Vladimir Vasiliev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Vladimir Vasiliev has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Georgiy Yu. Sidorov
Rzhanov Institute of Semiconductor Physics SB RAS, 13, Lavrentiev Avenue, Novosibirsk 630090, Russia
2 shared publications - Vasilij Semenovich Varavin
Russian Academy of Sciences
2 shared publications Yu. G. Sidorov
Institute of Semiconductor Physics of SB RAS, pr. ak. Lavrentjeva 13, 630090 Novosibirsk, Russia
2 shared publicationsA. S. Ivkin
1 shared publication- A. V. Tsarenko
Russian Academy of Sciences
1 shared publication - A.V. Vishnyakov
Rzhanov Institute of Semiconductor Physics, Siberian Branch, Russian Academy of Sciences
1 shared publication
Latest Publications
- Open Access
- 3 October 2023
- Published by Irkutsk National Research Technical University in iPolytech Journal
- Vol. 27 (3) , 583-597
Alumina production: Historical development, issues, and solutions. Part 1
This study focuses on documenting the historical stages of aluminium and alumina production prior to the transition to a modern industry structure, involving the Hall-Héroult electrometallurgical process, and their technical significance for the contemporary metallurgical complex. It highlights the significance of these stages in the development of scientific knowledge related to alumina, aluminium, and their production technology when using chemical methods for obtaining metallic aluminium. The analysis includes aspects, such as classification, technical evaluation of the processes, and the raw material base. It is shown that the formation of scientific knowledge regarding alumina and aluminium is mainly associated with the practical need for using alum and, to some extent, clay minerals. Since the commencement of deliberate research into methods for aluminium production in its elemental state and virtually until the 1890s, aluminium was primarily produced using the metallothermal methods pioneered by Henri St. Clair Deville and his colleagues due to the high thermodynamic stability of aluminium compounds and the absence of affordable energy sources. It was found that from 1854 to 1890, the production of aluminium by chemical method was associated with the use of sodium aluminium chloride (NaCl·AlCl3), natural cryolite, or synthesised fluoride salts. Available technical reagents (aluminium sulphate, ammonia alum, and aluminium hydroxide), along with natural raw materials (cryolite, bauxite, and clay), were used as source materials in this period. The extraction and processing of bauxite were primarily associated with the production of alum and aluminium sulphate consumed by light industry. Although the demand for pure aluminium oxide was limited during the metallothermic production of aluminium, the driving force behind the advancement of modern technologies for alumina production was the demand for chemical products. This demand led to the development of technology for processing bauxite, which forms the foundation of the metallurgical complex in aluminium production using the Hall-Héroult electrometallurgical method.
- 3 October 2023
- Published by Irkutsk National Research Technical University in iPolytech Journal
- Vol. 27 (3) , 583-597
Open AccessAlumina production: Historical development, issues, and solutions. Part 1
This study focuses on documenting the historical stages of aluminium and alumina production prior to the transition to a modern industry structure, involving the Hall-Héroult electrometallurgical process, and their technical significance for the contemporary metallurgical complex. It highlights the significance of these stages in the development of scientific knowledge related to alumina, aluminium, and their production technology when using chemical methods for obtaining metallic aluminium. The analysis includes aspects, such as classification, technical evaluation of the processes, and the raw material base. It is shown that the formation of scientific knowledge regarding alumina and aluminium is mainly associated with the practical need for using alum and, to some extent, clay minerals. Since the commencement of deliberate research into methods for aluminium production in its elemental state and virtually until the 1890s, aluminium was primarily produced using the metallothermal methods pioneered by Henri St. Clair Deville and his colleagues due to the high thermodynamic stability of aluminium compounds and the absence of affordable energy sources. It was found that from 1854 to 1890, the production of aluminium by chemical method was associated with the use of sodium aluminium chloride (NaCl·AlCl3), natural cryolite, or synthesised fluoride salts. Available technical reagents (aluminium sulphate, ammonia alum, and aluminium hydroxide), along with natural raw materials (cryolite, bauxite, and clay), were used as source materials in this period. The extraction and processing of bauxite were primarily associated with the production of alum and aluminium sulphate consumed by light industry. Although the demand for pure aluminium oxide was limited during the metallothermic production of aluminium, the driving force behind the advancement of modern technologies for alumina production was the demand for chemical products. This demand led to the development of technology for processing bauxite, which forms the foundation of the metallurgical complex in aluminium production using the Hall-Héroult electrometallurgical method.
