Zane A. Roberts
Research Subjects
Zane A. Roberts has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
Steven F. Son
Purdue Univ, Sch Mech Engn, 585 Purdue Mall, W Lafayette, IN 47907 USA
5 shared publicationsI. E. Gunduz
School of Mechanical Engineering, Purdue University 1 , West Lafayette, Indiana 47907, USA
3 shared publicationsI. Emre Gunduz
3 shared publications- Jeffrey F. Rhoads
School of Mechanical Engineering, Purdue University, West Lafayette, USA
3 shared publications Kamel Fezzaa
Argonne National Laboratory
3 shared publications- Niranjan D. Parab
Argonne National Laboratory
3 shared publications
Latest Publications
- Open Access
- 8 August 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (6)
Additive manufacturing of high explosives with inert dilution for wave shaping and detonation velocity grading
The performance of a high explosive charge is highly influenced by the detonation velocity and any inherent internal structure. Additively manufactured (AM) high explosive charges allow for a precisely engineered internal structure and the selective placement of discrete or graded volumes of a tailored material, which are unachievable by conventional means. The dilution of a solid explosive by an inert additive for detonation velocity reduction is herein evaluated for a method of material extrusion called a direct-ink-write AM, where an 1,3,5,7-tetranitro-1,3,5,7-tetrazoctane-based ultraviolet -curable energetic-binder paste explosive was diluted by the inert density mock 5-iodo-2′-deoxyuridine for use in the manufacture of multi-material explosive charges. The explosive ink was characterized for printing by rheological and particle size measurements, and the detonation velocities for 0–40 wt. % inert diluent were found to have a continuous linear reduction in detonation velocity down to 14.3% difference. A two-component 3D plane wave explosive lens with 8.038 km/s “fast” and 7.491 km/s “slow” diluted ink in an internal cone demonstrated a reduced time of breakout at the output face from 361 to 53 ns. A linearly graded “fast–slow–fast” cylinder was successfully printed and fired, showing engineered control along the length of the charge as the detonation velocity dropped from 7.851 to 6.700 km/s and then recovered to 7.241 km/s. The extreme control over the internal composition of a high explosive charge via a dual-material extruder/mixer challenges conventional manufacturing approaches and opens new avenues for engineered detonation wavefronts, high explosive charge performance, and new applications.
- 8 August 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (6)
Open AccessAdditive manufacturing of high explosives with inert dilution for wave shaping and detonation velocity grading
The performance of a high explosive charge is highly influenced by the detonation velocity and any inherent internal structure. Additively manufactured (AM) high explosive charges allow for a precisely engineered internal structure and the selective placement of discrete or graded volumes of a tailored material, which are unachievable by conventional means. The dilution of a solid explosive by an inert additive for detonation velocity reduction is herein evaluated for a method of material extrusion called a direct-ink-write AM, where an 1,3,5,7-tetranitro-1,3,5,7-tetrazoctane-based ultraviolet -curable energetic-binder paste explosive was diluted by the inert density mock 5-iodo-2′-deoxyuridine for use in the manufacture of multi-material explosive charges. The explosive ink was characterized for printing by rheological and particle size measurements, and the detonation velocities for 0–40 wt. % inert diluent were found to have a continuous linear reduction in detonation velocity down to 14.3% difference. A two-component 3D plane wave explosive lens with 8.038 km/s “fast” and 7.491 km/s “slow” diluted ink in an internal cone demonstrated a reduced time of breakout at the output face from 361 to 53 ns. A linearly graded “fast–slow–fast” cylinder was successfully printed and fired, showing engineered control along the length of the charge as the detonation velocity dropped from 7.851 to 6.700 km/s and then recovered to 7.241 km/s. The extreme control over the internal composition of a high explosive charge via a dual-material extruder/mixer challenges conventional manufacturing approaches and opens new avenues for engineered detonation wavefronts, high explosive charge performance, and new applications.
