Meenu Kaushik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Meenu Kaushik has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Vishant Gahlaut
Banasthali Vidyapith
8 shared publications - A. Mercy Latha
Microwave Tubes Division, Council for Scientific and Industrial Research, Central Electronics Engineering Research Institute, Pilani, India
4 shared publications - Bhupender Singh
Department of Water Supply and Environmental Engineering, Arba Minch University, Arba Minch, Ethiopia
4 shared publications - Anshuman Shastri
Banasthali Vidyapith
3 shared publications - Poonam Tiwari
Department of Electrical Engineering, Indian Institute of Technology Indore, Indore, Madhya Pradesh, India
3 shared publications Ayan Kumar Bandyopadhyay
CSIR-Central Electronics Engineering Research Institiute,Pilani,Rajasthan,India
2 shared publications
Latest Publications
- Open Access
- 1 November 2026
- Published by AIP Publishing in AIP Advances
- Vol. 16 (11)
Novel design of output waveguide coupler for high-power Ka-band helix traveling wave tube
A novel design of waveguide output coupler for helix traveling wave tubes operating in the Ka-band satellite downlink frequency range has been proposed. To achieve effective RF coupling between the slow-wave structure and the external waveguide, a multi-section impedance transformer approach has been adopted. Quarter-wavelength matching sections, based on transmission-line theory, gradually convert the source impedance to the load characteristic impedance, ensuring maximum power transfer. In contrast to the traditional designs, here, the center conductor dimension has been maintained uniform and the outer conductor dimensions have been modified in each quarter-wavelength coaxial section for smooth impedance transition and effective power coupling. The geometry of the coupler has been systematically analyzed using a 3-D electromagnetic simulator. It has been demonstrated that the designed coaxial coupler to the waveguide coupler, which employs the standard WR-42 waveguide, acts as a high power ∼300 W and low-loss guiding structure. It also helps in avoiding dielectric breakdown and thermal melting because waveguides have no inner conductor as in coaxial couplers. In order to guarantee consistent RF performance under practical operating conditions, extensive geometric sensitivity analysis has been performed on all the geometric parameters, which enables setting the dimensional tolerances during fabrication at acceptable structural deformation levels during the tube operation.
- 1 November 2026
- Published by AIP Publishing in AIP Advances
- Vol. 16 (11)
Open AccessNovel design of output waveguide coupler for high-power Ka-band helix traveling wave tube
A novel design of waveguide output coupler for helix traveling wave tubes operating in the Ka-band satellite downlink frequency range has been proposed. To achieve effective RF coupling between the slow-wave structure and the external waveguide, a multi-section impedance transformer approach has been adopted. Quarter-wavelength matching sections, based on transmission-line theory, gradually convert the source impedance to the load characteristic impedance, ensuring maximum power transfer. In contrast to the traditional designs, here, the center conductor dimension has been maintained uniform and the outer conductor dimensions have been modified in each quarter-wavelength coaxial section for smooth impedance transition and effective power coupling. The geometry of the coupler has been systematically analyzed using a 3-D electromagnetic simulator. It has been demonstrated that the designed coaxial coupler to the waveguide coupler, which employs the standard WR-42 waveguide, acts as a high power ∼300 W and low-loss guiding structure. It also helps in avoiding dielectric breakdown and thermal melting because waveguides have no inner conductor as in coaxial couplers. In order to guarantee consistent RF performance under practical operating conditions, extensive geometric sensitivity analysis has been performed on all the geometric parameters, which enables setting the dimensional tolerances during fabrication at acceptable structural deformation levels during the tube operation.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 54 (10) , 5111-5117
Miniaturized Conventional Collector for Next-Generation High-Efficiency TWTs
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 54 (10) , 5111-5117
Miniaturized Conventional Collector for Next-Generation High-Efficiency TWTs
- 15 July 2026
- Published by Taylor & Francis
- p. 95-111
Computational approximation techniques for evaluating electromagnetic quantities
- 15 July 2026
- Published by Taylor & Francis
- p. 95-111
Computational approximation techniques for evaluating electromagnetic quantities
- Open Access
- 1 September 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (9)
Design and development of radial input cavity with coupler for inductive output tube
This paper presents the design and electromagnetic analysis of a radial-type input cavity structure for a 350 MHz high-power Inductive Output Tube (IOT), with a focus on developing and validating a novel analytical design methodology. Unlike conventional approaches that rely extensively on numerical simulations, the proposed analytical framework enables precise cavity design and optimization with minimal dependence on computationally intensive tools. This methodology offers enhanced design flexibility, faster prototyping, and deeper physical insight into the cavity behavior. The input cavity, along with a coaxial loop coupler engineered for efficient power injection and minimal reflection, was initially designed using the proposed analytical approach and subsequently verified through full-wave electromagnetic simulations and experimental cold-test measurements. A comprehensive sensitivity analysis was conducted to determine permissible mechanical tolerances in the fabricated structure. The fabricated prototype demonstrated excellent agreement with both analytical and simulated results, thereby validating the accuracy and robustness of the proposed design methodology. This work contributes a practical and efficient alternative to simulation-driven design for high-efficiency, high-power vacuum electron devices, particularly beneficial for the development of next-generation IOTs.
