques in classical systems for decades, has now been connected to the stochastic master equations of linear quantum mechanical systems. Various studies have invested effort on mapping the state evolution of a quantum system into a set of classical filtering equations. However, establishing proper evolution models with symmetry to classical filter equation for quantum systems is not easy. Here, we review works that have successfully built a Kalman filter model for quantum systems and provide an improved method for optimal estimations. We also discuss a practical scenario involving magnetic field estimations in quantum systems, where non-linear Kalman filters could be considered an estimation solution.
- 15 August 2022
- Published by American Physical Society (APS) in Physical Review A
- Vol. 106 (2) , 023112
Effects of spin-exchange collisions on the fluctuation spectra of hot alkali-metal vapors
We present a first-principles analysis of the noise spectra of alkali-metal vapors in and out of the spin-exchange-relaxation-free (SERF) regime, and we predict nonintuitive features with a potential to further improve the sensitivity of SERF media, and which must be taken into account in their use in quantum optical applications. Studying the process of spin-noise spectroscopy (SNS), we derive analytic formulas for the observable noise spectra, and for the correlation functions among different hyperfine components, which give additional insight into the spin dynamics. The analytic results indicate a variety of distortions of the spin-noise spectrum relative to simpler models, including a broad spectral background that mimics optical shot noise, interference of noise contributions from the two ground-state hyperfine levels, noise reduction at the spin-precession frequency, and “hiding” of spin-noise power that can introduce a systematic error in noise-based calibrations, e.g., for spin-squeezing experiments.
- 15 August 2022
- Published by American Physical Society (APS) in Physical Review A
- Vol. 106 (2) , 023112
Effects of spin-exchange collisions on the fluctuation spectra of hot alkali-metal vapors
We present a first-principles analysis of the noise spectra of alkali-metal vapors in and out of the spin-exchange-relaxation-free (SERF) regime, and we predict nonintuitive features with a potential to further improve the sensitivity of SERF media, and which must be taken into account in their use in quantum optical applications. Studying the process of spin-noise spectroscopy (SNS), we derive analytic formulas for the observable noise spectra, and for the correlation functions among different hyperfine components, which give additional insight into the spin dynamics. The analytic results indicate a variety of distortions of the spin-noise spectrum relative to simpler models, including a broad spectral background that mimics optical shot noise, interference of noise contributions from the two ground-state hyperfine levels, noise reduction at the spin-precession frequency, and “hiding” of spin-noise power that can introduce a systematic error in noise-based calibrations, e.g., for spin-squeezing experiments.
- 1 May 2022
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 93 (5) , 053001
Modulation-free portable laser frequency and power stabilization system
The performance of laser-based instruments heavily depends on the stability of their laser source. Some instruments, such as the Cs–4He magnetometer, even require the frequency stabilization and the power stabilization at the same time. In this work, we design a double-locking system with a fiber-coupled output on a small bread board and apply it to the pump laser of a Cs–4He magnetometer. By carefully choosing the stabilization methods, we significantly improve the long-term simultaneous stability of frequency and power of the pump laser. The laser frequency drifts in 2 h are reduced from 100 to 10 MHz. For 10 h continuous measurements, their Allan deviation obtains about two orders of magnitude improvement for the averaging time larger than 200 s and reaches σ(τ) = 1.57 × 10−9 with a 200 s averaging time. The laser power stability for 1.8 h also obtains two orders of magnitude improvement from 3.22% to 0.031%, and its power noise reaches a level that is very close to the electronic noise of the detector. Applying this stabilization system to the pump laser of a fiber-coupled Cs–4He magnetometer, its magnetic sensor noise is significantly reduced from 0.158 to 0.009 nT, which is a reasonable noise for magnetic field detection. With this on-board design of the laser stabilization system, it is more convenient to transform the magnetometer into an outdoor device.
- 1 May 2022
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 93 (5) , 053001
Modulation-free portable laser frequency and power stabilization system
The performance of laser-based instruments heavily depends on the stability of their laser source. Some instruments, such as the Cs–4He magnetometer, even require the frequency stabilization and the power stabilization at the same time. In this work, we design a double-locking system with a fiber-coupled output on a small bread board and apply it to the pump laser of a Cs–4He magnetometer. By carefully choosing the stabilization methods, we significantly improve the long-term simultaneous stability of frequency and power of the pump laser. The laser frequency drifts in 2 h are reduced from 100 to 10 MHz. For 10 h continuous measurements, their Allan deviation obtains about two orders of magnitude improvement for the averaging time larger than 200 s and reaches σ(τ) = 1.57 × 10−9 with a 200 s averaging time. The laser power stability for 1.8 h also obtains two orders of magnitude improvement from 3.22% to 0.031%, and its power noise reaches a level that is very close to the electronic noise of the detector. Applying this stabilization system to the pump laser of a fiber-coupled Cs–4He magnetometer, its magnetic sensor noise is significantly reduced from 0.158 to 0.009 nT, which is a reasonable noise for magnetic field detection. With this on-board design of the laser stabilization system, it is more convenient to transform the magnetometer into an outdoor device.
