Nina V. Nemchinova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nina V. Nemchinova has a total of 103 co-authors. Here are the top co-authors by number of shared publications:
- Andrey A. Tyutrin
Department of Non-Ferrous Metals Metallurgy, Irkutsk National Research Technical University, 664074 Irkutsk, Russia
17 shared publications A. A. Yakovleva
Irkutsk National Research Technical University
4 shared publicationsG. G. Mineev
Irkutsk National Research Technical University
4 shared publications- Aleksey A. Petrovskiy
Laboratory of Geochemistry of Ore Formation and Geochemical methods of Prospecting, A. P. Vinogradov Institute of Geochemistry of the Siberian Branch of the Russian Academy of Sciences, 664033 Irkutsk, Russia
3 shared publications - V. V. Zhmurova
Иркутский национальный исследовательский технический университет
3 shared publications - A. A. Zaitseva
Irkutsk National Research Technical University, Irkutsk, Russia
2 shared publications
Latest Publications
- 8 July 2026
- Published by National University of Science and Technology MISiS in Izvestiya Vuzov. Tsvetnaya Metallurgiya (Proceedings of Higher Schools. Nonferrous Metallurgy)
- Vol. 32 (2) , 35-45
Mathematical modeling of MHD parameters of Soderberg cells converted to prebaked anode cells
The development of the Russian aluminum industry is proceeding in several areas, among which deep modernization of aluminum production plays a key role. One of its major components is the conversion of Soderberg cells to prebaked anode cells. For this modernization, it is important to understand the state of magnetohydrodynamics of the cryolite-alumina melt as it has a significant effect on cell operation. Mathematical modeling was used to assess the feasibility of converting cells with self-baking anodes to prebaked anode cells without upgrading the busbar system, i.e., with minimal capital expenditure. The already upgraded busbar system for the S-8BM(E) Soderberg cell was used as the basis. The specialized MHD-Valdis and Blums V5.07 software packages were used to calculate the MHD operating parameters of the cell without changing the design of the cathode busbar system, anode risers, or cathode assembly. The calculation procedure involved sequentially solving the electrical problem to determine current distribution, temperature, and current densities in the sections of the cell electrical circuit. The magnetic problem was then solved to determine the magnetic field characteristics in the electrolyte melt and cathode metal, taking into account the effect of ferromagnetic masses. The Lorentz forces and their resulting effect on the static tilt of the cathode metal were then calculated, together with the metal circulation velocities, to determine the final MHD stability margin of the cell. The results show that the conversion of Soderberg cells to prebaked anode cells improves the main MHD operating parameters of the cell: the mean and mean absolute values, as well as the absolute minimum and absolute maximum values, of the vertical component of magnetic flux density decrease. In addition, the maximum cathode metal velocities decrease by 31.37 %, and the total static tilt of the cathode metal decreases by 21.25 %.
- 8 July 2026
- Published by National University of Science and Technology MISiS in Izvestiya Vuzov. Tsvetnaya Metallurgiya (Proceedings of Higher Schools. Nonferrous Metallurgy)
- Vol. 32 (2) , 35-45
Mathematical modeling of MHD parameters of Soderberg cells converted to prebaked anode cells
The development of the Russian aluminum industry is proceeding in several areas, among which deep modernization of aluminum production plays a key role. One of its major components is the conversion of Soderberg cells to prebaked anode cells. For this modernization, it is important to understand the state of magnetohydrodynamics of the cryolite-alumina melt as it has a significant effect on cell operation. Mathematical modeling was used to assess the feasibility of converting cells with self-baking anodes to prebaked anode cells without upgrading the busbar system, i.e., with minimal capital expenditure. The already upgraded busbar system for the S-8BM(E) Soderberg cell was used as the basis. The specialized MHD-Valdis and Blums V5.07 software packages were used to calculate the MHD operating parameters of the cell without changing the design of the cathode busbar system, anode risers, or cathode assembly. The calculation procedure involved sequentially solving the electrical problem to determine current distribution, temperature, and current densities in the sections of the cell electrical circuit. The magnetic problem was then solved to determine the magnetic field characteristics in the electrolyte melt and cathode metal, taking into account the effect of ferromagnetic masses. The Lorentz forces and their resulting effect on the static tilt of the cathode metal were then calculated, together with the metal circulation velocities, to determine the final MHD stability margin of the cell. The results show that the conversion of Soderberg cells to prebaked anode cells improves the main MHD operating parameters of the cell: the mean and mean absolute values, as well as the absolute minimum and absolute maximum values, of the vertical component of magnetic flux density decrease. In addition, the maximum cathode metal velocities decrease by 31.37 %, and the total static tilt of the cathode metal decreases by 21.25 %.
