Akila K El Morsi1
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Akila K El Morsi1 has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Mohammed F. Menoufy
Egyptian Petroleum Research Institute, Nasr City, Cairo, Egypt
3 shared publications - Mohammed Saber Gad
Mechanical Engineering Department, Faculty of Engineering, Fayoum University, Fayoum, Egypt
3 shared publications - Nagwa El Ibiari
Chemical Engineering & Pilot Plant Department, National Research Centre, El Buhouth St., Dokki, Egypt
3 shared publications A.K. Aboul-Gheit
2 shared publications- Ashraf Amin
Chemical Engineering and Pilot Plant Department, Engineering and Renewable Energy Research Institute, National Research Centre, Dokki, Giza 12622, Egypt
2 shared publications G.I. El-Diwani
2 shared publications
Latest Publications
- Top Cited PapersOpen Access
- 1 June 2019
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 28 (2) , 183-188
Effect of biodiesel fuels on diesel engine emissions
- 1 June 2019
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 28 (2) , 183-188
Top Cited PapersOpen AccessEffect of biodiesel fuels on diesel engine emissions
- Top Cited PapersOpen Access
- 1 December 2018
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 27 (4) , 985-989
Effect of waste cooking-oil biodiesel on performance and exhaust emissions of a diesel engine
- 1 December 2018
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 27 (4) , 985-989
Top Cited PapersOpen AccessEffect of waste cooking-oil biodiesel on performance and exhaust emissions of a diesel engine
- Open Access
- 1 June 2018
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 27 (2) , 215-219
Performance and emissions characteristics of C.I. engine fueled with palm oil/palm oil methyl ester blended with diesel fuel
- 1 June 2018
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 27 (2) , 215-219
Open AccessPerformance and emissions characteristics of C.I. engine fueled with palm oil/palm oil methyl ester blended with diesel fuel
- Open Access
- 1 June 2018
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 27 (2) , 187-194
Study on the characteristics of palm oil–biodiesel–diesel fuel blend
- 1 June 2018
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 27 (2) , 187-194
Open AccessStudy on the characteristics of palm oil–biodiesel–diesel fuel blend
- Open Access
- 14 August 2017
- Published by Gavin Publishers in Archives of Petroleum & Environmental Biotechnology
- Vol. 2 (3)
Treatment of Industrial Wastewater Contaminated byNitro Compounds
Journal of Petroleum and Environmental Biotechnology publishes new findings, technologies, methodologies in all areas of petroleum and environmental biotechnology, their commercial uses and exploitation, and current developments in the petroleum field.
- 14 August 2017
- Published by Gavin Publishers in Archives of Petroleum & Environmental Biotechnology
- Vol. 2 (3)
Open AccessTreatment of Industrial Wastewater Contaminated byNitro Compounds
Journal of Petroleum and Environmental Biotechnology publishes new findings, technologies, methodologies in all areas of petroleum and environmental biotechnology, their commercial uses and exploitation, and current developments in the petroleum field.
- Open Access
- 1 December 2016
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 25 (4) , 509-514
Experimental and empirical study of diesel and castor biodiesel blending effect, on kinematic viscosity, density and calorific value
This study aimed to investigate the fuel properties like density, viscosity and calorific value of trans-esterified methyl ester using castor biodiesel and their blends with No. 2 diesel. Empirical correlations are proposed to predict the kinematic viscosity, density, and calorific value for a mixture of castor oil and No. 2 diesel. Kay mixing rule shows a good prediction for the fuel properties under study. Several polynomials are fitted using least square method, and the fitted equations show a good agreement with the experimental data from our study. The developed equations could be used as universal formulas to predict the kinematic viscosity, density, and calorific value for castor oil and No. 2 diesel blend. The equations can be used to optimize the mixing ratio of the castor oil/No. 2 diesel for different applications. Blending of castor oil with No. 2 diesel- in the range of 20% castor oil, will not violate the required specification of diesel engines
- 1 December 2016
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 25 (4) , 509-514
Open AccessExperimental and empirical study of diesel and castor biodiesel blending effect, on kinematic viscosity, density and calorific value
This study aimed to investigate the fuel properties like density, viscosity and calorific value of trans-esterified methyl ester using castor biodiesel and their blends with No. 2 diesel. Empirical correlations are proposed to predict the kinematic viscosity, density, and calorific value for a mixture of castor oil and No. 2 diesel. Kay mixing rule shows a good prediction for the fuel properties under study. Several polynomials are fitted using least square method, and the fitted equations show a good agreement with the experimental data from our study. The developed equations could be used as universal formulas to predict the kinematic viscosity, density, and calorific value for castor oil and No. 2 diesel blend. The equations can be used to optimize the mixing ratio of the castor oil/No. 2 diesel for different applications. Blending of castor oil with No. 2 diesel- in the range of 20% castor oil, will not violate the required specification of diesel engines
- 2 May 2016
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 38 (9) , 1236-1245
Response surface methodology for carbon dioxide reforming of natural gas
The performance of 0.5% wt Rh/γ-AL2O3 catalyst for the dry reforming of natural gas using carbon dioxide has been studied. The response surface methodology (RSM) is used to study the effect of two different operating parameters, namely the hourly space velocity at the levels 18,000, 36,000, 45,000, and 60,000 ccg−1 h−1 and the reaction temperature at the levels 600, 700, and 800°C, on the conversion of the different components comprising commercial natural gas. The RSM is used to illustrate such effect in the three dimensions and shows the location of the optimum for the conversion or production of each component.
