Hamid Chakir
Hamid Chakir has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Achraf Wahid
Hassan II University
6 shared publications M. Bennai
Université Hassan II
6 shared publicationsF. Salamate
Université Hassan II
5 shared publicationsI. Khay
Université Hassan II
5 shared publications- M. Ferricha-Alami
Université Hassan II
5 shared publications Hamid Ouadi
IETR UMR 6164, INSA Rennes, France
4 shared publications
Latest Publications
- Open Access
- 1 July 2027
- Published by KEAI Publishing in Unconventional Resources
- Vol. 18
Photovoltaic maximum power extraction and delivery based on adaptive PSO-neural network-fuzzy algorithms implemented using an experimental test bench
- 1 July 2027
- Published by KEAI Publishing in Unconventional Resources
- Vol. 18
Open AccessPhotovoltaic maximum power extraction and delivery based on adaptive PSO-neural network-fuzzy algorithms implemented using an experimental test bench
- 17 January 2020
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 56 (6) , 1753-1765
Development of new construction material for thermal insulation of building based on aggregate of waste paper and cement
- 17 January 2020
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 56 (6) , 1753-1765
Development of new construction material for thermal insulation of building based on aggregate of waste paper and cement
- 28 December 2019
- Published by Pleiades Publishing Ltd in Astronomy Reports
- Vol. 63 (12) , 990-997
Reheating Temperature from D-Term Cosmological Inflation Braneworld
The D-term inflation in supergravity, in the braneworld Randall Sundrum II (RSII) context, has been proposed to solve some problems related to the four-dimensional inflation model. That scenario is...
- 28 December 2019
- Published by Pleiades Publishing Ltd in Astronomy Reports
- Vol. 63 (12) , 990-997
Reheating Temperature from D-Term Cosmological Inflation Braneworld
The D-term inflation in supergravity, in the braneworld Randall Sundrum II (RSII) context, has been proposed to solve some problems related to the four-dimensional inflation model. That scenario is...
- 1 December 2019
- Published by Springer Nature
- p. 102-115
Simulation and Analyze of Global MPPT Based on Hybrid Classical-ANN with PSO Learning Approach for PV System
- 1 December 2019
- Published by Springer Nature
- p. 102-115
Simulation and Analyze of Global MPPT Based on Hybrid Classical-ANN with PSO Learning Approach for PV System
- 1 December 2019
- Published by Elsevier in Engineering Structures
- Vol. 201
Experimental prediction of wire rope damage by energy method
- 1 December 2019
- Published by Elsevier in Engineering Structures
- Vol. 201
Experimental prediction of wire rope damage by energy method
- 1 December 2019
- Published by Elsevier in Nuclear Physics A
- Vol. 992
Rotational bands studies of the 169Er nucleus
- 1 December 2019
- Published by Elsevier in Nuclear Physics A
- Vol. 992
Rotational bands studies of the 169Er nucleus
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Development of Robust, Efficient Control and State Estimation Strategy for the Photovoltaic System using Nonlinear Backstepping Controller
The purpose of this study is to develop a robust, efficient control and a state estimation strategy for the photovoltaic system connected to the resistive load through a boost converter. This work focuses on improving the performance of the standalone photovoltaic system, by using a nonlinear control algorithm. The proposed MPPT control has two objectives: (i) Constructing the optimal PV voltage reference based on a regression plane of the considered PV array, (ii) Extracting the maximum power from this PV array in the presence of various climatic conditions; namely: solar irradiance and temperature. To meet these objectives, a nonlinear controller is designed using the Backstepping technique. A formal analysis using the Lyapunov stability exhibits that the designed controller can extract the optimal PV power. Numerical simulations are performed to highlight the tracking performances compared to a conventional MPPT control (Perturb and Observe).
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Development of Robust, Efficient Control and State Estimation Strategy for the Photovoltaic System using Nonlinear Backstepping Controller
The purpose of this study is to develop a robust, efficient control and a state estimation strategy for the photovoltaic system connected to the resistive load through a boost converter. This work focuses on improving the performance of the standalone photovoltaic system, by using a nonlinear control algorithm. The proposed MPPT control has two objectives: (i) Constructing the optimal PV voltage reference based on a regression plane of the considered PV array, (ii) Extracting the maximum power from this PV array in the presence of various climatic conditions; namely: solar irradiance and temperature. To meet these objectives, a nonlinear controller is designed using the Backstepping technique. A formal analysis using the Lyapunov stability exhibits that the designed controller can extract the optimal PV power. Numerical simulations are performed to highlight the tracking performances compared to a conventional MPPT control (Perturb and Observe).
