Michael Geske
Research Subjects
Research Interests
Michael Geske has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
Frank Rosowski
3 shared publications- Frank Rosowski
BasCat—UniCat BASF JointLab, Technische Universität Berlin, Hardenberstraße 36, 10623 Berlin, Germany
3 shared publications - Mohammad Khatamirad
BasCat – UniCat BASF JointLab
3 shared publications - Aleks Arinchtein
Technische Universität Berlin, Straße des 17. Juni 124 10623 Berlin Germany
2 shared publications - Chiara Boscagli
Hte GmbH
2 shared publications Grigorios Kolios
2 shared publications
Latest Publications
- Open Access
- 6 November 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Advancing Rhodium-based Catalysts in Ethanol Synthesis through Tandem Catalysis
The direct conversion of syngas (CO + H2) to ethanol from renewable resources emerges as a promising alternative to conventional starch- and sugar-based production routes. Despite various catalytic systems being considered, promoted rhodium-based catalysts consistently offer the highest yields towards C2+ oxygenates and ethanol, in particular. While manganese remains the promoter of choice, the complex product spectrum significantly impedes industrial application due to its energy- and cost-intensive separation. Herein, we report tandem catalytic systems that upgrade rhodium-based catalysts by selectively converting C2+ oxygenates to ethanol. Among different upgrading catalysts and mixing arrangements evaluated, stacking RhMn/SiO2 and CuZn/SiO2 catalysts demonstrated a 2.6-fold increase in ethanol selectivity (38%) and a 5.8-fold increase in space-time yield (296.6 mg h−1 gcat−1). This system maintained stable operation for over 300 h on stream, positioning it as one of the most productive systems in direct ethanol synthesis. Co-feed experiments and contact time variations suggested alternating stacking arrangements to enhance ethanol yields further. Our results establish new frontiers in the direct formation of ethanol and suggest tandem catalysts as a promising strategy to advance productivity rates in hydrogenation reactions.
- 6 November 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessAdvancing Rhodium-based Catalysts in Ethanol Synthesis through Tandem Catalysis
The direct conversion of syngas (CO + H2) to ethanol from renewable resources emerges as a promising alternative to conventional starch- and sugar-based production routes. Despite various catalytic systems being considered, promoted rhodium-based catalysts consistently offer the highest yields towards C2+ oxygenates and ethanol, in particular. While manganese remains the promoter of choice, the complex product spectrum significantly impedes industrial application due to its energy- and cost-intensive separation. Herein, we report tandem catalytic systems that upgrade rhodium-based catalysts by selectively converting C2+ oxygenates to ethanol. Among different upgrading catalysts and mixing arrangements evaluated, stacking RhMn/SiO2 and CuZn/SiO2 catalysts demonstrated a 2.6-fold increase in ethanol selectivity (38%) and a 5.8-fold increase in space-time yield (296.6 mg h−1 gcat−1). This system maintained stable operation for over 300 h on stream, positioning it as one of the most productive systems in direct ethanol synthesis. Co-feed experiments and contact time variations suggested alternating stacking arrangements to enhance ethanol yields further. Our results establish new frontiers in the direct formation of ethanol and suggest tandem catalysts as a promising strategy to advance productivity rates in hydrogenation reactions.
- 22 April 2025
- Published by Elsevier in Chemical Engineering Journal
- Vol. 514
Direct resistive heating of a catalytic fixed-bed reactor for ethanol dehydration
- 22 April 2025
- Published by Elsevier in Chemical Engineering Journal
- Vol. 514
Direct resistive heating of a catalytic fixed-bed reactor for ethanol dehydration
- Open Access
- 22 April 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Copper Gallium Aluminum Mixed Metal Oxides as new Alternative Catalyst Candidates for Efficient Conversion of Carbon Dioxide to Methanol and Dimethyl Ether
Converting CO2 with renewable hydrogen requires high-value products to be economically viable due to its inherent energy intensity and associated renewable energy costs. Direct hydrogenation of CO2 via exothermic reactions is appealing given volatile energy prices. Methanol is valuable due to its wide use in the chemical industry and as sustainable fuel component. Indium oxide-based catalysts have been actively researched for several years; however, the scarcity of indium and the need for platinum group metals drive the search for alternatives using more abundant and non-noble metals and metal oxides. Employing a protocol which unites Artificial intelligence boosted atomic scale modelling approaches, advanced synthesis, high-throughput catalytic testing and state of the art characterization, we have developed a Cu-Al-Ga system that produces methanol and dimethyl ether (in different ratios) at highly competitive performance characteristics. The elemental composition of the Cu-Al-Ga catalysts was optimized towards a low gallium content to favor economic feasibility. The final lead composition with around 1 wt.% Ga content showed high activity while the ratio between MeOH and DME can be precisely adjusted by the reaction conditions in terms of temperature and syngas composition. Even in CO2 rich syngas flows, the catalyst remains active and selective towards the primary products. In addition, we introduce an advanced simulation protocol for studying potential surface changes under reactive condition to shed light on potential dynamical active site formations and their impact on reaction mechanisms.
