Ignacio Trojaola
Ignacio Trojaola has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Iker Elorza
4 shared publicationsAron Pujana-Arrese
Ikerlan Technology Research Centre, Arrasate-Mondragón, Gipuzkoa, Spain
3 shared publications- Eloy Irigoyen
Universidad del País Vasco (UPV/EHU)
3 shared publications - Iker Elorza
IKERLAN, Pº. J. Mª. Arizmendiarrieta, 2, 20500 Arrasate-Mondragón, Gipuzkoa, Spain
3 shared publications Aron Pujana
Ikerlan Technology Research Center
2 shared publicationsCarlos Calleja
Ikerlan Technology Research Centre, Basque Research and Technology Alliance (BRTA), P.J.M. Arizmendiarrieta, 2, 20500, Arrasate/Mondragón
2 shared publications
Latest Publications
- Open Access
- 9 May 2024
- Published by Elsevier in Results in Engineering
- Vol. 22
On the effects of pitch system faults on a wind turbine
- 9 May 2024
- Published by Elsevier in Results in Engineering
- Vol. 22
Open AccessOn the effects of pitch system faults on a wind turbine
- Open Access
- 28 August 2023
- Published by Universidade da Coruna
- p. 186-191
Modelado integrado de fuerzas y motores de inducción aplicado al proceso de fresado
Resumen En este artículo se propone un modelo para el proceso de fresado que integra el modelado de los actuadores de la fresadora y las fuerzas generadas durante dicho proceso. El modelado de las fuerzas se realiza directamente a partir de los componentes de fuerza tangencial, axial y radial. Además, se desarrolla el modelado matemático de los motores de inducción, encargados de realizar el control de posición y velocidad de la fresadora. El modelado se lleva a cabo utilizando la librería Simscape de MATLAB, lo que proporciona una herramienta intuitiva y reproducible para simular el proceso de fresado bajo diferentes condiciones de ensayo. Los resultados de las simulaciones muestran cómo las dinámicas de los motores de inducción se ven afectadas por las fuerzas y los pares generados durante el proceso, lo cual permite adecuar los lazos de control de los motores a ellas.
- 28 August 2023
- Published by Universidade da Coruna
- p. 186-191
Open AccessModelado integrado de fuerzas y motores de inducción aplicado al proceso de fresado
Resumen En este artículo se propone un modelo para el proceso de fresado que integra el modelado de los actuadores de la fresadora y las fuerzas generadas durante dicho proceso. El modelado de las fuerzas se realiza directamente a partir de los componentes de fuerza tangencial, axial y radial. Además, se desarrolla el modelado matemático de los motores de inducción, encargados de realizar el control de posición y velocidad de la fresadora. El modelado se lleva a cabo utilizando la librería Simscape de MATLAB, lo que proporciona una herramienta intuitiva y reproducible para simular el proceso de fresado bajo diferentes condiciones de ensayo. Los resultados de las simulaciones muestran cómo las dinámicas de los motores de inducción se ven afectadas por las fuerzas y los pares generados durante el proceso, lo cual permite adecuar los lazos de control de los motores a ellas.
- Open Access
- 27 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 146850-146867
An Innovative MIMO Iterative Learning Control Approach for the Position Control of a Hydraulic Press
To improve the performance of hydraulic press position control and eliminate the need to manually define control signals, this paper proposes a multi-input-multi-output (MIMO) Iterative Learning Control (ILC) algorithm. The MIMO ILC algorithm design is based on the inversion of the known low frequency dynamics of the hydraulic press, whereas the unknown and uncertain high frequency dynamics are discarded due to their low influence in the learning transient. Moreover, for the MIMO ILC convergence condition, a graphical method is proposed, in which the ILC learning filter eigenvalues are analyzed. This method allows studying the stability and convergence rate of the algorithm intuitively. Theoretical analysis and results prove that with the MIMO ILC algorithm the position control is automated and that high precision in the position tracking is gained. A comparison with other model inverse ILC approaches is carried out and it is shown that the proposed MIMO ILC algorithm outperforms the existing algorithms, reducing the number of iterations required to converge while guaranteeing system stability. Furthermore, experimental results in a hydraulic test rig are presented and compared to those obtained with a conventional PI controller.