- 1 September 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (9)
Open AccessDesign and development of radial input cavity with coupler for inductive output tube
This paper presents the design and electromagnetic analysis of a radial-type input cavity structure for a 350 MHz high-power Inductive Output Tube (IOT), with a focus on developing and validating a novel analytical design methodology. Unlike conventional approaches that rely extensively on numerical simulations, the proposed analytical framework enables precise cavity design and optimization with minimal dependence on computationally intensive tools. This methodology offers enhanced design flexibility, faster prototyping, and deeper physical insight into the cavity behavior. The input cavity, along with a coaxial loop coupler engineered for efficient power injection and minimal reflection, was initially designed using the proposed analytical approach and subsequently verified through full-wave electromagnetic simulations and experimental cold-test measurements. A comprehensive sensitivity analysis was conducted to determine permissible mechanical tolerances in the fabricated structure. The fabricated prototype demonstrated excellent agreement with both analytical and simulated results, thereby validating the accuracy and robustness of the proposed design methodology. This work contributes a practical and efficient alternative to simulation-driven design for high-efficiency, high-power vacuum electron devices, particularly beneficial for the development of next-generation IOTs.
- 22 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53 (6) , 1162-1169
Tapered Cavity as Input Cavity in a High-Power Inductive Output Tube
A novel approach of introducing a tapered geometry to the radial re-entrant input cavity has been adopted in high-power inductive output tube (IOT) to enhance the quality factor of the cavity. The geometrical parameters of the cavity have been optimized to achieve the desired resonant frequency employing an analytical approach. Additionally, a coaxial loop coupler has been designed to efficiently inject input power into the cavity with minimal reflection. Performance parameters like S-parameters and return loss of the tapered reentrant cavity have been evaluated and compared with the conventional radial re-entrant cavity without taper. The novel tapered cavity design yields an improved quality factor of ~3186 compared to a value of 2776 with the conventional design. Furthermore, a significant decrease in the ${S} _{11}$ value from −26.3 to −37.74 dB indicates lower signal reflection in the tapered cavity compared to the conventional one. The optimized cavity has been fabricated and it has been observed that measurement results have a strong agreement with simulation results. Hence, this novel modification significantly contributes to advancing IOT designs for high-power RF applications such as particle accelerators, plasma heating, and communication systems.
- 22 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53 (6) , 1162-1169
Tapered Cavity as Input Cavity in a High-Power Inductive Output Tube
A novel approach of introducing a tapered geometry to the radial re-entrant input cavity has been adopted in high-power inductive output tube (IOT) to enhance the quality factor of the cavity. The geometrical parameters of the cavity have been optimized to achieve the desired resonant frequency employing an analytical approach. Additionally, a coaxial loop coupler has been designed to efficiently inject input power into the cavity with minimal reflection. Performance parameters like S-parameters and return loss of the tapered reentrant cavity have been evaluated and compared with the conventional radial re-entrant cavity without taper. The novel tapered cavity design yields an improved quality factor of ~3186 compared to a value of 2776 with the conventional design. Furthermore, a significant decrease in the ${S} _{11}$ value from −26.3 to −37.74 dB indicates lower signal reflection in the tapered cavity compared to the conventional one. The optimized cavity has been fabricated and it has been observed that measurement results have a strong agreement with simulation results. Hence, this novel modification significantly contributes to advancing IOT designs for high-power RF applications such as particle accelerators, plasma heating, and communication systems.