- 22 April 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessCopper Gallium Aluminum Mixed Metal Oxides as new Alternative Catalyst Candidates for Efficient Conversion of Carbon Dioxide to Methanol and Dimethyl Ether
Converting CO2 with renewable hydrogen requires high-value products to be economically viable due to its inherent energy intensity and associated renewable energy costs. Direct hydrogenation of CO2 via exothermic reactions is appealing given volatile energy prices. Methanol is valuable due to its wide use in the chemical industry and as sustainable fuel component. Indium oxide-based catalysts have been actively researched for several years; however, the scarcity of indium and the need for platinum group metals drive the search for alternatives using more abundant and non-noble metals and metal oxides. Employing a protocol which unites Artificial intelligence boosted atomic scale modelling approaches, advanced synthesis, high-throughput catalytic testing and state of the art characterization, we have developed a Cu-Al-Ga system that produces methanol and dimethyl ether (in different ratios) at highly competitive performance characteristics. The elemental composition of the Cu-Al-Ga catalysts was optimized towards a low gallium content to favor economic feasibility. The final lead composition with around 1 wt.% Ga content showed high activity while the ratio between MeOH and DME can be precisely adjusted by the reaction conditions in terms of temperature and syngas composition. Even in CO2 rich syngas flows, the catalyst remains active and selective towards the primary products. In addition, we introduce an advanced simulation protocol for studying potential surface changes under reactive condition to shed light on potential dynamical active site formations and their impact on reaction mechanisms.
- Open Access
- 12 December 2022
- Published by Wiley in ChemCatChem
- Vol. 15 (1)
Silica‐supported Catalyst System Rh−Mn−Ir−Li−Ti in Syngas to Ethanol Reaction: Reactivity Trends and Performance Optimization
Ethanol is a high‐value chemical that can be produced from syngas derived from fossil or renewable resources. Silica‐supported catalysts based on Rh are reported to show the best performance so far. We report a comprehensive investigation for influence of catalyst composition on performance in syngas conversion to ethanol. We evaluate 53 different silica‐supported catalysts with a varying degree of Rh, Mn, Ir, Li and Ti, via high‐throughput testing. Correlation analysis reveals that Li and Ir tend to increase the selectivity to C2+ oxygenates, and catalysts with a 0.95 molar ratio of Rh : Mn show a tendency for high CO conversion. The composition 2.8Rh, 0.45Mn, 1.3Ir, 0.04Li, where the numbers indicate weight percentage, is identified to yield one of the highest C2+ oxygenate values reported in the literature so far. Moreover, combining this catalyst with a hydrogenation catalyst and converting C2+ oxygenates to ethanol, provides one of the highest ethanol yields reported so far in literature.
- 12 December 2022
- Published by Wiley in ChemCatChem
- Vol. 15 (1)
Open AccessSilica‐supported Catalyst System Rh−Mn−Ir−Li−Ti in Syngas to Ethanol Reaction: Reactivity Trends and Performance Optimization
Ethanol is a high‐value chemical that can be produced from syngas derived from fossil or renewable resources. Silica‐supported catalysts based on Rh are reported to show the best performance so far. We report a comprehensive investigation for influence of catalyst composition on performance in syngas conversion to ethanol. We evaluate 53 different silica‐supported catalysts with a varying degree of Rh, Mn, Ir, Li and Ti, via high‐throughput testing. Correlation analysis reveals that Li and Ir tend to increase the selectivity to C2+ oxygenates, and catalysts with a 0.95 molar ratio of Rh : Mn show a tendency for high CO conversion. The composition 2.8Rh, 0.45Mn, 1.3Ir, 0.04Li, where the numbers indicate weight percentage, is identified to yield one of the highest C2+ oxygenate values reported in the literature so far. Moreover, combining this catalyst with a hydrogenation catalyst and converting C2+ oxygenates to ethanol, provides one of the highest ethanol yields reported so far in literature.