- 1 January 2022
- Published by Elsevier in Combustion and Flame
- Vol. 235
Direct observations of ultrasonically generated hot spots in polymer composite energetic materials
- 1 January 2022
- Published by Elsevier in Combustion and Flame
- Vol. 235
Direct observations of ultrasonically generated hot spots in polymer composite energetic materials
- 9 October 2019
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 6 (1) , 34-44
Observation of Damage During Dynamic Compression of Production and Low-Defect HMX Crystals in Sylgard® Binder Using X-Ray Phase Contrast Imaging
- 9 October 2019
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 6 (1) , 34-44
Observation of Damage During Dynamic Compression of Production and Low-Defect HMX Crystals in Sylgard® Binder Using X-Ray Phase Contrast Imaging
- 1 August 2019
- Published by Elsevier in Computational Materials Science
- Vol. 166, 170-178
The effect of the particle surface and binder properties on the response of polymer bonded explosives at low impact velocities
- 1 August 2019
- Published by Elsevier in Computational Materials Science
- Vol. 166, 170-178
The effect of the particle surface and binder properties on the response of polymer bonded explosives at low impact velocities
- 7 June 2019
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 125 (21) , 215114
Mesoscale observations of the thermal decomposition of energetic composites under ultrasonic excitation
Polymer bonded explosives (PBXs) have exhibited localized heating and, in some cases, subsequent reactions in response to ultrasonic excitation. The objectives of this work are to investigate the conditions for, and locations of, hot spot initiation of energetic crystals embedded within a polymer binder subjected to periodic mechanical excitation from a contacting transducer operating at 210.5 kHz. Crystal and binder interactions and events such as delamination, solid-solid phase change, and gas production were observed in real time via optical microscopy. We conclude that there are two main pathways of heat generation which are capable of driving an explosive to decomposition in the systems of interest: frictional heating from a delaminated and moving binder interface and viscoelastic heating in the binder near an embedded crystal. Formulations that address the vibration initiation sensitivity of PBX composites require knowledge of the key internal heat generation mechanisms. The results included here indicate that improving binder adhesion to energetic crystals or improving crystal morphology to reduce heating during cyclic loading may only address one of the available pathways of energy dissipation and that binder and crystal selection should be done concurrently. Furthermore, the results presented herein appear to indicate that rounded particles, in contrast to faceted crystals, with strong adhesion to the binder are expected to result in decreased heating rates under ultrasonic excitation.
- 7 June 2019
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 125 (21) , 215114
Mesoscale observations of the thermal decomposition of energetic composites under ultrasonic excitation
Polymer bonded explosives (PBXs) have exhibited localized heating and, in some cases, subsequent reactions in response to ultrasonic excitation. The objectives of this work are to investigate the conditions for, and locations of, hot spot initiation of energetic crystals embedded within a polymer binder subjected to periodic mechanical excitation from a contacting transducer operating at 210.5 kHz. Crystal and binder interactions and events such as delamination, solid-solid phase change, and gas production were observed in real time via optical microscopy. We conclude that there are two main pathways of heat generation which are capable of driving an explosive to decomposition in the systems of interest: frictional heating from a delaminated and moving binder interface and viscoelastic heating in the binder near an embedded crystal. Formulations that address the vibration initiation sensitivity of PBX composites require knowledge of the key internal heat generation mechanisms. The results included here indicate that improving binder adhesion to energetic crystals or improving crystal morphology to reduce heating during cyclic loading may only address one of the available pathways of energy dissipation and that binder and crystal selection should be done concurrently. Furthermore, the results presented herein appear to indicate that rounded particles, in contrast to faceted crystals, with strong adhesion to the binder are expected to result in decreased heating rates under ultrasonic excitation.
- 1 June 2019
- Published by Elsevier in Applied Materials Today
- Vol. 15, 286-294
In-situ X-ray observations of ultrasound-induced explosive decomposition
- 1 June 2019
- Published by Elsevier in Applied Materials Today
- Vol. 15, 286-294
In-situ X-ray observations of ultrasound-induced explosive decomposition
- 24 May 2019
- Published by Optica Publishing Group in Applied Optics
- Vol. 58 (16) , 4320-4325
Dynamic imaging of the temperature field within an energetic composite using phosphor thermography
An improved understanding of energy localization (“hot spots”) is needed to improve the safety and performance of explosives. We propose a technique to visualize and quantify the properties of a dynamic hot spot from within an energetic composite subjected to ultrasonic mechanical excitation. The composite is composed of an optically transparent binder and a countable number of octahydro 1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) crystals. The evolving temperature field is measured by observing the luminescence from embedded phosphor particles and subsequent application of the intensity ratio method. The spatial temperature precision is less than 2% of the measured absolute temperature in the temperature regime of interest (23°C–220°C). The temperature field is mapped from within an HMX–binder composite under periodic mechanical excitation.
