Yuanda Su
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yuanda Su has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Baohai Tan
State Key Laboratory of Deep Oil and Gas, China University of Petroleum (East China), Qingdao 266580, China
5 shared publications - Kai Zhang
State Key Laboratory of Deep Oil and Gas, China University of Petroleum (East China), Qingdao 266580, China
5 shared publications - Sheng-Qing Li
School of Geosciences, China University of Petroleum (East China) , Qingdao, Shandong 266580
2 shared publications - Shoutao Xin
ChangQing Branch of CNPC Logging, Xi’an 710200, China
2 shared publications - Bo Zhang
Shuoren Times Technology, Suite 304, Rainbow Plaza, 11 Information Rd, Haidian District, Beijing 100085, China
1 shared publication - Gaofu Wu
East China Measurement and Control Branch of Sinopec Matrix Corporation, Yangzhou 225000, China
1 shared publication
Latest Publications
- Open Access
Temperature-Dependent Electromechanical and Acoustic Responses of a Tubular PZT-5A Transducer: Finite-Element Modeling and Experimental Investigation
Temperature-induced variations in piezoelectric material properties can detune acoustic-logging transducers and alter their electrical, mechanical, and acoustic responses. This study establishes a temperature-dependent finite-element model of a tubular lead zirconate titanate (PZT-5A) transducer over 0–200 °C. Temperature-dependent dielectric, piezoelectric, and elastic parameters were implemented as constitutive functions. Frequency-domain impedance simulations were compared with impedance measurements over 20–200 °C, while transient fluid-loaded simulations and laser-vibrometry measurements were used to characterize the acoustic-pressure and vessel-wall vibration responses. The simulated resonant frequency decreased from 21.379 to 19.35 kHz, and the measured value decreased from 21.135 to 19.55 kHz. The simulated static capacitance increased from 18.8 to 81.0 nF, whereas the measured value increased from 23.7 to 93.0 nF. An isolated geometric-expansion sensitivity analysis indicated that omitted dimensional changes may partly account for this discrepancy. The fitted motional resistance decreased in both the simulations and experiments. The vessel-wall vibration-velocity squared integral decreased from 0.03483 to /s, and the simulated acoustic-pressure squared integral decreased from 2.14926 to 1.59839 Pa2·s. The frequency corresponding to the maximum sound-pressure spectrum also decreased from 22.644 to 21.607 kHz. The agreement in the principal temperature-dependent trends indicates that the model captures the dominant electromechanical behavior, while the remaining capacitance discrepancy highlights the influence of thermal deformation and other nonideal experimental factors. The proposed framework provides a basis for performance prediction and temperature compensation of piezoelectric transducers used in acoustic logging and other elevated-temperature acoustic systems.Open AccessTemperature-Dependent Electromechanical and Acoustic Responses of a Tubular PZT-5A Transducer: Finite-Element Modeling and Experimental Investigation
Temperature-induced variations in piezoelectric material properties can detune acoustic-logging transducers and alter their electrical, mechanical, and acoustic responses. This study establishes a temperature-dependent finite-element model of a tubular lead zirconate titanate (PZT-5A) transducer over 0–200 °C. Temperature-dependent dielectric, piezoelectric, and elastic parameters were implemented as constitutive functions. Frequency-domain impedance simulations were compared with impedance measurements over 20–200 °C, while transient fluid-loaded simulations and laser-vibrometry measurements were used to characterize the acoustic-pressure and vessel-wall vibration responses. The simulated resonant frequency decreased from 21.379 to 19.35 kHz, and the measured value decreased from 21.135 to 19.55 kHz. The simulated static capacitance increased from 18.8 to 81.0 nF, whereas the measured value increased from 23.7 to 93.0 nF. An isolated geometric-expansion sensitivity analysis indicated that omitted dimensional changes may partly account for this discrepancy. The fitted motional resistance decreased in both the simulations and experiments. The vessel-wall vibration-velocity squared integral decreased from 0.03483 to /s, and the simulated acoustic-pressure squared integral decreased from 2.14926 to 1.59839 Pa2·s. The frequency corresponding to the maximum sound-pressure spectrum also decreased from 22.644 to 21.607 kHz. The agreement in the principal temperature-dependent trends indicates that the model captures the dominant electromechanical behavior, while the remaining capacitance discrepancy highlights the influence of thermal deformation and other nonideal experimental factors. The proposed framework provides a basis for performance prediction and temperature compensation of piezoelectric transducers used in acoustic logging and other elevated-temperature acoustic systems. - Open Access
