Hua Hou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hua Hou has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
- Yuhong Zhao
School of Materials Science and Engineering, Collaborative Innovation Center of Ministry of Education and Shanxi Province for High-Performance Al/Mg Alloy Materials, North University of China, Taiyuan, China
15 shared publications - Baoshan Wang
College of Chemistry and Molecular Sciences Wuhan University Wuhan China
4 shared publications - Ruifeng Dong
North University of China
4 shared publications Chenhui Li
3 shared publicationsJianhui Jing
3 shared publicationsKaixin Sun
3 shared publications
Latest Publications
- Open Access
- 17 October 2026
- Published by Elsevier in SSRN Electronic Journal
Achieving synergistic strength-ductility enhancement in Ti-6Al-4V alloys through defect mitigation during selective laser melting
Understanding microstructural evolution and defect formation mechanisms during selective laser melting (SLM) is essential for optimizing mechanical properties. This study focuses on the effects of processing conditions at different energy densities on microstructural evolution and mechanical properties. At low energy input, insufficient melting leads to unmelted powder defects, and the accompanying high scanning speed causes grain coarsening and grain-boundary bending. Excessive energy input also coarsens grains, elevates grain boundary energy, and triggers solidification defects. To mitigate these problems, this study adopts a strategy of reducing energy input while ensuring complete powder melting. This approach effectively suppresses defects, refines the initially coarse-grained microstructure, and overcomes the strength-ductility mismatch. The results indicate that the defect mitigation forces cracks to propagate transgranularly via microvoid coalescence. The cracks follow a tortuous path that dissipates more energy, thereby significantly delaying fracture and enhancing ductility. In addition to defect suppression, the refined α′ martensite laths and the fine nano‐twins within them further contribute to the strength improvement. The synergistic effect of defect mitigation and microstructural refinement thus yields a combination of high strength and ductility.
- 17 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAchieving synergistic strength-ductility enhancement in Ti-6Al-4V alloys through defect mitigation during selective laser melting
Understanding microstructural evolution and defect formation mechanisms during selective laser melting (SLM) is essential for optimizing mechanical properties. This study focuses on the effects of processing conditions at different energy densities on microstructural evolution and mechanical properties. At low energy input, insufficient melting leads to unmelted powder defects, and the accompanying high scanning speed causes grain coarsening and grain-boundary bending. Excessive energy input also coarsens grains, elevates grain boundary energy, and triggers solidification defects. To mitigate these problems, this study adopts a strategy of reducing energy input while ensuring complete powder melting. This approach effectively suppresses defects, refines the initially coarse-grained microstructure, and overcomes the strength-ductility mismatch. The results indicate that the defect mitigation forces cracks to propagate transgranularly via microvoid coalescence. The cracks follow a tortuous path that dissipates more energy, thereby significantly delaying fracture and enhancing ductility. In addition to defect suppression, the refined α′ martensite laths and the fine nano‐twins within them further contribute to the strength improvement. The synergistic effect of defect mitigation and microstructural refinement thus yields a combination of high strength and ductility.
- Open Access
- 15 August 2026
- Published by Elsevier in SSRN Electronic Journal
Achieving synergistic strength-ductility enhancement in Ti-6Al-4V alloys through defect mitigation during selective laser melting
Understanding microstructural evolution and defect formation mechanisms during selective laser melting (SLM) is essential for optimizing mechanical properties. This study focuses on the effects of processing conditions at different energy densities on microstructural evolution and mechanical properties. At low energy input, insufficient melting leads to unmelted powder defects, and the accompanying high scanning speed causes grain coarsening and grain-boundary bending. Excessive energy input also coarsens grains, elevates grain boundary energy, and triggers solidification defects. To mitigate these problems, this study adopts a strategy of reducing energy input while ensuring complete powder melting. This approach effectively suppresses defects, refines the initially coarse-grained microstructure, and overcomes the strength-ductility mismatch. The results indicate that the defect mitigation forces cracks to propagate transgranularly via microvoid coalescence. The cracks follow a tortuous path that dissipates more energy, thereby significantly delaying fracture and enhancing ductility. In addition to defect suppression, the refined α′ martensite laths and the fine nano-twins within them further contribute to the strength improvement. The synergistic effect of defect mitigation and microstructural refinement thus yields a combination of high strength and ductility.
