Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Senai Yalçinkaya has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Systematic Analysis and Design Approach for Tribological Behavior in Composite Materials

    by Dudu Mertgenç Yoldaş, Senai Yalçınkaya, Mehmet Fatih Yoldaş

    The tribological behavior of composite materials represents a crucial research domain in modern engineering due to the decisive impact of friction, wear, and surface interactions on operational performance. This study evaluates the material and operating-condition-dependent parameters that dictate the tribological response of composite materials, alongside their predominant wear mechanisms. A comprehensive synthesis of the literature demonstrates that matrix and reinforcement types, filler fraction, fiber orientation, surface topography, interfacial bonding strength, applied load, sliding velocity, and operating temperature significantly govern both the coefficient of friction and wear characteristics. While fiber reinforcement substantially enhances wear resistance when paired with strong interfacial adhesion, weak interfacial bonding accelerates failure mechanisms such as delamination and matrix/particle debonding. Depending on the operational conditions, composites exhibit competing wear mechanisms, including abrasive, adhesive, fatigue, and tribochemical wear. Furthermore, surface engineering strategies such as protective coatings, surface texturing, thermal treatments, and advanced lubrication effectively optimize tribological performance. Notably, hybrid composites incorporating solid lubricant additives demonstrate exceptional potential in minimizing friction and retarding wear rates. Integrating standard empirical testing (e.g., pin-on-disk and block-on-ring) with numerical simulations, finite element analysis (FEA), and artificial intelligence (AI)-assisted modeling offers a robust framework for enhancing design reliability. Overall, achieving optimal tribological performance in composite materials necessitates a holistic design approach that synergizes intrinsic material selection, tailored surface engineering, and operational constraints.

  • Open Access

    Use of Composite Materials in Wind Turbine Blades: A Comprehensive Review

    by Dudu Mertgenç Yoldaş, Senai Yalçinkaya, Mehmet Fatih Yoldaş

    The increasing demand for sustainable energy has accelerated the development of high-performance wind turbine systems. In this context, material selection for turbine blades plays a critical role in ensuring structural efficiency, fatigue resistance, and long-term reliability. This study evaluates the mechanical and structural advantages of carbon fiber-reinforced polymer (CFRP) composites over glass fiber-reinforced polymer (GFRP) materials in wind turbine blade applications. Results from the literature indicate that CFRP provides significantly higher stiffness-to-weight and strength-to-weight ratios, enabling weight reductions of 20-30% in critical blade components such as spar caps. This reduction improves aeroelastic stability, decreases fatigue loading, and enhances overall energy capture efficiency. Furthermore, CFRP exhibits superior fatigue resistance under cyclic loading conditions exceeding 108 cycles, which is essential for the typical 20-30 years service life of wind turbines. However, the higher cost of CFRP remains a limiting factor, leading to its selective use in load-critical regions. The findings suggest that hybrid material strategies combining GFRP and CFRP offer an optimal balance between cost and performance.


  • Open Access

    Experimental Investigation of Four-Point Bending Test Results of GFRP and CFRP Composites Used in Wind Turbine Blades

    by Senai Yalçinkaya, Mehmet Fatih Yoldaş, Dudu Mertgenç Yoldaş

    The depletion of fossil fuels and the rise of environmental concerns have increased the importance of renewable energy sources, positioning wind energy as a key alternative. Modern wind turbine blades are predominantly manufactured from composite materials due to their light weight, high strength, and resistance to corrosion. In offshore applications, approximately 95% of the composite content is glass fiber-reinforced polymer (GFRP), while the remaining 5% is carbon fiber-reinforced polymer (CFRP). GFRP is favored for its low cost and fatigue resistance, whereas CFRP offers superior strength and stiffness but is limited by high production costs. This study investigates the durability of adhesively bonded GFRP and CFRP joints under marine exposure. Seven-layer GFRP and eight-layer CFRP laminates were produced using a 90° unidirectional twill weave and prepared in accordance with ASTM D5868-01. Specimens were immersed in natural Aegean Sea water (21 °C, salinity 3.3–3.7%) for 1, 2, and 3 months. Measurements revealed that GFRP absorbed significantly more moisture (1.02%, 2.97%, 3.78%) than CFRP (0.49%, 0.76%, 0.91%). Four-point bending tests conducted according to ASTM D790 showed reductions in Young’s modulus of up to 9.45% for GFRP and 3.48% for CFRP. Scanning electron microscopy (SEM) confirmed that moisture-induced degradation was more severe in GFRP joints compared to CFRP. These findings highlight the critical role of environmental exposure in the mechanical performance of marine composite joints.


