Tina Tasheva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tina Tasheva has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Vesselin Dimitrov
6 shared publicationsTakayuki Komatsu
4 shared publicationsTsuyoshi Honma
2 shared publications- Tsuyoshi Honma
Department of Materials Science and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka-cho, Nagaoka 940-2188, Japan
2 shared publications Adriana Batsova
Department of Silicate Technology University of Chemical Technology and Metallurgy Sofia Bulgaria
1 shared publicationAlbena Yoleva
Department of Silicate Technology University of Chemical Technology and Metallurgy Sofia Bulgaria
1 shared publication
Latest Publications
- Open Access
Electrical and Dielectric Properties of ZnO-BaO-V2O5 Glasses
The relationship between composition, structure, and electrical properties is essential for understanding charge transport in vanadate glasses. In this study, the influence of ZnO concentration and thermal treatment on the structure, electrical conductivity, and dielectric relaxation of xZnO–(35 − x)BaO–65V2O5 glasses (x = 0–20 mol%) was systematically investigated. Two series of glasses, as-quenched and annealed, were prepared by the melt-quenching technique and characterized by temperature-dependent direct current (DC) conductivity, broadband dielectric spectroscopy, and Raman spectroscopy. The DC conductivity exhibited Arrhenius behavior with two thermally activated conduction regions. Annealing reduced the activation energy at higher temperatures, indicating structural relaxation and stabilization of the glass network. Dielectric spectroscopy revealed two distinct relaxation mechanisms over the frequency range of 0.1 Hz–100 kHz, whereas thermal treatment had only a minor influence on the dielectric relaxation behavior. Raman spectra showed that ZnO progressively modifies the vanadate network through the formation of V–O–Zn linkages while preserving the characteristic terminal V=O bonds. Annealing enhanced the short-range structural ordering without altering the fundamental glass structure. Among the investigated compositions, the glass containing 7 mol% ZnO exhibited distinct structural and electrical characteristics, suggesting that this composition corresponds to a transition in the structural organization of the glass network. The combined structural and electrical analyses demonstrate a clear correlation between ZnO-induced structural modifications and the charge transport properties of ZnO–BaO–V2O5 glasses.
Open AccessElectrical and Dielectric Properties of ZnO-BaO-V2O5 Glasses
The relationship between composition, structure, and electrical properties is essential for understanding charge transport in vanadate glasses. In this study, the influence of ZnO concentration and thermal treatment on the structure, electrical conductivity, and dielectric relaxation of xZnO–(35 − x)BaO–65V2O5 glasses (x = 0–20 mol%) was systematically investigated. Two series of glasses, as-quenched and annealed, were prepared by the melt-quenching technique and characterized by temperature-dependent direct current (DC) conductivity, broadband dielectric spectroscopy, and Raman spectroscopy. The DC conductivity exhibited Arrhenius behavior with two thermally activated conduction regions. Annealing reduced the activation energy at higher temperatures, indicating structural relaxation and stabilization of the glass network. Dielectric spectroscopy revealed two distinct relaxation mechanisms over the frequency range of 0.1 Hz–100 kHz, whereas thermal treatment had only a minor influence on the dielectric relaxation behavior. Raman spectra showed that ZnO progressively modifies the vanadate network through the formation of V–O–Zn linkages while preserving the characteristic terminal V=O bonds. Annealing enhanced the short-range structural ordering without altering the fundamental glass structure. Among the investigated compositions, the glass containing 7 mol% ZnO exhibited distinct structural and electrical characteristics, suggesting that this composition corresponds to a transition in the structural organization of the glass network. The combined structural and electrical analyses demonstrate a clear correlation between ZnO-induced structural modifications and the charge transport properties of ZnO–BaO–V2O5 glasses.
- Open Access
Synthesis, Structure and Dielectric Characteristics of Tellurovanadate Glasses Containing Bismuth Oxide
Two series of glasses with compositions (90 − x)TeO2-xV2O5-10Bi2O3 and (80 − x)TeO2-xV2O5-20Bi2O3, where x = 20, 30, 40 mol %, were synthesized. Glasses were obtained by the melt-quenching technique. The molar volume (33.48–48.37 cm3/mol) and oxygen packing density (71.69–77.64 mol/cm3) were calculated based on experimental density measurements. Both parameters increase with the increase in V2O5 and the decrease in TeO2 content. Infrared spectra were recorded in the range of 2000–400 cm−1 and Raman spectra in the 90–1280 cm−1 range. The C1s, O1s, Te3d, V2p and Bi4f photoelectron lines were recorded. The dielectric characteristics of the glasses were measured by impedance spectroscopy at room temperature in the frequency range from 100 Hz to 1 MHz. The glasses in the studied system demonstrate a strong dependence on the composition, with the occasional addition of high contents of TeO2 and V2O5 leading to a significant change in the dielectric properties of the samples.
