Muhammad Awais
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Muhammad Awais has a total of 83 co-authors. Here are the top co-authors by number of shared publications:
Allan Walton
7 shared publications- Awais Ikram
Faculty of Mechanical Engineering, University of Ljubljana, Aškerčeva cesta 6, SI-1000 Ljubljana, Slovenia
5 shared publications - Richard Stuart Sheridan
School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham B15 2TT, UK
5 shared publications - Allan Walton
School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham B15 2TT, UK
4 shared publications - Neil Anthony Rowson
School of Chemical Engineering, University of Birmingham, Edgbaston, Birmingham B15 2TT, UK
4 shared publications C. Marion
3 shared publications
Latest Publications
- Open Access
- 30 October 2025
- Published by Elsevier in Sustainable Materials and Technologies
- Vol. 46
Improving short-loop recycling of sintered NdFeB magnets by grain boundary phase separation following hydrogen processing
- 30 October 2025
- Published by Elsevier in Sustainable Materials and Technologies
- Vol. 46
Open AccessImproving short-loop recycling of sintered NdFeB magnets by grain boundary phase separation following hydrogen processing
- 7 June 2024
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 603
Hydrogen-assisted recycling of Nd-Fe-B magnets from the end-of-life audio products
- 7 June 2024
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 603
Hydrogen-assisted recycling of Nd-Fe-B magnets from the end-of-life audio products
- Open Access
- 18 October 2023
- Published by Elsevier in Powder Technology
- Vol. 431
Development of anisotropic Nd-Fe-B powder from isotropic gas atomized powder
- 18 October 2023
- Published by Elsevier in Powder Technology
- Vol. 431
Open AccessDevelopment of anisotropic Nd-Fe-B powder from isotropic gas atomized powder
- Open Access
- 7 February 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (4) , 2998
A Critical Analysis of the Energy Requirements of a Commercial Building Based on Various Types of Glass Insulations
Heat loss through the building envelope comprises air leaks through the cracks and largely through the windows, which is the weakest link of the thermal envelope. Therefore, it is necessary to devise a systematic approach to analyze the rightful selection of glass for buildings. The investigation is to analyze the energy-saving potential of different glasses and their comparisons to the initial capital cost to find the payback time in terms of energy saving by using two different types of equipment. The quantitative simulation study was completed on the Hourly Analysis Program (HAP) to analyze the annual energy consumption of the HVAC system for seven glasses and two types of chilled water equipment. The results show that the performance glasses with a tint had better efficiency in terms of energy saving, with a payback time of 3–7 months. A comparison of all glasses illustrated that float glass contributes the most to the total cooling load among all glasses, which were 5.04%, 5.7%, 7.6%, and 8.9% for the N, S, E, and W orientations, respectively. Moreover, the lowest contribution of glass to the total cooling load was given by tinted double-glazed glass, which was 2%, 2.3%, 3.0%, and 3.01% for N, S, E, and W orientations, respectively.
- 7 February 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (4) , 2998
Open AccessA Critical Analysis of the Energy Requirements of a Commercial Building Based on Various Types of Glass Insulations
Heat loss through the building envelope comprises air leaks through the cracks and largely through the windows, which is the weakest link of the thermal envelope. Therefore, it is necessary to devise a systematic approach to analyze the rightful selection of glass for buildings. The investigation is to analyze the energy-saving potential of different glasses and their comparisons to the initial capital cost to find the payback time in terms of energy saving by using two different types of equipment. The quantitative simulation study was completed on the Hourly Analysis Program (HAP) to analyze the annual energy consumption of the HVAC system for seven glasses and two types of chilled water equipment. The results show that the performance glasses with a tint had better efficiency in terms of energy saving, with a payback time of 3–7 months. A comparison of all glasses illustrated that float glass contributes the most to the total cooling load among all glasses, which were 5.04%, 5.7%, 7.6%, and 8.9% for the N, S, E, and W orientations, respectively. Moreover, the lowest contribution of glass to the total cooling load was given by tinted double-glazed glass, which was 2%, 2.3%, 3.0%, and 3.01% for N, S, E, and W orientations, respectively.