- 27 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 146850-146867
Open AccessAn Innovative MIMO Iterative Learning Control Approach for the Position Control of a Hydraulic Press
To improve the performance of hydraulic press position control and eliminate the need to manually define control signals, this paper proposes a multi-input-multi-output (MIMO) Iterative Learning Control (ILC) algorithm. The MIMO ILC algorithm design is based on the inversion of the known low frequency dynamics of the hydraulic press, whereas the unknown and uncertain high frequency dynamics are discarded due to their low influence in the learning transient. Moreover, for the MIMO ILC convergence condition, a graphical method is proposed, in which the ILC learning filter eigenvalues are analyzed. This method allows studying the stability and convergence rate of the algorithm intuitively. Theoretical analysis and results prove that with the MIMO ILC algorithm the position control is automated and that high precision in the position tracking is gained. A comparison with other model inverse ILC approaches is carried out and it is shown that the proposed MIMO ILC algorithm outperforms the existing algorithms, reducing the number of iterations required to converge while guaranteeing system stability. Furthermore, experimental results in a hydraulic test rig are presented and compared to those obtained with a conventional PI controller.
- 2 November 2020
- Published by Oxford University Press (OUP) in Logic Journal of the IGPL
- Vol. 30 (2) , 214-226
The Effect of Iterative Learning Control on the Force Control of a Hydraulic Cushion
An iterative learning control (ILC) algorithm is presented for the force control circuit of a hydraulic cushion. A control scheme consisting of a PI controller, feed-forward (FF) and feedback-linearization is first derived. The uncertainties and nonlinearities of the proportional valve, the main system actuator, prevent the accurate tracking of the pressure reference signal. Therefore, an extra ILC FF signal is added to counteract the valve model uncertainties. The unknown valve dynamics are attenuated by adding a fourth-order low-pass filter to the iterative learning control design, which is split up into two second-order low-pass filters to carry out forward and backward filtering and obtain zero-phase filtering. The addition of the ILC signal presents significant improvements in terms of settling time and overshoot of the pressure signal in the cylinder.
- 2 November 2020
- Published by Oxford University Press (OUP) in Logic Journal of the IGPL
- Vol. 30 (2) , 214-226
The Effect of Iterative Learning Control on the Force Control of a Hydraulic Cushion
An iterative learning control (ILC) algorithm is presented for the force control circuit of a hydraulic cushion. A control scheme consisting of a PI controller, feed-forward (FF) and feedback-linearization is first derived. The uncertainties and nonlinearities of the proportional valve, the main system actuator, prevent the accurate tracking of the pressure reference signal. Therefore, an extra ILC FF signal is added to counteract the valve model uncertainties. The unknown valve dynamics are attenuated by adding a fourth-order low-pass filter to the iterative learning control design, which is split up into two second-order low-pass filters to carry out forward and backward filtering and obtain zero-phase filtering. The addition of the ILC signal presents significant improvements in terms of settling time and overshoot of the pressure signal in the cylinder.
- 1 January 2020
- Published by Elsevier in IFAC-PapersOnLine
- Vol. 53 (2) , 1421-1426
Iterative Learning Control and Gaussian Process Regression for Hydraulic Cushion Control
- 1 January 2020
- Published by Elsevier in IFAC-PapersOnLine
- Vol. 53 (2) , 1421-1426
Iterative Learning Control and Gaussian Process Regression for Hydraulic Cushion Control
- Open Access
- 1 September 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 753 (5) , 052008
On the effects of basic platform design characteristics on floating offshore wind turbine control and their mitigation
Semi-submersible floating offshore wind turbines present significant advantages over other designs in terms of cost, deployment, maintenance and site-independence. However, these advantages are achieved by shifting a part of the burden of stabilising the platform pitch and roll motions to the turbine control system. A study is presented here of the effects of basic platform dimensions on the performance of a standard pitch controller and the possible methods for mitigating said effects.
- 1 September 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 753 (5) , 052008
Open AccessOn the effects of basic platform design characteristics on floating offshore wind turbine control and their mitigation
Semi-submersible floating offshore wind turbines present significant advantages over other designs in terms of cost, deployment, maintenance and site-independence. However, these advantages are achieved by shifting a part of the burden of stabilising the platform pitch and roll motions to the turbine control system. A study is presented here of the effects of basic platform dimensions on the performance of a standard pitch controller and the possible methods for mitigating said effects.