- Open Access
- 3 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (7) , 3487
Improving the Environmental Safety of Transport Equipment Using Biodiesel Produced from Waste Vegetable
Issues related to the environmental safety of transport vehicles, the operation of which leads to environmental pollution, continue to be highly relevant. In this work, we consider the use of biofuel mixed with diesel fuel for internal combustion engines operating at low temperatures. This approach does not reduce the efficiency of transport, while also solving the issue of organic waste recycling. In this work, we address the possibility of reducing environmental pollution using carbon-neutral blended fuels based on esters of waste cooking oil (WCO), biobutanol, and diesel fuel for transport, tractor, and other equipment powered by a diesel internal combustion engine. In terms of the rate of biofuel implementation, Russia is still lagging behind the EU, China, and Japan, largely due to, inter alia, its climatic conditions with cold and long winters. The article also provides data on the possibility of using mixed biofuels under sub-zero temperatures. The process of forming a volumetric fuel supply through the common rail injector of the D4CB engine under changes in fuel pressure and drive pulse duration was also investigated, with the corresponding regression dependencies being presented. The losses of heat supplied into the cylinder when using a blend of diesel fuel and biodiesel (with 20 wt% butanol) in comparison with diesel fuel were analytically calculated. This made it possible to identify a function for adjusting fuel supply to compensate for power losses. The lubricity of fuel blends was assessed using the HFRR method.
- 3 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (7) , 3487
Open AccessImproving the Environmental Safety of Transport Equipment Using Biodiesel Produced from Waste Vegetable
Issues related to the environmental safety of transport vehicles, the operation of which leads to environmental pollution, continue to be highly relevant. In this work, we consider the use of biofuel mixed with diesel fuel for internal combustion engines operating at low temperatures. This approach does not reduce the efficiency of transport, while also solving the issue of organic waste recycling. In this work, we address the possibility of reducing environmental pollution using carbon-neutral blended fuels based on esters of waste cooking oil (WCO), biobutanol, and diesel fuel for transport, tractor, and other equipment powered by a diesel internal combustion engine. In terms of the rate of biofuel implementation, Russia is still lagging behind the EU, China, and Japan, largely due to, inter alia, its climatic conditions with cold and long winters. The article also provides data on the possibility of using mixed biofuels under sub-zero temperatures. The process of forming a volumetric fuel supply through the common rail injector of the D4CB engine under changes in fuel pressure and drive pulse duration was also investigated, with the corresponding regression dependencies being presented. The losses of heat supplied into the cylinder when using a blend of diesel fuel and biodiesel (with 20 wt% butanol) in comparison with diesel fuel were analytically calculated. This made it possible to identify a function for adjusting fuel supply to compensate for power losses. The lubricity of fuel blends was assessed using the HFRR method.
- Open Access
- 21 September 2025
- Published by Irkutsk National Research Technical University in iPolytech Journal
- Vol. 29 (3) , 412-424
Effect of the anode paste composition of a self-baking anode on the performance of electrolytic aluminum production
The present study aims to analyze the effect of the coke type (petroleum, pitch) in the composition of an anode paste for a self-baking anode on electrolysis indicators. We collected production data from operating S-8B(M) electrolytic cells with Soderberg anodes in the period from June to October 2024, including 172 and 186 electrolytic cells installed in Series 1 in Series 2, respectively. The yield of coal foam is higher in electrolytic cells with petroleum coke anodes: 15.9 kg per 1 electrolytic cell versus 8.4 kg in cells with anodes based on pitch coke paste. During the studied period, the specific power consumption for a series of cells operating with petroleum coke paste was 15,393 kWh/t Al versus 15,341 kWh/t Al. The consumption of petroleum coke anode paste per 1 electrolytic cell is 1.82 t higher than that of cells operating on pitch coke at an anode combustion rate of 1.5 and 1.47 cm/day, respectively. The anode pin rearrangement performed during the research period revealed 285 technological viola tions, e.g., pitch leaks and gassing, for petroleum coke anodes as compared to 121 violations for another coke type. A comparative analysis of the data collected during the maintenance of electrolytic cells with Soderberg anodes proved pitch coke anodes to have the lowest carbon foam yield, specific power and anode paste consumption, and anode combustion rate. Thus, using pitch coke in the anode paste for self-baking anodes of electrolytic cells can enhance the efficiency of aluminum production.