  • Open Access

    Experimental Investigation of Damage to Polymer Glass and Carbon Compo-Sites Used in Wind Turbine Blades as a Result of Four-Point Bending Test

    by Senai Yalçinkaya, Mehmet Fatih Yoldaş, Dudu Mertgenç Yoldaş

    The decline in fossil fuels and environmental pollution have made renewable energy sources essential. In this context, solar and wind energy have come to the forefront to re-duce carbon emissions. While wind energy was previously used for agriculture and water pumping, today its largest contribution is electricity generation. It is rapidly gaining pop-ularity due to its environmental friendliness and affordability. Wind turbines consist of a tower, rotor, shaft, generator, and blades. Blades are critical for system efficiency and en-vironmental protection. While metal materials were initially used, composite materials have now been adopted. Composites offer properties such as light weight, durability, cor-rosion resistance, and long life. Approximately 95% of the composite material used in tur-bine blades is glass fiber and 5% is carbon fiber. The reasons for the preference of glass fi-ber-reinforced composites (GFRP) are low cost, light weight, easy raw material supply, and high mechanical strength. It also offers advantages such as impact resistance, fatigue life, corrosion resistance, and easy shaping during production. Thanks to these properties, glass fiber offers both an economical and structurally safe solution for large-scale blades. The aim of this study is to experimentally investigate the damage processes occurring in the adhesively bonded areas of fiber-reinforced polymer composite materials commonly used in offshore wind turbine blades. Carbon fiber-reinforced composites (CFRP) offer significantly higher strength and stiffness than glass fiber, enabling them to carry the same loads with thinner and lighter structures. However, due to its higher cost and more complex manufacturing process, the use of car-bon fiber is limited. It is generally used in specialized turbines or blade tips requiring high performance. While glass fiber offers an ideal solution for general use, carbon fiber is pre-ferred to a lesser extent as a support or complement in critical areas. GFRP and CFRP specimens were prepared as 7-layer and 8-layer laminates, respectively, using unidirec-tional twill weave with a 90° orientation. A total of 24 specimens were cut according to ASTM D5868-01. Epoxy and hardener were applied to the prepregs by hand lay-up, fol-lowed by a one-day curing process. After resin gelation, the composites were produced using a hot press method. To examine the marine performance of adhesively bonded joints, commonly used in offshore wind turbine blades, single-layer adhesively bonded specimens were conditioned in separate containers for 1, 2, and 3 months in natural sea-water obtained from the Aegean Sea at 21.0°C and with a salinity of 3.3–3.7%. During this period, the moisture absorption of the joints was weighed periodically using high-precision scales. The obtained data was compared with dry reference samples to characterize the moisture absorption behavior in terms of weight change (%). To evaluate the mechanical strength of the specimens under the influence of humidity, four-point bending tests were conducted in accordance with the ASTM D790 standard. The damage types and microstructural deteriorations observed during the tests were examined in detail using a ZEISS GEMINI SEM 560 scanning electron microscope (SEM), which pro-vides high-resolution imaging. These analyses provided comprehensive experimental findings regarding the physical and mechanical effects on adhesively bonded composite joints. In the experimental studies, maximum moisture absorption in GFRP specimens was: After 1, 2, and 3 months of seawater exposure, the moisture absorption rates were measured as 1.02%, 2.97%, and 3.78%, respectively. In CFRP samples tested under the same conditions, the moisture absorption rates were determined as 0.49%, 0.76%, and 0.91%, respectively. According to the results of the four-point bending tests, Young's modulus in GFRP sing-le-lap adhesively bonded joints decreased by 3.15%, 6.42%, and 9.45% for the respective durations compared to specimens tested in a dry environment. Similarly, Young's modu-lus in CFRP single-lap joints decreased by 1.29%, 2.62%, and 3.48% depending on the du-ration of moisture exposure. These results demonstrate that environmental conditions, particularly those of GFRP materials, have a more pronounced impact on their mechanical performance.