Open AccessSynthesis, Structure and Dielectric Characteristics of Tellurovanadate Glasses Containing Bismuth Oxide
Two series of glasses with compositions (90 − x)TeO2-xV2O5-10Bi2O3 and (80 − x)TeO2-xV2O5-20Bi2O3, where x = 20, 30, 40 mol %, were synthesized. Glasses were obtained by the melt-quenching technique. The molar volume (33.48–48.37 cm3/mol) and oxygen packing density (71.69–77.64 mol/cm3) were calculated based on experimental density measurements. Both parameters increase with the increase in V2O5 and the decrease in TeO2 content. Infrared spectra were recorded in the range of 2000–400 cm−1 and Raman spectra in the 90–1280 cm−1 range. The C1s, O1s, Te3d, V2p and Bi4f photoelectron lines were recorded. The dielectric characteristics of the glasses were measured by impedance spectroscopy at room temperature in the frequency range from 100 Hz to 1 MHz. The glasses in the studied system demonstrate a strong dependence on the composition, with the occasional addition of high contents of TeO2 and V2O5 leading to a significant change in the dielectric properties of the samples.
- Open Access
- 3 September 2025
- Published by University of Chemical Technology and Metallurgy in Journal of Chemical Technology and Metallurgy
- Vol. 60 (5) , 843-852
THE INFLUENCE OF THE CRUCIBLE AND THE COOLING RATE ON THE STRUCTURE OF GLASSES AND GLASS-CRYSTALLINE MATERIALS IN THE CaO-Na2O-P2O5-B2O3 SYSTEM
Batches with composition 47.2B2O3-24.98Na2O-27.54CaO-0.27P2O5 (mol %) were melted in porcelain and corundum crucibles by melt quenching and normal cooling rate techniques. As a result, four different materials were obtained. Powder X-ray diffraction analysis showed that the sample melt in a corundum crucible and melt-quenched was almost fully amorphous, whereas its slowly cooled analogue exhibited near-complete crystallization. Samples prepared in porcelain crucibles, regardless of cooling technique, had predominantly amorphous structures, but two different crystalline phases appeared when the melts were slowly cooled. Scanning electron microscopy revealed distinct microstructural differences between the slowly cooled samples from porcelain and corundum crucibles. Fourier-transform infrared and Raman spectroscopy identified BO3 and BO4 units as the main structural units, likelyinterconnected in pentaborate superstructural units. The influence of crucible material on crystallization behavior and phase formation was discussed.
- 3 September 2025
- Published by University of Chemical Technology and Metallurgy in Journal of Chemical Technology and Metallurgy
- Vol. 60 (5) , 843-852
Open AccessTHE INFLUENCE OF THE CRUCIBLE AND THE COOLING RATE ON THE STRUCTURE OF GLASSES AND GLASS-CRYSTALLINE MATERIALS IN THE CaO-Na2O-P2O5-B2O3 SYSTEM
Batches with composition 47.2B2O3-24.98Na2O-27.54CaO-0.27P2O5 (mol %) were melted in porcelain and corundum crucibles by melt quenching and normal cooling rate techniques. As a result, four different materials were obtained. Powder X-ray diffraction analysis showed that the sample melt in a corundum crucible and melt-quenched was almost fully amorphous, whereas its slowly cooled analogue exhibited near-complete crystallization. Samples prepared in porcelain crucibles, regardless of cooling technique, had predominantly amorphous structures, but two different crystalline phases appeared when the melts were slowly cooled. Scanning electron microscopy revealed distinct microstructural differences between the slowly cooled samples from porcelain and corundum crucibles. Fourier-transform infrared and Raman spectroscopy identified BO3 and BO4 units as the main structural units, likelyinterconnected in pentaborate superstructural units. The influence of crucible material on crystallization behavior and phase formation was discussed.