- 20 January 2022
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 128 (3) , 033601
SU(2)-in-SU(1,1) Nested Interferometer for High Sensitivity, Loss-Tolerant Quantum Metrology
We present experimental and theoretical results on a new interferometer topology that nests a SU(2) interferometer, e.g., a Mach-Zehnder or Michelson interferometer, inside a SU(1,1) interferometer, i.e., a Mach-Zehnder interferometer with parametric amplifiers in place of beam splitters. This SU(2)-in-SU(1,1) nested interferometer (SISNI) simultaneously achieves a high signal-to-noise ratio (SNR), sensitivity beyond the standard quantum limit (SQL) and tolerance to photon losses external to the interferometer, e.g., in detectors. We implement a SISNI using parametric amplification by four-wave mixing (FWM) in Rb vapor and a laser-fed Mach-Zehnder SU(2) interferometer. We observe path-length sensitivity with SNR 2.2 dB beyond the SQL at power levels (and thus SNR) 2 orders of magnitude beyond those of previous loss-tolerant interferometers. We find experimentally the optimal FWM gains and find agreement with a minimal quantum noise model for the FWM process. The results suggest ways to boost the in-practice sensitivity of high-power interferometers, e.g., gravitational wave interferometers, and may enable high-sensitivity, quantum-enhanced interferometry at wavelengths for which efficient detectors are not available.
- 20 January 2022
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 128 (3) , 033601
SU(2)-in-SU(1,1) Nested Interferometer for High Sensitivity, Loss-Tolerant Quantum Metrology
We present experimental and theoretical results on a new interferometer topology that nests a SU(2) interferometer, e.g., a Mach-Zehnder or Michelson interferometer, inside a SU(1,1) interferometer, i.e., a Mach-Zehnder interferometer with parametric amplifiers in place of beam splitters. This SU(2)-in-SU(1,1) nested interferometer (SISNI) simultaneously achieves a high signal-to-noise ratio (SNR), sensitivity beyond the standard quantum limit (SQL) and tolerance to photon losses external to the interferometer, e.g., in detectors. We implement a SISNI using parametric amplification by four-wave mixing (FWM) in Rb vapor and a laser-fed Mach-Zehnder SU(2) interferometer. We observe path-length sensitivity with SNR 2.2 dB beyond the SQL at power levels (and thus SNR) 2 orders of magnitude beyond those of previous loss-tolerant interferometers. We find experimentally the optimal FWM gains and find agreement with a minimal quantum noise model for the FWM process. The results suggest ways to boost the in-practice sensitivity of high-power interferometers, e.g., gravitational wave interferometers, and may enable high-sensitivity, quantum-enhanced interferometry at wavelengths for which efficient detectors are not available.
- 2 November 2021
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 127 (19) , 193601
Squeezed-Light Enhancement and Backaction Evasion in a High Sensitivity Optically Pumped Magnetometer
We study the effect of optical polarization squeezing on the performance of a sensitive, quantum-noise-limited optically pumped magnetometer. We use Bell-Bloom (BB) optical pumping to excite a vapor containing and Faraday rotation to detect spin precession. The sub- sensitivity is limited by spin projection noise (photon shot noise) at low (high) frequencies. Probe polarization squeezing both improves high-frequency sensitivity and increases measurement bandwidth, with no loss of sensitivity at any frequency, a direct demonstration of the evasion of measurement backaction noise. We provide a model for the quantum noise dynamics of the BB magnetometer, including spin projection noise, probe polarization noise, and measurement backaction effects. The theory shows how polarization squeezing reduces optical noise, while measurement backaction due to the accompanying ellipticity antisqueezing is shunted into the unmeasured spin component. The method is compatible with high-density and multipass techniques that reach extreme sensitivity.- 2 November 2021
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 127 (19) , 193601
Squeezed-Light Enhancement and Backaction Evasion in a High Sensitivity Optically Pumped Magnetometer
We study the effect of optical polarization squeezing on the performance of a sensitive, quantum-noise-limited optically pumped magnetometer. We use Bell-Bloom (BB) optical pumping to excite a vapor containing and Faraday rotation to detect spin precession. The sub- sensitivity is limited by spin projection noise (photon shot noise) at low (high) frequencies. Probe polarization squeezing both improves high-frequency sensitivity and increases measurement bandwidth, with no loss of sensitivity at any frequency, a direct demonstration of the evasion of measurement backaction noise. We provide a model for the quantum noise dynamics of the BB magnetometer, including spin projection noise, probe polarization noise, and measurement backaction effects. The theory shows how polarization squeezing reduces optical noise, while measurement backaction due to the accompanying ellipticity antisqueezing is shunted into the unmeasured spin component. The method is compatible with high-density and multipass techniques that reach extreme sensitivity.- Open Access