- 21 September 2025
- Published by Irkutsk National Research Technical University in iPolytech Journal
- Vol. 29 (3) , 412-424
Open AccessEffect of the anode paste composition of a self-baking anode on the performance of electrolytic aluminum production
The present study aims to analyze the effect of the coke type (petroleum, pitch) in the composition of an anode paste for a self-baking anode on electrolysis indicators. We collected production data from operating S-8B(M) electrolytic cells with Soderberg anodes in the period from June to October 2024, including 172 and 186 electrolytic cells installed in Series 1 in Series 2, respectively. The yield of coal foam is higher in electrolytic cells with petroleum coke anodes: 15.9 kg per 1 electrolytic cell versus 8.4 kg in cells with anodes based on pitch coke paste. During the studied period, the specific power consumption for a series of cells operating with petroleum coke paste was 15,393 kWh/t Al versus 15,341 kWh/t Al. The consumption of petroleum coke anode paste per 1 electrolytic cell is 1.82 t higher than that of cells operating on pitch coke at an anode combustion rate of 1.5 and 1.47 cm/day, respectively. The anode pin rearrangement performed during the research period revealed 285 technological viola tions, e.g., pitch leaks and gassing, for petroleum coke anodes as compared to 121 violations for another coke type. A comparative analysis of the data collected during the maintenance of electrolytic cells with Soderberg anodes proved pitch coke anodes to have the lowest carbon foam yield, specific power and anode paste consumption, and anode combustion rate. Thus, using pitch coke in the anode paste for self-baking anodes of electrolytic cells can enhance the efficiency of aluminum production.
- Open Access
- 5 October 2024
- Published by Irkutsk National Research Technical University in iPolytech Journal
- Vol. 28 (3) , 562-575
Structure and dynamic viscosity of CaO–SiO2 and CaO–SiO2–B2O3 model slag systems
Correlation dependencies between the dynamic viscosity of slag and its structural parameters were studied to determine an optimal basicity of silicon smelting slag under the addition of boron oxide to eliminate slagging of the bottom of ore-smelting furnaces. Experimental studies were conducted on CaO–SiO2 and CaO– SiO2–B2O3 model slags obtained at 1600°С. Raman spectroscopic analysis was carried out using a Horiba JobinYvon HR800UV analyzer (France). Theoretical calculations of slag viscosity were performed using Urbain and Mills models. During the experiments, the key structural parameters of slag systems varied within the following limits: the experimental Raman spectrum deconvolution function from 1.41 to 2.45 and optical basicity from 0.58 to 0.68. The obtained experimental and theoretical data were related by mathematical dependencies. It was found that the dynamic viscosity of slag can be promptly determined by Raman spectroscopy on the basis of mathematical models. The dependence obtained shows that slag viscosity decreases upon an increase in the number of bridging oxygen atoms in the silicate anion structure. Notably, this decrease in slag viscosity is observed up to the value of the experimental Raman spectrum deconvolution function of ~1.55-1.60 or slag optical basicity of 0.60–0.62. When B2O3 is added, the viscosity undergoes a further decrease. In practice, for CaO–SiO2 slag systems, the use of boroncontaining flux as a liquefying agent is reasonable at CaO/SiO2 = 0.61–0.63 while maintaining the content of B2O3 in the slag at a level of 1%. The two models (classical and modified) proposed by Urbain were established to be more suitable for theoretical calculation of viscosity in CaO–SiO2 and CaO–SiO2–B2O3 systems. Mills’ model is not suitable for these purposes, since the correlation coefficients in the corresponding mathematical model are not sufficiently large. Further research in this direction is required in order to establish appropriate dependencies of slag viscosity on its structural parameters at different temperatures.