- Open Access
- 23 January 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (3) , 2137
Techno-Economic-Environmental Assessment of an Isolated Rural Micro-Grid from a Mid-Career Repowering Perspective
Pakistan is an energy deficient country with depleting energy reserves and increasing energy demand. Due to excessive population growth, the domestic and commercial energy sectors are experiencing rising demand. To meet the requisite demand, renewables are favored rather than conventional counterparts. In this study, we model hybrid power systems using solar, wind and biomass resources for electrifying remote areas. The four locations are chosen for the study around a developing country, Pakistan, where each site is designed according to an isolated microgrid with maximum indigenous resources potential as per the requisite demands. A survey is conducted for the load demand and biomass availability. Optimization is conducted across objectives of minimum levelized cost of the generated energy, least the net present cost and lesser payback period. The optimal results were achieved in-terms of required objectives across southern sites as compared to northern counterparts. The cost of generated energy is comparable to grid electricity and ensures 24 h power supply without cut off and load shedding to the un-electrified rural area. The hybrid power system has a low carbon footprint across emissions due to the use of renewable resources. All the estimated load of rural communities is met with the available resources and mid-career impact has also been conducted across 10 years of the project life to fulfill the increasing load demand of the communities after installation. The results are validated via comparative analysis and show the effectiveness of the proposed study.
- 23 January 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (3) , 2137
Open AccessTechno-Economic-Environmental Assessment of an Isolated Rural Micro-Grid from a Mid-Career Repowering Perspective
Pakistan is an energy deficient country with depleting energy reserves and increasing energy demand. Due to excessive population growth, the domestic and commercial energy sectors are experiencing rising demand. To meet the requisite demand, renewables are favored rather than conventional counterparts. In this study, we model hybrid power systems using solar, wind and biomass resources for electrifying remote areas. The four locations are chosen for the study around a developing country, Pakistan, where each site is designed according to an isolated microgrid with maximum indigenous resources potential as per the requisite demands. A survey is conducted for the load demand and biomass availability. Optimization is conducted across objectives of minimum levelized cost of the generated energy, least the net present cost and lesser payback period. The optimal results were achieved in-terms of required objectives across southern sites as compared to northern counterparts. The cost of generated energy is comparable to grid electricity and ensures 24 h power supply without cut off and load shedding to the un-electrified rural area. The hybrid power system has a low carbon footprint across emissions due to the use of renewable resources. All the estimated load of rural communities is met with the available resources and mid-career impact has also been conducted across 10 years of the project life to fulfill the increasing load demand of the communities after installation. The results are validated via comparative analysis and show the effectiveness of the proposed study.
- 1 December 2020
- Published by Elsevier in Journal of Cleaner Production
- Vol. 277
The extraction of NdFeB magnets from automotive scrap rotors using hydrogen
- 1 December 2020
- Published by Elsevier in Journal of Cleaner Production
- Vol. 277
The extraction of NdFeB magnets from automotive scrap rotors using hydrogen
- Open Access
Limitations in the Grain Boundary Processing of the Recycled HDDR Nd-Fe-B System
Fully dense spark plasma sintered recycled and fresh HDDR Nd-Fe-B nanocrystalline bulk magnets were processed by surface grain boundary diffusion (GBD) treatment to further augment the coercivity and investigate the underlying diffusion mechanism. The fully dense SPS processed HDDR based magnets were placed in a crucible with varying the eutectic alloys Pr68Cu32 and Dy70Cu30 at 2–20 wt. % as direct diffusion source above the ternary transition temperature for GBD processing followed by secondary annealing. The changes in mass gain was analyzed and weighted against the magnetic properties. For the recycled magnet, the coercivity (HCi) values obtained after optimal GBDP yielded ~60% higher than the starting recycled HDDR powder and 17.5% higher than the SPS-ed processed magnets. The fresh MF-15P HDDR Nd-Fe-B based magnets gained 25–36% higher coercivities with Pr-Cu GBDP. The FEG-SEM investigation provided insight on the diffusion depth and EDXS analysis indicated the changes in matrix and intergranular phase composition within the diffusion zone. The mechanism of surface to grain boundary diffusion and the limitations to thorough grain boundary diffusion in the HDDR Nd-Fe-B based bulk magnets were detailed in this study.
Open AccessLimitations in the Grain Boundary Processing of the Recycled HDDR Nd-Fe-B System
Fully dense spark plasma sintered recycled and fresh HDDR Nd-Fe-B nanocrystalline bulk magnets were processed by surface grain boundary diffusion (GBD) treatment to further augment the coercivity and investigate the underlying diffusion mechanism. The fully dense SPS processed HDDR based magnets were placed in a crucible with varying the eutectic alloys Pr68Cu32 and Dy70Cu30 at 2–20 wt. % as direct diffusion source above the ternary transition temperature for GBD processing followed by secondary annealing. The changes in mass gain was analyzed and weighted against the magnetic properties. For the recycled magnet, the coercivity (HCi) values obtained after optimal GBDP yielded ~60% higher than the starting recycled HDDR powder and 17.5% higher than the SPS-ed processed magnets. The fresh MF-15P HDDR Nd-Fe-B based magnets gained 25–36% higher coercivities with Pr-Cu GBDP. The FEG-SEM investigation provided insight on the diffusion depth and EDXS analysis indicated the changes in matrix and intergranular phase composition within the diffusion zone. The mechanism of surface to grain boundary diffusion and the limitations to thorough grain boundary diffusion in the HDDR Nd-Fe-B based bulk magnets were detailed in this study.