- 15 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAchieving synergistic strength-ductility enhancement in Ti-6Al-4V alloys through defect mitigation during selective laser melting
Understanding microstructural evolution and defect formation mechanisms during selective laser melting (SLM) is essential for optimizing mechanical properties. This study focuses on the effects of processing conditions at different energy densities on microstructural evolution and mechanical properties. At low energy input, insufficient melting leads to unmelted powder defects, and the accompanying high scanning speed causes grain coarsening and grain-boundary bending. Excessive energy input also coarsens grains, elevates grain boundary energy, and triggers solidification defects. To mitigate these problems, this study adopts a strategy of reducing energy input while ensuring complete powder melting. This approach effectively suppresses defects, refines the initially coarse-grained microstructure, and overcomes the strength-ductility mismatch. The results indicate that the defect mitigation forces cracks to propagate transgranularly via microvoid coalescence. The cracks follow a tortuous path that dissipates more energy, thereby significantly delaying fracture and enhancing ductility. In addition to defect suppression, the refined α′ martensite laths and the fine nano-twins within them further contribute to the strength improvement. The synergistic effect of defect mitigation and microstructural refinement thus yields a combination of high strength and ductility.
- Open Access
- 7 July 2026
- Published by Elsevier in SSRN Electronic Journal
Solute Distribution and Precipitate Formation Mechanism in Gradient Pressurized Squeeze Casting
The holding pressure stage is the key to improving the casting density and mechanical properties in the solidification process of squeeze casting. In squeeze casting, the use of a single holding pressure leads to segregation of the second phase. Therefore, an improved gradient-pressurized squeeze casting process has been proposed. By adjusting the holding pressure during the solidification stage, grain refinement under high pressure is achieved in the pre-solidification stage and the diffusion of solute elements is promoted after appropriate pressure relief in the later stage. This transforms the morphology of the second phase from a continuous mesh structure to particles and islands, ensuring the diffuse distribution of the second phase. The results show that gradient pressurized squeeze casting contributes more to the mechanical properties of the samples. The mechanical properties of the casting body samples reached 265MPa (room temperature)/106MPa (200°C), which is a combined result of refinement, second phase, and dislocation strengthening. Therefore, the gradient pressurized squeeze casting strategy is considered to be an effective process to improve the solute distribution and micro-morphological homogeneity within the squeeze casting components.
- 7 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSolute Distribution and Precipitate Formation Mechanism in Gradient Pressurized Squeeze Casting
The holding pressure stage is the key to improving the casting density and mechanical properties in the solidification process of squeeze casting. In squeeze casting, the use of a single holding pressure leads to segregation of the second phase. Therefore, an improved gradient-pressurized squeeze casting process has been proposed. By adjusting the holding pressure during the solidification stage, grain refinement under high pressure is achieved in the pre-solidification stage and the diffusion of solute elements is promoted after appropriate pressure relief in the later stage. This transforms the morphology of the second phase from a continuous mesh structure to particles and islands, ensuring the diffuse distribution of the second phase. The results show that gradient pressurized squeeze casting contributes more to the mechanical properties of the samples. The mechanical properties of the casting body samples reached 265MPa (room temperature)/106MPa (200°C), which is a combined result of refinement, second phase, and dislocation strengthening. Therefore, the gradient pressurized squeeze casting strategy is considered to be an effective process to improve the solute distribution and micro-morphological homogeneity within the squeeze casting components.
- Open Access
- 26 June 2026
- Published by Elsevier in SSRN Electronic Journal
Microstructural evolution and defect mitigation strategies in selective laser melting Ti-6Al-4V titanium alloy
Understanding defect formation mechanisms in selective laser melting is essential for enhancing product quality. This study investigates the microstructural evolution and defect formation mechanisms in Ti-6Al-4V (TC4) alloy under two processing conditions: repeated remelting and varying energy density (ED). The results show that during multiple remelting cycles, the laser does not fully penetrate the powder layer, leaving persistent defects at the bottom. Furthermore, repeated remelting concentrates excessive energy at the top of the powder layer, thereby promoting defect generation. Consequently, a large number of unmelted defects form at both the top and bottom of the powder layer. By contrast, increasing the ED enlarges the melt pool. However, excessive energy input simultaneously causes grain coarsening and elevates grain boundary energy, ultimately leading to solidification cracking. By reducing energy input while ensuring complete melting of the powder, this study demonstrates that defect formation can be suppressed under both processing conditions. This results in effective grain refinement. Consequently, a high-performance TC4 alloy with a synergistic strength-ductility improvement is obtained.
