TKTheofilos Kamperidis

Theofilos Kamperidis

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Theofilos Kamperidis has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Architecture Optimization of a Single-Chamber Air-Cathode MFC by Increasing the Number of Cathode Electrodes

    by Theofilos Kamperidis, Asimina Tremouli, Gerasimos Lyberatos

    The aim of this study was the optimization of a single-chamber microbial fuel cell (MFC) architecture, by increasing the number of cathode electrodes. An air cathode single chamber MFC with a modifiable lid and bottom was operated with 4 and 6 Gore-Tex MnO2 cathode electrodes. The anode consisted of graphite granules. It was found that the increase from 4 (total cathodic surface area of 160 cm2) to 6 (total cathodic surface area of 240 cm2) electrodes resulted in an increase of the maximum current and the maximum power output of the cell by approximately 72% and 129%, respectively. Additionally, by increasing the cathodic surface area the internal resistance (Rint) of the unit decreased by approximately 19%. The organic removal from the substrate was not affected by the addition of the new electrodes while it was high across all cases studied (chemical oxygen demand (COD) removal > 89%). The average coulombic efficiency (CE) during the 4-electrode operation was 14.3%, while the corresponding efficiency for 6-electrode operation was 18.5%.


  • Open Access

    Performance Comparison of Different Cathode Strategies on Air-Cathode Microbial Fuel Cells: Coal Fly Ash as a Cathode Catalyst

    by Asimina Tremouli, Pavlos K. Pandis, Theofilos Kamperidis, Christos Argirusis, Vassilis N. Stathopoulos, Gerasimos Lyberatos

    The effect of different cathode strategies (mullite/MnO2, Plexiglas/Gore-Tex/MnO2, mullite/coal fly ash, mullite/biochar, mullite/activated carbon) on the performance of air-cathode microbial fuel cells (MFCs) was investigated. The highest maximum power output was observed using MnO2 catalyst pasted on Gore-Tex cloth (7.7 mW/m3), yet the highest coulombic efficiencies (CEs) were achieved using MnO2 (CE 23.5 ± 2.7%) and coal fly ash (CE 20 ± 3.3%) pasted on ceramic. The results showed that the utilization of coal fly ash and biochar as catalysts in MFC technology can be a sustainable and cost-effective solution.


  • Open Access

    Comparative Study of Different Production Methods of Activated Carbon Cathodic Electrodes in Single Chamber MFC Treating Municipal Landfill Leachate

    by Pavlos K. Pandis, Theofilos Kamperidis, Konstantinos Bariamis, Ilias Vlachos, Christos Argirusis, Vassilis N. Stathopoulos, Gerasimos Lyberatos, Asimina Tremouli

    The treatment of real waste extracts with simultaneous energy production is currently under research. One method of addressing this dual task is using biochemical reactors named microbial fuel cells (MFCs). MFCs consist of a bioanode and a cathode where the oxygen reduction reaction (ORR) occurs. Cathodes are currently under optimization regarding the nature of their support, their catalytic efficiency and their configurations. In this work, we present facile preparation methods for the production of activated carbon ceramic-supported cathodic electrodes produced with three different techniques (wash-coat, brush-coat, and ultrasound-assisted deposition/infiltration). The produced cathodic electrodes were tested in a single-chamber MFC, filled with the concentrated liquid residue, after the reverse osmosis (RO-CLR) treatment of leachate from a municipal waste landfill, in order to exploit their electrochemical potential for simultaneous waste treatment and energy production. The electrode produced utilizing 20 kHz ultrasounds proved to be more effective in terms of energy harvesting (10.7 mW/g·L of leachate) and wastewater treatment (COD removal 85%). Internal resistances of the ultrasound-produced electrodes are lower, as compared to the other two methods, opening new exploitation pathways in the use of ultrasound as a means in producing electrodes for microbial fuel cells.


  • Open Access

    Effect of Food Waste Condensate Concentration on the Performance of Microbial Fuel Cells with Different Cathode Assemblies

    by Theofilos Kamperidis, Pavlos K. Pandis, Christos Argirusis, Gerasimos Lyberatos, Asimina Tremouli

    The aim of this study is to examine the effect of food waste condensate concentration (400–4000 mg COD/L) on the performance of two microbial fuel cells (MFCs). Food waste condensate is produced after condensing the vapors that result from drying and shredding of household food waste (HFW). Two identical single-chamber MFCs were constructed with different cathodic assemblies based on GoreTex cloth (Cell 1) and mullite (Cell 2) materials. Linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS) measurements were carried out to measure the maximum power output and the internal resistances of the cells. High COD removal efficiencies (>86%) were observed in all cases. Both cells performed better at low initial condensate concentrations (400–600 mg COD/L). Cell 1 achieved maximum electricity yield (1.51 mJ/g COD/L) at 500 mg COD/L and maximum coulombic efficiency (6.9%) at 400 mg COD/L. Cell 2 achieved maximum coulombic efficiency (51%) as well as maximum electricity yield (25.9 mJ/g COD/L) at 400 mg COD/L. Maximum power was observed at 600 mg COD/L for Cell 1 (14.2 mW/m2) and Cell 2 (14.4 mW/m2). Impedance measurements revealed that the charge transfer resistance and the solution resistance increased significantly with increasing condensate concentration in both cells.


  • Open Access

    A 2D Modelling Approach for Predicting the Response of a Two-Chamber Microbial Fuel Cell to Substrate Concentration and Electrolyte Conductivity Changes

    by Theofilos Kamperidis, Asimina Tremouli, Antonis Peppas, Gerasimos Lyberatos

    Bioelectrochemical systems have been the focus of extensive research due to their unique advantages of converting the chemical energy stored in waste to electricity. To acquire a better understanding and optimize these systems, modelling has been employed. A 2D microbial fuel cell (MFC) model was developed using the finite element software Comsol Multiphysics® (version 5.2), simulating a two-chamber MFC operating in batch mode. By solving mass and charge balance equations along with Monod–Butler–Volmer kinetics, the operation of the MFC was simulated. The model accurately describes voltage output and substrate consumption in the MFC. The computational results were compared with experimental data, thus validating the model. The voltage output and substrate consumption originating from the model were in agreement with the experimental data for two different cases (100 Ω, 1000 Ω external resistances). A polarization curve was extracted from the model by shifting the external resistance gradually, calculating a similar maximum power (47 mW/m2) to the observed experimental one (49 mW/m2). The validated model was used to predict the MFC response to varying initial substrate concentrations (0.125–4 g COD/L) and electrolyte conductivity (0.04–100 S/m) in order to determine the optimum operating conditions.


  • Open Access

    Comparative Study of Different Operation Modes of Microbial Fuel Cells Treating Food Residue Biomass

    by Asimina Tremouli, Theofilos Kamperidis, Gerasimos Lyberatos

    Four multiple air–cathode microbial fuel cells (MFCs) were developed under the scope of using extracts from fermentable household food waste (FORBI) for the production of bioelectricity. The operation of the MFCs was assessed in batch mode, considering each cell individually. Τhe chemical oxygen demand (COD) efficiency was relatively high in all cases (>85% for all batch cycles) while the electricity yield was 20 mJ/gCOD/L of extract solution. The four units were then electrically connected as a stack, both in series and in parallel, and were operated continuously. Approximately 62% COD consumption was obtained in continuous stack operation operated in series and 67% when operated in parallel. The electricity yield of the stack was 2.6 mJ/gCOD/L of extract solution when operated continuously in series and 0.7 mJ/gCOD/L when operated continuously in parallel.