- 5 October 2024
- Published by Irkutsk National Research Technical University in iPolytech Journal
- Vol. 28 (3) , 562-575
Open AccessStructure and dynamic viscosity of CaO–SiO2 and CaO–SiO2–B2O3 model slag systems
Correlation dependencies between the dynamic viscosity of slag and its structural parameters were studied to determine an optimal basicity of silicon smelting slag under the addition of boron oxide to eliminate slagging of the bottom of ore-smelting furnaces. Experimental studies were conducted on CaO–SiO2 and CaO– SiO2–B2O3 model slags obtained at 1600°С. Raman spectroscopic analysis was carried out using a Horiba JobinYvon HR800UV analyzer (France). Theoretical calculations of slag viscosity were performed using Urbain and Mills models. During the experiments, the key structural parameters of slag systems varied within the following limits: the experimental Raman spectrum deconvolution function from 1.41 to 2.45 and optical basicity from 0.58 to 0.68. The obtained experimental and theoretical data were related by mathematical dependencies. It was found that the dynamic viscosity of slag can be promptly determined by Raman spectroscopy on the basis of mathematical models. The dependence obtained shows that slag viscosity decreases upon an increase in the number of bridging oxygen atoms in the silicate anion structure. Notably, this decrease in slag viscosity is observed up to the value of the experimental Raman spectrum deconvolution function of ~1.55-1.60 or slag optical basicity of 0.60–0.62. When B2O3 is added, the viscosity undergoes a further decrease. In practice, for CaO–SiO2 slag systems, the use of boroncontaining flux as a liquefying agent is reasonable at CaO/SiO2 = 0.61–0.63 while maintaining the content of B2O3 in the slag at a level of 1%. The two models (classical and modified) proposed by Urbain were established to be more suitable for theoretical calculation of viscosity in CaO–SiO2 and CaO–SiO2–B2O3 systems. Mills’ model is not suitable for these purposes, since the correlation coefficients in the corresponding mathematical model are not sufficiently large. Further research in this direction is required in order to establish appropriate dependencies of slag viscosity on its structural parameters at different temperatures.
- Open Access
- 17 September 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (18) , 8346
Know-How of the Effective Use of Carbon Electrodes with a through Axial Hole in the Smelting of Silicon Metal
This article describes elements of the know-how of using carbon electrodes produced using the technology of molding around a rod when smelting silicon metal. Application of our know-how will dramatically increase the competitiveness of silicon metal production. Experts’ concerns regarding the use of such electrodes were that such electrodes have a through axial hole. This significantly reduces the mechanical strength of such electrodes, which can presumably lead to problems associated with the breakage of the working side of the electrode, which is immersed in the smelting space of the furnace under the charge layer. Industrial testing of such electrodes was carried out in a 30 MVA furnace of “Tau-Ken Temir” LLP. During testing, we used an approach previously developed by our team for working with a furnace in the process of smelting silicon metal. In particular, we used an interval between top treatments of about 30 min and adhered to the principles of balanced smelting, i.e., provided a balance between the intensity of the uniform supply of the charge into the furnace and the current active electrical power. Industrial testing carried out over four weeks confirmed the stability of the operation of cheaper carbon electrodes with a through axial hole. The recovery of silicon into finished products was also improved to 88–89% and the specific energy consumption was reduced to 11.2–12.1 MWh/t of silicon metal from the initial value 14,752 MWh/t. Thus, we received additional evidence for the effectiveness of our approach in furnace operating compared to an approach based on the ultimate provision of gas and permeability of the furnace top due to excessively intense processing of the top and an uncontrolled, uneven supply of charge to the furnace.
- 17 September 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (18) , 8346
Open AccessKnow-How of the Effective Use of Carbon Electrodes with a through Axial Hole in the Smelting of Silicon Metal
This article describes elements of the know-how of using carbon electrodes produced using the technology of molding around a rod when smelting silicon metal. Application of our know-how will dramatically increase the competitiveness of silicon metal production. Experts’ concerns regarding the use of such electrodes were that such electrodes have a through axial hole. This significantly reduces the mechanical strength of such electrodes, which can presumably lead to problems associated with the breakage of the working side of the electrode, which is immersed in the smelting space of the furnace under the charge layer. Industrial testing of such electrodes was carried out in a 30 MVA furnace of “Tau-Ken Temir” LLP. During testing, we used an approach previously developed by our team for working with a furnace in the process of smelting silicon metal. In particular, we used an interval between top treatments of about 30 min and adhered to the principles of balanced smelting, i.e., provided a balance between the intensity of the uniform supply of the charge into the furnace and the current active electrical power. Industrial testing carried out over four weeks confirmed the stability of the operation of cheaper carbon electrodes with a through axial hole. The recovery of silicon into finished products was also improved to 88–89% and the specific energy consumption was reduced to 11.2–12.1 MWh/t of silicon metal from the initial value 14,752 MWh/t. Thus, we received additional evidence for the effectiveness of our approach in furnace operating compared to an approach based on the ultimate provision of gas and permeability of the furnace top due to excessively intense processing of the top and an uncontrolled, uneven supply of charge to the furnace.
