ZMZhuowu Men

Zhuowu Men

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zhuowu Men has a total of 63 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Top Cited Papers
    Open Access

    Efficient conversion of syngas to linear α-olefins by phase-pure χ-Fe5C2

    by Peng Wang, Fu-Kuo Chiang, Jiachun Chai, A. Iulian Dugulan, Juan Dong, Wei Chen, Robin J. P. Broos, Bo Feng, Yuanjun Song, Yijun Lv, et al.

    Oil has long been the dominant feedstock for producing fuels and chemicals, but coal, natural gas and biomass are increasingly explored alternatives1–3. Their conversion first generates syngas, a mixture of CO and H2, which is then processed further using Fischer–Tropsch (FT) chemistry. However, although commercial FT technology for fuel production is established, using it to access valuable chemicals remains challenging. A case in point is linear α-olefins (LAOs), which are important chemical intermediates obtained by ethylene oligomerization at present4–8. The commercial high-temperature FT process and the FT-to-olefin process under development at present both convert syngas directly to LAOs, but also generate much CO2 waste that leads to a low carbon utilization efficiency9–14. The efficiency is further compromised by substantially fewer of the converted carbon atoms ending up as valuable C5–C10 LAOs than are found in the C2–C4 olefins that dominate the product mixtures9–14. Here we show that the use of the original phase-pure χ-iron carbide can minimize these syngas conversion problems: tailored and optimized for the process of FT to LAOs, this catalyst exhibits an activity at 290 °C that is 1–2 orders higher than dedicated FT-to-olefin catalysts can achieve above 320 °C (refs. 12–15), is stable for 200 h, and produces desired C2–C10 LAOs and unwanted CO2 with carbon-based selectivities of 51% and 9% under industrially relevant conditions. This higher catalytic performance, persisting over a wide temperature range (250–320 °C), demonstrates the potential of the system for developing a practically relevant technology.


  • Open Access

    Recent Mechanistic Understanding of Fischer-Tropsch Synthesis on Fe-Carbide

    by Jiachun Chai, Jidong Jiang, Yan Gong, Peng Wu, Annan Wang, Xuebing Zhang, Tao Wang, Xiangkun Meng, Quan Lin, Yijun Lv, et al.

    With an increase in energy consumption globally, Fischer-Tropsch (FT) synthesis is a good alternative for producing fuels and chemicals from coal, natural gas or biomass. Among them, coal to liquids has been put into production in countries that have large coal reserves. In this process, Fe-based catalysts are commonly used due to their earth abundance, comparatively wide operation range and ready availability to handle low H2/CO ratio from coal. Despite their extensive applications, the kinetic and mechanistic understandings of Fe carburization and FT reaction on Fe-carbides are relatively limited due to the complexity of the phase composition of the applied catalysts. This review summarizes the current state of knowledge of FT synthesis on Fe-carbide with an emphasis on the underlying mechanism. Specifically, the employment of a model catalyst, such as Raney Fe, could provide a convenient way to furnish kinetic information regarding Fe carburization and subsequent FT reaction. A major challenge for further understanding catalytic reactions occurring at the Fe-carbide surface is correlating FT activity and selectivity to a specific active site. To address this issue, the advancements of both DFT calculations and surface science techniques are highly demanded.


  • Open Access

    Recent Mechanistic Understanding of Fischer-Tropsch Synthesis on Fe-Carbide

    by Jiachun Chai, Jidong Jiang, Yan Gong, Peng Wu, Annan Wang, Xuebing Zhang, Tao Wang, Xiangkun Meng, Quan Lin, Yijun Lv, et al.

    With an increase in energy consumption globally, Fischer-Tropsch (FT) synthesis is a good alternative for producing fuels and chemicals from coal, natural gas or biomass. Among them, coal to liquids has been put into production in countries that have large coal reserves. In this process, Fe-based catalysts are commonly used due to their earth abundance, comparatively wide operation range and ready availability to handle low H2/CO ratio from coal. Despite their extensive applications, the kinetic and mechanistic understandings of Fe carburization and FT reaction on Fe-carbides are relatively limited due to the complexity of phase composition of the applied catalysts. This review summarizes the current state of knowledge of FT synthesis on Fe-carbide with an emphasis on underlying mechanism. Specifically, the employment of model catalyst, such as Raney-Fe, could provide a convenient way to furnish kinetic information regarding Fe carburization and subsequent FT reaction. A major challenge for further understanding catalytic reactions occurring at the Fe-carbide surface is correlating FT activity and selectivity to specific active site. To address this issue, the advancements of both DFT calculations and surface science techniques are highly demanded.


