Yafei Fan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yafei Fan has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Nicola Pinna
Department of Chemistry and The Center for the Science of Materials Berlin, Humboldt-Universität zu Berlin, Berlin, Germany
9 shared publications - Enza Fazio
University of Messina
4 shared publications - Fabiola Pantò
Istituto di Tecnologie Avanzate per l’Energia (ITAE) del Consiglio Nazionale delle Ricerche (CNR), 98126 Messina, Italy
4 shared publications Patrizia Frontera
Dipartimento di Ingegneria Civile dell'Energia, dell'Ambiente e dei Materiali (DICEAM) Università “Mediterranea” 89122 Reggio Calabria Italy
4 shared publicationsPierluigi Antonucci
Dipartimento di Ingegneria Civile dell'Energia, dell'Ambiente e dei Materiali (DICEAM) Università “Mediterranea” 89122 Reggio Calabria Italy
4 shared publicationsQiang Cai
Key Laboratory for Advanced Materials of Ministry of Education and Department of Materials Science and Engineering Tsinghua University Beijing 100084 People's Republic of China
4 shared publications
Latest Publications
- 15 August 2018
- Published by Springer Nature in Journal of Nanoparticle Research
- Vol. 20 (8) , 216
Effect of passivating Al2O3 thin films on MnO2/carbon nanotube composite lithium-ion battery anodes
- 15 August 2018
- Published by Springer Nature in Journal of Nanoparticle Research
- Vol. 20 (8) , 216
Effect of passivating Al2O3 thin films on MnO2/carbon nanotube composite lithium-ion battery anodes
- 7 August 2018
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 1 (9) , 4554-4563
Optimization of the Activity of Ni-Based Nanostructures for the Oxygen Evolution Reaction
- 7 August 2018
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 1 (9) , 4554-4563
Optimization of the Activity of Ni-Based Nanostructures for the Oxygen Evolution Reaction
- 31 May 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (23) , 19656-19663
Sea-Sponge-like Structure of Nano-Fe3O4 on Skeleton-C with Long Cycle Life under High Rate for Li-Ion Batteries
To meet the demands of long cycle life under high rate for lithium-ion batteries, the advancement of anode materials with stable structural properties is necessarily demanded. Such promotion needs to design reasonable structure to facilitate the transportation of electron and lithium ions (Li+). Herein, a novel C/Fe3O4 sea-sponge-like structure was synthesized by ultrasonic spray pyrolysis following thermal decomposition process. On the basis of sea-sponge carbon (SSC) excellences in electronic conductivity and short Li+ diffusion pathway, nano-Fe3O4 anchored on stable SSC skeleton can deliver high electrochemical performance with long cycle life under high rate. During electrochemical cycling, well-dispersed nano-Fe3O4 in ∼6 nm not only averts excessive pulverization and is enveloped by solid electrolyte interphase film, but also increases Li+ diffusion efficiency. The much improved electrochemical properties showed a capacity of around 460 mAh g–1 at a high rate of 1.5C with a retention rate of 93%, which is maintained without degradation up to 1000 cycles (1C = 1000 mA g–1).
- 31 May 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (23) , 19656-19663
Sea-Sponge-like Structure of Nano-Fe3O4 on Skeleton-C with Long Cycle Life under High Rate for Li-Ion Batteries
To meet the demands of long cycle life under high rate for lithium-ion batteries, the advancement of anode materials with stable structural properties is necessarily demanded. Such promotion needs to design reasonable structure to facilitate the transportation of electron and lithium ions (Li+). Herein, a novel C/Fe3O4 sea-sponge-like structure was synthesized by ultrasonic spray pyrolysis following thermal decomposition process. On the basis of sea-sponge carbon (SSC) excellences in electronic conductivity and short Li+ diffusion pathway, nano-Fe3O4 anchored on stable SSC skeleton can deliver high electrochemical performance with long cycle life under high rate. During electrochemical cycling, well-dispersed nano-Fe3O4 in ∼6 nm not only averts excessive pulverization and is enveloped by solid electrolyte interphase film, but also increases Li+ diffusion efficiency. The much improved electrochemical properties showed a capacity of around 460 mAh g–1 at a high rate of 1.5C with a retention rate of 93%, which is maintained without degradation up to 1000 cycles (1C = 1000 mA g–1).
