Sina Hossein Zadeh
Sina Hossein Zadeh has a total of 61 co-authors. Here are the top co-authors by number of shared publications:
- Xiaoning Qian
Department of Electrical and Computer Engineering, Texas A&M University, College Station, TX, USA
7 shared publications - Danial Khatamsaz
Department of Materials Science and Engineering Texas A&M University 77843 College Station TX USA
6 shared publications Ibrahim Karaman
6 shared publications- John Broucek
Department of Materials Science & Engineering, Texas A&M University, United States of America
5 shared publications Raymundo Arroyave
5 shared publications- Ibrahim Karaman
Department of Materials Science and Engineering, Texas A&M University, College Station, TX 77843, USA
4 shared publications
Latest Publications
- 31 October 2026
- Published by Elsevier in Acta Materialia
- Vol. 323
Bayesian-optimization-guided discovery of NiTi(Co,Cu,Pd,Hf,Zr) multi-principal element high-temperature shape memory alloys
- 31 October 2026
- Published by Elsevier in Acta Materialia
- Vol. 323
Bayesian-optimization-guided discovery of NiTi(Co,Cu,Pd,Hf,Zr) multi-principal element high-temperature shape memory alloys
- Open Access
- 7 August 2026
- Published by Elsevier in SSRN Electronic Journal
A BRAVE Alloy Design Campaign(Bayesian Risk-aware Alloy discoVery and Exploration)
In constrained alloy optimization, the compositions with the highest performance potential often reside at the boundary of phase stability---where the risk of experimental failure is also highest. This work demonstrates this principle through a risk-aware Bayesian optimization campaign on single-phase FCC high-entropy alloys in the Al--V--Cr--Mn--Fe--Co--Ni--Cu system. A learned feasibility classifier, integrated directly into the multi-objective acquisition function, probabilistically penalizes candidates likely to produce failed experiments while preserving access to high-performing boundary compositions. From approximately 27{,}000 CALPHAD-screened candidates, 48 alloys were synthesized over three closed-loop iterations targeting five objectives (yield strength, UTS/YS ratio, strain at UTS, dynamic-to-quasi-static hardness ratio, and simulated depth of penetration), exploring 0.12\% of the feasible space. Two compositional regimes emerged: a V-rich, Ni-rich high-strength regime (UTS up to ${\sim}1480$~MPa at 50\% elongation) and a Mn-containing high-ductility regime (UTS/YS up to 4.20 at $>$50\% elongation). Among feasible alloys, vanadium simultaneously drives yield strength ($r = 0.84$) and sigma-phase formation ($r = 0.54$ with infeasibility); at V = 24~at.\%, the three strongest alloys and three sigma failures share the same compositional point. Additionally, the strongest performing alloys cluster in a narrow region of compositional space (V $\geq$ 20 at.\%, Ni $\geq$ 36 at.\%), representing ${\sim}100$ of $27{,}074$ feasible candidates---a probability of $P \approx 6.5 \times 10^{-6}$ under random sampling. This dual role---consistent with the KKT prediction that constrained optima lie on active constraint boundaries---required feasibility-aware acquisition to access; hard filtering would have excluded this region entirely.- 7 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA BRAVE Alloy Design Campaign(Bayesian Risk-aware Alloy discoVery and Exploration)
