Raihan Rahmat Rabi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Raihan Rahmat Rabi has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Giorgio Monti
Sapienza University of Rome
11 shared publications- Giorgio Monti
Department of Structural and Geotechnical Engineering, Sapienza University of Rome, Rome, Italy
7 shared publications Marco Vailati
University of L’Aquila
3 shared publications- Marco Vailati
Department of Civil, Construction-Architectural and Environmental Engineering, University of L’Aquila, Piazzale Ernesto Pontieri, Monteluco, Poggio di Roio, 67100 L’Aquila, Italy
3 shared publications Vincenzo Bianco
Department of Structural Engineering and Geotechnics, Sapienza University of Rome, Rome, Italy
2 shared publications- Angelo Aloisio
University of L’Aquila
1 shared publication
Latest Publications
- Open Access
- 18 June 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (12) , 6164
Strain-Based Experimental Investigation of Load Transfer and Infill–Frame Interaction in Low-Strength RC Frames Under Cyclic Loading
Reinforced concrete (RC) infilled frames are widely used structural systems; however, seismic design provisions often idealize masonry infill as non-structural, leading to uncertainty in performance assessment. This study experimentally and numerically investigates the role of unreinforced masonry infill in RC frames, focusing on load-transfer mechanisms, strain evolution, and energy redistribution. Two 2/3-scale single-bay, single-storey RC frames (bare and fully infilled) were tested under constant axial load and quasi-static reversed cyclic lateral loading. Reinforcement strain gauges were used to capture local deformation demands, and a nonlinear macro-model was developed and validated against experimental results. Results show that the presence of masonry infill significantly increases ultimate strength, initial stiffness, and energy dissipation capacity, in comparatively more brittle post-peak cyclic behavior and accelerated stiffness degradation that leads to more abrupt post-peak degradation. Strain measurements provide clear evidence of a staged interaction mechanism: at low drift levels, the infill governs lateral resistance through diagonal compression strut action, limiting reinforcement demand in the frame; with increasing drift, progressive cracking and crushing of the infill promote a gradual transfer of forces to the RC frame, reflected by increasing reinforcement strains and stiffness degradation. At higher drift levels, the system transitions to frame-dominated behavior with localized strain concentration and shear failure at column bases or joints. These findings demonstrate that infill significantly modifies structural response and highlight the importance of incorporating strain-based mechanisms in the seismic assessment of infilled RC frames.
- 18 June 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (12) , 6164
Open AccessStrain-Based Experimental Investigation of Load Transfer and Infill–Frame Interaction in Low-Strength RC Frames Under Cyclic Loading
Reinforced concrete (RC) infilled frames are widely used structural systems; however, seismic design provisions often idealize masonry infill as non-structural, leading to uncertainty in performance assessment. This study experimentally and numerically investigates the role of unreinforced masonry infill in RC frames, focusing on load-transfer mechanisms, strain evolution, and energy redistribution. Two 2/3-scale single-bay, single-storey RC frames (bare and fully infilled) were tested under constant axial load and quasi-static reversed cyclic lateral loading. Reinforcement strain gauges were used to capture local deformation demands, and a nonlinear macro-model was developed and validated against experimental results. Results show that the presence of masonry infill significantly increases ultimate strength, initial stiffness, and energy dissipation capacity, in comparatively more brittle post-peak cyclic behavior and accelerated stiffness degradation that leads to more abrupt post-peak degradation. Strain measurements provide clear evidence of a staged interaction mechanism: at low drift levels, the infill governs lateral resistance through diagonal compression strut action, limiting reinforcement demand in the frame; with increasing drift, progressive cracking and crushing of the infill promote a gradual transfer of forces to the RC frame, reflected by increasing reinforcement strains and stiffness degradation. At higher drift levels, the system transitions to frame-dominated behavior with localized strain concentration and shear failure at column bases or joints. These findings demonstrate that infill significantly modifies structural response and highlight the importance of incorporating strain-based mechanisms in the seismic assessment of infilled RC frames.