- Open Access
Study of New Glass–Ceramic and Dense Ceramic Containing Biogenic Hydroxyapatite
A novel bioactive glass–ceramic was developed using biogenic hydroxyapatite (BHA) synthesized from Rapana venosa (Black Sea) shells and monocalcium phosphate monohydrate [Ca(H2PO4)2·H2O] via solid-state synthesis. The prepared batches were obtained by combining BHA with SiO2, B2O3, and Na2O, melted at 1200 °C and melt-quenched in water to form glass–ceramic materials. Dense biogenic hydroxyapatite-based ceramics were successfully sintered at 1200 °C (2 h hold) using a 25 mass % sintering additive composed of 35 mass % B2O3, 45 mass % SiO2, 10 mass % Al2O3, and 10 mass % Na2O. Structural characterization was carried out using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). The resulting materials consisted of a well-defined crystalline hydroxyapatite phase [Ca10(PO4)6(OH)2] alongside an amorphous phase. In samples with increased SiO2 and reduced B2O3 content (composition 3), a finely dispersed Na3Ca6(PO4)5 crystalline phase appeared, with a reduced presence of hydroxyapatite. Bioactivity was assessed in simulated body fluid (SBF) after 10 and 20 days of immersion, confirming the material’s ability to support apatite layer formation. The main structural units SiO4, PO4, and BO3 are interconnected through Si–O–Si, B–O–B, P–O–P, and mixed Si–O–Al linkages, contributing to both structural stability and bioactivity.
Open AccessStudy of New Glass–Ceramic and Dense Ceramic Containing Biogenic Hydroxyapatite
A novel bioactive glass–ceramic was developed using biogenic hydroxyapatite (BHA) synthesized from Rapana venosa (Black Sea) shells and monocalcium phosphate monohydrate [Ca(H2PO4)2·H2O] via solid-state synthesis. The prepared batches were obtained by combining BHA with SiO2, B2O3, and Na2O, melted at 1200 °C and melt-quenched in water to form glass–ceramic materials. Dense biogenic hydroxyapatite-based ceramics were successfully sintered at 1200 °C (2 h hold) using a 25 mass % sintering additive composed of 35 mass % B2O3, 45 mass % SiO2, 10 mass % Al2O3, and 10 mass % Na2O. Structural characterization was carried out using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). The resulting materials consisted of a well-defined crystalline hydroxyapatite phase [Ca10(PO4)6(OH)2] alongside an amorphous phase. In samples with increased SiO2 and reduced B2O3 content (composition 3), a finely dispersed Na3Ca6(PO4)5 crystalline phase appeared, with a reduced presence of hydroxyapatite. Bioactivity was assessed in simulated body fluid (SBF) after 10 and 20 days of immersion, confirming the material’s ability to support apatite layer formation. The main structural units SiO4, PO4, and BO3 are interconnected through Si–O–Si, B–O–B, P–O–P, and mixed Si–O–Al linkages, contributing to both structural stability and bioactivity.
- Open Access
- 6 November 2024
- Published by University of Chemical Technology and Metallurgy in Journal of Chemical Technology and Metallurgy
- Vol. 59 (6) , 1391-1398
FT-IR AND RAMAN SPECTROSCOPY OF ZnO AND MgO CONTAINING GLASSES IN THE B2O3/Na2O/CaO/P2O5 SYSTEM
Glasses with compositions 46.1B2O3-24.4Na2O-26.9CaO.2.6P2O5, xZnO/MgO-22.0B2O3 -(24.4-x)Na2O-27CaO-2.5P2O5 (x = 2.5, 3 mol%) and 1.5ZnO-1.5MgO-22.0B2O3-21.5.Na2O-27CaO-2.5P2O5 were melted by melt quenching technique. The densities of the glasses were measured by the Archimedes principle, using an analytical scale. Glasses possess densities in the 2.538 to 2.623 g cm-1 range. The short-range order was also discussed from the molar volume Vm, cm3 mol-1, and oxygen packing density point of view. The molar volume of the glasses varies between 26.566 - 27.420 cm3 mol-1 and the oxygen packing density is between 73.669 to 76.262 mol cm-3. The Furie transform infrared spectroscopy and Raman spectroscopy were performed to study the main structural units constituting the structure of the samples. The main structural units were found to be BO3 and BO4 probably connected in pentaborate and triborate structural units. The influence of the ZnO and MgO on the structure and chemical bonding of the glasses was discussed.