- Open Access
- 30 March 2024
- Published by Irkutsk National Research Technical University in iPolytech Journal
- Vol. 28 (1) , 162-177
Analysis of the magnetohydrodynamic parameters of S-8BM (S-8B) electrolyzers in the modernization of aluminum smelters
The article aims to determine the magnetohydrodynamic parameters of an aluminum electrolyzer in order to compare different types of bus arrangements used in baths with a Soderberg anode. The electrical parameters of the electrolyzer (current distribution across blooms and anode studs) and magnetic field parameters were computed using the Blums V5.07 program (Polyfem, Russia). Data on circulation rates and skew of the metal in the electrolyzer were obtained using the MHD-Valdis program (developed by V. Boyarevich, University of Greenwich, UK). In the course of the studies, mathematical models of the C-8BM (C-8B) electrolyzer with various bus arrangements were built. Three bus arrangements were selected for testing the installation of a bridge designed to close the current distribution in the anode bus arrangement of the electrolyzer. These types of bus arrangements were realized in two variants: with and without a bridge. The obtained circulation rates and skew of the metal were used to evaluate the possibility of modernizing baths with a Soderberg anode without significant capital costs. When using the first type of bus arrangement, the best current distribution was achieved for the blooms with limits of ~757 A (for the variant without a bridge) and ~656 A (for the modernized variant with closed series), as well as for the anode studs having limits of ~1754 A and ~1609 A, respectively. With the use of the third bus arrangement variant, the current distribution was shown to slightly decrease following the installation of a bridge between the anode bus bars. The obtained results suggest that in the modernization of a C-8BM (C-8B) electrolyzer with different types of bus arrangements, current distribution across blooms and anode studs, magnetic field characteristics (By and Bz components), as well as circulation rates and skew of the metal, have no significant impact on the efficiency of this electrolyzer, which contributes to a faster transition to EcoSoderberg bath electrolysis without significant economic costs.
- 30 March 2024
- Published by Irkutsk National Research Technical University in iPolytech Journal
- Vol. 28 (1) , 162-177
Open AccessAnalysis of the magnetohydrodynamic parameters of S-8BM (S-8B) electrolyzers in the modernization of aluminum smelters
The article aims to determine the magnetohydrodynamic parameters of an aluminum electrolyzer in order to compare different types of bus arrangements used in baths with a Soderberg anode. The electrical parameters of the electrolyzer (current distribution across blooms and anode studs) and magnetic field parameters were computed using the Blums V5.07 program (Polyfem, Russia). Data on circulation rates and skew of the metal in the electrolyzer were obtained using the MHD-Valdis program (developed by V. Boyarevich, University of Greenwich, UK). In the course of the studies, mathematical models of the C-8BM (C-8B) electrolyzer with various bus arrangements were built. Three bus arrangements were selected for testing the installation of a bridge designed to close the current distribution in the anode bus arrangement of the electrolyzer. These types of bus arrangements were realized in two variants: with and without a bridge. The obtained circulation rates and skew of the metal were used to evaluate the possibility of modernizing baths with a Soderberg anode without significant capital costs. When using the first type of bus arrangement, the best current distribution was achieved for the blooms with limits of ~757 A (for the variant without a bridge) and ~656 A (for the modernized variant with closed series), as well as for the anode studs having limits of ~1754 A and ~1609 A, respectively. With the use of the third bus arrangement variant, the current distribution was shown to slightly decrease following the installation of a bridge between the anode bus bars. The obtained results suggest that in the modernization of a C-8BM (C-8B) electrolyzer with different types of bus arrangements, current distribution across blooms and anode studs, magnetic field characteristics (By and Bz components), as well as circulation rates and skew of the metal, have no significant impact on the efficiency of this electrolyzer, which contributes to a faster transition to EcoSoderberg bath electrolysis without significant economic costs.
- 22 February 2024
- Published by Pleiades Publishing Ltd in Russian Journal of Non-Ferrous Metals
- Vol. 65 (1) , 59-67
Improving the Quality of Metallurgical-Grade Silicon by Acid Leaching
The aim is to conduct research in the field of hydrometallurgical refining of metallurgical silicon. The object of research was metallurgical silicon after oxidative refining from AO Kremnii, part of the United Company RUSAL (Shelekhov, Irkutsk oblast, Russia). The chemical composition of the obtained samples was studied by X-ray fluorescence analysis and X-ray spectral microanalysis. According to elemental analysis, metallurgical silicon contains (wt %) 0.53Al, 0.6094Fe, 0.0491Ti, 0.0628Ca, 0.0066V, 0.002Cr, 0.014Mn, 0.003Cu, 0.010P, 0.007Ba, 0.007Ni, 0.002Zn. It is shown that intermetallic compounds of the following composition were recorded in the studied samples: AlFeSi2 (with an admixture of Ca), FeSi2 (with an admixture of Al), FeSi2Ti (with an admixture of Zr). To reduce the content of impurities in silicon, we selected the following acids as solvents: 10% H2SO4, HCl, and HNO3, as well as 4% HF in various ratios. To study the possibility of reactions of interaction of intermetallic compounds with selected solvents, the values of the Gibbs energy change, which had negative values, were calculated. Experimental leaching of impurities was conducted on silicon samples with particle sizes of –200 μm under constant stirring using a magnetic stirrer. The process parameters included a temperature of 60°C, a liquid-to-solid ratio of 5 : 1, and a purification duration of 60 min. It was found that using a solvent mixture of sulfuric and hydrofluoric acids in a 1 : 1 ratio achieved the highest degree of silicon purification, with an impurity removal rate of 86.85%. It is shown that when using a mixture of sulfuric and hydrochloric acids in a ratio of 1 : 3, the degree of purification of metallurgical silicon was 41.48%. In this way, solvents that enable maximum purification of silicon from impurity elements were identified.