In constrained alloy optimization, the compositions with the highest performance potential often reside at the boundary of phase stability---where the risk of experimental failure is also highest. This work demonstrates this principle through a risk-aware Bayesian optimization campaign on single-phase FCC high-entropy alloys in the Al--V--Cr--Mn--Fe--Co--Ni--Cu system. A learned feasibility classifier, integrated directly into the multi-objective acquisition function, probabilistically penalizes candidates likely to produce failed experiments while preserving access to high-performing boundary compositions. From approximately 27{,}000 CALPHAD-screened candidates, 48 alloys were synthesized over three closed-loop iterations targeting five objectives (yield strength, UTS/YS ratio, strain at UTS, dynamic-to-quasi-static hardness ratio, and simulated depth of penetration), exploring 0.12\% of the feasible space. Two compositional regimes emerged: a V-rich, Ni-rich high-strength regime (UTS up to ${\sim}1480$~MPa at 50\% elongation) and a Mn-containing high-ductility regime (UTS/YS up to 4.20 at $>$50\% elongation). Among feasible alloys, vanadium simultaneously drives yield strength ($r = 0.84$) and sigma-phase formation ($r = 0.54$ with infeasibility); at V = 24~at.\%, the three strongest alloys and three sigma failures share the same compositional point. Additionally, the strongest performing alloys cluster in a narrow region of compositional space (V $\geq$ 20 at.\%, Ni $\geq$ 36 at.\%), representing ${\sim}100$ of $27{,}074$ feasible candidates---a probability of $P \approx 6.5 \times 10^{-6}$ under random sampling. This dual role---consistent with the KKT prediction that constrained optima lie on active constraint boundaries---required feasibility-aware acquisition to access; hard filtering would have excluded this region entirely. - Open Access
- 17 July 2026
- Published by Elsevier in SSRN Electronic Journal
Bayesian-Optimization-Guided Discovery of NiTi(Co,Cu,Pd,Hf,Zr) Multi-Principal Element High-Temperature Shape Memory Alloys
Designing high-temperature shape memory alloys (HTSMAs) requires balancing competing objectives, including transformation temperature, thermal hysteresis, latent heat, and recoverable transformation strain. This challenge becomes particularly important in multi-principal-element alloy systems, where the compositional search space expands combinatorially and traditional experimental exploration becomes impractical. In this work, a closed-loop, multi-objective batch Bayesian optimization (BO) framework was applied to the NiTi(Co,Cu,Pd,Hf,Zr) alloy system, spanning quaternary to septenary compositions. A literature-informed design space containing 3.8 million candidate alloys was generated and screened for phase stability using thermodynamic calculations. Machine-learning models were employed to predict transformation behavior and guide alloy selection. Three iterations comprising 87 experimentally synthesized alloys were completed, with each iteration informed by new experimental data. High-throughput (HTP) differential scanning calorimetry and X-ray diffraction were used to characterize transformation temperatures, thermal hysteresis, transformation enthalpy, and lattice parameters. Theoretical transformation strains were calculated from lattice parameters using the Lattice Deformation Theory and validated through uniaxial constant-force thermal cycling of down-selected compositions. The cumulative normalized hypervolume increased from 0.544 to 0.808 over three iterations, demonstrating substantial improvement in the targeted multi-objective property space. The best-performing alloy, Ni46Ti28Hf22Co2Pd2, exhibited a maximum transformation strain of 4.18% at 300 MPa and 400 MPa and a thermal hysteresis of 16.5°C under stress-free conditions, which decreased to 13.9 °C under load. These results demonstrate that closed-loop BO, coupled with HTP experimentation and targeted validation, provides an effective strategy for navigating complex HTSMA design spaces and discovering alloys that simultaneously achieve high transformation temperatures, low hysteresis, and large recoverable strains.