- 26 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMicrostructural evolution and defect mitigation strategies in selective laser melting Ti-6Al-4V titanium alloy
Understanding defect formation mechanisms in selective laser melting is essential for enhancing product quality. This study investigates the microstructural evolution and defect formation mechanisms in Ti-6Al-4V (TC4) alloy under two processing conditions: repeated remelting and varying energy density (ED). The results show that during multiple remelting cycles, the laser does not fully penetrate the powder layer, leaving persistent defects at the bottom. Furthermore, repeated remelting concentrates excessive energy at the top of the powder layer, thereby promoting defect generation. Consequently, a large number of unmelted defects form at both the top and bottom of the powder layer. By contrast, increasing the ED enlarges the melt pool. However, excessive energy input simultaneously causes grain coarsening and elevates grain boundary energy, ultimately leading to solidification cracking. By reducing energy input while ensuring complete melting of the powder, this study demonstrates that defect formation can be suppressed under both processing conditions. This results in effective grain refinement. Consequently, a high-performance TC4 alloy with a synergistic strength-ductility improvement is obtained.
- Open Access
- 2 June 2026
- Published by Elsevier in SSRN Electronic Journal
Stress‑Induced Dislocation and Grain‑Boundary Behaviors in Bimodal Heterogeneous Polycrystalline Copper: Experiments and Phase‑Field Crystal Study
The mechanical response of heterogeneous nanocrystalline materials is governed by the coupled behavior of dislocations and grain boundaries. In this study, three copper samples with distinct grain-size ratios were investigated using electron backscatter diffraction characterization combined with phase-field crystal (PFC) simulations to elucidate the intrinsic linkage between microstructural features and dislocation dynamics under room-temperature loading. Experiments reveal that the bimodal heterogeneous structure develops a high density of geometrically necessary dislocations at coarse-fine grain interfaces, generating hetero-deformation‑induced stress that enhances both strength and ductility. PFC simulations further provide an in‑situ view of the dislocation-grain-boundary interactions: the fine-grained region accommodates plastic deformation at the early strain stage through grain-boundary-mediated dislocation nucleation and absorption, thereby contributing to the initial ductility; in contrast, the coarse-grained region begins to continuously nucleate and accumulate dislocations from its boundaries after about 2.24% strain, leading to a monotonic increase and eventual saturation of dislocation density, which dominates the subsequent strain hardening and strength improvement. These findings may provide a mechanistic basis for designing heterogeneous copper with concurrently high strength and high ductility.
- 2 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessStress‑Induced Dislocation and Grain‑Boundary Behaviors in Bimodal Heterogeneous Polycrystalline Copper: Experiments and Phase‑Field Crystal Study
The mechanical response of heterogeneous nanocrystalline materials is governed by the coupled behavior of dislocations and grain boundaries. In this study, three copper samples with distinct grain-size ratios were investigated using electron backscatter diffraction characterization combined with phase-field crystal (PFC) simulations to elucidate the intrinsic linkage between microstructural features and dislocation dynamics under room-temperature loading. Experiments reveal that the bimodal heterogeneous structure develops a high density of geometrically necessary dislocations at coarse-fine grain interfaces, generating hetero-deformation‑induced stress that enhances both strength and ductility. PFC simulations further provide an in‑situ view of the dislocation-grain-boundary interactions: the fine-grained region accommodates plastic deformation at the early strain stage through grain-boundary-mediated dislocation nucleation and absorption, thereby contributing to the initial ductility; in contrast, the coarse-grained region begins to continuously nucleate and accumulate dislocations from its boundaries after about 2.24% strain, leading to a monotonic increase and eventual saturation of dislocation density, which dominates the subsequent strain hardening and strength improvement. These findings may provide a mechanistic basis for designing heterogeneous copper with concurrently high strength and high ductility.