- 22 February 2024
- Published by Pleiades Publishing Ltd in Russian Journal of Non-Ferrous Metals
- Vol. 65 (1) , 59-67
Improving the Quality of Metallurgical-Grade Silicon by Acid Leaching
The aim is to conduct research in the field of hydrometallurgical refining of metallurgical silicon. The object of research was metallurgical silicon after oxidative refining from AO Kremnii, part of the United Company RUSAL (Shelekhov, Irkutsk oblast, Russia). The chemical composition of the obtained samples was studied by X-ray fluorescence analysis and X-ray spectral microanalysis. According to elemental analysis, metallurgical silicon contains (wt %) 0.53Al, 0.6094Fe, 0.0491Ti, 0.0628Ca, 0.0066V, 0.002Cr, 0.014Mn, 0.003Cu, 0.010P, 0.007Ba, 0.007Ni, 0.002Zn. It is shown that intermetallic compounds of the following composition were recorded in the studied samples: AlFeSi2 (with an admixture of Ca), FeSi2 (with an admixture of Al), FeSi2Ti (with an admixture of Zr). To reduce the content of impurities in silicon, we selected the following acids as solvents: 10% H2SO4, HCl, and HNO3, as well as 4% HF in various ratios. To study the possibility of reactions of interaction of intermetallic compounds with selected solvents, the values of the Gibbs energy change, which had negative values, were calculated. Experimental leaching of impurities was conducted on silicon samples with particle sizes of –200 μm under constant stirring using a magnetic stirrer. The process parameters included a temperature of 60°C, a liquid-to-solid ratio of 5 : 1, and a purification duration of 60 min. It was found that using a solvent mixture of sulfuric and hydrofluoric acids in a 1 : 1 ratio achieved the highest degree of silicon purification, with an impurity removal rate of 86.85%. It is shown that when using a mixture of sulfuric and hydrochloric acids in a ratio of 1 : 3, the degree of purification of metallurgical silicon was 41.48%. In this way, solvents that enable maximum purification of silicon from impurity elements were identified.
- Open Access
- 9 January 2024
- Published by Irkutsk National Research Technical University in iPolytech Journal
- Vol. 27 (4) , 800-808
Reducing the environmental impact of aluminum production through the use of petroleum pitch
This study is aimed at developing a technology for obtaining petroleum pitch as a binder for anode mass used in the electrolytic production of aluminum from fuel oils of catalytic liquid-phase oxidative oil cracking. A review of published data on the existing methods for obtaining petroleum pitch and its properties is carried out in order to define research directions. A method for producing petroleum pitch by catalytic liquid-phase oxidative cracking of crude oil using heterogeneous metal complex catalysts is proposed. The process of petroleum pitch production is shown to undergo several stages, including homogenization of fuel oil and modifying additives; oxidative cracking of fuel oil during heating of homogenized fuel oil in a furnace; catalytic liquid-phase oxidative cracking of fuel oil with removal of distillates; rectification of light fractions; condensation of distillates; collection of light oil products; oxidation of bottom residues by air and steam; removal of oxidation distillates and petroleum pitch; and pitch pelletizing. According to the conducted comparison of the as-obtained petroleum pitch with the B-1 coal tar pitch produced by the Altai Koks JSC, the proposed material meets the technological requirements of the Krasnoyarsk Aluminum Plant of the RUSAL company. In terms of sulfur content, the proposed petroleum pitch is superior to coal tar pitch. The experiments conducted at an aluminum plant showed the petroleum pitch to contain no harmful polyaromatic hydrocarbons, in particular, carcinogenic benz(a)pyrene. Therefore, replacement of coal tar pitch with petroleum pitch could provide technological and environmental advantages for primary aluminum producers, as well as for enterprises producing various carbon materials.