- 17 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessBayesian-Optimization-Guided Discovery of NiTi(Co,Cu,Pd,Hf,Zr) Multi-Principal Element High-Temperature Shape Memory Alloys
Designing high-temperature shape memory alloys (HTSMAs) requires balancing competing objectives, including transformation temperature, thermal hysteresis, latent heat, and recoverable transformation strain. This challenge becomes particularly important in multi-principal-element alloy systems, where the compositional search space expands combinatorially and traditional experimental exploration becomes impractical. In this work, a closed-loop, multi-objective batch Bayesian optimization (BO) framework was applied to the NiTi(Co,Cu,Pd,Hf,Zr) alloy system, spanning quaternary to septenary compositions. A literature-informed design space containing 3.8 million candidate alloys was generated and screened for phase stability using thermodynamic calculations. Machine-learning models were employed to predict transformation behavior and guide alloy selection. Three iterations comprising 87 experimentally synthesized alloys were completed, with each iteration informed by new experimental data. High-throughput (HTP) differential scanning calorimetry and X-ray diffraction were used to characterize transformation temperatures, thermal hysteresis, transformation enthalpy, and lattice parameters. Theoretical transformation strains were calculated from lattice parameters using the Lattice Deformation Theory and validated through uniaxial constant-force thermal cycling of down-selected compositions. The cumulative normalized hypervolume increased from 0.544 to 0.808 over three iterations, demonstrating substantial improvement in the targeted multi-objective property space. The best-performing alloy, Ni46Ti28Hf22Co2Pd2, exhibited a maximum transformation strain of 4.18% at 300 MPa and 400 MPa and a thermal hysteresis of 16.5°C under stress-free conditions, which decreased to 13.9 °C under load. These results demonstrate that closed-loop BO, coupled with HTP experimentation and targeted validation, provides an effective strategy for navigating complex HTSMA design spaces and discovering alloys that simultaneously achieve high transformation temperatures, low hysteresis, and large recoverable strains.
- Open Access
- 17 July 2025
- Published by Elsevier in Materials Letters
- Vol. 400
Predicting hardness in refractory high-entropy alloys using machine learning
- 17 July 2025
- Published by Elsevier in Materials Letters
- Vol. 400
Open AccessPredicting hardness in refractory high-entropy alloys using machine learning
- 13 March 2025
- Published by Elsevier in Acta Materialia
- Vol. 289
A composition-based predictive model for the transformation strain of NiTi shape memory alloys
- 13 March 2025
- Published by Elsevier in Acta Materialia
- Vol. 289
A composition-based predictive model for the transformation strain of NiTi shape memory alloys
- 19 December 2024
- Published by Elsevier in Acta Materialia
- Vol. 286
Design of high-temperature NiTiCuHf shape memory alloys with minimum thermal hysteresis using Bayesian optimization
- 19 December 2024
- Published by Elsevier in Acta Materialia
- Vol. 286
Design of high-temperature NiTiCuHf shape memory alloys with minimum thermal hysteresis using Bayesian optimization
- Open Access
- 20 June 2024
- Published by Elsevier in Materials & Design
- Vol. 244
Data-driven study of composition-dependent phase compatibility in NiTi shape memory alloys
- 20 June 2024
- Published by Elsevier in Materials & Design
- Vol. 244
Open AccessData-driven study of composition-dependent phase compatibility in NiTi shape memory alloys
- Open Access
Data-driven study of composition-dependent phase compatibility in NiTi shape memory alloys
The martensitic transformation in NiTi-based Shape Memory Alloys (SMAs) provides a basis for shape memory effect and superelasticity, thereby enabling applications requiring solid-state actuation and large recoverable shape changes upon mechanical load cycling. In order to tailor the transformation to a particular application, the compositional dependence of properties in NiTi-based SMAs, such as martensitic transformation temperatures and hysteresis, has been exploited. However, the compositional design space is large and complex, and experimental studies are expensive. In this work, we develop an interpretable piecewise linear regression model that predicts the $λ_2$ parameter, a measure of compatibility between austenite and martensite phases, and an (indirect) factor that is well-correlated with martensitic transformation hysteresis, based on the chemical features derived from the alloy composition. The model is capable of predicting, for the first time, the type of martensitic transformation for a given alloy chemistry. The proposed model is validated by experimental data from the literature as well as in-house measurements. The results show that the model can effectively distinguish between $B19$ and $B19^{\prime}$ regions for any given composition in NiTi-based SMAs and accurately estimate the $λ_2$ parameter. Our analysis also reveals that the weighted average of the quotient of the first ionization energy and the Voronoi coordination number is a key compositional characteristic that correlates with the $λ_2$ parameter and thermodynamic responses, including the transformation hysteresis, martensite start temperature, and critical temperature. The work herein demonstrates the potential of data-driven methodologies for understanding and designing NiTi-based SMAs with desired transformation characteristics.Open AccessData-driven study of composition-dependent phase compatibility in NiTi shape memory alloys