- Open Access
A Systematic Approach to Study Complex Ternary Co-Promoter Interactions: Addition of Ir, Li, and Ti to RhMn/SiO2 for Syngas Conversion to Ethanol
The direct conversion of synthesis gas could open up economically viable routes for the efficient production of ethanol. RhMn/SiO2 represents one of the most active systems reported thus far. Potential improvements were reported by added dopants, i.e., Ir, Ti, and Li. Yet, combining these elements leads to contradicting results, owing to the complexity of the interactions in a multi-promoted system. This complexity is often encountered in heterogeneous catalysis. We report a systematic data-driven approach for the assessment of complex multi-promoter interactions based on a combination of design-of-experiment, high-throughput experimentation, statistical analysis, and mechanistic assessment. We illustrate this approach for the system RhMn/SiO2 promoted with Ir, Li, and Ti. Using this approach, we investigate the impact of promoters’ interactions on a mechanistic level. Our analysis depicts the means to learn hidden correlations in the performance data and, additionally, high performance for ethanol yield for the RhMnIr/SiO2 catalyst. The method presented outlines an efficient way to also elucidate co-promoter interactions in other complex environments.
Open AccessA Systematic Approach to Study Complex Ternary Co-Promoter Interactions: Addition of Ir, Li, and Ti to RhMn/SiO2 for Syngas Conversion to Ethanol
The direct conversion of synthesis gas could open up economically viable routes for the efficient production of ethanol. RhMn/SiO2 represents one of the most active systems reported thus far. Potential improvements were reported by added dopants, i.e., Ir, Ti, and Li. Yet, combining these elements leads to contradicting results, owing to the complexity of the interactions in a multi-promoted system. This complexity is often encountered in heterogeneous catalysis. We report a systematic data-driven approach for the assessment of complex multi-promoter interactions based on a combination of design-of-experiment, high-throughput experimentation, statistical analysis, and mechanistic assessment. We illustrate this approach for the system RhMn/SiO2 promoted with Ir, Li, and Ti. Using this approach, we investigate the impact of promoters’ interactions on a mechanistic level. Our analysis depicts the means to learn hidden correlations in the performance data and, additionally, high performance for ethanol yield for the RhMnIr/SiO2 catalyst. The method presented outlines an efficient way to also elucidate co-promoter interactions in other complex environments.
- Open Access
Influence of Phase Composition and Pretreatment on the Conversion of Iron Oxides into Iron Carbides in Syngas Atmospheres
CO2 Fischer–Tropsch synthesis (CO2–FTS) is a promising technology enabling conversion of CO2 into valuable chemical feedstocks via hydrogenation. Iron–based CO2–FTS catalysts are known for their high activities and selectivities towards the formation of higher hydrocarbons. Importantly, iron carbides are the presumed active phase strongly associated with the formation of higher hydrocarbons. Yet, many factors such as reaction temperature, atmosphere, and pressure can lead to complex transformations between different oxide and/or carbide phases, which, in turn, alter selectivity. Thus, understanding the mechanism and kinetics of carbide formation remains challenging. We propose model–type iron oxide films of controlled nanostructure and phase composition as model materials to study carbide formation in syngas atmospheres. In the present work, different iron oxide precursor films with controlled phase composition (hematite, ferrihydrite, maghemite, maghemite/magnetite) and ordered mesoporosity are synthesized using the evaporation–induced self–assembly (EISA) approach. The model materials are then exposed to a controlled atmosphere of CO/H2 at 300 °C. Physicochemical analysis of the treated materials indicates that all oxides convert into carbides with a core–shell structure. The structure appears to consist of crystalline carbide cores surrounded by a partially oxidized carbide shell of low crystallinity. Larger crystallites in the original iron oxide result in larger carbide cores. The presented simple route for the synthesis and analysis of soft–templated iron carbide films will enable the elucidation of the dynamics of the oxide to carbide transformation in future work.