- 24 May 2019
- Published by Optica Publishing Group in Applied Optics
- Vol. 58 (16) , 4320-4325
Dynamic imaging of the temperature field within an energetic composite using phosphor thermography
An improved understanding of energy localization (“hot spots”) is needed to improve the safety and performance of explosives. We propose a technique to visualize and quantify the properties of a dynamic hot spot from within an energetic composite subjected to ultrasonic mechanical excitation. The composite is composed of an optically transparent binder and a countable number of octahydro 1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) crystals. The evolving temperature field is measured by observing the luminescence from embedded phosphor particles and subsequent application of the intensity ratio method. The spatial temperature precision is less than 2% of the measured absolute temperature in the temperature regime of interest (23°C–220°C). The temperature field is mapped from within an HMX–binder composite under periodic mechanical excitation.
- 22 December 2017
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 122 (24)
The effects of crystal proximity and crystal-binder adhesion on the thermal responses of ultrasonically-excited composite energetic materials
Composite energetic materials have been shown to generate heat under certain ultrasonic excitations, enough to drive rapid reactions in some cases. In an attempt to isolate the proposed heat generation mechanisms of frictional and viscoelastic heating at crystal-crystal and crystal-binder interfaces, a systematic study was conducted with cyclotetramethylene-tetranitramine crystals arranged as discrete inclusions within Sylgard 184 binder. Groups of three embedded crystals, or “triads,” were arranged in two geometries with the crystals either in contact or slightly separated. Additionally, samples with good crystal-binder adhesion as well as ones mechanically debonded using compression were considered. The samples were excited ultrasonically with a contact piezoelectric transducer, and the top surface of each sample was monitored via infrared thermography. The contacting triads showed evidence of an intense localized heat source conducting to the polymer surface above the crystal locations in contrast to the separated triads. The debonded samples of both types reached higher maximum surface temperatures, on average. The results of both two-way and nested analysis of variance indicate a statistically significant difference for both adhesion and separation distance on temperature rise. We conclude that friction between crystal contact points and a debonded, moving binder at the crystal interface (also a mode of friction) play a significant role in localized heat generation, while viscoelastic/viscoplastic heating appears comparatively minor for these specific excitation conditions. The significance of frictional heat generation over viscoelastic heating in these systems may influence future design considerations related to the selection of binder materials for composite energetic materials.
- 22 December 2017
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 122 (24)
The effects of crystal proximity and crystal-binder adhesion on the thermal responses of ultrasonically-excited composite energetic materials
Composite energetic materials have been shown to generate heat under certain ultrasonic excitations, enough to drive rapid reactions in some cases. In an attempt to isolate the proposed heat generation mechanisms of frictional and viscoelastic heating at crystal-crystal and crystal-binder interfaces, a systematic study was conducted with cyclotetramethylene-tetranitramine crystals arranged as discrete inclusions within Sylgard 184 binder. Groups of three embedded crystals, or “triads,” were arranged in two geometries with the crystals either in contact or slightly separated. Additionally, samples with good crystal-binder adhesion as well as ones mechanically debonded using compression were considered. The samples were excited ultrasonically with a contact piezoelectric transducer, and the top surface of each sample was monitored via infrared thermography. The contacting triads showed evidence of an intense localized heat source conducting to the polymer surface above the crystal locations in contrast to the separated triads. The debonded samples of both types reached higher maximum surface temperatures, on average. The results of both two-way and nested analysis of variance indicate a statistically significant difference for both adhesion and separation distance on temperature rise. We conclude that friction between crystal contact points and a debonded, moving binder at the crystal interface (also a mode of friction) play a significant role in localized heat generation, while viscoelastic/viscoplastic heating appears comparatively minor for these specific excitation conditions. The significance of frictional heat generation over viscoelastic heating in these systems may influence future design considerations related to the selection of binder materials for composite energetic materials.