- 1 January 2022
- Published by Fund Science and Culture Support Centre in Автометрия
- Vol. 58 (3) , 41-48
DETERMINATION OF THE MODULATION TRANSFER FUNCTION OF INFRARED OBJECTIVES
Предложен метод определения частотно-контрастной характеристики (ЧКХ) инфракрасного (ИК) объектива. Излучение выходной щели монохроматора с определённой длиной волны фокусировалось с помощью исследуемого объектива в виде длинной узкой освещённой полоски на холодном металлическом экране с апертурной щелью. Применение щелевой измерительной апертуры вместо точечной для сканирования изображения источника позволило увеличить полезный сигнал и использовать в качестве источника излучения выходную щель монохроматора. Вместо одиночного ИК-детектора с малой фоточувствительной площадью использовался апертурированный матричный ИК-фотоприёмник. С помощью средне- и длинноволновых фотоприёмных матриц формата 320 × 256 на основе выращенных с применением молекулярно-лучевой эпитаксии слоёв материала кадмий-ртуть- теллур были измерены функции рассеяния линии и ЧКХ ИК-объективов средне- и длинноволнового ИК-диапазонов спектра. Дано сравнение экспериментальных результатов с дифракционной ЧКХ изученных...
- 1 January 2022
- Published by Fund Science and Culture Support Centre in Автометрия
- Vol. 58 (3) , 41-48
DETERMINATION OF THE MODULATION TRANSFER FUNCTION OF INFRARED OBJECTIVES
Предложен метод определения частотно-контрастной характеристики (ЧКХ) инфракрасного (ИК) объектива. Излучение выходной щели монохроматора с определённой длиной волны фокусировалось с помощью исследуемого объектива в виде длинной узкой освещённой полоски на холодном металлическом экране с апертурной щелью. Применение щелевой измерительной апертуры вместо точечной для сканирования изображения источника позволило увеличить полезный сигнал и использовать в качестве источника излучения выходную щель монохроматора. Вместо одиночного ИК-детектора с малой фоточувствительной площадью использовался апертурированный матричный ИК-фотоприёмник. С помощью средне- и длинноволновых фотоприёмных матриц формата 320 × 256 на основе выращенных с применением молекулярно-лучевой эпитаксии слоёв материала кадмий-ртуть- теллур были измерены функции рассеяния линии и ЧКХ ИК-объективов средне- и длинноволнового ИК-диапазонов спектра. Дано сравнение экспериментальных результатов с дифракционной ЧКХ изученных...
- 1 January 2022
- Published by Metallurgizdat in Koks i khimiya
- No. 1,p. 27-36
FACTORS AFFECTING THE ADHESION OF BITUMEN WITH MINERAL MATERIALS
В работе оценено сцепление 28 образцов различных минеральных материалов с дорожным битумом. Сцепление определялось как величина площади поверхности минеральных материалов (в процентах), которая осталась покрытой битумом после кипячения образцов в воде. Установлено, что с увеличением суммарного содержания CaO, MgO, Fe2O3 и Al2O3 сцепление битума с минеральным материалом возрастает, а с увеличением концентрации SiO2, Na2O, K2O, CO2 сцепление снижается. Установлено, что битум на поверхности горных пород после кипячения в воде распределяется не хаотично, а концентрируется на определенных минеральных зернах. На поверхности гранитов и гнейсов битум концентрируется на зернах биотита, на поверхности габбро - на зернах...