Open AccessInfluence of Phase Composition and Pretreatment on the Conversion of Iron Oxides into Iron Carbides in Syngas Atmospheres
CO2 Fischer–Tropsch synthesis (CO2–FTS) is a promising technology enabling conversion of CO2 into valuable chemical feedstocks via hydrogenation. Iron–based CO2–FTS catalysts are known for their high activities and selectivities towards the formation of higher hydrocarbons. Importantly, iron carbides are the presumed active phase strongly associated with the formation of higher hydrocarbons. Yet, many factors such as reaction temperature, atmosphere, and pressure can lead to complex transformations between different oxide and/or carbide phases, which, in turn, alter selectivity. Thus, understanding the mechanism and kinetics of carbide formation remains challenging. We propose model–type iron oxide films of controlled nanostructure and phase composition as model materials to study carbide formation in syngas atmospheres. In the present work, different iron oxide precursor films with controlled phase composition (hematite, ferrihydrite, maghemite, maghemite/magnetite) and ordered mesoporosity are synthesized using the evaporation–induced self–assembly (EISA) approach. The model materials are then exposed to a controlled atmosphere of CO/H2 at 300 °C. Physicochemical analysis of the treated materials indicates that all oxides convert into carbides with a core–shell structure. The structure appears to consist of crystalline carbide cores surrounded by a partially oxidized carbide shell of low crystallinity. Larger crystallites in the original iron oxide result in larger carbide cores. The presented simple route for the synthesis and analysis of soft–templated iron carbide films will enable the elucidation of the dynamics of the oxide to carbide transformation in future work.
- Open Access
- 24 April 2014
- Published by Wiley in Angewandte Chemie
- Vol. 126 (33) , 8919-8923
Zentren der Methanaktivierung auf Oberflächen von Lithium‐dotiertem MgO
Die mittels Dichtefunktionaltheorie berechneten Energiebarrieren für die H‐Abstraktion durch Sauerstoffradikale in Li‐dotiertem MgO sind viel kleiner (12±6 kJ mol−1) als die Barrieren, die man bei unterschiedlichen Methanaktivierungsexperimenten findet (80–160 kJ mol−1). Das nährt weitere Zweifel an Lunsfords Hypothese, dass Li+O.−‐Paare die aktiven Zentren sind. Temperaturprogrammierte oxidative Kupplungsreaktionen von Methan (OCM) zeigen, dass bei reinem und Li‐dotiertem MgO die gleichen Zentren für die Reaktion verantwortlich sind. MgO‐Katalysatoren, die durch Sol‐Gel‐Synthese hergestellt wurden, zeigen große Unterschiede zwischen anfänglicher Aktivität und der Aktivität im stationären Zustand. Transmissionselektronenmikroskopie zeigt, dass damit substanzielle morphologische Veränderungen und Restrukturierungen der Oberfläche einhergehen. Berechnungen an (MgO)9‐Clustermodellen ergeben, dass CH4 heterolytisch an Mg2+O2−‐Paaren chemisorbiert wird, die sich an Stufen oder Ecken befinden. Die homolytische Freisetzung von Methylradikalen erfordert jedoch die Anwesenheit von O2 auf der Oberfläche.
- 24 April 2014
- Published by Wiley in Angewandte Chemie
- Vol. 126 (33) , 8919-8923
Open AccessZentren der Methanaktivierung auf Oberflächen von Lithium‐dotiertem MgO
Die mittels Dichtefunktionaltheorie berechneten Energiebarrieren für die H‐Abstraktion durch Sauerstoffradikale in Li‐dotiertem MgO sind viel kleiner (12±6 kJ mol−1) als die Barrieren, die man bei unterschiedlichen Methanaktivierungsexperimenten findet (80–160 kJ mol−1). Das nährt weitere Zweifel an Lunsfords Hypothese, dass Li+O.−‐Paare die aktiven Zentren sind. Temperaturprogrammierte oxidative Kupplungsreaktionen von Methan (OCM) zeigen, dass bei reinem und Li‐dotiertem MgO die gleichen Zentren für die Reaktion verantwortlich sind. MgO‐Katalysatoren, die durch Sol‐Gel‐Synthese hergestellt wurden, zeigen große Unterschiede zwischen anfänglicher Aktivität und der Aktivität im stationären Zustand. Transmissionselektronenmikroskopie zeigt, dass damit substanzielle morphologische Veränderungen und Restrukturierungen der Oberfläche einhergehen. Berechnungen an (MgO)9‐Clustermodellen ergeben, dass CH4 heterolytisch an Mg2+O2−‐Paaren chemisorbiert wird, die sich an Stufen oder Ecken befinden. Die homolytische Freisetzung von Methylradikalen erfordert jedoch die Anwesenheit von O2 auf der Oberfläche.