- 28 May 2018
- Published by Wiley in ChemElectroChem
- Vol. 5 (14) , 2010-2018
Polarization Resistance‐Free Mn3O4‐Based Electrocatalysts for the Oxygen Reduction Reaction
Transition metal oxides have been proposed as a possible replacement of platinum for the electrocatalytic oxygen reduction reaction (ORR). However, as a result of the low intrinsic conductivity, an application in electrocatalysis is challenging. In this work, we demonstrate that atomic layer deposition (ALD) is capable to overcome this problem by coating conductive carbon nanotubes substrates with a conformal Mn3O4 layer of just few‐nm in thickness. The deposition parameters have been optimized in terms of thickness and crystallite sizes to produce a material exhibiting catalytic efficiency close to the one of carbon‐supported Pt particles and low polarization costs. The current densities recorded in linear sweep voltammetry prove that the Mn3O4 coating leads to a substantial increase of the catalytic efficiency, compared to uncoated carbon nanotubes, and was also higher than other manganese‐based catalysts reported so far. The sample prepared from only 50 ALD cycles (e. g. coating thickness of ∼2 nm) shows the best compromise between catalytic efficiency, with an onset potential at 0.867 V (vs. RHE), and good conductivity of the electrode materials minimizing polarization. Indeed, the Tafel plots exhibit a similar slope than Pt/C demonstrating that the Mn3O4/CNTs reduce oxygen in a one‐step four electrons mechanism and with a similar kinetics as Pt‐based electrocatalysts. Moreover, the current density keeps at 80 % even after 12 h at 0.58 V displaying a higher stability than Pt‐based catalysts. These findings are attributed to the few nm‐thick conformal and catalytic active coating obtained by atomic layer deposition, which also protects the underneath CNT substrate from corrosion.
- 28 May 2018
- Published by Wiley in ChemElectroChem
- Vol. 5 (14) , 2010-2018
Polarization Resistance‐Free Mn3O4‐Based Electrocatalysts for the Oxygen Reduction Reaction
Transition metal oxides have been proposed as a possible replacement of platinum for the electrocatalytic oxygen reduction reaction (ORR). However, as a result of the low intrinsic conductivity, an application in electrocatalysis is challenging. In this work, we demonstrate that atomic layer deposition (ALD) is capable to overcome this problem by coating conductive carbon nanotubes substrates with a conformal Mn3O4 layer of just few‐nm in thickness. The deposition parameters have been optimized in terms of thickness and crystallite sizes to produce a material exhibiting catalytic efficiency close to the one of carbon‐supported Pt particles and low polarization costs. The current densities recorded in linear sweep voltammetry prove that the Mn3O4 coating leads to a substantial increase of the catalytic efficiency, compared to uncoated carbon nanotubes, and was also higher than other manganese‐based catalysts reported so far. The sample prepared from only 50 ALD cycles (e. g. coating thickness of ∼2 nm) shows the best compromise between catalytic efficiency, with an onset potential at 0.867 V (vs. RHE), and good conductivity of the electrode materials minimizing polarization. Indeed, the Tafel plots exhibit a similar slope than Pt/C demonstrating that the Mn3O4/CNTs reduce oxygen in a one‐step four electrons mechanism and with a similar kinetics as Pt‐based electrocatalysts. Moreover, the current density keeps at 80 % even after 12 h at 0.58 V displaying a higher stability than Pt‐based catalysts. These findings are attributed to the few nm‐thick conformal and catalytic active coating obtained by atomic layer deposition, which also protects the underneath CNT substrate from corrosion.
- 18 April 2018
- Published by Wiley in Advanced Functional Materials
- Vol. 28 (23)
Are Electrospun Fibrous Membranes Relevant Electrode Materials for Li‐Ion Batteries? The Case of the C/Ge/GeO2 Composite Fibers
Self‐supporting paper‐like membranes consisting of carbon/germanium dioxide (C/GeO2) fibers are prepared via electrospinning of solutions with different germanium load (2.50−4.25 wt%), followed by carbonization at 550−700 °C, and are evaluated as anode materials in lithium ion batteries. The investigation of the physicochemical properties of the membranes by several characterization techniques shows that, as expected, with increasing carbonization temperature better graphitized and less nitrogen‐rich C fibers are obtained, containing Ge0 and/or reduced oxide phases along with GeO2 nanoparticles. These characteristics, combined with the cold pressing of the as‐spun membrane that noticeably reduces the hollow space within the fibres giving rise to a more compact and tight structure, lead to initial discharge volumetric capacities (≈1390–3580 mAh cm−3) much higher than commercial graphite anodes. In particular, the membrane prepared from solution with 4.25 wt% Ge‐load by cold‐pressing and carbonization at 700 °C, is able to deliver ≈1500 mAh cm−3 after 50 cycles at 50 mA g−1 with a Coulombic efficiency close to 100%. Nevertheless, the anodes exhibit poor rate capability. This is because the carbonization at high temperature promotes outward diffusion and subsequent coalescence of Ge‐clusters in larger particles, with the structure of the fibers made fragile by the formation of voids within them.