- 6 November 2024
- Published by University of Chemical Technology and Metallurgy in Journal of Chemical Technology and Metallurgy
- Vol. 59 (6) , 1391-1398
Open AccessFT-IR AND RAMAN SPECTROSCOPY OF ZnO AND MgO CONTAINING GLASSES IN THE B2O3/Na2O/CaO/P2O5 SYSTEM
Glasses with compositions 46.1B2O3-24.4Na2O-26.9CaO.2.6P2O5, xZnO/MgO-22.0B2O3 -(24.4-x)Na2O-27CaO-2.5P2O5 (x = 2.5, 3 mol%) and 1.5ZnO-1.5MgO-22.0B2O3-21.5.Na2O-27CaO-2.5P2O5 were melted by melt quenching technique. The densities of the glasses were measured by the Archimedes principle, using an analytical scale. Glasses possess densities in the 2.538 to 2.623 g cm-1 range. The short-range order was also discussed from the molar volume Vm, cm3 mol-1, and oxygen packing density point of view. The molar volume of the glasses varies between 26.566 - 27.420 cm3 mol-1 and the oxygen packing density is between 73.669 to 76.262 mol cm-3. The Furie transform infrared spectroscopy and Raman spectroscopy were performed to study the main structural units constituting the structure of the samples. The main structural units were found to be BO3 and BO4 probably connected in pentaborate and triborate structural units. The influence of the ZnO and MgO on the structure and chemical bonding of the glasses was discussed.
- 25 July 2024
- Published by Wiley in International Journal of Applied Glass Science
- Vol. 16 (1)
Development of multicomponent glasses for application as a glazing layer on dental zirconia
This study presents the development of multicomponent glasses for glaze layers for dental yttria‐stabilized tetragonal zirconia (Y‐TZP). The samples were melted in the temperature range of 1 250–1 400°C and were cast in water to obtain a frit. The frits were grounded to a powder with a particle size of less than 40 µm. To study the crystallization tendency of melted glasses, they were thermally treated at 800°C and X‐ray diffraction analyses were performed for both types of samples. The structure of the glasses was investigated by the Fourier‐transform infrared spectroscopy. The thermal expansion coefficient, CTE, the glass‐transition temperature, T g , and the softening temperature, T s , were defined. To test the glaze layer on zirconia ceramic, glass powders with different compositions were mixed with modeling fluid and applied on zirconia specimens and then fired at 800°C in a vacuum dental furnace. Scanning electron microscopy, SEM, was used to observe a cross‐section of the glass–ceramic contact on a glazed zirconia ceramic specimen. Glass with the highest content of alkaline oxides is characterized by the closest CTE to zirconium ceramics (10.10 −6 K −1 ), the greatest transparency and good fluidity, and shows good adhesion to the zirconia. The glaze layer is homogeneous without cracks, pores, and crystals.
- 25 July 2024
- Published by Wiley in International Journal of Applied Glass Science
- Vol. 16 (1)
Development of multicomponent glasses for application as a glazing layer on dental zirconia
This study presents the development of multicomponent glasses for glaze layers for dental yttria‐stabilized tetragonal zirconia (Y‐TZP). The samples were melted in the temperature range of 1 250–1 400°C and were cast in water to obtain a frit. The frits were grounded to a powder with a particle size of less than 40 µm. To study the crystallization tendency of melted glasses, they were thermally treated at 800°C and X‐ray diffraction analyses were performed for both types of samples. The structure of the glasses was investigated by the Fourier‐transform infrared spectroscopy. The thermal expansion coefficient, CTE, the glass‐transition temperature, T g , and the softening temperature, T s , were defined. To test the glaze layer on zirconia ceramic, glass powders with different compositions were mixed with modeling fluid and applied on zirconia specimens and then fired at 800°C in a vacuum dental furnace. Scanning electron microscopy, SEM, was used to observe a cross‐section of the glass–ceramic contact on a glazed zirconia ceramic specimen. Glass with the highest content of alkaline oxides is characterized by the closest CTE to zirconium ceramics (10.10 −6 K −1 ), the greatest transparency and good fluidity, and shows good adhesion to the zirconia. The glaze layer is homogeneous without cracks, pores, and crystals.
