Merve Nur Sagirli
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Merve Nur Sagirli has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ali Kilic
Istanbul Technical University
2 shared publications - Ali Demir
Department of Textile Engineering, Istanbul Technical University, Istanbul, Turkey
1 shared publication Mehmet Durmus Calisir
Textile Engineering Department, TEMAG Labs, Faculty of Textile Technology and Design Istanbul Technical University Istanbul Turkey
1 shared publication- Mehmet Durmus Calisir
TEMAG Labs, Faculty of Textile Technologies and Design, Istanbul Technical University, 34437 Istanbul, Türkiye
1 shared publication Melike Gungor
TEMAG Labs, Textile Technology and Design Faculty, Istanbul Technical University, Istanbul, Turkey
1 shared publication- Melike Gungor
Faculty of Textile Technologies and Design Istanbul Technical University Istanbul Turkiye
1 shared publication
Latest Publications
- 3 August 2021
- Published by Wiley in Polymer Engineering & Science
- Vol. 61 (9) , 2311-2322
Developing centrifugal spun thermally cross‐linked gelatin based fibrous biomats for antibacterial wound dressing applications
Fibrous materials obtained from natural polymers, such as gelatin, have been used in medical applications due to their biocompatibility and biodegradability. Herein, free‐standing durable fibrous gelatin biomats with antibacterial activity were developed via a simple, low cost and fast production route, centrifugal spinning, and subsequent thermal crosslinking. After a series of preliminary experiments, droplet−/bead‐free porous biomats with fine fibers, 3.41 ± 1.8 μm in diameter, were fabricated. Subsequently, antimicrobial biomats were produced by adding AgNO3 into the production solution. X‐ray diffractometer and energy dispersive X‐ray results showed Ag NPs existing as AgCl in the biomats, which could be attributed to chemical reaction between the Ag NPs and residual Cl in the impure gelatin. Later, both the neat‐gelatin and Ag‐gelatin biomats were thermally crosslinked at 170°C to gain stability against water. Although the Ag addition reduced ultimate tensile strength by half, from 881 to 495 kPa, the crosslinked biomats were robust enough to be used for wound dressing applications. They were also found to be highly breathable, with the air permeability of 256 and 81.2 mm/s, respectively. The biomats showed antibacterial activity against Escherichia coli and Staphylococcus aureus bacteria. The results show that the free‐standing fibrous‐gelatin‐based biomats produced is applicable for wound dressing applications.
- 3 August 2021
- Published by Wiley in Polymer Engineering & Science
- Vol. 61 (9) , 2311-2322
Developing centrifugal spun thermally cross‐linked gelatin based fibrous biomats for antibacterial wound dressing applications
Fibrous materials obtained from natural polymers, such as gelatin, have been used in medical applications due to their biocompatibility and biodegradability. Herein, free‐standing durable fibrous gelatin biomats with antibacterial activity were developed via a simple, low cost and fast production route, centrifugal spinning, and subsequent thermal crosslinking. After a series of preliminary experiments, droplet−/bead‐free porous biomats with fine fibers, 3.41 ± 1.8 μm in diameter, were fabricated. Subsequently, antimicrobial biomats were produced by adding AgNO3 into the production solution. X‐ray diffractometer and energy dispersive X‐ray results showed Ag NPs existing as AgCl in the biomats, which could be attributed to chemical reaction between the Ag NPs and residual Cl in the impure gelatin. Later, both the neat‐gelatin and Ag‐gelatin biomats were thermally crosslinked at 170°C to gain stability against water. Although the Ag addition reduced ultimate tensile strength by half, from 881 to 495 kPa, the crosslinked biomats were robust enough to be used for wound dressing applications. They were also found to be highly breathable, with the air permeability of 256 and 81.2 mm/s, respectively. The biomats showed antibacterial activity against Escherichia coli and Staphylococcus aureus bacteria. The results show that the free‐standing fibrous‐gelatin‐based biomats produced is applicable for wound dressing applications.
- 21 November 2019
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 51 (5) , 821-834
Solution blown nanofibrous air filters modified with glass microparticles
High-pressure drop and lower dust holding capacity reduce the performance of nanofibrous air filters. For that reason, this study was carried out to form filters with high-quality factor and high dust holding capacity, thanks to the glass particle additives. In this study, as an approach to such modifications, fluffy nanofiber webs were produced via solution blowing. Polyamide 6 (PA6) was chosen as the base for the nanofibrous mats, where glass microparticles were embedded as an additive to reduce web solidity. The effects of glass microparticle embedding on the filtration performance and pressure drop of the mats were investigated. SEM analysis was performed to analyze nanofiber diameter and morphology. Also, the barrier properties of samples were examined by air filtration and air permeability tests. Findings showed that the addition of glass particles did not alter fiber morphology significantly. However, lowering the pressure drop resulted in higher air permeability and better filtration performance in terms of the quality factor. Glass particles embedded composite samples exhibited a higher quality factor compared to the neat PA6 sample, and the PA6 + 5%GP sample has the highest quality factor value around 0.43. The filtration efficiency of this sample was 99.97% at an expense of 187.3 Pa pressure drop. The obtained enhancement was conducted to the lower solidity of composite webs which was 36% lower for the PA6 + 5%GP sample.
- 21 November 2019
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 51 (5) , 821-834
Solution blown nanofibrous air filters modified with glass microparticles
High-pressure drop and lower dust holding capacity reduce the performance of nanofibrous air filters. For that reason, this study was carried out to form filters with high-quality factor and high dust holding capacity, thanks to the glass particle additives. In this study, as an approach to such modifications, fluffy nanofiber webs were produced via solution blowing. Polyamide 6 (PA6) was chosen as the base for the nanofibrous mats, where glass microparticles were embedded as an additive to reduce web solidity. The effects of glass microparticle embedding on the filtration performance and pressure drop of the mats were investigated. SEM analysis was performed to analyze nanofiber diameter and morphology. Also, the barrier properties of samples were examined by air filtration and air permeability tests. Findings showed that the addition of glass particles did not alter fiber morphology significantly. However, lowering the pressure drop resulted in higher air permeability and better filtration performance in terms of the quality factor. Glass particles embedded composite samples exhibited a higher quality factor compared to the neat PA6 sample, and the PA6 + 5%GP sample has the highest quality factor value around 0.43. The filtration efficiency of this sample was 99.97% at an expense of 187.3 Pa pressure drop. The obtained enhancement was conducted to the lower solidity of composite webs which was 36% lower for the PA6 + 5%GP sample.