- 18 April 2018
- Published by Wiley in Advanced Functional Materials
- Vol. 28 (23)
Are Electrospun Fibrous Membranes Relevant Electrode Materials for Li‐Ion Batteries? The Case of the C/Ge/GeO2 Composite Fibers
Self‐supporting paper‐like membranes consisting of carbon/germanium dioxide (C/GeO2) fibers are prepared via electrospinning of solutions with different germanium load (2.50−4.25 wt%), followed by carbonization at 550−700 °C, and are evaluated as anode materials in lithium ion batteries. The investigation of the physicochemical properties of the membranes by several characterization techniques shows that, as expected, with increasing carbonization temperature better graphitized and less nitrogen‐rich C fibers are obtained, containing Ge0 and/or reduced oxide phases along with GeO2 nanoparticles. These characteristics, combined with the cold pressing of the as‐spun membrane that noticeably reduces the hollow space within the fibres giving rise to a more compact and tight structure, lead to initial discharge volumetric capacities (≈1390–3580 mAh cm−3) much higher than commercial graphite anodes. In particular, the membrane prepared from solution with 4.25 wt% Ge‐load by cold‐pressing and carbonization at 700 °C, is able to deliver ≈1500 mAh cm−3 after 50 cycles at 50 mA g−1 with a Coulombic efficiency close to 100%. Nevertheless, the anodes exhibit poor rate capability. This is because the carbonization at high temperature promotes outward diffusion and subsequent coalescence of Ge‐clusters in larger particles, with the structure of the fibers made fragile by the formation of voids within them.
- 1 January 2018
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 43 (2) , 1036
Corrigendum to “Electrospun C/GeO2 paper-like electrodes for flexible Li-ion batteries” [Int J Hydrogen Energy 42 (2017) 28102–28112]
- 1 January 2018
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 43 (2) , 1036
Corrigendum to “Electrospun C/GeO2 paper-like electrodes for flexible Li-ion batteries” [Int J Hydrogen Energy 42 (2017) 28102–28112]
- 1 November 2017
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 42 (46) , 28102-28112
Electrospun C/GeO 2 paper-like electrodes for flexible Li-ion batteries
- 1 November 2017
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 42 (46) , 28102-28112
Electrospun C/GeO 2 paper-like electrodes for flexible Li-ion batteries
- 25 October 2016
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 163 (14) , A2930-A2937
Are Electrospun Carbon/Metal Oxide Composite Fibers Relevant Electrode Materials for Li-Ion Batteries?
Self-standing and flexible paper-like electrodes consisting of nano-sized Co3O4 nanoparticles encapsulated in nitrogen-doped graphite-like carbon fibers are synthesized by electrospinning followed by thermal treatment. Several studies have recently reported that encapsulating nano-sized metal oxides that display conversion reaction, such as manganese, iron and cobalt oxides, within the three-dimensional network of electrospun carbon fibers allows to remarkably improve the performances of lithium-ion batteries. In the present work, we challenge these reports with a study based on the optimization of the preparation and post-synthesis treatment parameters, and a very precise characterization of the structural, morphological and chemical properties of the composite materials leading to clear structure-electrochemical properties correlations. In particular, it is found that the electrochemical properties of a physical mixture of cobalt oxide nanoparticles and electrospun carbon nanofibers are equivalent to the ones of the electrospun nanocomposites, proving that the benefit of electrospun metal oxide-carbon nanocomposites is limited and that the “enhanced properties” claimed in the literature arise from imprudent comparisons.
- 25 October 2016
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 163 (14) , A2930-A2937
Are Electrospun Carbon/Metal Oxide Composite Fibers Relevant Electrode Materials for Li-Ion Batteries?