- 17 June 2025
- Published by Springer Nature
- p. 1357-1366
Data Driven Structural Health Monitoring System: Leveraging Mechanics-Based Thresholds
- 17 June 2025
- Published by Springer Nature
- p. 1357-1366
Data Driven Structural Health Monitoring System: Leveraging Mechanics-Based Thresholds
- 28 May 2025
- Published by Springer Nature
- p. 152-166
Fragility Curves of Deformed Ground-Supported Liquid Storage Tanks
- 28 May 2025
- Published by Springer Nature
- p. 152-166
Fragility Curves of Deformed Ground-Supported Liquid Storage Tanks
- 28 May 2025
- Published by Springer Nature
- p. 215-228
Capacity Assessment of Full and Hollow-Core Rectangular Sections
- 28 May 2025
- Published by Springer Nature
- p. 215-228
Capacity Assessment of Full and Hollow-Core Rectangular Sections
- 1 May 2025
- Published by Elsevier in Reliability Engineering & System Safety
- Vol. 262
Data-driven decision support system for the safety management of railway bridge networks
- 1 May 2025
- Published by Elsevier in Reliability Engineering & System Safety
- Vol. 262
Data-driven decision support system for the safety management of railway bridge networks
- Top Cited PapersOpen Access
- 8 April 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (8) , 4074
Genetic Algorithm-Based Model Updating in a Real-Time Digital Twin for Steel Bridge Monitoring
The integration of digital twin technology with structural health monitoring (SHM) is revolutionizing the assessment and maintenance of critical infrastructure, particularly bridges. Digital twins—virtual, data-driven replicas of physical structures—enable real-time monitoring by continuously synchronizing sensor data with computational models. This study presents the development of a real-time digital twin for a three-span steel railway bridge, utilizing a high-fidelity finite element (FE) model built using OpenSeesPy v 3.5 and instrumented with 18 strategically placed accelerometers. The dynamic properties of the bridge are extracted using Stochastic Subspace Identification (SSI), enabling an accurate estimation of modal parameters. To enhance the fidelity of the digital twin, a genetic algorithm-based model-updating strategy is implemented, optimizing the steel elastic modulus to minimize discrepancies between measured and simulated frequencies and mode shapes. The results demonstrate a remarkable reduction in frequency errors (below 5%) and a significant improvement in modal shape correlation (MAC > 0.93 post-calibration), confirming the model’s ability to reflect the bridge’s true condition. This work underscores the potential of digital twins in predictive maintenance, early damage detection, and life-cycle management of bridge infrastructure, offering a scalable framework for real-time SHM in complex structural systems.
- 8 April 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (8) , 4074
Top Cited PapersOpen AccessGenetic Algorithm-Based Model Updating in a Real-Time Digital Twin for Steel Bridge Monitoring
The integration of digital twin technology with structural health monitoring (SHM) is revolutionizing the assessment and maintenance of critical infrastructure, particularly bridges. Digital twins—virtual, data-driven replicas of physical structures—enable real-time monitoring by continuously synchronizing sensor data with computational models. This study presents the development of a real-time digital twin for a three-span steel railway bridge, utilizing a high-fidelity finite element (FE) model built using OpenSeesPy v 3.5 and instrumented with 18 strategically placed accelerometers. The dynamic properties of the bridge are extracted using Stochastic Subspace Identification (SSI), enabling an accurate estimation of modal parameters. To enhance the fidelity of the digital twin, a genetic algorithm-based model-updating strategy is implemented, optimizing the steel elastic modulus to minimize discrepancies between measured and simulated frequencies and mode shapes. The results demonstrate a remarkable reduction in frequency errors (below 5%) and a significant improvement in modal shape correlation (MAC > 0.93 post-calibration), confirming the model’s ability to reflect the bridge’s true condition. This work underscores the potential of digital twins in predictive maintenance, early damage detection, and life-cycle management of bridge infrastructure, offering a scalable framework for real-time SHM in complex structural systems.
- Open Access
- 20 December 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (24) , 11948
Seismic Vulnerability Assessment of Existing Ground-Supported Liquid Storage Tanks with Deformed Shells
This study presents a novel methodology for the seismic vulnerability assessment of ground-supported liquid storage tanks, with a particular emphasis on tanks exhibiting deformed shells. The framework is built around the development of a simplified two-degree-of-freedom (2DoF) system, specifically designed to enable efficient probabilistic analysis through incremental dynamic analysis. The 2DoF model is calibrated using detailed nonlinear finite element simulations, which account for fluid–structure interaction and complex geometric effects. This approach allows for a significant reduction in computational effort while maintaining a high level of accuracy in predicting seismic fragility. A key feature of the proposed methodology is the explicit inclusion of deformed tank geometries, which are often encountered in real cases and can critically impact seismic performance. The study identifies and quantifies the effects of these deformations on various damage states, such as local buckling, overturning, and liquid overspill. Fragility curves are developed to characterize the probability of exceeding these damage states under different levels of seismic intensity. The proposed methodology is validated through a representative case study, demonstrating its ability to capture the key features of tank behavior and provide robust fragility estimates. The results highlight the potential of the 2DoF system to serve as a practical tool for seismic risk assessment, enabling engineers and researchers to evaluate tank vulnerabilities more efficiently.