Temperature-Adaptive Excitation Technology for Acoustic Logging Monopole Transducers
Acoustic logging tools, deployed thousands of meters underground to detect geological structures and evaluate reservoir fluids, are essential for oil and gas exploration and development. These tools generate acoustic signals through piezoelectric ceramic transducers. The material properties of piezoelectric ceramics are significantly affected by the high-temperature downhole environment, leading to a failure in impedance matching between the transducer and its excitation circuit. This results in a substantial degradation of the tool’s performance. This paper experimentally obtains the electrical parameters and excitation energy of commonly used monopole transducers at different temperatures. Based on this data, the optimal matching inductance values at various temperatures are calculated. A temperature-adaptive transducer excitation circuit is then designed and implemented. This circuit can adjust the excitation frequency according to the measured temperature to compensate for resonant frequency drift and select the optimal inductor tap via a programmable multiplexer. Experimental results demonstrate that this circuit significantly enhances the transducer’s excitation energy at high temperatures. This technology is expected to markedly improve the operational stability of acoustic logging tools and facilitate the exploration and development of deep and ultra-deep oil and gas resources.
Open AccessTemperature-Adaptive Excitation Technology for Acoustic Logging Monopole Transducers
Acoustic logging tools, deployed thousands of meters underground to detect geological structures and evaluate reservoir fluids, are essential for oil and gas exploration and development. These tools generate acoustic signals through piezoelectric ceramic transducers. The material properties of piezoelectric ceramics are significantly affected by the high-temperature downhole environment, leading to a failure in impedance matching between the transducer and its excitation circuit. This results in a substantial degradation of the tool’s performance. This paper experimentally obtains the electrical parameters and excitation energy of commonly used monopole transducers at different temperatures. Based on this data, the optimal matching inductance values at various temperatures are calculated. A temperature-adaptive transducer excitation circuit is then designed and implemented. This circuit can adjust the excitation frequency according to the measured temperature to compensate for resonant frequency drift and select the optimal inductor tap via a programmable multiplexer. Experimental results demonstrate that this circuit significantly enhances the transducer’s excitation energy at high temperatures. This technology is expected to markedly improve the operational stability of acoustic logging tools and facilitate the exploration and development of deep and ultra-deep oil and gas resources.
- Open Access
Three-Dimensional Acoustic Device for Testing the All-Directional Anisotropic Characteristics of Rock Samples
Many oil and gas fields, especially non-conventional shale and compacted sand reservoirs, have formation anisotropy. The acoustic anisotropy measurement of cores in these reservoirs can guide drilling, well logging, and exploitation. However, almost all core holders are designed for cylinder cores, which are not suitable for all-directional measurements. A three-dimensional measurement device was designed on the basis of the cross-hole sonic logging method. This device mainly consisted of two pairs of transducers, a signal generator, an oscillograph, an omnidirectional positioning system, and a computer control system. By adjusting the measurement latitude and longitude circle automatically, this device scanned spherical sample rocks and obtained full-wave waveforms in all directions. Experiments were performed taking granite from the Jiaodong Peninsula, China, as an example, and the arrival times and velocities of the longitudinal and shear waves were calculated based on the full-wave waveforms. Thereafter, anisotropic physical characterizations were carried out on the basis of these velocities. These data play an important role in guiding formation fracturing and analyzing the stability of borehole walls.