- Open Access
- 1 January 2025
- Published by Wiley in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 2025 (1)
Performance Evaluation of Wideband Dual Port Octagonal‐Shaped Millimeter‐Wave MIMO Antenna for Satellite Communication
A printed MIMO antenna specifically designed for small satellite communication has been presented in this paper. The antenna is invented of two radiators resonating at millimeter‐wave and constructed using Rogers’s RT duroid 5880. The design includes two identical octagonal patches with a diamond‐shaped slot and having two quadrilateral notches. These elements are placed over a substrate and connected to a microstrip transmission line that embeds a quarter‐wave transformer. To establish the effectiveness of the MIMO antenna being proposed, a comparative analysis is conducted between its simulated and experimental performance. Each radiator in the antenna setup includes partial ground, which forms the back layer of the substrate. The design is simulated on the CST tool, and measurements are conducted on a Rohde and Schwarz vector network analyzer. The obtained results show a favorable level of agreement with the simulated outcomes, validating the effectiveness of the proposed MIMO antenna. The antenna design offers exceptional features such as wide bandwidth, self‐isolated, high gain, and a directional radiation pattern while also supporting a wide frequency band, making it an ideal choice for 28 GHz band applications. The performance of MIMO antennas in diversity can be determined using parameters such as envelope correlation coefficient (ECC), diversity gain (DG), and total active reflection coefficient (TARC). Satellite communication will be improved by implementing the suggested MIMO antenna through upgrading small satellite communication systems.
- 1 January 2025
- Published by Wiley in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 2025 (1)
Open AccessPerformance Evaluation of Wideband Dual Port Octagonal‐Shaped Millimeter‐Wave MIMO Antenna for Satellite Communication
A printed MIMO antenna specifically designed for small satellite communication has been presented in this paper. The antenna is invented of two radiators resonating at millimeter‐wave and constructed using Rogers’s RT duroid 5880. The design includes two identical octagonal patches with a diamond‐shaped slot and having two quadrilateral notches. These elements are placed over a substrate and connected to a microstrip transmission line that embeds a quarter‐wave transformer. To establish the effectiveness of the MIMO antenna being proposed, a comparative analysis is conducted between its simulated and experimental performance. Each radiator in the antenna setup includes partial ground, which forms the back layer of the substrate. The design is simulated on the CST tool, and measurements are conducted on a Rohde and Schwarz vector network analyzer. The obtained results show a favorable level of agreement with the simulated outcomes, validating the effectiveness of the proposed MIMO antenna. The antenna design offers exceptional features such as wide bandwidth, self‐isolated, high gain, and a directional radiation pattern while also supporting a wide frequency band, making it an ideal choice for 28 GHz band applications. The performance of MIMO antennas in diversity can be determined using parameters such as envelope correlation coefficient (ECC), diversity gain (DG), and total active reflection coefficient (TARC). Satellite communication will be improved by implementing the suggested MIMO antenna through upgrading small satellite communication systems.
- Open Access
- 30 September 2023
- Published by Wiley in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 2023, 1-14
A High-Frequency Planar-Configured Millimeter-Wave MIMO Antenna for Fifth-Generation NR Operations
This article presents a simple planar millimeter-wave (mm-wave) multiple input multiple output (MIMO) antenna with four closely spaced radiating elements. The antenna is intended to enhance the bandwidth for 5G new radio (NR) applications and also cover the industrial Ka-band (26.5-40 GHz), Q-band (30-50 GHz), and U-band (40-60 GHz) frequency ranges. The antenna is designed using Rogers RT/duroid 5880 substrate with a size of mm3. The proposed antenna consists of four identical radiating elements with two of them positioned in a linear configuration facing each other, while the other two elements are placed opposite to the first two, which improves isolation between the elements. Across the entire operating frequency range (26-60 GHz), the antenna demonstrated excellent performance, including 34 GHz wide bandwidth, high isolation of >25 dB, nearly omnidirectional radiation patterns, high gain of 11.1 dB with a high radiation efficiency of 94%, low envelope correlation coefficient (ECC) of 0.0068, and high diversity gain (DG) of 9.967 dB. The simulated findings exhibit a strong positive correlation with the experimental results. The proposed MIMO antenna design is a promising solution for 5G NR applications.
- 30 September 2023
- Published by Wiley in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 2023, 1-14
Open AccessA High-Frequency Planar-Configured Millimeter-Wave MIMO Antenna for Fifth-Generation NR Operations
This article presents a simple planar millimeter-wave (mm-wave) multiple input multiple output (MIMO) antenna with four closely spaced radiating elements. The antenna is intended to enhance the bandwidth for 5G new radio (NR) applications and also cover the industrial Ka-band (26.5-40 GHz), Q-band (30-50 GHz), and U-band (40-60 GHz) frequency ranges. The antenna is designed using Rogers RT/duroid 5880 substrate with a size of mm3. The proposed antenna consists of four identical radiating elements with two of them positioned in a linear configuration facing each other, while the other two elements are placed opposite to the first two, which improves isolation between the elements. Across the entire operating frequency range (26-60 GHz), the antenna demonstrated excellent performance, including 34 GHz wide bandwidth, high isolation of >25 dB, nearly omnidirectional radiation patterns, high gain of 11.1 dB with a high radiation efficiency of 94%, low envelope correlation coefficient (ECC) of 0.0068, and high diversity gain (DG) of 9.967 dB. The simulated findings exhibit a strong positive correlation with the experimental results. The proposed MIMO antenna design is a promising solution for 5G NR applications.