- 9 January 2024
- Published by Irkutsk National Research Technical University in iPolytech Journal
- Vol. 27 (4) , 800-808
Open AccessReducing the environmental impact of aluminum production through the use of petroleum pitch
This study is aimed at developing a technology for obtaining petroleum pitch as a binder for anode mass used in the electrolytic production of aluminum from fuel oils of catalytic liquid-phase oxidative oil cracking. A review of published data on the existing methods for obtaining petroleum pitch and its properties is carried out in order to define research directions. A method for producing petroleum pitch by catalytic liquid-phase oxidative cracking of crude oil using heterogeneous metal complex catalysts is proposed. The process of petroleum pitch production is shown to undergo several stages, including homogenization of fuel oil and modifying additives; oxidative cracking of fuel oil during heating of homogenized fuel oil in a furnace; catalytic liquid-phase oxidative cracking of fuel oil with removal of distillates; rectification of light fractions; condensation of distillates; collection of light oil products; oxidation of bottom residues by air and steam; removal of oxidation distillates and petroleum pitch; and pitch pelletizing. According to the conducted comparison of the as-obtained petroleum pitch with the B-1 coal tar pitch produced by the Altai Koks JSC, the proposed material meets the technological requirements of the Krasnoyarsk Aluminum Plant of the RUSAL company. In terms of sulfur content, the proposed petroleum pitch is superior to coal tar pitch. The experiments conducted at an aluminum plant showed the petroleum pitch to contain no harmful polyaromatic hydrocarbons, in particular, carcinogenic benz(a)pyrene. Therefore, replacement of coal tar pitch with petroleum pitch could provide technological and environmental advantages for primary aluminum producers, as well as for enterprises producing various carbon materials.
- Open Access
- 5 July 2023
- Published by Irkutsk National Research Technical University in iPolytech Journal
- Vol. 27 (2) , 436-448
Improving the quality of metallurgical-grade silicon by acid leaching
This work deals with the problem of hydrometallurgical refining of metallurgical-grade silicon. Samples of metallurgical-grade silicon after oxidative refining from JSC Silicon, RUSAL (Shelekhov, Irkutsk Oblast, Russia) were subjected to X-ray fluorescence and electron microprobe analysis. The conducted elemental analysis determined their following composition, wt%: Al – 0.53, Fe – 0.6094, Ti – 0.0491, Ca – 0.0628, V – 0.0066, Cr – 0.002, Mn – 0.014, Cu – 0.003, P – 0.010, Ba – 0.007, Ni – 0.007, and Zn – 0.002. The examined samples were found to comprise the following intermetallic compounds: AlFeSi2 (with an admixture of Ca), FeSi2 (with an admixture of Al), and FeSi2Ti (with an admixture of Zr). In order to purify silicon from impurities, 10% H2SO2, HCl, HNO3, as well as 4% HF in different ratios were used as solvents. The feasibility of interactions between the intermetallic compounds and the selected solvents was assessed by calculating changes in the Gibbs energy, which had negative values. Experiments on impurity leaching were carried out using silicon samples with a particle size of –200 µm under constant stirring with a magnetic stirrer under the temperature of 600С, the liquid-to-solid ratio of 5:1, and the leaching duration of 60 min. The highest degree of silicon purification (86.85%) was achieved under leaching with a mixture of sulfuric and hydrofluoric acids in a ratio of 1:1. The use of a mixture of sulfuric and hydrochloric acids at a ratio of 1:3 resulted in the silicon purification of 41.48%. Thus, optimal solvents allowing the maximum purification of silicon from impurities were determined.
- 5 July 2023
- Published by Irkutsk National Research Technical University in iPolytech Journal
- Vol. 27 (2) , 436-448
Open AccessImproving the quality of metallurgical-grade silicon by acid leaching
This work deals with the problem of hydrometallurgical refining of metallurgical-grade silicon. Samples of metallurgical-grade silicon after oxidative refining from JSC Silicon, RUSAL (Shelekhov, Irkutsk Oblast, Russia) were subjected to X-ray fluorescence and electron microprobe analysis. The conducted elemental analysis determined their following composition, wt%: Al – 0.53, Fe – 0.6094, Ti – 0.0491, Ca – 0.0628, V – 0.0066, Cr – 0.002, Mn – 0.014, Cu – 0.003, P – 0.010, Ba – 0.007, Ni – 0.007, and Zn – 0.002. The examined samples were found to comprise the following intermetallic compounds: AlFeSi2 (with an admixture of Ca), FeSi2 (with an admixture of Al), and FeSi2Ti (with an admixture of Zr). In order to purify silicon from impurities, 10% H2SO2, HCl, HNO3, as well as 4% HF in different ratios were used as solvents. The feasibility of interactions between the intermetallic compounds and the selected solvents was assessed by calculating changes in the Gibbs energy, which had negative values. Experiments on impurity leaching were carried out using silicon samples with a particle size of –200 µm under constant stirring with a magnetic stirrer under the temperature of 600С, the liquid-to-solid ratio of 5:1, and the leaching duration of 60 min. The highest degree of silicon purification (86.85%) was achieved under leaching with a mixture of sulfuric and hydrofluoric acids in a ratio of 1:1. The use of a mixture of sulfuric and hydrochloric acids at a ratio of 1:3 resulted in the silicon purification of 41.48%. Thus, optimal solvents allowing the maximum purification of silicon from impurities were determined.