  • Open Access

    Experimental Investigation of the Effect of Seawater on Glass and Carbon Fiber Composites via Mechanical Characterization

    by Senai Yalçınkaya, Dudu Mertgenç Yoldaş, Mehmet Fatih Yoldaş

    Since composite materials are light and corrosion-resistant, they have replaced many traditional materials in the aviation and marine industries. Composite materials have the advantages of a much higher strength–weight ratio, lower maintenance requirements, and the ability to form complex shapes, such as bodies, compared to carbon steel. In this study, the mechanical properties of glass fiber reinforced (GFRP) and carbon fiber reinforced (CFRP) composite materials were investigated in marine applications in which composite materials had been used. In this study, 0/90 oriented twill weave eight-ply GFRP and eight-ply CFRP composite materials were used, incorporating the hand lay-up method and hot-pressing method. Seawater was taken from the Aegean Sea, Izmir Province (Balçova/İnciraltı), and had an average temperature of 22.43 °C. This seawater was kept in different containers for 30 days and 60 days (a total of 1440 h of keeping in seawater) with the intent to test the GFRP and CFRP composite samples separately. The produced CFRP and GFRP sheets were then cut with a wet (circular) saw in accordance with the standard procedure in the Composite Research and Testing Laboratory of the Dokuz Eylul University Department of Mechanical Engineering. Moisture retention percentages and Charpy impact tests were carried out. Then, three-point bending tests were carried out according to TS EN ISO 14125. The damage in the material was examined using a ZEISS Stereo Discovery.V12 imaging microscope (Oberkochen, Germany). The mechanical properties of CFRP- and GFRP-reinforced composite samples before and after aging were investigated using the Charpy impact test and three-point bending test. Then, the effects of the seawater environment on the mechanical properties of the CFRP and GFRP composite materials were evaluated by comparing the results. The aim was to better understand what kind of damage would occur in GFRP and CFRP composite materials given the effects of seawater and at what stages changes would occur in the mechanical properties of these materials. Moisture retention rates (%) in the tested samples after the Charpy impact test were 2.56% in GFRP and 0.47% in CFRP after 30 days. In the tested samples after the three-point bending test, these values were 1.41% in GFRP and 0.31% in CFRP after 30 days. Subsequent to the Charpy impact tests, the fracture toughness values of the CFRP samples tested at the 30 J impact energy level before aging in seawater conditions for 30 days or 60 days were found to be increased by 15.79% and 21.08%, respectively. The fracture toughness values of the GFRP tested at the 30 J impact energy level in dry conditions and kept in seawater for 30 days or 60 days were found to be 27.69% and 29.23%, respectively. The energy absorbed during the impact tests by the GFRP samples was higher than in the CFRP samples. This showed that the GFRP samples were more brittle. Subsequent to the three-point bending tests, the CFRP composite samples kept in seawater for periods of 30 days and 60 days showed changes in the modulus of elasticity of 7.48% and 7.46%, respectively, compared to the dry samples. The GFRP composite samples kept in seawater for periods of 30 days and 60 days showed changes in the modulus of elasticity of 7.015% and 11.53%, respectively, compared to the dry samples. The change in the modulus of elasticity was less in the CFRP samples than in GFRP. All of these results showed that the mechanical properties of CFRP were better than those of GFRP.


