Scott N. Roberts
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Scott N. Roberts has a total of 73 co-authors. Here are the top co-authors by number of shared publications:
- Douglas C. Hofmann
NASA Jet Propulsion Laboratory California Institute of Technology Pasadena CA 91109 USA
8 shared publications William L. Johnson
Keck Laboratory of Engineering Sciences, California Institute of Technology, 1200 E. California Blvd., Pasadena CA 91125, USA
8 shared publicationsDouglas C. Hofmann
5 shared publications- Beomjin Kwon
School for Engineering of Matter, Transport and Energy, Arizona State University 1 , Tempe, Arizona 85287
4 shared publications Elham Maghsoudi
4 shared publicationsHenry Kozachkov
4 shared publications
Latest Publications
- Open Access
- 1 November 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (11) , 110540
Development and Evaluation of High Specific Energy Li/CF x Cylindrical Battery Cells for Space Applications
Cylindrical Li/CF x battery cells were developed and evaluated for use in robotic space applications. These cells feature lithium anodes coupled with high specific capacity (∼865 mAh g −1 theoretical value) fluorinated carbon or CF x cathodes (where x∼1). The development efforts targeted achieving a cell level specific energy of >700 Wh kg −1 (when discharged at moderate rates at 20 °C) in a hermetically sealed D-sized cell format, at a typical discharge voltage of ∼2.6 V. The Jet Propulsion Laboratory collaborated with two different vendors (EaglePicher Technologies and Rayovac) to develop these cells, through the use of high loading CF x cathodes to maximize the delivered capacity combined with aluminum packaging to reduce cell mass (relative to traditional stainless steel designs). Cells were tested over a range of relevant rates and temperatures, to establish performance characteristics. Constant current discharge tests were performed under pulse conditions to extract the internal cell resistance, and three-electrode cells were prepared and tested to study the effects of depassivation and aging. Thermal power generation was measured under both open circuit voltage conditions (using microcalorimetry) and at different discharge rates (using isothermal calorimetry). Thermal imaging was also performed, to estimate cell temperatures during discharge.
- 1 November 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (11) , 110540
Open AccessDevelopment and Evaluation of High Specific Energy Li/CF x Cylindrical Battery Cells for Space Applications
Cylindrical Li/CF x battery cells were developed and evaluated for use in robotic space applications. These cells feature lithium anodes coupled with high specific capacity (∼865 mAh g −1 theoretical value) fluorinated carbon or CF x cathodes (where x∼1). The development efforts targeted achieving a cell level specific energy of >700 Wh kg −1 (when discharged at moderate rates at 20 °C) in a hermetically sealed D-sized cell format, at a typical discharge voltage of ∼2.6 V. The Jet Propulsion Laboratory collaborated with two different vendors (EaglePicher Technologies and Rayovac) to develop these cells, through the use of high loading CF x cathodes to maximize the delivered capacity combined with aluminum packaging to reduce cell mass (relative to traditional stainless steel designs). Cells were tested over a range of relevant rates and temperatures, to establish performance characteristics. Constant current discharge tests were performed under pulse conditions to extract the internal cell resistance, and three-electrode cells were prepared and tested to study the effects of depassivation and aging. Thermal power generation was measured under both open circuit voltage conditions (using microcalorimetry) and at different discharge rates (using isothermal calorimetry). Thermal imaging was also performed, to estimate cell temperatures during discharge.
- 25 October 2025
- Published by Elsevier in Thermal Science and Engineering Progress
- Vol. 67
Flow visualization of adjoint-optimized pin fin arrays fabricated by additive manufacturing
- 25 October 2025
- Published by Elsevier in Thermal Science and Engineering Progress
- Vol. 67
Flow visualization of adjoint-optimized pin fin arrays fabricated by additive manufacturing
- 31 May 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 250
Micro-Xray Tomography based pore-scale simulation of additively manufactured wicks
- 31 May 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 250
Micro-Xray Tomography based pore-scale simulation of additively manufactured wicks
- 22 February 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 242
Designing pin fin heat sinks with restarting adjoint optimization approach
- 22 February 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 242
Designing pin fin heat sinks with restarting adjoint optimization approach
- 18 December 2022
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 202
Shape optimization of pin fin array in a cooling channel using genetic algorithm and machine learning
- 18 December 2022
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 202
Shape optimization of pin fin array in a cooling channel using genetic algorithm and machine learning
- 1 June 2021
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 149 (6) , 4327-4336
Acoustic measurement and statistical characterization of direct-printed, variable-porosity aluminum foams
Additive manufacturing has expanded greatly in recent years with the promise of being able to create complex and custom structures at will. Enhanced control over the microstructure properties, such as percent porosity, is valuable to the acoustic design of materials. In this work, aluminum foams are fabricated using a modified powder bed fusion method, which enables voxel-by-voxel printing of structures ranging from fully dense to approximately 50% porosity. To understand the acoustic response, samples are measured in an acoustic impedance tube and characterized with the Johnson–Champoux–Allard–Lafarge model for rigid-frame foams. Bayesian statistical inversion of the model parameters is performed to assess the applicability of commonly employed measurement and modeling methods for traditional foams to the additively manufactured, low porosity aluminum foams. This preliminary characterization provides insights into how emerging voxel-by-voxel additive manufacturing approaches could be used to fabricate acoustic metal foams and what could be learned about the microstructure using traditional measurement and analysis techniques.