- 2 May 2016
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 38 (9) , 1236-1245
Response surface methodology for carbon dioxide reforming of natural gas
The performance of 0.5% wt Rh/γ-AL2O3 catalyst for the dry reforming of natural gas using carbon dioxide has been studied. The response surface methodology (RSM) is used to study the effect of two different operating parameters, namely the hourly space velocity at the levels 18,000, 36,000, 45,000, and 60,000 ccg−1 h−1 and the reaction temperature at the levels 600, 700, and 800°C, on the conversion of the different components comprising commercial natural gas. The RSM is used to illustrate such effect in the three dimensions and shows the location of the optimum for the conversion or production of each component.
- Open Access
- 1 June 2015
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 24 (2) , 145-154
Synthesis and characterization of polyurethane based on hydroxyl terminated polybutadiene and reinforced by carbon nanotubes
Nanocomposites consisting of multi wall carbon wall carbon nano tubes MWCNT/polyurethane (PU) had been successfully prepared based on hydroxy terminated polybutadiene HTPB and the prepared MWCNT. The effect of concentration of prepared MWCNT and surface modified CNT on the morphology, mechanical reinforcement, and thermal properties of PU-based composites had been evaluated by FESEM, tensile testing, thermo gravimetric analysis TGA and differential scanning calorimeter DSC.Polyurethane (PU) networks based on hydroxyl terminated polybutadiene (HTPB) and isophorone diisocyanate (IPDI) compound were prepared by a batch process. Two methods had been used to fabricate PU matrix/carbon nanotube nanocomposites: direct incorporation of unfunctional CNT (UCNT) into polymer matrices (noncovalent attachment) and in situ polymerization at their surface (covalent attachment).TGA showed a much better improvement of thermal stability of the composites than pure PU. Glass temperature (Tg) increased due to high interaction of CNT with PU. Also Young’s modulus increased. FESEM gave that the covalent attachment was better than noncovalent attachment for preparing PU/CNT composites
- 1 June 2015
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 24 (2) , 145-154
Open AccessSynthesis and characterization of polyurethane based on hydroxyl terminated polybutadiene and reinforced by carbon nanotubes
Nanocomposites consisting of multi wall carbon wall carbon nano tubes MWCNT/polyurethane (PU) had been successfully prepared based on hydroxy terminated polybutadiene HTPB and the prepared MWCNT. The effect of concentration of prepared MWCNT and surface modified CNT on the morphology, mechanical reinforcement, and thermal properties of PU-based composites had been evaluated by FESEM, tensile testing, thermo gravimetric analysis TGA and differential scanning calorimeter DSC.Polyurethane (PU) networks based on hydroxyl terminated polybutadiene (HTPB) and isophorone diisocyanate (IPDI) compound were prepared by a batch process. Two methods had been used to fabricate PU matrix/carbon nanotube nanocomposites: direct incorporation of unfunctional CNT (UCNT) into polymer matrices (noncovalent attachment) and in situ polymerization at their surface (covalent attachment).TGA showed a much better improvement of thermal stability of the composites than pure PU. Glass temperature (Tg) increased due to high interaction of CNT with PU. Also Young’s modulus increased. FESEM gave that the covalent attachment was better than noncovalent attachment for preparing PU/CNT composites
- Open Access
- 1 June 2014
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 23 (2) , 183-189
Study of the productivity of MWCNT over Fe and Fe–Co catalysts supported on SiO2, Al2O3 and MgO
In the present study, multi-walled carbon nanotubes (MWCNT) were prepared in good quality and quantity, MWCNT were produced using the catalytic chemical vapor deposition (CCVD) technique and the carbon source was acetylene. Different catalysts were synthesized based on iron and a mixture of iron and cobalt metal supported on SiO2, Al2O3 or MgO. The effect of parameters such as iron concentration, support type, bimetallic catalyst and the method of catalyst preparation has been investigated in the production of MWCNT. The quality of as-made nanotubes was investigated by the high-resolution transmission electron microscopy (HRTEM) and thermogravimetric analysis (TGA). The best yield of MWCNT was 30 times of the amount of the used catalyst. The high yield of MWCNT was gained by 40wt.% Fe on alumina support which was prepared by the sol–gel method. TEM analysis was done for the carbon deposit, which revealed that the walls of the MWCNT were graphitized, with regular inner channel and uniform diameter. It reflected a reasonable degree of purity. The TGA showed that MWCNT was decomposed at 635°C by a small rate indicating a high thermal stability and well crystalline formation of the produced MWCNT
- 1 June 2014
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 23 (2) , 183-189
Open AccessStudy of the productivity of MWCNT over Fe and Fe–Co catalysts supported on SiO2, Al2O3 and MgO
In the present study, multi-walled carbon nanotubes (MWCNT) were prepared in good quality and quantity, MWCNT were produced using the catalytic chemical vapor deposition (CCVD) technique and the carbon source was acetylene. Different catalysts were synthesized based on iron and a mixture of iron and cobalt metal supported on SiO2, Al2O3 or MgO. The effect of parameters such as iron concentration, support type, bimetallic catalyst and the method of catalyst preparation has been investigated in the production of MWCNT. The quality of as-made nanotubes was investigated by the high-resolution transmission electron microscopy (HRTEM) and thermogravimetric analysis (TGA). The best yield of MWCNT was 30 times of the amount of the used catalyst. The high yield of MWCNT was gained by 40wt.% Fe on alumina support which was prepared by the sol–gel method. TEM analysis was done for the carbon deposit, which revealed that the walls of the MWCNT were graphitized, with regular inner channel and uniform diameter. It reflected a reasonable degree of purity. The TGA showed that MWCNT was decomposed at 635°C by a small rate indicating a high thermal stability and well crystalline formation of the produced MWCNT
- 1 September 2009
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 521-522, 397-400
Development of a nickel–polymer composite by using friendly environmental polymeric surfactant
- 1 September 2009
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 521-522, 397-400
Development of a nickel–polymer composite by using friendly environmental polymeric surfactant