Plamen Punov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Plamen Punov has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Christelle Périlhon
Conservatoire National des Arts et Métiers, CMGPCE, 292 rue Saint Martin, 75003 Paris, France
6 shared publications Teodossi Evtimov
Technical University of Sofia
4 shared publications- Adrian Clenci
Department Automobiles and Transport, Pitești University Centre, National University of Science and Technology Politehnica Bucharest, 1, Tg. din Vale Street, 110040 Pitești, Argeș, Romania
3 shared publications - Nikolay Milkov
Technical University – Sofia, Department of Internal Combustion Engines, Automobiles and Transport, 1000 Sofia, Bulgaria
3 shared publications - Pierre Podevin
Laboratoire de Chimie Moléculaire, Génie des procédés Chimiques et Energétique, EA7341, Conservatoire National des Arts et Métiers, HESAM Université, 75003 Paris, France
3 shared publications Quentin Danel
Conservatoire National des Arts et Métiers
3 shared publications
Latest Publications
- Open Access
- 1 September 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3329 (1)
Numerical study on the engine combustion characteristics of premixed methane ignited by diesel fuel: A comparison between 3D and 0D approach
In this study, premixed methane combustion is studied in a direct-injection diesel engine for passenger cars. The combustion is modelled by means of 3D and 0D approaches using AVL software on a single engine operating point with the same diesel injection strategy, injected fuel quantity, air-excess and EGR ratio. Firstly, a CFD simulation was conducted in AVL Fire considering the real geometry of the combustion chamber ang injector geometry. A combustion model based on the chemical kinetics mechanism of methane and C7H16 was used. As a result, the rate of heat release and in-cylinder pressure were obtained in the combustion phase. Then, a 0D-1D model of the engine was numerically studied in AVL Cruise M considering the same engine operating condition but using 0D combustion model AVL SEW and AVL MCC2014. The same combustion characteristics were estimated and compared to the CFD simulation. Finaly, the combustion models’ constants were optimized for AVL SEW, AVL MCC2014 based on the rate of heat release comparison to the CFD model.
- 1 September 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3329 (1)
Open AccessNumerical study on the engine combustion characteristics of premixed methane ignited by diesel fuel: A comparison between 3D and 0D approach
In this study, premixed methane combustion is studied in a direct-injection diesel engine for passenger cars. The combustion is modelled by means of 3D and 0D approaches using AVL software on a single engine operating point with the same diesel injection strategy, injected fuel quantity, air-excess and EGR ratio. Firstly, a CFD simulation was conducted in AVL Fire considering the real geometry of the combustion chamber ang injector geometry. A combustion model based on the chemical kinetics mechanism of methane and C7H16 was used. As a result, the rate of heat release and in-cylinder pressure were obtained in the combustion phase. Then, a 0D-1D model of the engine was numerically studied in AVL Cruise M considering the same engine operating condition but using 0D combustion model AVL SEW and AVL MCC2014. The same combustion characteristics were estimated and compared to the CFD simulation. Finaly, the combustion models’ constants were optimized for AVL SEW, AVL MCC2014 based on the rate of heat release comparison to the CFD model.
- Open Access
- 12 January 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 121 (1) , 4
Study on the Energy Demand of Vehicle Propulsion to Minimize Hydrogen Consumption: A Case Study for an Ultra-Energy Efficient Fuel Cell EV in Predefined Driving Conditions
Nowadays, the automotive industry is primarily driven by the CO2 policy that targets net zero carbon emissions by 2035 from passenger cars and commercial vehicles. The main path to achieve this goal is the implementation of electric powertrains with the energy stored in batteries, as the case for battery electric vehicles (BEV). However, this technology still faces some difficulties in terms of energy density, overall weight, charging time, and vehicle autonomy. From the other point of view, fuel cell electric vehicles (FCEV) offer the same advantages as BEV in terms of CO2 reduction, providing better autonomy and lower refueling time. The energy demand by the electric powertrain strongly depends on the vehicle driving conditions as it directly affects energy consumption. In that context, the article aims to study the electrical energy demand of an ultra-energy efficient vehicle intended for a Shell eco-marathon competition in order to minimize hydrogen consumption. The study was carried out over a single lap on the racing track in Nogaro, France while applying the race rules from the competition in 2023. It includes a numerical evaluation of the vehicle resistance forces in different driving strategies and experimental validation on the propulsion test bench.