- 1 June 2021
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 149 (6) , 4327-4336
Acoustic measurement and statistical characterization of direct-printed, variable-porosity aluminum foams
Additive manufacturing has expanded greatly in recent years with the promise of being able to create complex and custom structures at will. Enhanced control over the microstructure properties, such as percent porosity, is valuable to the acoustic design of materials. In this work, aluminum foams are fabricated using a modified powder bed fusion method, which enables voxel-by-voxel printing of structures ranging from fully dense to approximately 50% porosity. To understand the acoustic response, samples are measured in an acoustic impedance tube and characterized with the Johnson–Champoux–Allard–Lafarge model for rigid-frame foams. Bayesian statistical inversion of the model parameters is performed to assess the applicability of commonly employed measurement and modeling methods for traditional foams to the additively manufactured, low porosity aluminum foams. This preliminary characterization provides insights into how emerging voxel-by-voxel additive manufacturing approaches could be used to fabricate acoustic metal foams and what could be learned about the microstructure using traditional measurement and analysis techniques.
- 26 June 2018
- Published by Wiley in Advanced Engineering Materials
- Vol. 20 (10)
Developing Processing Parameters and Characterizing Microstructure and Properties of an Additively Manufactured FeCrMoBC Metallic Glass Forming Alloy
Powder bed fusion (PBF) processing parameters are developed for a FeCrMoBC glass‐forming alloy. Although bulk metallic glass parts are successfully fabricated using additive manufacturing, the porosity is too high for imparting good mechanical properties. The processing is tuned to create a fully‐dense, dendrite‐reinforced metal‐matrix composite with low hardness and high indentation fracture toughness. Microstructures and properties of the printed alloy are compared to bulk amorphous samples made through thermal spray additive manufacturing (TSAM). The work shows that printing glass‐forming alloys can result in tunable properties based on the cooling rate, porosity, and composite microstructures.
- 26 June 2018
- Published by Wiley in Advanced Engineering Materials
- Vol. 20 (10)
Developing Processing Parameters and Characterizing Microstructure and Properties of an Additively Manufactured FeCrMoBC Metallic Glass Forming Alloy
Powder bed fusion (PBF) processing parameters are developed for a FeCrMoBC glass‐forming alloy. Although bulk metallic glass parts are successfully fabricated using additive manufacturing, the porosity is too high for imparting good mechanical properties. The processing is tuned to create a fully‐dense, dendrite‐reinforced metal‐matrix composite with low hardness and high indentation fracture toughness. Microstructures and properties of the printed alloy are compared to bulk amorphous samples made through thermal spray additive manufacturing (TSAM). The work shows that printing glass‐forming alloys can result in tunable properties based on the cooling rate, porosity, and composite microstructures.
- Open Access
- 24 November 2016
- Published by Springer Nature in Scientific Reports
- Vol. 6 (1) , 37773
Castable Bulk Metallic Glass Strain Wave Gears: Towards Decreasing the Cost of High-Performance Robotics
The use of bulk metallic glasses (BMGs) as the flexspline in strain wave gears (SWGs), also known as harmonic drives, is presented. SWGs are unique, ultra-precision gearboxes that function through the elastic flexing of a thin-walled cup, called a flexspline. The current research demonstrates that BMGs can be cast at extremely low cost relative to machining and can be implemented into SWGs as an alternative to steel. This approach may significantly reduce the cost of SWGs, enabling lower-cost robotics. The attractive properties of BMGs, such as hardness, elastic limit and yield strength, may also be suitable for extreme environment applications in spacecraft.
- 24 November 2016
- Published by Springer Nature in Scientific Reports
- Vol. 6 (1) , 37773
Open AccessCastable Bulk Metallic Glass Strain Wave Gears: Towards Decreasing the Cost of High-Performance Robotics
The use of bulk metallic glasses (BMGs) as the flexspline in strain wave gears (SWGs), also known as harmonic drives, is presented. SWGs are unique, ultra-precision gearboxes that function through the elastic flexing of a thin-walled cup, called a flexspline. The current research demonstrates that BMGs can be cast at extremely low cost relative to machining and can be implemented into SWGs as an alternative to steel. This approach may significantly reduce the cost of SWGs, enabling lower-cost robotics. The attractive properties of BMGs, such as hardness, elastic limit and yield strength, may also be suitable for extreme environment applications in spacecraft.
- 4 October 2016
- Published by Wiley in Advanced Engineering Materials
- Vol. 19 (1)
Optimizing Bulk Metallic Glasses for Robust, Highly Wear‐Resistant Gears
Despite their promising mechanical properties and ability to be manufactured like plastics, bulk metallic glasses (BMGs) are slow to emerge as a structural engineering material. Because BMGs properties are highly correlated with processing, it is necessary to test them in a relevant engineering application. In the current work, CuZr‐based BMGs are developed with excellent wear performance when used as gears. It is shown that in order to optimize the wear performance of these gears, toughness should be maximized. This contrasts the conventional design strategy, where wear performance increases with increasing hardness. Finally, a new low‐cost manufacturing method for casting net‐shaped macroscale gears is developed.
- 4 October 2016
- Published by Wiley in Advanced Engineering Materials
- Vol. 19 (1)
Optimizing Bulk Metallic Glasses for Robust, Highly Wear‐Resistant Gears
Despite their promising mechanical properties and ability to be manufactured like plastics, bulk metallic glasses (BMGs) are slow to emerge as a structural engineering material. Because BMGs properties are highly correlated with processing, it is necessary to test them in a relevant engineering application. In the current work, CuZr‐based BMGs are developed with excellent wear performance when used as gears. It is shown that in order to optimize the wear performance of these gears, toughness should be maximized. This contrasts the conventional design strategy, where wear performance increases with increasing hardness. Finally, a new low‐cost manufacturing method for casting net‐shaped macroscale gears is developed.