- Open Access
- 19 May 2026
- Published by Elsevier in SSRN Electronic Journal
Solute segregation and crack sensitivity controlled by solidification phase transformation thermodynamics of niobium-containing steel
Different from conventional Fe-C low alloy steel, stainless steel has a high content of alloying elements, which leads to solidification solute segregation and phase transformation strain fluctuation, which seriously affects the quality of slab and hot working performance. Here, we consider the difference of thermodynamic and kinetic regulation between phase nucleation, phase transformation and microstructure defects caused by the difference of cooling rate of each part of the cross section during the cooling process of continuous casting billet. It is found that with the increase of cooling rate, the peritectic transformation process of S30432 exhibits three transformation modes similar to that of Fe-C low alloy steel, but the interface kinetic effect is obviously different, tending to massive transformation. The strong/weak thermodynamic and kinetic effects of different phase transition modes are derived from the interface temperature difference caused by undercooling and solute concentration gradient, as well as the difference in solute atom diffusion and interface migration rate. Combined with the solidification phase field model, the discharge mechanism of solute at the dendrite tip during solidification and the inhibition effect of solute trapping and ' dendrite → cell ' transition on solute segregation under the condition of high cooling rate were clarified. Furthermore, the liquid channel feeding sufficiency, dendrite coalescence, solute partitioning and interface interaction based on dislocation localization homogenization in γ-Fe matrix precisely regulates the lattice mismatch of γ-Fe/NbC and the strain fluctuation caused by massive transformation, which significantly reduces the solidification crack sensitivity.
- 19 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSolute segregation and crack sensitivity controlled by solidification phase transformation thermodynamics of niobium-containing steel
Different from conventional Fe-C low alloy steel, stainless steel has a high content of alloying elements, which leads to solidification solute segregation and phase transformation strain fluctuation, which seriously affects the quality of slab and hot working performance. Here, we consider the difference of thermodynamic and kinetic regulation between phase nucleation, phase transformation and microstructure defects caused by the difference of cooling rate of each part of the cross section during the cooling process of continuous casting billet. It is found that with the increase of cooling rate, the peritectic transformation process of S30432 exhibits three transformation modes similar to that of Fe-C low alloy steel, but the interface kinetic effect is obviously different, tending to massive transformation. The strong/weak thermodynamic and kinetic effects of different phase transition modes are derived from the interface temperature difference caused by undercooling and solute concentration gradient, as well as the difference in solute atom diffusion and interface migration rate. Combined with the solidification phase field model, the discharge mechanism of solute at the dendrite tip during solidification and the inhibition effect of solute trapping and ' dendrite → cell ' transition on solute segregation under the condition of high cooling rate were clarified. Furthermore, the liquid channel feeding sufficiency, dendrite coalescence, solute partitioning and interface interaction based on dislocation localization homogenization in γ-Fe matrix precisely regulates the lattice mismatch of γ-Fe/NbC and the strain fluctuation caused by massive transformation, which significantly reduces the solidification crack sensitivity.
- Open Access
- 13 March 2026
- Published by Elsevier in SSRN Electronic Journal
Synergistic enhancement of mechanical properties and corrosion resistance in a low stacking fault energy high-entropy alloy by introducing nanostructured surface layer and annealing
Low stacking fault energy (SFE) high-entropy alloys (HEAs) with enhanced mechanical and corrosion properties are promising candidates for demanding structural applications. In this work, a nanostructured surface layer was introduced into a Fe50Mn30Co10Cr10 HEA via shot peening, followed by short-time annealing at 800 oC. Tensile tests revealed that the shot-peened sample after annealing achieved a superior strength-ductility synergy. Moreover, it exhibited a significantly improved corrosion resistance in 3.5 wt.% NaCl solution. Microstructural analysis indicated that annealing promoted surface Mn segregation and its subsequent sacrificial dissolution during corrosion, which effectively removed active surface species and facilitated the formation of a dense, high-purity Cr2O3 passive film. The annealing-induced HCP to FCC phase transformation, defect recovery, and refinement of nanoplate structure simultaneously promoted the TRIP effect and interface strengthening, ultimately enhancing the mechanical properties. This work provides a feasible thermomechanical strategy for designing high-performance low-SFE HEAs through surface nanostructuring and annealing.