- 9 October 2019
- Published by Springer Nature in The European Physical Journal Plus
- Vol. 134 (10) , 498
Reheating from F-term inflation on brane and gravitino abundance
- 9 October 2019
- Published by Springer Nature in The European Physical Journal Plus
- Vol. 134 (10) , 498
Reheating from F-term inflation on brane and gravitino abundance
- 27 September 2019
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics A
- Vol. 34 (27)
Observational constraints on reheating in braneworld inflation
The reheating era after inflation is analyzed in the framework of the braneworld models. We study reheating by calculating the reheating temperature in a braneworld inflation for various cosmological parameters. The variation of reheating [Formula: see text]-folding number and reheating temperature were obtained and analyzed as function of a spectrum of perturbation for a polynomial potential [Formula: see text]. We have applied the slow-roll approximation in the high energy limit to constraint the parameter potentials by confronting our results to recent Planck 2018 observations. We have shown that in general the best values of the predicted reheating temperature is of the order [Formula: see text] GeV, with a brane tension [Formula: see text] GeV4. We have also shown that the polynomial potential in the case [Formula: see text] provides the best fit results with recent observational constraints.
- 27 September 2019
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics A
- Vol. 34 (27)
Observational constraints on reheating in braneworld inflation
The reheating era after inflation is analyzed in the framework of the braneworld models. We study reheating by calculating the reheating temperature in a braneworld inflation for various cosmological parameters. The variation of reheating [Formula: see text]-folding number and reheating temperature were obtained and analyzed as function of a spectrum of perturbation for a polynomial potential [Formula: see text]. We have applied the slow-roll approximation in the high energy limit to constraint the parameter potentials by confronting our results to recent Planck 2018 observations. We have shown that in general the best values of the predicted reheating temperature is of the order [Formula: see text] GeV, with a brane tension [Formula: see text] GeV4. We have also shown that the polynomial potential in the case [Formula: see text] provides the best fit results with recent observational constraints.
- 4 September 2019
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 820, 203-211
Prediction of the Lifetime of Acrylonitrile Butadiene Styrene (ABS), by Calculation of Damage by Two Methods: Damage Based on Residual Stresses and Damage by Stages Evolution
The development of polymers has not stopped growing and taking more and more emphasis in our lives. From high-performance industries to mass-market industries, polymers are ubiquitous in every aspect of our lives, from where comes the pressing need to know their properties, characteristics, and behaviors more rigorously. This work is based on a study of the mechanical characterizations of thermoplastic polymers under the effects of damage. To serve this purpose, an experimental study was carried out on thermoplastic ABS (Acrylonitrile Butadiene Styrene) specimens. At first, we worked on altered specimens to define the mechanical characteristics of our material such as the elastic limit, the stress maximum, the breaking stress and the Young's modulus. On the one hand, and on the other hand we have created geometrical defects (discontinuity) on specimens in (ABS), to have the effect of defects on the mechanical characteristics of the material, afterwards a study of damage carried out by two methods to determine the critical fraction of life. To determine the lifetime of the ABS.
- 4 September 2019
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 820, 203-211
Prediction of the Lifetime of Acrylonitrile Butadiene Styrene (ABS), by Calculation of Damage by Two Methods: Damage Based on Residual Stresses and Damage by Stages Evolution
The development of polymers has not stopped growing and taking more and more emphasis in our lives. From high-performance industries to mass-market industries, polymers are ubiquitous in every aspect of our lives, from where comes the pressing need to know their properties, characteristics, and behaviors more rigorously. This work is based on a study of the mechanical characterizations of thermoplastic polymers under the effects of damage. To serve this purpose, an experimental study was carried out on thermoplastic ABS (Acrylonitrile Butadiene Styrene) specimens. At first, we worked on altered specimens to define the mechanical characteristics of our material such as the elastic limit, the stress maximum, the breaking stress and the Young's modulus. On the one hand, and on the other hand we have created geometrical defects (discontinuity) on specimens in (ABS), to have the effect of defects on the mechanical characteristics of the material, afterwards a study of damage carried out by two methods to determine the critical fraction of life. To determine the lifetime of the ABS.