The martensitic transformation in NiTi-based Shape Memory Alloys (SMAs) provides a basis for shape memory effect and superelasticity, thereby enabling applications requiring solid-state actuation and large recoverable shape changes upon mechanical load cycling. In order to tailor the transformation to a particular application, the compositional dependence of properties in NiTi-based SMAs, such as martensitic transformation temperatures and hysteresis, has been exploited. However, the compositional design space is large and complex, and experimental studies are expensive. In this work, we develop an interpretable piecewise linear regression model that predicts the $λ_2$ parameter, a measure of compatibility between austenite and martensite phases, and an (indirect) factor that is well-correlated with martensitic transformation hysteresis, based on the chemical features derived from the alloy composition. The model is capable of predicting, for the first time, the type of martensitic transformation for a given alloy chemistry. The proposed model is validated by experimental data from the literature as well as in-house measurements. The results show that the model can effectively distinguish between $B19$ and $B19^{\prime}$ regions for any given composition in NiTi-based SMAs and accurately estimate the $λ_2$ parameter. Our analysis also reveals that the weighted average of the quotient of the first ionization energy and the Voronoi coordination number is a key compositional characteristic that correlates with the $λ_2$ parameter and thermodynamic responses, including the transformation hysteresis, martensite start temperature, and critical temperature. The work herein demonstrates the potential of data-driven methodologies for understanding and designing NiTi-based SMAs with desired transformation characteristics. - Top Cited PapersOpen Access
- 13 December 2023
- Published by Springer Nature in npj Computational Materials
- Vol. 9 (1) , 1-11
A physics informed bayesian optimization approach for material design: application to NiTi shape memory alloys
The design of materials and identification of optimal processing parameters constitute a complex and challenging task, necessitating efficient utilization of available data. Bayesian Optimization (BO) has gained popularity in materials design due to its ability to work with minimal data. However, many BO-based frameworks predominantly rely on statistical information, in the form of input-output data, and assume black-box objective functions. In practice, designers often possess knowledge of the underlying physical laws governing a material system, rendering the objective function not entirely black-box, as some information is partially observable. In this study, we propose a physics-informed BO approach that integrates physics-infused kernels to effectively leverage both statistical and physical information in the decision-making process. We demonstrate that this method significantly improves decision-making efficiency and enables more data-efficient BO. The applicability of this approach is showcased through the design of NiTi shape memory alloys, where the optimal processing parameters are identified to maximize the transformation temperature.
- 13 December 2023
- Published by Springer Nature in npj Computational Materials
- Vol. 9 (1) , 1-11
Top Cited PapersOpen AccessA physics informed bayesian optimization approach for material design: application to NiTi shape memory alloys
The design of materials and identification of optimal processing parameters constitute a complex and challenging task, necessitating efficient utilization of available data. Bayesian Optimization (BO) has gained popularity in materials design due to its ability to work with minimal data. However, many BO-based frameworks predominantly rely on statistical information, in the form of input-output data, and assume black-box objective functions. In practice, designers often possess knowledge of the underlying physical laws governing a material system, rendering the objective function not entirely black-box, as some information is partially observable. In this study, we propose a physics-informed BO approach that integrates physics-infused kernels to effectively leverage both statistical and physical information in the decision-making process. We demonstrate that this method significantly improves decision-making efficiency and enables more data-efficient BO. The applicability of this approach is showcased through the design of NiTi shape memory alloys, where the optimal processing parameters are identified to maximize the transformation temperature.
- 27 April 2023
- Published by Elsevier in Computational Materials Science
- Vol. 226, 112225
An interpretable boosting-based predictive model for transformation temperatures of shape memory alloys
- 27 April 2023
- Published by Elsevier in Computational Materials Science
- Vol. 226, 112225
An interpretable boosting-based predictive model for transformation temperatures of shape memory alloys