Elie Constantin Bayiga
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Elie Constantin Bayiga has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Gilbert François Ngon Ngon
Department of Earth Science, Faculty of Science, University of Douala, Douala P.O. Box 24157, Cameroon
3 shared publications - Jacques Etame
Department of Earth Science, Faculty of Science, University of Douala, Douala P.O. Box 24157, Cameroon
3 shared publications - Dieudonné Bitom
Department of Earth Science, Faculty of Science, University of Yaounde I, Yaounde P.O. Box 812, Cameroon
2 shared publications - Emmanuel Wantou Ngueko
Department of Earth Science, Faculty of Science, University of Dschang, Dschang P.O. Box 67, Cameroon
2 shared publications - Lionelle Bitom-Mamdem
Department of Earth Sciences, Faculty of Sciences, University of Yaoundé 1, Yaoundé P.O. Box 812, Cameroon
2 shared publications - Marcel Bertrand Hagbe Ntod
Department of Earth Science, Faculty of Science, University of Dschang, Dschang P.O. Box 67, Cameroon
2 shared publications
Latest Publications
- Open Access
- 23 June 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (7) , 320
The Physico-Mechanical, Mineralogical, and Thermal Characterization of Geopolymeric Laterite Bricks Containing Polyethylene Terephthalate Bottle Powder
Compressed earth blocks (CEBs) obtained by laterite material geopolymerization have great potential as building materials; however, plastic waste recycling remains an important challenge for the 21st century. Samples of lateritic materials (LAT) from the locality of Kompina and its surroundings (Littoral-Cameroon) were collected, given the region’s association with polyethylene terephthalate powder (P). They were used to make geopolymeric laterite bricks using a phosphoric acid solution (A) concentrated at 10 mol/L, at a fixed value of 20% phosphoric acid, and values of 0, 5, 10, 15, and 20% polyethylene terephthalate (PET) powder. To assess the suitability of these formulations for construction, the CEBs were tested and their physico-mechanical and thermal characteristics determined, including water absorption rate, compressive strength (CS), thermal conductivity, and effusivity. It was revealed that water absorption decreased for the LAT1 and LAT6 formulas, at 6.73% and 5.01%, respectively, with the lowest value being recorded when 10% of the PET powder was used. The water absorption increased beyond this percentage; the CS values did too, with a peak at 10% PET powder, reaching 6.92 MPa and 6.96 MPa for LAT1 and LAT6, respectively, and values decreasing beyond this point. The thermal conductivity and effusivity decreased, with the lowest values at 20% of the PET powder being 0.289 W·m−1·K−1 and 1078.46 J·K−1·m−2·s−1/2, and 0.289 W·m−1·K−1 and 1078.2 J·K−1·m−2·s−1/2 for LAT1 and LAT6, respectively. Based on the results obtained, we conclude that the formulation LAT-P10A20 is the most recommendable.
- 23 June 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (7) , 320
Open AccessThe Physico-Mechanical, Mineralogical, and Thermal Characterization of Geopolymeric Laterite Bricks Containing Polyethylene Terephthalate Bottle Powder
Compressed earth blocks (CEBs) obtained by laterite material geopolymerization have great potential as building materials; however, plastic waste recycling remains an important challenge for the 21st century. Samples of lateritic materials (LAT) from the locality of Kompina and its surroundings (Littoral-Cameroon) were collected, given the region’s association with polyethylene terephthalate powder (P). They were used to make geopolymeric laterite bricks using a phosphoric acid solution (A) concentrated at 10 mol/L, at a fixed value of 20% phosphoric acid, and values of 0, 5, 10, 15, and 20% polyethylene terephthalate (PET) powder. To assess the suitability of these formulations for construction, the CEBs were tested and their physico-mechanical and thermal characteristics determined, including water absorption rate, compressive strength (CS), thermal conductivity, and effusivity. It was revealed that water absorption decreased for the LAT1 and LAT6 formulas, at 6.73% and 5.01%, respectively, with the lowest value being recorded when 10% of the PET powder was used. The water absorption increased beyond this percentage; the CS values did too, with a peak at 10% PET powder, reaching 6.92 MPa and 6.96 MPa for LAT1 and LAT6, respectively, and values decreasing beyond this point. The thermal conductivity and effusivity decreased, with the lowest values at 20% of the PET powder being 0.289 W·m−1·K−1 and 1078.46 J·K−1·m−2·s−1/2, and 0.289 W·m−1·K−1 and 1078.2 J·K−1·m−2·s−1/2 for LAT1 and LAT6, respectively. Based on the results obtained, we conclude that the formulation LAT-P10A20 is the most recommendable.