  • Open Access

    FROM THE HERITAGE OF THE PAST TO THE URBAN SPACES OF THE FUTURE WITH ARTIFICIAL INTELLIGENCE AND THE CODES OF TIME

    by Ozan Düz, Oğuz Düz, Senai Yalçinkaya

    Objective: This study aims to examine the relationship established by artificial intelligence technologies with the historical accumulation in urban space production from the past to the present. The metaphor of ‘codes of time’ refers to the analysis of past cultural and spatial data using digital tools and the reinterpretation of this data in a way that will guide future urban design. Scope: The research covers artificial intelligence-based applications in fields such as urban planning, architecture, digital humanities, and data science. In particular, the role of artificial intelligence in the processes of preserving and repurposing cultural heritage and designing new urban spaces has been evaluated from an interdisciplinary perspective. Method: Qualitative content analysis was used in the study. Publications, theses, projects, and reports indexed in national and international academic databases were examined, and the data obtained were classified under thematic headings. Results: The analyses show that AI-based techniques such as simulation, digital twin, automatic mapping, and morphological analysis play an important role in interpreting historical data and ensuring spatial continuity. It has been determined that these techniques support sustainable urban visions while preserving cultural identity. Conclusion: Artificial intelligence is considered not only a technical tool in urban design, but also a way of thinking that strengthens cultural continuity. The study presents a unique theoretical framework that preserves urban identity and develops innovative spatial paradigms for the future through the interpretation of historical data in a digital environment.

  • Open Access

    A LITERATURE REVIEW ON THE USE OF ARTIFICIAL INTELLIGENCE-SUPPORTED PERFORMANCE ANALYSIS SYSTEMS IN AMATEUR AND PROFESSIONAL ATHLETES

    by Oğuz Düz, Senai Yalçinkaya

    Objective: This study examines the use of artificial intelligence-supported performance analysis systems in amateur and professional athletes, comparing existing technologies and evaluating trends in the literature within a comprehensive framework. The increasing use of artificial intelligence-based tools in sports science enables the objectification of training processes and the multidimensional measurement of performance. Therefore, this study details the contributions of artificial intelligence-based analysis systems to sports and the limitations encountered. Scope: The research covers a broad literature spanning multiple sports disciplines (soccer, basketball, swimming, athletics, racket sports, combat sports, etc.) through academic articles, technical reports, and experimental studies published between 2015 and 2025. The studies examined focus on areas such as motion analysis, injury risk prediction, load tracking, biomechanical measurements, computer vision-based performance evaluation, and machine learning-based decision support processes. Method: The literature review was conducted using a systematic approach. Databases such as IEEE Xplore, PubMed, Scopus, and Google Scholar were searched using the keywords "AI-based performance analysis," "machine learning in sports," and "computer vision athlete monitoring." Studies containing experimental findings, clearly defining artificial intelligence methods, and aiming to measure athlete performance were selected as inclusion criteria. Conclusion: The data obtained after the literature review shows that AI-supported performance analysis systems can measure with high accuracy, especially in professional sports. It reveals that they particularly improve decision-making processes and accelerate technical development. Computer vision methods stand out in motion analysis and technical error detection, while machine learning models excel in performance prediction, load analysis, and injury risk prediction. Low data quality in amateur athletes, equipment costs, and problems accessing expert support were identified as significant limitations. Overall, AI systems show strong potential for increasing training efficiency, providing personalized feedback, and reducing injury risk. However, ethical responsibilities, data privacy, and the lack of low-cost, accessible models are key research areas to be addressed in the future.