- 13 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSynergistic enhancement of mechanical properties and corrosion resistance in a low stacking fault energy high-entropy alloy by introducing nanostructured surface layer and annealing
Low stacking fault energy (SFE) high-entropy alloys (HEAs) with enhanced mechanical and corrosion properties are promising candidates for demanding structural applications. In this work, a nanostructured surface layer was introduced into a Fe50Mn30Co10Cr10 HEA via shot peening, followed by short-time annealing at 800 oC. Tensile tests revealed that the shot-peened sample after annealing achieved a superior strength-ductility synergy. Moreover, it exhibited a significantly improved corrosion resistance in 3.5 wt.% NaCl solution. Microstructural analysis indicated that annealing promoted surface Mn segregation and its subsequent sacrificial dissolution during corrosion, which effectively removed active surface species and facilitated the formation of a dense, high-purity Cr2O3 passive film. The annealing-induced HCP to FCC phase transformation, defect recovery, and refinement of nanoplate structure simultaneously promoted the TRIP effect and interface strengthening, ultimately enhancing the mechanical properties. This work provides a feasible thermomechanical strategy for designing high-performance low-SFE HEAs through surface nanostructuring and annealing.
- Open Access
- 10 March 2026
- Published by Elsevier in SSRN Electronic Journal
Segregation Formation Mechanism in Squeeze-Cast ZM5 Magnesium Alloy Baffles: Experimental Characterization and Phase-Field/EasyCast Simulations
As an energy-efficient and environmentally friendly molding technology, squeeze casting has gained significant attention and application. However, widespread segregation defects have significantly reduced the qualification rate of squeeze castings. The present investigation selected ZM5 magnesium alloy baffle as a representative specimens. This study systematically examines the effect of casting temperature on segregation characteristics and their peripheral microstructures. Experimental results reveal that aluminum(Al) enrichment induces solute segregation zones predominantly composed of Mg17Al12 intermetallic phase. In this study, the self-developed EasyCast software was integrated with the EPhase phase-field simulation tool to systematically simulate the state evolution of different regions during casting solidification, as well as the nucleation and growth behavior of grains in solute-enriched regions. The results elucidate the regulatory effects of solidification sequence differences and solute redistribution on microstructural evolution, thereby revealing the formation mechanism of segregation bands. The proposed methodology effectively addresses performance instability in squeeze-cast plates originating from segregation defects.
- 10 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSegregation Formation Mechanism in Squeeze-Cast ZM5 Magnesium Alloy Baffles: Experimental Characterization and Phase-Field/EasyCast Simulations
As an energy-efficient and environmentally friendly molding technology, squeeze casting has gained significant attention and application. However, widespread segregation defects have significantly reduced the qualification rate of squeeze castings. The present investigation selected ZM5 magnesium alloy baffle as a representative specimens. This study systematically examines the effect of casting temperature on segregation characteristics and their peripheral microstructures. Experimental results reveal that aluminum(Al) enrichment induces solute segregation zones predominantly composed of Mg17Al12 intermetallic phase. In this study, the self-developed EasyCast software was integrated with the EPhase phase-field simulation tool to systematically simulate the state evolution of different regions during casting solidification, as well as the nucleation and growth behavior of grains in solute-enriched regions. The results elucidate the regulatory effects of solidification sequence differences and solute redistribution on microstructural evolution, thereby revealing the formation mechanism of segregation bands. The proposed methodology effectively addresses performance instability in squeeze-cast plates originating from segregation defects.
- Open Access
- 6 March 2026
- Published by Elsevier in SSRN Electronic Journal
The Effect of the Stability of Passive Films on the Surface of High-Nitrogen Martensitic Stainless Steel Cronidur 30 in Acidic Environments on Its Pitting Initiation and Propagation Behavior
Pitting corrosion of stainless steel, a critical failure mode in aggressive environments, commonly initiates at inclusions, driven by local acidification and subsequent passive film dissolution. However, the quantitative link between passive film acid resistance and pitting initiation/propagation remains poorly understood. This study systematically investigated the effect of passive film acid resistance on the pitting behavior of Cronidur 30 high-nitrogen martensitic stainless steel (HNMSS) under different tempering times via critical pH tests, in-situ pitting observation, and colorimetric pH visualization. The critical pH of passive film stability increased from <1 (cryogenically treated sample) to 3.5–4 (tempered for ≥5 h), indicating degraded acid resistance with prolonged tempering, which correlated negatively with pitting susceptibility (decreased pitting potential). Critical pH values also defined the upper pH limit inside pits. In-situ experiments revealed that the cryogenically treated sample with acid-resistant passive film exhibited deep, localized pitting, while the 100 h-tempered sample with poor acid resistance suffered passive film destruction in Cr-depleted zones around Cr2 N, causing lateral pitting spread and large shallow pits. This work demonstrates that passive film acid resistance is a key factor governing pitting initiation susceptibility and propagation morphology of HNMSS, providing critical insights for designing corrosion-resistant stainless steels.