- 12 January 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 121 (1) , 4
Open AccessStudy on the Energy Demand of Vehicle Propulsion to Minimize Hydrogen Consumption: A Case Study for an Ultra-Energy Efficient Fuel Cell EV in Predefined Driving Conditions
Nowadays, the automotive industry is primarily driven by the CO2 policy that targets net zero carbon emissions by 2035 from passenger cars and commercial vehicles. The main path to achieve this goal is the implementation of electric powertrains with the energy stored in batteries, as the case for battery electric vehicles (BEV). However, this technology still faces some difficulties in terms of energy density, overall weight, charging time, and vehicle autonomy. From the other point of view, fuel cell electric vehicles (FCEV) offer the same advantages as BEV in terms of CO2 reduction, providing better autonomy and lower refueling time. The energy demand by the electric powertrain strongly depends on the vehicle driving conditions as it directly affects energy consumption. In that context, the article aims to study the electrical energy demand of an ultra-energy efficient vehicle intended for a Shell eco-marathon competition in order to minimize hydrogen consumption. The study was carried out over a single lap on the racing track in Nogaro, France while applying the race rules from the competition in 2023. It includes a numerical evaluation of the vehicle resistance forces in different driving strategies and experimental validation on the propulsion test bench.
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3064 (1)
Model-based study of the influence of selected parameters on the performance of a low-powered SOFC
Solid oxide fuel cells (SOFCs) are a technology of high efficiency that is often applied in stacks for modern cogeneration systems as a standalone unit, or Solid oxide fuel cells (SOFCs) are a technology of high efficiency that is often applied in stacks for modern cogeneration systems as a standalone unit, or
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3064 (1)
Model-based study of the influence of selected parameters on the performance of a low-powered SOFC
Solid oxide fuel cells (SOFCs) are a technology of high efficiency that is often applied in stacks for modern cogeneration systems as a standalone unit, or Solid oxide fuel cells (SOFCs) are a technology of high efficiency that is often applied in stacks for modern cogeneration systems as a standalone unit, or
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3104 (1)
Thermodynamic analysis of a low-powered SOFC CHP system
Solid oxide fuel cell systems are a novel concept for combined heat and power (CHP) generation with high total efficiency and low emissions of harmful gases. In order to successfully review the operational processes of such a system, thermodynamic analyses are normally employed. The aim of this paper is to propose a SOFC system topology based on a preselected SOFC and determine the heat transfer rates as well as the overall efficiency of the plant by means of a mathematical model. The results indicate a total system efficiency of 0.628 without evaluating the energy available from the combustion of the remaining anode off-gas (AOG). Analysis of the effects of the steam to carbon (S/C) ratio on the system’s behavior and outcomes is also performed. The analysis reveals that increasing the S/C ratio of the system leads to a decrease in the electrical efficiency, while the total efficiency of the system experiences a slight increase.
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3104 (1)
Open AccessThermodynamic analysis of a low-powered SOFC CHP system
Solid oxide fuel cell systems are a novel concept for combined heat and power (CHP) generation with high total efficiency and low emissions of harmful gases. In order to successfully review the operational processes of such a system, thermodynamic analyses are normally employed. The aim of this paper is to propose a SOFC system topology based on a preselected SOFC and determine the heat transfer rates as well as the overall efficiency of the plant by means of a mathematical model. The results indicate a total system efficiency of 0.628 without evaluating the energy available from the combustion of the remaining anode off-gas (AOG). Analysis of the effects of the steam to carbon (S/C) ratio on the system’s behavior and outcomes is also performed. The analysis reveals that increasing the S/C ratio of the system leads to a decrease in the electrical efficiency, while the total efficiency of the system experiences a slight increase.