- 13 January 2022
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 581
Structural role of Nb2O5 in glass-forming ability, electronic polarizability and nanocrystallization in glasses: A review
- 13 January 2022
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 581
Structural role of Nb2O5 in glass-forming ability, electronic polarizability and nanocrystallization in glasses: A review
- 1 October 2021
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 570
Correlation between structure and optical basicity of glasses in the TeO2-V2O5-MoO3 system
- 1 October 2021
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 570
Correlation between structure and optical basicity of glasses in the TeO2-V2O5-MoO3 system
- 26 March 2021
- Published by Wiley in International Journal of Applied Glass Science
- Vol. 12 (3) , 424-442
Electronic polarizability in silicate glasses by comparison of experimental and theoretical optical basicities
The concept of optical basicity proposed by Duffy has been recognized as an extremely important issue in science and technology of glasses. In this article, the refractive index ( n o )‐based optical basicity Λ( n o ) of some binary and ternary silicate glasses was evaluated using the Lorentz–Lorenz formula, and the discrepancy between the values of Λ( n o ) and the theoretically calculated optical basicity Λ th was analyzed to understand more deeply the electronic polarizability in binary and ternary silicate glasses. A suitable value of the optical basicity for each oxide predicting a good quantitative composition dependence of optical basicity in a given glass system was proposed. The suitable value of SiO 2 for the prediction of the optical basicity of silicate glasses is Λ(SiO 2 glass) = 0.53, which is larger than the value of Λ(SiO 2 oxide) = 0.48 being used in the calculation of Λ th so far. Other suitable values such as Λ(Al 2 O 3 glass) = 0.62 and Λ(TiO 2 glass) = 1.04 were proposed. The relationship between the optical basicity and coordination structure in some oxides in silicate glasses was discussed.
- 26 March 2021
- Published by Wiley in International Journal of Applied Glass Science
- Vol. 12 (3) , 424-442
Electronic polarizability in silicate glasses by comparison of experimental and theoretical optical basicities
The concept of optical basicity proposed by Duffy has been recognized as an extremely important issue in science and technology of glasses. In this article, the refractive index ( n o )‐based optical basicity Λ( n o ) of some binary and ternary silicate glasses was evaluated using the Lorentz–Lorenz formula, and the discrepancy between the values of Λ( n o ) and the theoretically calculated optical basicity Λ th was analyzed to understand more deeply the electronic polarizability in binary and ternary silicate glasses. A suitable value of the optical basicity for each oxide predicting a good quantitative composition dependence of optical basicity in a given glass system was proposed. The suitable value of SiO 2 for the prediction of the optical basicity of silicate glasses is Λ(SiO 2 glass) = 0.53, which is larger than the value of Λ(SiO 2 oxide) = 0.48 being used in the calculation of Λ th so far. Other suitable values such as Λ(Al 2 O 3 glass) = 0.62 and Λ(TiO 2 glass) = 1.04 were proposed. The relationship between the optical basicity and coordination structure in some oxides in silicate glasses was discussed.
- Open Access
- 1 February 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1762 (1) , 012027
Structure and dielectric behaviour of glasses in the TeO2-BaO-V2O5 system
The rapid development of telecommunication and information technology aims to design and investigate new functional materials. Glasses in the TeO2-BaO-V2O5 seems to be promising materials within this purpose. In this connection the structure and dielectric properties of the glasses have been studied. Small polaron hopping of V4+ to V5+ ion in the vanadate chains and the influence of BaO and TeO2 on the dielectric permittivity, dielectric losses and frequency depended conductivity of the glasses measured at room temperature in the frequency range from 100 Hz to 1 MHz have been discussed.
- 1 February 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1762 (1) , 012027
Open AccessStructure and dielectric behaviour of glasses in the TeO2-BaO-V2O5 system
The rapid development of telecommunication and information technology aims to design and investigate new functional materials. Glasses in the TeO2-BaO-V2O5 seems to be promising materials within this purpose. In this connection the structure and dielectric properties of the glasses have been studied. Small polaron hopping of V4+ to V5+ ion in the vanadate chains and the influence of BaO and TeO2 on the dielectric permittivity, dielectric losses and frequency depended conductivity of the glasses measured at room temperature in the frequency range from 100 Hz to 1 MHz have been discussed.