Measurement-induced nonlocal entanglement in a hot, strongly-interacting atomic system
Quantum technologies use entanglement to outperform classical technologies, and often employ strong cooling and isolation to protect entangled entities from decoherence by random interactions. Here we show that the opposite strategy - promoting random interactions - can help generate and preserve entanglement. We use optical quantum non-demolition measurement to produce entanglement in a hot alkali vapor, in a regime dominated by random spin-exchange collisions. We use Bayesian statistics and spin-squeezing inequalities to show that at least $1.52(4)\times 10^{13}$ of the $5.32(12) \times 10^{13}$ participating atoms enter into singlet-type entangled states, which persist for tens of spin-thermalization times and span thousands of times the nearest-neighbor distance. The results show that high temperatures and strong random interactions need not destroy many-body quantum coherence, that collective measurement can produce very complex entangled states, and that the hot, strongly-interacting media now in use for extreme atomic sensing are well suited for sensing beyond the standard quantum limit.Open AccessMeasurement-induced nonlocal entanglement in a hot, strongly-interacting atomic system
Quantum technologies use entanglement to outperform classical technologies, and often employ strong cooling and isolation to protect entangled entities from decoherence by random interactions. Here we show that the opposite strategy - promoting random interactions - can help generate and preserve entanglement. We use optical quantum non-demolition measurement to produce entanglement in a hot alkali vapor, in a regime dominated by random spin-exchange collisions. We use Bayesian statistics and spin-squeezing inequalities to show that at least $1.52(4)\times 10^{13}$ of the $5.32(12) \times 10^{13}$ participating atoms enter into singlet-type entangled states, which persist for tens of spin-thermalization times and span thousands of times the nearest-neighbor distance. The results show that high temperatures and strong random interactions need not destroy many-body quantum coherence, that collective measurement can produce very complex entangled states, and that the hot, strongly-interacting media now in use for extreme atomic sensing are well suited for sensing beyond the standard quantum limit. - Open Access
- 15 May 2020
- Published by Springer Nature in Nature Communications
- Vol. 11 (1) , 1-9
Measurement-induced, spatially-extended entanglement in a hot, strongly-interacting atomic system
Quantum technologies use entanglement to outperform classical technologies, and often employ strong cooling and isolation to protect entangled entities from decoherence by random interactions. Here we show that the opposite strategy—promoting random interactions—can help generate and preserve entanglement. We use optical quantum non-demolition measurement to produce entanglement in a hot alkali vapor, in a regime dominated by random spin-exchange collisions. We use Bayesian statistics and spin-squeezing inequalities to show that at least 1.52(4) × 1013 of the 5.32(12) × 1013 participating atoms enter into singlet-type entangled states, which persist for tens of spin-thermalization times and span thousands of times the nearest-neighbor distance. The results show that high temperatures and strong random interactions need not destroy many-body quantum coherence, that collective measurement can produce very complex entangled states, and that the hot, strongly-interacting media now in use for extreme atomic sensing are well suited for sensing beyond the standard quantum limit.
- 15 May 2020
- Published by Springer Nature in Nature Communications
- Vol. 11 (1) , 1-9
Open AccessMeasurement-induced, spatially-extended entanglement in a hot, strongly-interacting atomic system
Quantum technologies use entanglement to outperform classical technologies, and often employ strong cooling and isolation to protect entangled entities from decoherence by random interactions. Here we show that the opposite strategy—promoting random interactions—can help generate and preserve entanglement. We use optical quantum non-demolition measurement to produce entanglement in a hot alkali vapor, in a regime dominated by random spin-exchange collisions. We use Bayesian statistics and spin-squeezing inequalities to show that at least 1.52(4) × 1013 of the 5.32(12) × 1013 participating atoms enter into singlet-type entangled states, which persist for tens of spin-thermalization times and span thousands of times the nearest-neighbor distance. The results show that high temperatures and strong random interactions need not destroy many-body quantum coherence, that collective measurement can produce very complex entangled states, and that the hot, strongly-interacting media now in use for extreme atomic sensing are well suited for sensing beyond the standard quantum limit.