- 1 January 2022
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2557 (1) , 060002
Combined cycles of SOFC/ICE and SOFC/GT – A brief review
Solid oxide fuel cells (SOFC) are an emerging technology for production of electricity through processing of different fuels such as contemporary diesel or gasoline fuel, natural gas (NG) and hydrogen. SOFC are advantageous over other fuel cells due to their high efficiency (up to 65%), the usage of a cheap catalysts and the low requirements towards the purity of the fuel when hydrogen is utilized. Additionally, SOFC can be combined with an internal combustion engine (ICE) or a gas turbine (GT) to work in combined cycles. The heat engine (HE) utilizes the residual anode-off hydrocarbon-containing gases of the SOFC to guarantee even better efficiencies and higher versatility of the power system over standalone-SOFC and standalone-ICE layouts. Such combined systems can successfully be applied in stationary power or combined heat and power (CHP) generation for remote regions, or where the electricity from the grid is too expensive. They are also a promising concept in the transportation sector, particularly for heavy-duty transport means such as trains, trucks and airplanes. One of the greatest advantages of hybrid cycle systems is that they generate very low amounts of harmful gases, which makes them viable in the context of contemporary strict emission regulations. Namely the basics of the SOFC technology, its possible applications, and the approaches and possible layouts for building a combined cycle with an ICE or a GT, are reviewed. In the publication it is emphasized on the models’ results in order to compare the effectiveness and feasibility of such a setup. The main differences of the systems caused by employment of a particular HE – ICE or GT, are also highlighted.
- 1 January 2022
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2557 (1) , 060002
Combined cycles of SOFC/ICE and SOFC/GT – A brief review
Solid oxide fuel cells (SOFC) are an emerging technology for production of electricity through processing of different fuels such as contemporary diesel or gasoline fuel, natural gas (NG) and hydrogen. SOFC are advantageous over other fuel cells due to their high efficiency (up to 65%), the usage of a cheap catalysts and the low requirements towards the purity of the fuel when hydrogen is utilized. Additionally, SOFC can be combined with an internal combustion engine (ICE) or a gas turbine (GT) to work in combined cycles. The heat engine (HE) utilizes the residual anode-off hydrocarbon-containing gases of the SOFC to guarantee even better efficiencies and higher versatility of the power system over standalone-SOFC and standalone-ICE layouts. Such combined systems can successfully be applied in stationary power or combined heat and power (CHP) generation for remote regions, or where the electricity from the grid is too expensive. They are also a promising concept in the transportation sector, particularly for heavy-duty transport means such as trains, trucks and airplanes. One of the greatest advantages of hybrid cycle systems is that they generate very low amounts of harmful gases, which makes them viable in the context of contemporary strict emission regulations. Namely the basics of the SOFC technology, its possible applications, and the approaches and possible layouts for building a combined cycle with an ICE or a GT, are reviewed. In the publication it is emphasized on the models’ results in order to compare the effectiveness and feasibility of such a setup. The main differences of the systems caused by employment of a particular HE – ICE or GT, are also highlighted.
- Open Access
- 1 January 2022
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 960 (1)
Assessment of the Miller cycle operation in a spark ignition engine via 1D numerical simulation
The article presents the results of a 1D numerical simulation of a spark ignition engine developed to operate in Miller cycle. Miller cycle offers better thermal efficiency compared to Otto cycle due to higher volumetric expansion than compression, which in the current context is of paramount importance. In an engine with fixed geometric compression ratio, Miller cycle operation could be realized by means of either early intake valve closing (EIVC) or late intake valve closing (LIVC). Both cases lead however to a lower volumetric efficiency, thus reducing the indicating mean effective pressure, which in its turn results to a lower power output. The simulation’s aim is not only to assess the impact of implementing the Miller cycle but also to obtain the necessary results for imposing the boundary conditions in a 3D CFD simulation whose purpose is to analyse the influence of the Miller cycle on the internal aerodynamics of the engine.