  • Open Access

    Influence of carbon deposits on Fe-carbide for the Fischer-Tropsch reaction

    by Jiachun Chai, Robert Pestman, Fu-Kuo Chiang, Zhuowu Men, Peng Wang, Emiel J.M. Hensen


  • Open Access

    Effects of Potassium Loading over Iron–Silica Interaction, Phase Evolution and Catalytic Behavior of Precipitated Iron-Based Catalysts for Fischer-Tropsch Synthesis

    by Hai Chang, Quan Lin, Meng Cheng, Kui Zhang, Bo Feng, Jiachun Chai, Yijun Lv, Zhuowu Men

    Potassium (K) promoter and its loading contents were shown to have remarkable effects on the Fe–O–Si interaction of precipitated Fe/Cu/K/SiO2 catalysts for low-temperature Fischer-Tropsch synthesis (FTS). With the increase in K content from 2.3% (100 g Fe based) up to 7% in the calcined precursors, Fe–O–Si interaction was weakened, as reflected by ATR/FTIR, H2-TPR and XPS investigations. XRD results confirmed that the diffraction peak intensity from (510) facet of χ-Fe5C2 phase strengthened with increasing K loading, which indicates the crystallite size of χ-Fe5C2 increased with the increase in K contents either during the syngas reduction/carburization procedure or after FTS reaction. H2-TPH results indicated that more reactive surface carbon (alpha-carbon) was obtained over the higher K samples pre-carburized by syngas. Raman spectra illustrated that a greater proportion of graphitic carbon was accumulated over the surface of spent samples with higher K loading. At the same time, ATR-FTIR, XRD and Mössbauer spectra (MES) characterization results showed that a relatively higher level of bulk phase Fayalite (Fe2SiO4) species was observed discernibly in the lowest K loading sample (2.3 K%) in this work. The catalytic evaluation results showed that the CO conversion, CO2 selectivity and O/P (C2–C4) ratio increased progressively with the increasing K loading, whereas a monotonic decline in both CO conversion and O/P (C2–C4) ratio was observed on the highest K loading sample during c.a. 280 h of TOS.


  • Open Access

    The Effect of Chlorine Modification of Precipitated Iron Catalysts on Their Fischer–Tropsch Synthesis Properties

    by Weizhen Li, Xuebing Zhang, Tao Wang, Xiaoyu Zhang, Linlin Wei, Quan Lin, Yijun Lv, Zhuowu Men

    Precipitated iron Fischer–Tropsch synthesis catalysts impregnated with chlorine were prepared and their Fischer–Tropsch synthesis performances were tested in a 1 L stirred tank reactor. The results showed that the chlorine modification had a significant influence on the Fischer–Tropsch synthesis performance of the precipitated iron catalyst. Compared with the catalyst without the chlorine modification, the catalyst containing about 0.1 wt% chlorine was deactivated by about 40% and the catalyst containing about 1 wt% chlorine was deactivated by about 65%. The textural properties, phase, reduction properties, and chlorine adsorption state of the catalysts before and after the Fischer–Tropsch synthesis were characterized. The strong interaction between chlorine and iron in the catalyst hindered the reduction and carbonization of the catalyst, which was the reason for the deactivation of the catalyst caused by the chlorine modification.


  • Open Access

    The Effect of Chlorine on the Deactivation of Precipitated Iron Fischer-Tropsch Synthesis Catalyst

    by Weizhen Li, Xuebing Zhang, Tao Wang, Xiaoyu Zhang, Linlin Wei, Quan Lin, Yijun Lv, Zhuowu Men

    Precipitated iron Fischer-Tropsch synthesis catalysts impregnated with chlorine were prepared and their Fischer-Tropsch synthesis performance was tested in a 1 L stirred tank reactor. The results showed that chlorine has great influence on the Fischer-Tropsch synthesis performance of the precipitated iron catalyst. Compared with the catalyst without chlorine, the catalyst containing about 0.1 wt% chlorine is deactivated by about 40%, and the catalyst containing about 1 wt% chlorine is deactivated by about 65%. The textural properties, phase, reduction properties, and chlorine adsorption state of the catalysts before and after Fischer-Tropsch synthesis were characterized. The strong interaction between chlorine and iron in the catalyst hinders the reduction and carbonization of the catalyst, which is the reason for the deactivation of the catalyst caused by chlorine.