Open AccessThree-Dimensional Acoustic Device for Testing the All-Directional Anisotropic Characteristics of Rock Samples
Many oil and gas fields, especially non-conventional shale and compacted sand reservoirs, have formation anisotropy. The acoustic anisotropy measurement of cores in these reservoirs can guide drilling, well logging, and exploitation. However, almost all core holders are designed for cylinder cores, which are not suitable for all-directional measurements. A three-dimensional measurement device was designed on the basis of the cross-hole sonic logging method. This device mainly consisted of two pairs of transducers, a signal generator, an oscillograph, an omnidirectional positioning system, and a computer control system. By adjusting the measurement latitude and longitude circle automatically, this device scanned spherical sample rocks and obtained full-wave waveforms in all directions. Experiments were performed taking granite from the Jiaodong Peninsula, China, as an example, and the arrival times and velocities of the longitudinal and shear waves were calculated based on the full-wave waveforms. Thereafter, anisotropic physical characterizations were carried out on the basis of these velocities. These data play an important role in guiding formation fracturing and analyzing the stability of borehole walls.
- Open Access
Design of an Acoustic Through-Casing Logging Tool
Well logging is performed in oil and gas exploration wells to obtain the physical characteristics of underground formations. Thereafter, these wells are cased. Through-casing logging is important in mature fields and for wells that are cased without logging due to borehole stability issues. Acoustic through-casing logging is a challenging issue due to the strong interference of casing waves in formation waves, especially when the casing and formation are poorly bonded. An acoustic tool with dual-source transmitters is developed, in which an additional transducer is added to suppress casing waves. First, the operation principle and the overall design of the tool are carried out, including the span distance between the two transmitting transducers and the spacing distance between the transmitting transducer and the receiving transducers. Thereafter, a dual-source transmitting circuit is designed to send out two excitation signals of opposite polarities. These signals possess good consistency, high emission power, and precise signal adjustment. Lastly, the tool is tested in cased exploration wells in China. The experiment endings show that about 90% of the casing waves are canceled. By suppressing the casing wave amplitude, the cased-hole acoustic logging can be used commercially to obtain trustworthy formation information.
Open AccessDesign of an Acoustic Through-Casing Logging Tool
Well logging is performed in oil and gas exploration wells to obtain the physical characteristics of underground formations. Thereafter, these wells are cased. Through-casing logging is important in mature fields and for wells that are cased without logging due to borehole stability issues. Acoustic through-casing logging is a challenging issue due to the strong interference of casing waves in formation waves, especially when the casing and formation are poorly bonded. An acoustic tool with dual-source transmitters is developed, in which an additional transducer is added to suppress casing waves. First, the operation principle and the overall design of the tool are carried out, including the span distance between the two transmitting transducers and the spacing distance between the transmitting transducer and the receiving transducers. Thereafter, a dual-source transmitting circuit is designed to send out two excitation signals of opposite polarities. These signals possess good consistency, high emission power, and precise signal adjustment. Lastly, the tool is tested in cased exploration wells in China. The experiment endings show that about 90% of the casing waves are canceled. By suppressing the casing wave amplitude, the cased-hole acoustic logging can be used commercially to obtain trustworthy formation information.
- Open Access
Design of a New Acoustic Logging While Drilling Tool
To obtain qualified logging while drilling (LWD) data, a new acoustic LWD tool was designed. Its overall design is introduced here, including the physical construction, electronic structure, and operation flowchart. Thereafter, core technologies adopted in this tool are presented, such as dominant exciting wave bands of dipole source, a sine wave pulse excitation circuit, broadband impedance matching, and an intellectualized active reception transducer. Lastly, we tested this tool in the azimuthal anisotropy module well, calibration well, and normal well, working in the model of the cable, sliding eye, and logging while drilling. Experiments showed that the core technologies achieved ideal results and that the LWD tool obtained qualified data.
Open AccessDesign of a New Acoustic Logging While Drilling Tool
To obtain qualified logging while drilling (LWD) data, a new acoustic LWD tool was designed. Its overall design is introduced here, including the physical construction, electronic structure, and operation flowchart. Thereafter, core technologies adopted in this tool are presented, such as dominant exciting wave bands of dipole source, a sine wave pulse excitation circuit, broadband impedance matching, and an intellectualized active reception transducer. Lastly, we tested this tool in the azimuthal anisotropy module well, calibration well, and normal well, working in the model of the cable, sliding eye, and logging while drilling. Experiments showed that the core technologies achieved ideal results and that the LWD tool obtained qualified data.