- 1 January 2022
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 960 (1)
Open AccessAssessment of the Miller cycle operation in a spark ignition engine via 1D numerical simulation
The article presents the results of a 1D numerical simulation of a spark ignition engine developed to operate in Miller cycle. Miller cycle offers better thermal efficiency compared to Otto cycle due to higher volumetric expansion than compression, which in the current context is of paramount importance. In an engine with fixed geometric compression ratio, Miller cycle operation could be realized by means of either early intake valve closing (EIVC) or late intake valve closing (LIVC). Both cases lead however to a lower volumetric efficiency, thus reducing the indicating mean effective pressure, which in its turn results to a lower power output. The simulation’s aim is not only to assess the impact of implementing the Miller cycle but also to obtain the necessary results for imposing the boundary conditions in a 3D CFD simulation whose purpose is to analyse the influence of the Miller cycle on the internal aerodynamics of the engine.
- Open Access
- 1 January 2022
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 960 (1)
Turbocharger surge behavior for sudden valve closing downstream the compressor and effect of actuating variable nozzle turbine
Surge is an unstable phenomenon appearing when a valve closing reduces the compressor flow rate. This phenomenon is avoided for automotive turbochargers by defining a surge margin during powertrain system design. This surge margin established with measurements in steady state testing regime limits the maximal engine torque at low levels of output. An active control of the compressor could reduce the surge margin and facilitate a transient compressor operation for a short time in surge zone. In this paper, an experimental study of the transient operation of a turbocharger compressor entering the surge zone is performed. Control of the turbocharger speed is sought to avoid unsteady operation using the variable geometry turbine (VGT) nozzle actuator. From a given stable operating point, surge is induced by reducing the opening of a valve located downstream of the compressor air circuit. The effect of reducing the speed of rotation by controlling the VGT valve is investigated, as this should lead to more stable compressor operation. The rotation speed of the turbocharger is controlled to avoid an unstable operating point using servo-actuator of variable geometry turbine. From a stable operating point, the surge appearance is caused by closing a butterfly valve downstream the air circuit of the compressor. The effect on the compressor rotation speed when the opening of variable geometry turbocharger valve is modified is studied. Measurements have been conducted for different control profiles of the VGT valve placed downstream the compressor. This article presents the means used to carry out these tests as well as the results of the measurements of the instantaneous signals of pressure, temperature, flow rate and rotation speed, allowing the analysis of the surge phenomenon.
- 1 January 2022
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 960 (1)
Open AccessTurbocharger surge behavior for sudden valve closing downstream the compressor and effect of actuating variable nozzle turbine
Surge is an unstable phenomenon appearing when a valve closing reduces the compressor flow rate. This phenomenon is avoided for automotive turbochargers by defining a surge margin during powertrain system design. This surge margin established with measurements in steady state testing regime limits the maximal engine torque at low levels of output. An active control of the compressor could reduce the surge margin and facilitate a transient compressor operation for a short time in surge zone. In this paper, an experimental study of the transient operation of a turbocharger compressor entering the surge zone is performed. Control of the turbocharger speed is sought to avoid unsteady operation using the variable geometry turbine (VGT) nozzle actuator. From a given stable operating point, surge is induced by reducing the opening of a valve located downstream of the compressor air circuit. The effect of reducing the speed of rotation by controlling the VGT valve is investigated, as this should lead to more stable compressor operation. The rotation speed of the turbocharger is controlled to avoid an unstable operating point using servo-actuator of variable geometry turbine. From a stable operating point, the surge appearance is caused by closing a butterfly valve downstream the air circuit of the compressor. The effect on the compressor rotation speed when the opening of variable geometry turbocharger valve is modified is studied. Measurements have been conducted for different control profiles of the VGT valve placed downstream the compressor. This article presents the means used to carry out these tests as well as the results of the measurements of the instantaneous signals of pressure, temperature, flow rate and rotation speed, allowing the analysis of the surge phenomenon.