- Open Access
- 6 June 2023
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 66 (2) , 215-221
Hydrometallurgical refining of metallurgical silicon
The paper presents the results of refining silicon of metallurgical grades based on leaching of impurities with inorganic acids. Silicon samples were studied by metallographic and X-ray fluorescent methods of analysis, as well as X-ray spectral microanalysis. To improve the quality of this alloying element, we carried out experimental work on its hydrometallurgical purification with solutions of various acids (10 % H2SO4 , HCl, HNO3 , 4 % HF) and their mixtures. Values of changes in the Gibbs energy were calculated for reactions of interaction with reagents of the main impurity inclusions recorded in the studied silicon samples (FeSi2 , Fe2Si, FeSi, AlFeSi, AlFeSi2 , Al3FeSi2 , FeSi2Ti, FeAlTiSi, TiSi2 , Ca2Si). The experiments were carried out on silicon samples with a particle size of –200 μm with constant stirring by a magnetic stirrer at a temperature of 60 °С, duration 1 h and L:S = 5:1. Determination of concentration of the impurity elements in the solution after leaching was made by the atomic emission method of analysis. When hydrofluoric acid is used as a solvent, the best results are obtained for purification of iron, aluminum, and titanium (concentration in solution, mg/dm3, respectively: 2380, 831, 145). The maximum concentration of calcium in the solution (147 mg/dm3 ) was achieved by hydrochloric acid treatment of fine silicon. The most effective for transferring impurities into solution is a mixture of sulfuric and hydrofluoric acids at a ratio of 1:1. Using a mixture of H2SO4 and HCl as a solvent (at a ratio of 1:3) made it possible to achieve sufficiently high mass concentrations of impurity elements in the leaching solution. The degree of silicon purification from iron was 33.32 %, aluminum – 54.64 %, calcium – 65.77 %, titanium – 15.64 %.
- 6 June 2023
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 66 (2) , 215-221
Open AccessHydrometallurgical refining of metallurgical silicon
The paper presents the results of refining silicon of metallurgical grades based on leaching of impurities with inorganic acids. Silicon samples were studied by metallographic and X-ray fluorescent methods of analysis, as well as X-ray spectral microanalysis. To improve the quality of this alloying element, we carried out experimental work on its hydrometallurgical purification with solutions of various acids (10 % H2SO4 , HCl, HNO3 , 4 % HF) and their mixtures. Values of changes in the Gibbs energy were calculated for reactions of interaction with reagents of the main impurity inclusions recorded in the studied silicon samples (FeSi2 , Fe2Si, FeSi, AlFeSi, AlFeSi2 , Al3FeSi2 , FeSi2Ti, FeAlTiSi, TiSi2 , Ca2Si). The experiments were carried out on silicon samples with a particle size of –200 μm with constant stirring by a magnetic stirrer at a temperature of 60 °С, duration 1 h and L:S = 5:1. Determination of concentration of the impurity elements in the solution after leaching was made by the atomic emission method of analysis. When hydrofluoric acid is used as a solvent, the best results are obtained for purification of iron, aluminum, and titanium (concentration in solution, mg/dm3, respectively: 2380, 831, 145). The maximum concentration of calcium in the solution (147 mg/dm3 ) was achieved by hydrochloric acid treatment of fine silicon. The most effective for transferring impurities into solution is a mixture of sulfuric and hydrofluoric acids at a ratio of 1:1. Using a mixture of H2SO4 and HCl as a solvent (at a ratio of 1:3) made it possible to achieve sufficiently high mass concentrations of impurity elements in the leaching solution. The degree of silicon purification from iron was 33.32 %, aluminum – 54.64 %, calcium – 65.77 %, titanium – 15.64 %.