  • Open Access

    Studies on pathways to carbon neutrality for indirect coal liquefaction in China

    by Chufu Li, Yonglong Li, Ming Xu, Yan Gong, Siqi Gong, Peng Wang, Pingping Li, Binqi Dong, Zhuowu Men

    The production capacity of indirect coal liquefaction (ICL) in use in China has reached a level of 8 million t/a, which corresponds to a carbon footprint of >60 million t/a. ICL is facing mountainous pressure to reduce its carbon emissions when its development is planned with carbon neutrality as a background objective. This paper studies the pathways that can lead to carbon neutrality for ICL in China, constructing four carbon-neutral pathways for ICL systems with the introduction of green hydrogen, biomass as feedstock and with CCS (carbon capture and storage), which can reduce significant carbon emissions from coal-gasification and water–gas shift processes. The carbon-neutral biomass is used to replace some coal as co-feed to gasification and combustion, leading to reduced carbon emissions as well. Calculations and economic analyses are performed on different carbon-reduction pathways using a carbon-neutral ICL system on a 1 million t/a scale as an example. The results are that the pathway of direct coal substitution with biomass is the lowest carbon-reduction route at RMB 31~125/t CO2, substitution with green hydrogen costs the highest at RMB 84~422/t CO2 and CCS costs are in the middle at RMB 96~148/t CO2. Each pathway has its pros and cons, and a combination of the three may be used for the best outcome. Furthermore, a comprehensive study and systematic summation of the critical technological processes and their underlying challenges for carbon-neutral ICL together with direction for a technological breakthrough are presented. These ICL carbon-reduction pathways presented in this paper are capable of realizing an integrated development between fossil and renewable energy sources, helping the carbon-intense coal-chemical industries to achieve their goals of carbon peak and carbon neutrality.


  • Boron adsorption and its effect on stability and CO activation of χ-Fe5C2 catalyst: An ab initio DFT study

    by Huabo Zhao, Hong Jiang, Meng Cheng, Quan Lin, Yijun Lv, Yao Xu, Junzhong Xie, Jin-Xun Liu, Zhuowu Men, Ding Ma


  • Open Access

    Development of an Iron-Based Fischer—Tropsch Catalyst with High Attrition Resistance and Stability for Industrial Application

    by Quan Lin, Meng Cheng, Kui Zhang, Weizhen Li, Peng Wu, Hai Chang, Yijun Lv, Zhuowu Men

    In order to develop an iron-based catalyst with high attrition resistance and stability for Fischer–Tropsch synthesis (FTS), a series of experiments were carried out to investigate the effects of SiO2 and its hydroxyl content and a boron promoter on the attrition resistance and catalytic behavior of spray-dried precipitated Fe/Cu/K/SiO2 catalysts. The catalysts were characterized by means of N2 physisorption, nuclear magnetic resonance (NMR), X-ray diffraction (XRD), Raman spectrum, X-ray photoelectron spectroscopy (XPS), H2-thermogravimetric analysis (H2-TGA), temperature-programmed reduction and hydrogenation (TPR and TPH), and scanning and transmission electron microscopy (SEM and TEM). The FTS performance of the catalysts was tested in a slurry-phase continuously stirred tank reactor (CSTR), while the attrition resistance study included a physical test with the standard method and a chemical attrition test under simulated reaction conditions. The results indicated that the increase in SiO2 content enhances catalysts’ attrition resistance and FTS stability, but decreases activity due to the suppression of further reduction of the catalysts. Moreover, the attrition resistance of the catalysts with the same silica content was greatly improved with an increase in hydroxyl number within silica sources, as well as the FTS activity and stability to some degree. Furthermore, the boron element was found to show remarkable promotion of FTS stability, and the promotion mechanism was discussed with regard to probable interactions between Fe and B, K and B, and SiO2 and B, etc. An optimized catalyst based on the results of this study was finalized, scaled up, and successfully applied in a megaton industrial slurry bubble FTS unit, exhibiting excellent FTS performance.