- Open Access
Spark Plasma Sintering as an Effective Texturing Tool for Reprocessing Recycled HDDR Nd-Fe-B Magnets with Lossless Coercivity
The low-pressure hot-deformation methodology was applied to reprocess the nanocrystalline hydrogenation–disproportionation–desorption–recombination (HDDR) Nd-Fe-B powders from end-of-life (EOL) permanent magnets’ waste to determine the mechanism of texture development and the resultant improvement in remanence (and BHmax) in the recycled material. Both the hot-pressed and hot-deformed magnets produced via spark plasma sintering (SPS) were compared in terms of their magnetic properties with respect to forging pressures. Also, a comparison was established with the microstructure to cite the effectiveness of texture development at low deformation rates and pressures which is pivotal for retaining high coercivity. The hot-pressed magnets maintain the high coercivity (better than 100%) of the original recycled powder due to the control of SPS conditions. The hot deformation pressure was varied from 100–150 MPa at 750 °C processing temperature to identify the optimal texture development in the sintered HDDR Nd-Fe-B magnets. The effect of post-hot-deformation thermal treatment was also investigated, which helped in boosting the overall magnetic properties and better than the recycled feedstock. This low-pressure hot deformation process improved the remanence of the hot-pressed magnet by 11% over the starting recycled powder. The Mr/MS ratio which was 0.5 for the hot-pressed magnets increased to 0.64 for the magnets hot-deformed at 150 MPa. Also, a 55% reduction in height of the sample was achieved with the c-axis texture, indicating approximately 23% higher remanence over the isotropic hot-pressed magnets. After hot deformation, the intrinsic coercivity (HCi) of 960 kA/m and the remanence (Br) value of 1.01 T at 150 MPa is indicative that the controlled SPS reprocessing technique can prevent microstructure related losses in the magnetic properties of the recycled materials. This route also suggests that the scrap Nd-Fe-B magnets can be treated with recoverable magnetic properties subsequently via HDDR technique and controlled hot deformation with a follow-up annealing.
Open AccessSpark Plasma Sintering as an Effective Texturing Tool for Reprocessing Recycled HDDR Nd-Fe-B Magnets with Lossless Coercivity
The low-pressure hot-deformation methodology was applied to reprocess the nanocrystalline hydrogenation–disproportionation–desorption–recombination (HDDR) Nd-Fe-B powders from end-of-life (EOL) permanent magnets’ waste to determine the mechanism of texture development and the resultant improvement in remanence (and BHmax) in the recycled material. Both the hot-pressed and hot-deformed magnets produced via spark plasma sintering (SPS) were compared in terms of their magnetic properties with respect to forging pressures. Also, a comparison was established with the microstructure to cite the effectiveness of texture development at low deformation rates and pressures which is pivotal for retaining high coercivity. The hot-pressed magnets maintain the high coercivity (better than 100%) of the original recycled powder due to the control of SPS conditions. The hot deformation pressure was varied from 100–150 MPa at 750 °C processing temperature to identify the optimal texture development in the sintered HDDR Nd-Fe-B magnets. The effect of post-hot-deformation thermal treatment was also investigated, which helped in boosting the overall magnetic properties and better than the recycled feedstock. This low-pressure hot deformation process improved the remanence of the hot-pressed magnet by 11% over the starting recycled powder. The Mr/MS ratio which was 0.5 for the hot-pressed magnets increased to 0.64 for the magnets hot-deformed at 150 MPa. Also, a 55% reduction in height of the sample was achieved with the c-axis texture, indicating approximately 23% higher remanence over the isotropic hot-pressed magnets. After hot deformation, the intrinsic coercivity (HCi) of 960 kA/m and the remanence (Br) value of 1.01 T at 150 MPa is indicative that the controlled SPS reprocessing technique can prevent microstructure related losses in the magnetic properties of the recycled materials. This route also suggests that the scrap Nd-Fe-B magnets can be treated with recoverable magnetic properties subsequently via HDDR technique and controlled hot deformation with a follow-up annealing.