- 20 December 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (24) , 11948
Open AccessSeismic Vulnerability Assessment of Existing Ground-Supported Liquid Storage Tanks with Deformed Shells
This study presents a novel methodology for the seismic vulnerability assessment of ground-supported liquid storage tanks, with a particular emphasis on tanks exhibiting deformed shells. The framework is built around the development of a simplified two-degree-of-freedom (2DoF) system, specifically designed to enable efficient probabilistic analysis through incremental dynamic analysis. The 2DoF model is calibrated using detailed nonlinear finite element simulations, which account for fluid–structure interaction and complex geometric effects. This approach allows for a significant reduction in computational effort while maintaining a high level of accuracy in predicting seismic fragility. A key feature of the proposed methodology is the explicit inclusion of deformed tank geometries, which are often encountered in real cases and can critically impact seismic performance. The study identifies and quantifies the effects of these deformations on various damage states, such as local buckling, overturning, and liquid overspill. Fragility curves are developed to characterize the probability of exceeding these damage states under different levels of seismic intensity. The proposed methodology is validated through a representative case study, demonstrating its ability to capture the key features of tank behavior and provide robust fragility estimates. The results highlight the potential of the 2DoF system to serve as a practical tool for seismic risk assessment, enabling engineers and researchers to evaluate tank vulnerabilities more efficiently.
- 22 September 2024
- Published by Springer Nature
- p. 277-287
Energy-based Design of Dissipative Bracing Systems for Seismic Retrofitting of RC Buildings
- 22 September 2024
- Published by Springer Nature
- p. 277-287
Energy-based Design of Dissipative Bracing Systems for Seismic Retrofitting of RC Buildings
- Top Cited PapersOpen Access
Effectiveness of Vibration-Based Techniques for Damage Localization and Lifetime Prediction in Structural Health Monitoring of Bridges: A Comprehensive Review
Bridges are essential to infrastructure and transportation networks, but face challenges from heavier traffic, higher speeds, and modifications like busway integration, leading to potential overloading and costly maintenance. Structural Health Monitoring (SHM) plays a crucial role in assessing bridge conditions and predicting failures to maintain structural integrity. Vibration-based condition monitoring employs non-destructive, in situ sensing and analysis of system dynamics across time, frequency, or modal domains. This method detects changes indicative of damage or deterioration, offering a proactive approach to maintenance in civil engineering. Such monitoring systems hold promise for optimizing the management and upkeep of modern infrastructure, potentially reducing operational costs. This paper aims to assist newcomers, practitioners, and researchers in navigating various methodologies for damage identification using sensor data from real structures. It offers a comprehensive review of prevalent anomaly detection approaches, spanning from traditional techniques to cutting-edge methods. Additionally, it addresses challenges inherent in Vibration-Based Damage (VBD) SHM applications, including establishing damage thresholds, corrosion detection, and sensor drift.
Top Cited PapersOpen AccessEffectiveness of Vibration-Based Techniques for Damage Localization and Lifetime Prediction in Structural Health Monitoring of Bridges: A Comprehensive Review
Bridges are essential to infrastructure and transportation networks, but face challenges from heavier traffic, higher speeds, and modifications like busway integration, leading to potential overloading and costly maintenance. Structural Health Monitoring (SHM) plays a crucial role in assessing bridge conditions and predicting failures to maintain structural integrity. Vibration-based condition monitoring employs non-destructive, in situ sensing and analysis of system dynamics across time, frequency, or modal domains. This method detects changes indicative of damage or deterioration, offering a proactive approach to maintenance in civil engineering. Such monitoring systems hold promise for optimizing the management and upkeep of modern infrastructure, potentially reducing operational costs. This paper aims to assist newcomers, practitioners, and researchers in navigating various methodologies for damage identification using sensor data from real structures. It offers a comprehensive review of prevalent anomaly detection approaches, spanning from traditional techniques to cutting-edge methods. Additionally, it addresses challenges inherent in Vibration-Based Damage (VBD) SHM applications, including establishing damage thresholds, corrosion detection, and sensor drift.