- Open Access
- 1 April 2025
- Published by MDPI AG in Preprints.org
Physico-Mechanical, Mineralogical and Thermal Characterization of Geopolymeric Laterite Bricks, Associated with the Powder of Polyethylene Terephtalate Bottles
Compressed earth blocks (CEBs) obtained by geopolymerization of laterite materials have great potential as building materials, on the other hand recycling plastic waste is an important battle that human being faces in the 21st century. Samples of lateritic materials from the locality of Kompina and its surroundings (Littoral-Cameroon), associated with polyethylene terephthalate powder were used to make geopolymeric laterite bricks, with a phosphoric acid solution concentrated at 10 mol/L. A fixed value of 20% of phosphoric acid, and values of 0, 5, 10, 15 and 20% of PET powder were used. CEBs were tested, their physico-mechanical and thermal characteristics were determined ; this includes water absorption rate, bulk density, compressive strength (CS), thermal conductivity and effusivity. It emerged that, the CS values increase (2.02 to 6.92 MPa for formulas of LAT1 and from 1.94 to 6.96 MPa for formulas of LAT6) as the incorporation of the PET powder increases up to 10%, and decrease beyond ; water absorption decreases (8.21 to 6.73% for LAT1 and 7.14% to 5.01% for LAT6) up to 10% and increases beyond ; thermal conductivity and effusivity decrease (0.913 to 0.289 W.m-1.K-1 and 1962.37 to 1078.46 J.K-1.m-2.s-1/2 for LAT1, 0.911 to 0.289 W.m-1.K-1 and 1961.9 to 1078.2 J.K-1.m-2.s-1/2 for LAT6). Conclusively, the formulation LAT+10%P+20%A is recommendable.
- 1 April 2025
- Published by MDPI AG in Preprints.org
Open AccessPhysico-Mechanical, Mineralogical and Thermal Characterization of Geopolymeric Laterite Bricks, Associated with the Powder of Polyethylene Terephtalate Bottles
Compressed earth blocks (CEBs) obtained by geopolymerization of laterite materials have great potential as building materials, on the other hand recycling plastic waste is an important battle that human being faces in the 21st century. Samples of lateritic materials from the locality of Kompina and its surroundings (Littoral-Cameroon), associated with polyethylene terephthalate powder were used to make geopolymeric laterite bricks, with a phosphoric acid solution concentrated at 10 mol/L. A fixed value of 20% of phosphoric acid, and values of 0, 5, 10, 15 and 20% of PET powder were used. CEBs were tested, their physico-mechanical and thermal characteristics were determined ; this includes water absorption rate, bulk density, compressive strength (CS), thermal conductivity and effusivity. It emerged that, the CS values increase (2.02 to 6.92 MPa for formulas of LAT1 and from 1.94 to 6.96 MPa for formulas of LAT6) as the incorporation of the PET powder increases up to 10%, and decrease beyond ; water absorption decreases (8.21 to 6.73% for LAT1 and 7.14% to 5.01% for LAT6) up to 10% and increases beyond ; thermal conductivity and effusivity decrease (0.913 to 0.289 W.m-1.K-1 and 1962.37 to 1078.46 J.K-1.m-2.s-1/2 for LAT1, 0.911 to 0.289 W.m-1.K-1 and 1961.9 to 1078.2 J.K-1.m-2.s-1/2 for LAT6). Conclusively, the formulation LAT+10%P+20%A is recommendable.
- Open Access
- 12 September 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (18) , 9143
Mineralogical, Geochemical Characterization and Physicochemical Properties of Kaolinitic Clays of the Eastern Part of the Douala Sub-Basin, Cameroon, Central Africa
The sedimentary clays of the Douala sub-basin (Cameroon) were studied to determine their mineralogical composition and physicochemical properties to boost their potential suitability as materials for traditional ceramics and eventually modern ceramics. These clayey materials are not widely used locally as building materials and little data are available on these materials in the field of ceramics and they are relatively unknown. Three profiles from 3.9 to 7.4 m thickness were studied on the field in order to determine their mineralogical (X-ray diffraction, infrared), chemical (X-ray fluorescence) and physicochemical (particle size, Atterberg limits, organic matter, cation exchange capacity and hydrogen potential) properties. Globally, ten (10) clay samples were analyzed to highlight the nature and technological properties of these clays. Mineralogically, kaolinite (48.3–69.2 wt.%) and quartz (20.5–41.2 wt.%) were the most abundant minerals in these raw clay materials. They were associated with a very small or moderate quantity of illite, hematite, goethite, feldspar, gibbsite and micas. Geochemically, the clayey materials had high silica (SiO2, 22.21–58.03%) and alumina (Al2O3, 12.84–22.94%) contents, with a significant amount of iron oxides (Fe2O3, 1.07–17.92%). Other oxides (K2O, MgO, TiO2, Na2O, MnO, CaO and P2O5) were in a relatively lower proportion. A high level of alumina content explains the kaolinitic nature of these clayey materials. The results of the granulometric analysis of the clayey materials showed the following distribution: clay (26–99%) followed by silt (1–70%) and sand (0–4%). This corresponds to silty clay soils according to the Belgian textural classification diagram, with high plastic index (63.9%) characteristics. The studied clay materials are good candidates for the production of ceramics and terracotta building. This study is therefore important for any application of this type of clay in various industrial fields.