- Open Access
- 31 August 2023
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2023, 1-19
Advancing 5G Connectivity: A Comprehensive Review of MIMO Antennas for 5G Applications
The review focuses on the emergence of 5G wireless communication and the need for multiple-input multiple-output antennas to support high-speed communication systems. The article discusses the advantages of MIMO antennas, including increased channel capacity and the ability to focus radio frequency energy on specific users. However, the challenges of creating compact MIMO antennas with ideal isolation are addressed, including short wavelengths, connection losses, constrained bandwidth, and path losses in the millimeter-wave range. Design techniques and methods to enhance the performance of conventional antennas for 5G applications are discussed, along with potential solutions for upcoming challenges. The article provides an overview of MIMO antennas for 5G applications, covering frequency bands, system architecture, advantages, challenges, advancements, performance enhancement techniques, design techniques, and state-of-the-art developments.
- 31 August 2023
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2023, 1-19
Open AccessAdvancing 5G Connectivity: A Comprehensive Review of MIMO Antennas for 5G Applications
The review focuses on the emergence of 5G wireless communication and the need for multiple-input multiple-output antennas to support high-speed communication systems. The article discusses the advantages of MIMO antennas, including increased channel capacity and the ability to focus radio frequency energy on specific users. However, the challenges of creating compact MIMO antennas with ideal isolation are addressed, including short wavelengths, connection losses, constrained bandwidth, and path losses in the millimeter-wave range. Design techniques and methods to enhance the performance of conventional antennas for 5G applications are discussed, along with potential solutions for upcoming challenges. The article provides an overview of MIMO antennas for 5G applications, covering frequency bands, system architecture, advantages, challenges, advancements, performance enhancement techniques, design techniques, and state-of-the-art developments.
- 22 August 2016
- Published by Taylor & Francis in Journal of Electromagnetic Waves and Applications
- Vol. 30 (14) , 1918-1928
Theoretical design of the gun-cum-input cavity and focusing structure envisaged for a 350 MHz, 100 kW (CW) inductive output tube
The paper reports the theoretical approach and computer-aided design results for a 350 MHz, 100 kW (CW) inductive output tube. The design considerations and methodologies employed for electromagnetic simulation of individual electron gun and RF cavity assemblies and that of their combined assembly were presented. The electron gun parameters namely the beam radius, perveance and electrodes dimensions were optimized. The input cavity was designed and the parameters, namely the resonant frequency, radius and length of the cavity with respect to the desired propagating mode were characterized. The combined integrated model demonstrates the RF input cavity placed onto the gun structure. The interaction of electron beam (40 kV, 3.5 A) and applied input RF signal of 400 W produces an RF current of ~ 85 A in the interaction gap (i.e. cathode-grid spacing). The focusing structure of the device necessary for getting the efficient amplification has also been designed and optimized. The simulations presented in the paper are carried out using CST, MAGIC2D and TRAK codes.
- 22 August 2016
- Published by Taylor & Francis in Journal of Electromagnetic Waves and Applications
- Vol. 30 (14) , 1918-1928
Theoretical design of the gun-cum-input cavity and focusing structure envisaged for a 350 MHz, 100 kW (CW) inductive output tube
The paper reports the theoretical approach and computer-aided design results for a 350 MHz, 100 kW (CW) inductive output tube. The design considerations and methodologies employed for electromagnetic simulation of individual electron gun and RF cavity assemblies and that of their combined assembly were presented. The electron gun parameters namely the beam radius, perveance and electrodes dimensions were optimized. The input cavity was designed and the parameters, namely the resonant frequency, radius and length of the cavity with respect to the desired propagating mode were characterized. The combined integrated model demonstrates the RF input cavity placed onto the gun structure. The interaction of electron beam (40 kV, 3.5 A) and applied input RF signal of 400 W produces an RF current of ~ 85 A in the interaction gap (i.e. cathode-grid spacing). The focusing structure of the device necessary for getting the efficient amplification has also been designed and optimized. The simulations presented in the paper are carried out using CST, MAGIC2D and TRAK codes.