Self-standing and flexible paper-like electrodes consisting of nano-sized Co3O4 nanoparticles encapsulated in nitrogen-doped graphite-like carbon fibers are synthesized by electrospinning followed by thermal treatment. Several studies have recently reported that encapsulating nano-sized metal oxides that display conversion reaction, such as manganese, iron and cobalt oxides, within the three-dimensional network of electrospun carbon fibers allows to remarkably improve the performances of lithium-ion batteries. In the present work, we challenge these reports with a study based on the optimization of the preparation and post-synthesis treatment parameters, and a very precise characterization of the structural, morphological and chemical properties of the composite materials leading to clear structure-electrochemical properties correlations. In particular, it is found that the electrochemical properties of a physical mixture of cobalt oxide nanoparticles and electrospun carbon nanofibers are equivalent to the ones of the electrospun nanocomposites, proving that the benefit of electrospun metal oxide-carbon nanocomposites is limited and that the “enhanced properties” claimed in the literature arise from imprudent comparisons.
- 12 August 2016
- Published by Wiley in Advanced Materials Interfaces
- Vol. 3 (21) , 1600313
Coating of Vertically Aligned Carbon Nanotubes by a Novel Manganese Oxide Atomic Layer Deposition Process for Binder‐Free Hybrid Capacitors
A novel atomic layer deposition process of manganese oxide from methylcyclopentadienyl manganese tricarbonyl and ozone has been developed. It is used to coat vertically aligned carbon nanotubes (VACNTs) grown on a conductive Inconel substrate in order to produce a 3D array of metal oxide‐carbon nanotube electrode. Electron microscopy studies show that a conformal polycrystalline film can be deposited on the VACNTs arrays. X‐ray diffraction, small area electron diffraction, and X‐ray photoelectron spectroscopy analysis determine the formation of hausmannite (Mn3O4). The electrochemical properties of the as‐prepared VACNTs/Mn3O4 nanocomposite electrodes are studied using cyclic voltammetry, galvanostatic charge and discharge cycling in 1 m Na2SO4 aqueous electrolyte. Capacitances as high as 78.62 mF cm−2 at 5 mV s−1 are demonstrated which is one order of magnitude higher than that of pristine VACNTs. In addition, the as‐prepared VACNTs/Mn3O4 nanocomposite electrode showed a good reversibility and cycling stability.
- 12 August 2016
- Published by Wiley in Advanced Materials Interfaces
- Vol. 3 (21) , 1600313
Coating of Vertically Aligned Carbon Nanotubes by a Novel Manganese Oxide Atomic Layer Deposition Process for Binder‐Free Hybrid Capacitors
A novel atomic layer deposition process of manganese oxide from methylcyclopentadienyl manganese tricarbonyl and ozone has been developed. It is used to coat vertically aligned carbon nanotubes (VACNTs) grown on a conductive Inconel substrate in order to produce a 3D array of metal oxide‐carbon nanotube electrode. Electron microscopy studies show that a conformal polycrystalline film can be deposited on the VACNTs arrays. X‐ray diffraction, small area electron diffraction, and X‐ray photoelectron spectroscopy analysis determine the formation of hausmannite (Mn3O4). The electrochemical properties of the as‐prepared VACNTs/Mn3O4 nanocomposite electrodes are studied using cyclic voltammetry, galvanostatic charge and discharge cycling in 1 m Na2SO4 aqueous electrolyte. Capacitances as high as 78.62 mF cm−2 at 5 mV s−1 are demonstrated which is one order of magnitude higher than that of pristine VACNTs. In addition, the as‐prepared VACNTs/Mn3O4 nanocomposite electrode showed a good reversibility and cycling stability.
- Open Access
- 27 July 2015
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 3 (34) , 17804-17810
Catalyst-free growth of carbon nanotube arrays directly on Inconel® substrates for electrochemical carbon-based electrodes
Vertically aligned carbon nanotubes grown directly onto a metallic substrate without external catalyst can be used as the active electrode material and the current collector, respectively.
- 27 July 2015
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 3 (34) , 17804-17810
Open AccessCatalyst-free growth of carbon nanotube arrays directly on Inconel® substrates for electrochemical carbon-based electrodes
Vertically aligned carbon nanotubes grown directly onto a metallic substrate without external catalyst can be used as the active electrode material and the current collector, respectively.