- 15 November 2017
- Published by DEStech Publications
Adhesive Energy Between Sylgard and Inclusions: Experiments and Model Calibration
There are well established classical experimental and analytical studies to analyze the bonding between polymers and rigid particles. On the other hand, most numerical studies of fracture in composite materials use particle/matrix interface cohesive laws and parameters extracted from the cohesive energy at the macroscale level. Such an approach enables good results when the mechanical response is compared to macroscale experiments but in high energy composites where localization of energy dissipation by delamination and friction may lead to initiation of hot spots the particle/matrix cohesive law is of extreme importance. In this work systematic experimental and numerical studies are performed to establish a cohesive law of the composite interface.
- 15 November 2017
- Published by DEStech Publications
Adhesive Energy Between Sylgard and Inclusions: Experiments and Model Calibration
There are well established classical experimental and analytical studies to analyze the bonding between polymers and rigid particles. On the other hand, most numerical studies of fracture in composite materials use particle/matrix interface cohesive laws and parameters extracted from the cohesive energy at the macroscale level. Such an approach enables good results when the mechanical response is compared to macroscale experiments but in high energy composites where localization of energy dissipation by delamination and friction may lead to initiation of hot spots the particle/matrix cohesive law is of extreme importance. In this work systematic experimental and numerical studies are performed to establish a cohesive law of the composite interface.
- 26 September 2016
- Published by AIP Publishing in Applied Physics Letters
- Vol. 109 (13) , 131903
High speed X-ray phase contrast imaging of energetic composites under dynamic compression
Fracture of crystals and frictional heating are associated with the formation of “hot spots” (localized heating) in energetic composites such as polymer bonded explosives (PBXs). Traditional high speed optical imaging methods cannot be used to study the dynamic sub-surface deformation and the fracture behavior of such materials due to their opaque nature. In this study, high speed synchrotron X-ray experiments are conducted to visualize the in situ deformation and the fracture mechanisms in PBXs composed of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) crystals and hydroxyl-terminated polybutadiene binder doped with iron (III) oxide. A modified Kolsky bar apparatus was used to apply controlled dynamic compression on the PBX specimens, and a high speed synchrotron X-ray phase contrast imaging (PCI) setup was used to record the in situ deformation and failure in the specimens. The experiments show that synchrotron X-ray PCI provides a sufficient contrast between the HMX crystals and the doped binder, even at ultrafast recording rates. Under dynamic compression, most of the cracking in the crystals was observed to be due to the tensile stress generated by the diametral compression applied from the contacts between the crystals. Tensile stress driven cracking was also observed for some of the crystals due to the transverse deformation of the binder and superior bonding between the crystal and the binder. The obtained results are vital to develop improved understanding and to validate the macroscopic and mesoscopic numerical models for energetic composites so that eventually hot spot formation can be predicted.
- 26 September 2016
- Published by AIP Publishing in Applied Physics Letters
- Vol. 109 (13) , 131903
High speed X-ray phase contrast imaging of energetic composites under dynamic compression
Fracture of crystals and frictional heating are associated with the formation of “hot spots” (localized heating) in energetic composites such as polymer bonded explosives (PBXs). Traditional high speed optical imaging methods cannot be used to study the dynamic sub-surface deformation and the fracture behavior of such materials due to their opaque nature. In this study, high speed synchrotron X-ray experiments are conducted to visualize the in situ deformation and the fracture mechanisms in PBXs composed of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) crystals and hydroxyl-terminated polybutadiene binder doped with iron (III) oxide. A modified Kolsky bar apparatus was used to apply controlled dynamic compression on the PBX specimens, and a high speed synchrotron X-ray phase contrast imaging (PCI) setup was used to record the in situ deformation and failure in the specimens. The experiments show that synchrotron X-ray PCI provides a sufficient contrast between the HMX crystals and the doped binder, even at ultrafast recording rates. Under dynamic compression, most of the cracking in the crystals was observed to be due to the tensile stress generated by the diametral compression applied from the contacts between the crystals. Tensile stress driven cracking was also observed for some of the crystals due to the transverse deformation of the binder and superior bonding between the crystal and the binder. The obtained results are vital to develop improved understanding and to validate the macroscopic and mesoscopic numerical models for energetic composites so that eventually hot spot formation can be predicted.