- 1 January 2022
- Published by Metallurgizdat in Koks i khimiya
- No. 1,p. 27-36
FACTORS AFFECTING THE ADHESION OF BITUMEN WITH MINERAL MATERIALS
В работе оценено сцепление 28 образцов различных минеральных материалов с дорожным битумом. Сцепление определялось как величина площади поверхности минеральных материалов (в процентах), которая осталась покрытой битумом после кипячения образцов в воде. Установлено, что с увеличением суммарного содержания CaO, MgO, Fe2O3 и Al2O3 сцепление битума с минеральным материалом возрастает, а с увеличением концентрации SiO2, Na2O, K2O, CO2 сцепление снижается. Установлено, что битум на поверхности горных пород после кипячения в воде распределяется не хаотично, а концентрируется на определенных минеральных зернах. На поверхности гранитов и гнейсов битум концентрируется на зернах биотита, на поверхности габбро - на зернах...
- Open Access
- 21 December 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1124 (4) , 041026
Stabilization TiO2 anatase by F-ion doping for solar panel producing
The influence of modifying F-ion doping at various technological mode of the dopant on multi-state TiO2 is studied in details. It is so called Anatase to Rutile Transformation (ART) shown that the effect of F-doping has one the best stabilization function at these days. Basing on this, an optimal design process of F-ion modifying and an optimal doping level are discussed in details. The anatase-rutile phases were determined by X-ray method scanning with drive axis Theta-2Theta, continuous scan range 10-80 and scan speed 2 deg/min.
- 21 December 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1124 (4) , 041026
Open AccessStabilization TiO2 anatase by F-ion doping for solar panel producing
The influence of modifying F-ion doping at various technological mode of the dopant on multi-state TiO2 is studied in details. It is so called Anatase to Rutile Transformation (ART) shown that the effect of F-doping has one the best stabilization function at these days. Basing on this, an optimal design process of F-ion modifying and an optimal doping level are discussed in details. The anatase-rutile phases were determined by X-ray method scanning with drive axis Theta-2Theta, continuous scan range 10-80 and scan speed 2 deg/min.
- 30 June 2018
- Published by FSBEIHE North Caucasian Institute of Mining and Metallurgy (STU) in Sustainable Development of Mountain Territories
- Vol. 10 (2)
STUDY ON THE AMMONIA AUTOCLAVE LEACHING APPLIED TO SUBSTANDARD COPPER CONCENTRATES IN THE ZHEZKAZGAN DEPOSIT
The complexity of the mineralogical composition and the reduction of the content of valuable components in copper ores leads to the search for new alternative solutions for the production of a marketable product with the preservation of the profitability of production. Traditional pyro-metallurgical technologies, currently widespread, are not used in the construction of new metallurgical complexes, and preference is given to autoclave leaching technologies and increasing the complexity of...
- 30 June 2018
- Published by FSBEIHE North Caucasian Institute of Mining and Metallurgy (STU) in Sustainable Development of Mountain Territories
- Vol. 10 (2)
STUDY ON THE AMMONIA AUTOCLAVE LEACHING APPLIED TO SUBSTANDARD COPPER CONCENTRATES IN THE ZHEZKAZGAN DEPOSIT
The complexity of the mineralogical composition and the reduction of the content of valuable components in copper ores leads to the search for new alternative solutions for the production of a marketable product with the preservation of the profitability of production. Traditional pyro-metallurgical technologies, currently widespread, are not used in the construction of new metallurgical complexes, and preference is given to autoclave leaching technologies and increasing the complexity of...