- 12 September 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (18) , 9143
Open AccessMineralogical, Geochemical Characterization and Physicochemical Properties of Kaolinitic Clays of the Eastern Part of the Douala Sub-Basin, Cameroon, Central Africa
The sedimentary clays of the Douala sub-basin (Cameroon) were studied to determine their mineralogical composition and physicochemical properties to boost their potential suitability as materials for traditional ceramics and eventually modern ceramics. These clayey materials are not widely used locally as building materials and little data are available on these materials in the field of ceramics and they are relatively unknown. Three profiles from 3.9 to 7.4 m thickness were studied on the field in order to determine their mineralogical (X-ray diffraction, infrared), chemical (X-ray fluorescence) and physicochemical (particle size, Atterberg limits, organic matter, cation exchange capacity and hydrogen potential) properties. Globally, ten (10) clay samples were analyzed to highlight the nature and technological properties of these clays. Mineralogically, kaolinite (48.3–69.2 wt.%) and quartz (20.5–41.2 wt.%) were the most abundant minerals in these raw clay materials. They were associated with a very small or moderate quantity of illite, hematite, goethite, feldspar, gibbsite and micas. Geochemically, the clayey materials had high silica (SiO2, 22.21–58.03%) and alumina (Al2O3, 12.84–22.94%) contents, with a significant amount of iron oxides (Fe2O3, 1.07–17.92%). Other oxides (K2O, MgO, TiO2, Na2O, MnO, CaO and P2O5) were in a relatively lower proportion. A high level of alumina content explains the kaolinitic nature of these clayey materials. The results of the granulometric analysis of the clayey materials showed the following distribution: clay (26–99%) followed by silt (1–70%) and sand (0–4%). This corresponds to silty clay soils according to the Belgian textural classification diagram, with high plastic index (63.9%) characteristics. The studied clay materials are good candidates for the production of ceramics and terracotta building. This study is therefore important for any application of this type of clay in various industrial fields.
- Open Access
- 1 July 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (13) , 6118
Characteristics of Kaolinitic Raw Materials from the Lokoundje River (Kribi, Cameroon) for Ceramic Applications
Eight kaolinitic materials from the Lokoundje River at Kribi were sampled and investigated for their physical, chemical, mineralogical and thermal characteristics in order to evaluate their potential suitability as raw materials in ceramics. The Lokoundje kaolinitic materials are clayey to silty clayey and are predominantly composed of kaolinite and quartz. The alkali (Na2O + K2O) content ranges between 1 and 2.5 wt.%; these low values do not favor vitrification of the ceramics but may be improved through flux amendment. The presence of goethite in some samples limits their utilization in white ceramics. The minerals content, color, metallic sound, cohesion, linear shrinkage, flexural strength, bulk density, water absorption and microstructure were determined. The XRD data reveal that kaolinite and goethite were transformed, respectively, into mullite and hematite. The colors of the fired products are characteristic of their mineral assemblage. The metallic sound is indicative of low vitrification which is confirmed by the presence of cracks due to low flux contents. The cohesion is good to very good, due to the abundance of kaolinite. The physicomechanical properties increase with temperature as well as densification. The geochemical data show that the Lokoundje alluvial clays are suitable for the manufacture of white stoneware tiles.
- 1 July 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (13) , 6118
Open AccessCharacteristics of Kaolinitic Raw Materials from the Lokoundje River (Kribi, Cameroon) for Ceramic Applications
Eight kaolinitic materials from the Lokoundje River at Kribi were sampled and investigated for their physical, chemical, mineralogical and thermal characteristics in order to evaluate their potential suitability as raw materials in ceramics. The Lokoundje kaolinitic materials are clayey to silty clayey and are predominantly composed of kaolinite and quartz. The alkali (Na2O + K2O) content ranges between 1 and 2.5 wt.%; these low values do not favor vitrification of the ceramics but may be improved through flux amendment. The presence of goethite in some samples limits their utilization in white ceramics. The minerals content, color, metallic sound, cohesion, linear shrinkage, flexural strength, bulk density, water absorption and microstructure were determined. The XRD data reveal that kaolinite and goethite were transformed, respectively, into mullite and hematite. The colors of the fired products are characteristic of their mineral assemblage. The metallic sound is indicative of low vitrification which is confirmed by the presence of cracks due to low flux contents. The cohesion is good to very good, due to the abundance of kaolinite. The physicomechanical properties increase with temperature as well as densification. The geochemical data show that the Lokoundje alluvial clays are suitable for the manufacture of white stoneware tiles.