  • Open Access

    NEW ERA IN HEALTH WITH ARTIFICIAL INTELLIGENCE AND DIGITAL REVOLUTION IN MEDICINE

    by Oğuz Düz, Senai Yalçinkaya, Saliha Özpinar, Dilek Öztaş, Ümran Sevi̇l, Ayhan Aytaç

    This study provides a comprehensive overview of the impact of artificial intelligence (AI) and the digital revolution on the healthcare sector. AI-enabled systems have transformed many areas from patient diagnosis to treatment processes, from healthcare management to cost minimisation. Method: The main objective of the study is to analyse the strengths and weaknesses, opportunities and threats of artificial intelligence in healthcare. With the increasing use of artificial intelligence in the health sector, changes in areas such as diagnostic accuracy, treatment processes, patient safety and cost effectiveness are evaluated. Scope: The effects of artificial intelligence on the health sector between 2015-2025 have been examined and the transformation it provides in terms of economic, technological and health services has been analysed. In particular, issues such as patient diagnosis, treatment processes, digital transformation in health, economic analyses, ethical and legal dimensions are discussed. Methodology: The research was conducted with qualitative and quantitative analysis methods. Using SWOT analysis, the strengths, weaknesses, opportunities and threats of artificial intelligence were evaluated, and its effects on the health sector were measured with economic and statistical models. Results: It was found that the strengths of artificial intelligence in the health sector have increased significantly over the years (from 50% to 90%), while the weaknesses have decreased (from 70% to 40%). With AI-supported diagnostic systems, errors have decreased, accuracy rates have increased, costs have decreased and access to healthcare services has become easier. Conclusion: Artificial intelligence has revolutionised the healthcare industry, accelerated diagnostic processes and improved patient care. However, issues such as data security, ethical regulations, and integration of AI into healthcare decisions are still an important topic of debate. Regulations to ensure the safe and ethical use of artificial intelligence stand out as a critical need.


  • Open Access

    Energy Absorption of a Novel Lattice Structure‐Filled Multicell Thin‐Walled Tubes Under Axial and Oblique Loadings

    by Gazi Basar Kocabas, Senai Yalcinkaya, Erhan Cetin, Yusuf Sahin

    Multicell design and lattice structure as filling material are two effective methods for enhancing the energy absorption performance of thin‐walled tubes. This study combines these two approaches to present a multicell tube with a novel lattice structure and investigates the energy absorption performances of these hybrid multicell tubes under axial (0°) and oblique (10°, 20°, and 30°) impact loading conditions. As filling structure, β‐Ti 3 Au lattice geometry with varying lattice strut diameters and the number of lattice unit cells are used, while the single and multicell thin‐walled tubes with different tube thicknesses are employed as main absorbing element. In this context, the effects of numbers of lattice unit cells, lattice strut diameter, cell numbers of the tube, and tube thickness on energy absorption performance of hybrid tubes are examined using validated nonlinear finite element models. This investigation unveils that the synergistic interplay between the multicell tubes and lattice structure during deformation significantly elevates the energy absorption performance of the hybrid structure. Notably, the findings demonstrate that multicell hybrid tubes exhibit a remarkable capacity to absorb up to 30.36% more impact energy compared to the aggregate absorption of individual components in hybrid tubes.


  • Open Access

    THE RELATIONSHIP BETWEEN MODERN DESIGN PRINCIPLES AND EMOTIONAL COMMUNICATION

    by Ozan Düz, Ozan Karabaş, Senai Yalçinkaya, Zeynep Yaman

    Aim: The aim of the study is to examine the effects of modern design principles on emotional communication and to understand the relationship between these two fields. Design is an important way for people to interact with products and their environment, and integrating emotional effects into design enhances the user experience. Scope: The research will be conducted in different design fields (graphic design, industrial design, interior design, etc.), and the effects of design on emotional communication will be examined. By including the perspectives of designers and users, the emotional effects of modern design principles are comprehensively evaluated. Methodology: Methodologies such as literature review, observation, and questionnaires were used to conduct the study. Different design examples were examined, designers and users were interviewed, and the effects of design on emotional communication were evaluated. Results: The results show that modern design principles positively impact emotional communication. Well-designed products and environments can cause positive emotional responses in users, increasing the preference for the product or environment. It was also observed that colors, forms, and material choices are important in determining emotional effects. Conclusion: The study concluded that modern design principles impact emotional communication. Considering emotional effects and aesthetic and functional design values enriches the user experience. Therefore, the most important conclusion is that design professionals and industrial designers should focus on integrating emotional communication into design processes.