- 13 May 2016
- Published by Wiley in physica status solidi (c)
- Vol. 13 (7-9) , 651-655
HgCdTe p+‐n structures grown by MBE on Si (013) substrates for high operating temperature SWIR detectors
Electrophysical properties of multilayered heteroepitaxial structures of Hg1‐xCdxTe with x=0.3‐0.4 grown by molecular beam epitaxy on silicon substrates are presented. The passivating effect of thin CdTe layers grown on top of the structures in single process is demonstrated. Comparison between experimental and theoretical temperature dependencies of reverse currents in n‐on‐p and p‐on‐n diodes fabricated by boron and arsenic ion implantation in vacancy‐doped p‐type and In‐doped n‐type Hg1‐xCdxTe films, respectively, are presented. The influence of p‐n junction position in double‐layer heterostructure on temperature dependencies of reverse currents is examined.
- 13 May 2016
- Published by Wiley in physica status solidi (c)
- Vol. 13 (7-9) , 651-655
HgCdTe p+‐n structures grown by MBE on Si (013) substrates for high operating temperature SWIR detectors
Electrophysical properties of multilayered heteroepitaxial structures of Hg1‐xCdxTe with x=0.3‐0.4 grown by molecular beam epitaxy on silicon substrates are presented. The passivating effect of thin CdTe layers grown on top of the structures in single process is demonstrated. Comparison between experimental and theoretical temperature dependencies of reverse currents in n‐on‐p and p‐on‐n diodes fabricated by boron and arsenic ion implantation in vacancy‐doped p‐type and In‐doped n‐type Hg1‐xCdxTe films, respectively, are presented. The influence of p‐n junction position in double‐layer heterostructure on temperature dependencies of reverse currents is examined.
- 28 September 2015
- Published by IOP Publishing in Quantum Electronics
- Vol. 45 (9) , 828-832
Frequency control of tunable lasers using a frequency-calibrated λ-meter in an experiment on preparation of Rydberg atoms in a magneto-optical trap
- 28 September 2015
- Published by IOP Publishing in Quantum Electronics
- Vol. 45 (9) , 828-832
Frequency control of tunable lasers using a frequency-calibrated λ-meter in an experiment on preparation of Rydberg atoms in a magneto-optical trap
- 1 November 2008
- Published by Pleiades Publishing Ltd in Semiconductors
- Vol. 42 (11) , 1298-1303
Properties of MIS structures based on graded-gap HgCdTe grown by molecular beam epitaxy
The effect of near-surface graded-gap layers on the electrical characteristics of MIS structures fabricated based on heteroepitaxial Hg1 − x Cd x Te films grown by molecular beam epitaxy with a two-layer SiO2/Si3N4 insulator and anodic oxide film is studied experimentally. It is shown that a larger modulation of capacitance (depth and width of the valley) is observed compared with the structures without the graded-gap layer. The field dependences of photovoltage of MIS structures with the graded-gap layers had a classical form and were characterized by a drop only in the enrichment region. For the structures without the graded-gap layer with x = 0.22, a drop in the voltage dependence of the photocurrent is observed in the region of pronounced inversion. This drop is governed by limitation of the space charge region by processes of tunneling generation via deep levels. The properties of the HgCdTe-insulator interfaces are studied.
- 1 November 2008
- Published by Pleiades Publishing Ltd in Semiconductors
- Vol. 42 (11) , 1298-1303
Properties of MIS structures based on graded-gap HgCdTe grown by molecular beam epitaxy
The effect of near-surface graded-gap layers on the electrical characteristics of MIS structures fabricated based on heteroepitaxial Hg1 − x Cd x Te films grown by molecular beam epitaxy with a two-layer SiO2/Si3N4 insulator and anodic oxide film is studied experimentally. It is shown that a larger modulation of capacitance (depth and width of the valley) is observed compared with the structures without the graded-gap layer. The field dependences of photovoltage of MIS structures with the graded-gap layers had a classical form and were characterized by a drop only in the enrichment region. For the structures without the graded-gap layer with x = 0.22, a drop in the voltage dependence of the photocurrent is observed in the region of pronounced inversion. This drop is governed by limitation of the space charge region by processes of tunneling generation via deep levels. The properties of the HgCdTe-insulator interfaces are studied.