- 6 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessThe Effect of the Stability of Passive Films on the Surface of High-Nitrogen Martensitic Stainless Steel Cronidur 30 in Acidic Environments on Its Pitting Initiation and Propagation Behavior
Pitting corrosion of stainless steel, a critical failure mode in aggressive environments, commonly initiates at inclusions, driven by local acidification and subsequent passive film dissolution. However, the quantitative link between passive film acid resistance and pitting initiation/propagation remains poorly understood. This study systematically investigated the effect of passive film acid resistance on the pitting behavior of Cronidur 30 high-nitrogen martensitic stainless steel (HNMSS) under different tempering times via critical pH tests, in-situ pitting observation, and colorimetric pH visualization. The critical pH of passive film stability increased from <1 (cryogenically treated sample) to 3.5–4 (tempered for ≥5 h), indicating degraded acid resistance with prolonged tempering, which correlated negatively with pitting susceptibility (decreased pitting potential). Critical pH values also defined the upper pH limit inside pits. In-situ experiments revealed that the cryogenically treated sample with acid-resistant passive film exhibited deep, localized pitting, while the 100 h-tempered sample with poor acid resistance suffered passive film destruction in Cr-depleted zones around Cr2 N, causing lateral pitting spread and large shallow pits. This work demonstrates that passive film acid resistance is a key factor governing pitting initiation susceptibility and propagation morphology of HNMSS, providing critical insights for designing corrosion-resistant stainless steels.
- Open Access
- 3 March 2026
- Published by Elsevier in SSRN Electronic Journal
GO-Activated Thermal Treatment Response Mechanism in Magnesium Matrix Composites
The regulation of the second-phase diffusion behavior of the reinforcement during heat treatment is crucial for determining the properties of magnesium matrix composites. In this study, magnesium matrix composites reinforced with varying contents of graphene oxide (GO) were prepared using a surface treatment combined with the squeeze casting process. Additionally, the phase-field method was employed to simulate the precipitation phases in GO-containing polycrystalline magnesium matrix materials. The results demonstrate that GO can be uniformly dispersed within the magnesium matrix and effectively regulates the diffusion of the second phase during subsequent heat treatment through a dual mechanism: on the one hand, GO significantly refines the grains by pinning grain boundaries and increasing the density of small-angle grain boundaries; on the other hand, the lattice mismatch between GO and the magnesium matrix induces the formation of an interfacial dislocation network, which provides a rapid channel for atomic diffusion and synergistically promotes the dissolution and precipitation of the second phase. When the GO content is 0.6 wt%, the yield strength of the composite after aging treatment reaches 192.2 MPa, with a Vickers hardness of 110.6 HV. The microstructure of the materials, optimized through heat treatment parameters, exhibits finer and more uniform characteristics, providing a significant theoretical basis and technical support for the development and application of magnesium matrix composites.
- 3 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessGO-Activated Thermal Treatment Response Mechanism in Magnesium Matrix Composites
The regulation of the second-phase diffusion behavior of the reinforcement during heat treatment is crucial for determining the properties of magnesium matrix composites. In this study, magnesium matrix composites reinforced with varying contents of graphene oxide (GO) were prepared using a surface treatment combined with the squeeze casting process. Additionally, the phase-field method was employed to simulate the precipitation phases in GO-containing polycrystalline magnesium matrix materials. The results demonstrate that GO can be uniformly dispersed within the magnesium matrix and effectively regulates the diffusion of the second phase during subsequent heat treatment through a dual mechanism: on the one hand, GO significantly refines the grains by pinning grain boundaries and increasing the density of small-angle grain boundaries; on the other hand, the lattice mismatch between GO and the magnesium matrix induces the formation of an interfacial dislocation network, which provides a rapid channel for atomic diffusion and synergistically promotes the dissolution and precipitation of the second phase. When the GO content is 0.6 wt%, the yield strength of the composite after aging treatment reaches 192.2 MPa, with a Vickers hardness of 110.6 HV. The microstructure of the materials, optimized through heat treatment parameters, exhibits finer and more uniform characteristics, providing a significant theoretical basis and technical support for the development and application of magnesium matrix composites.