- Open Access
- 1 January 2020
- Published by Elsevier in Journal of Rare Earths
- Vol. 38 (1) , 90-99
Particle size dependent sinterability and magnetic properties of recycled HDDR Nd–Fe–B powders consolidated with spark plasma sintering
- 1 January 2020
- Published by Elsevier in Journal of Rare Earths
- Vol. 38 (1) , 90-99
Open AccessParticle size dependent sinterability and magnetic properties of recycled HDDR Nd–Fe–B powders consolidated with spark plasma sintering
- Open Access
Coercivity Increase of the Recycled HDDR Nd-Fe-B Powders Doped with DyF3 and Processed via Spark Plasma Sintering & the Effect of Thermal Treatments
The magnetic properties of the recycled hydrogenation disproportionation desorption recombination (HDDR) Nd-Fe-B powder, doped with a low weight fraction of DyF3 nanoparticles, were investigated. Spark plasma sintering (SPS) was used to consolidate the recycled Nd-Fe-B powder blends containing 1, 2, and 5 wt.% of DyF3 grounded powder. Different post-SPS sintering thermal treatment conditions (600, 750, and 900 °C), for a varying amount of time, were studied in view of optimizing the magnetic properties and developing characteristic core-shell microstructure in the HDDR powder. As received, recycled HDDR powder has coercivity (HCi) of 830 kA/m, and as optimally as SPS magnets reach 1160 kA/m, after the thermal treatment. With only 1–2 wt.% blended DyF3, the HCi peaked to 1407 kA/m with the thermal treatment at 750 °C for 1 h. The obtained HCi values of the blend magnet is ~69.5% higher than the starting recycled HDDR powder and 17.5% higher than the SPS processed magnet annealed at 750 °C for 1 h. Prolonging the thermal treatment time to 6 h and temperature conditions above 900 °C was detrimental to the magnetic properties. About ~2 wt.% DyF3 dopant was suitable to develop a uniform core-shell microstructure in the HDDR Nd-Fe-B powder. The Nd-rich phase in the HDDR powder has a slightly different and fluorine rich composition i.e., Nd-O-F2 than in the one reported in sintered magnets (Nd-O-F). The composition of reaction zone-phases after the thermal treatment and Dy diffusion was DyF4, which is more abundant in 5 wt.% doped samples. Further doping above 2 wt.% DyF3 is ineffective in augmenting the coercivity of the recycled HDDR powder, due to the decomposition of the shell structure and formation of non-ferromagnetic rare earth-based complex intermetallic compounds. The DyF3 doping is a very effective single step route in a controlled coercivity improvement of the recycled HDDR Nd-Fe-B powder from the end of life magnetic products.
Open AccessCoercivity Increase of the Recycled HDDR Nd-Fe-B Powders Doped with DyF3 and Processed via Spark Plasma Sintering & the Effect of Thermal Treatments
The magnetic properties of the recycled hydrogenation disproportionation desorption recombination (HDDR) Nd-Fe-B powder, doped with a low weight fraction of DyF3 nanoparticles, were investigated. Spark plasma sintering (SPS) was used to consolidate the recycled Nd-Fe-B powder blends containing 1, 2, and 5 wt.% of DyF3 grounded powder. Different post-SPS sintering thermal treatment conditions (600, 750, and 900 °C), for a varying amount of time, were studied in view of optimizing the magnetic properties and developing characteristic core-shell microstructure in the HDDR powder. As received, recycled HDDR powder has coercivity (HCi) of 830 kA/m, and as optimally as SPS magnets reach 1160 kA/m, after the thermal treatment. With only 1–2 wt.% blended DyF3, the HCi peaked to 1407 kA/m with the thermal treatment at 750 °C for 1 h. The obtained HCi values of the blend magnet is ~69.5% higher than the starting recycled HDDR powder and 17.5% higher than the SPS processed magnet annealed at 750 °C for 1 h. Prolonging the thermal treatment time to 6 h and temperature conditions above 900 °C was detrimental to the magnetic properties. About ~2 wt.% DyF3 dopant was suitable to develop a uniform core-shell microstructure in the HDDR Nd-Fe-B powder. The Nd-rich phase in the HDDR powder has a slightly different and fluorine rich composition i.e., Nd-O-F2 than in the one reported in sintered magnets (Nd-O-F). The composition of reaction zone-phases after the thermal treatment and Dy diffusion was DyF4, which is more abundant in 5 wt.% doped samples. Further doping above 2 wt.% DyF3 is ineffective in augmenting the coercivity of the recycled HDDR powder, due to the decomposition of the shell structure and formation of non-ferromagnetic rare earth-based complex intermetallic compounds. The DyF3 doping is a very effective single step route in a controlled coercivity improvement of the recycled HDDR Nd-Fe-B powder from the end of life magnetic products.