- Open Access
- 24 June 2021
- Published by MDPI AG in Electronics
- Vol. 10 (13) , 1530
Model-Based Estimation of Transmission Gear Ratio for Driving Energy Consumption of an EV
This paper presents a numerical study of the effect of the transmission configuration on the energy consumption of an electric vehicle. The first part of this study is related to a vehicle simulation model that takes into consideration vehicle resistances such as aerodynamic, rolling and inertial resistance as well as the traction force. The model was then validated by means of vehicle acceleration time, from 0 to 100 km/h in the case of a single-speed gearbox. Vehicle power demand and electrical energy consumption were then evaluated over three standardized test cycles: WLTC-Class 3, NEDC and FTP-75. For each cycle, two cases were studied: a single-speed and dual-speed gearbox. Very different power demand was observed between the cycles in terms of maximum and average driving power. The most power-demanding cycle was WLTC, while NEDC was less power demanding. However, the specific driving energy per kilometer was very similar for NEDC and FTP-75, as it respectively accounted to 0.118/0.116 kWh/km and 0.117/0.115 kWh/km. WLTC led to a higher specific consumption of 0.127/0.124 kWh/km. A dual-speed gearbox led to better efficiency, within the range of 1.7% to 2.4%. The higher value was obtained for highly dynamic WLTC.
- 24 June 2021
- Published by MDPI AG in Electronics
- Vol. 10 (13) , 1530
Open AccessModel-Based Estimation of Transmission Gear Ratio for Driving Energy Consumption of an EV
This paper presents a numerical study of the effect of the transmission configuration on the energy consumption of an electric vehicle. The first part of this study is related to a vehicle simulation model that takes into consideration vehicle resistances such as aerodynamic, rolling and inertial resistance as well as the traction force. The model was then validated by means of vehicle acceleration time, from 0 to 100 km/h in the case of a single-speed gearbox. Vehicle power demand and electrical energy consumption were then evaluated over three standardized test cycles: WLTC-Class 3, NEDC and FTP-75. For each cycle, two cases were studied: a single-speed and dual-speed gearbox. Very different power demand was observed between the cycles in terms of maximum and average driving power. The most power-demanding cycle was WLTC, while NEDC was less power demanding. However, the specific driving energy per kilometer was very similar for NEDC and FTP-75, as it respectively accounted to 0.118/0.116 kWh/km and 0.117/0.115 kWh/km. WLTC led to a higher specific consumption of 0.127/0.124 kWh/km. A dual-speed gearbox led to better efficiency, within the range of 1.7% to 2.4%. The higher value was obtained for highly dynamic WLTC.
- 1 June 2021
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 46 (38) , 20291-20302
Energy management of a fuel cell hybrid ultra-energy efficient vehicle
- 1 June 2021
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 46 (38) , 20291-20302
Energy management of a fuel cell hybrid ultra-energy efficient vehicle
- 1 January 2021
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2439 (1) , 020004
Hydrogen production, storage and delivery in regards to automotive applications – A brief review
The paper focuses on hydrogen production, storage and transportation as it is an important resource to be used in the energy and mobility sectors due to the worldwide increase in the demand for clean energy and the recently applied policies regarding carbon-neutrality. The basics of the most popular technologies and the conditions for storage and transportation of hydrogen, with their differences, advantages and disadvantages are discussed. The most suitable technology in regards to hydrogen utilization in automotive applications is emphasized. Examples of contemporary hydrogen-driven commercial fuel cell vehicles are also discussed.
- 1 January 2021
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2439 (1) , 020004
Hydrogen production, storage and delivery in regards to automotive applications – A brief review
The paper focuses on hydrogen production, storage and transportation as it is an important resource to be used in the energy and mobility sectors due to the worldwide increase in the demand for clean energy and the recently applied policies regarding carbon-neutrality. The basics of the most popular technologies and the conditions for storage and transportation of hydrogen, with their differences, advantages and disadvantages are discussed. The most suitable technology in regards to hydrogen utilization in automotive applications is emphasized. Examples of contemporary hydrogen-driven commercial fuel cell vehicles are also discussed.