Nur Zen
Nur Zen has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Hanny Vistanty
6 shared publicationsAris Mukimin
4 shared publicationsAgus Purwanto
Center of industrial pollution prevention technology
3 shared publicationsKukuh Aryo Wicaksono
Center of industrial pollution prevention technology
3 shared publications- Rustiana Yuliasni
Institute of Natural Materials Technology, Dresden University of Technology, 01069 Dresden, Germany
3 shared publications - Aris Mukimin
Center of Industrial Pollution Prevention Technology, Semarang - Indonesia
2 shared publications
Latest Publications
- Open Access
- 21 May 2020
- Published by Center of Industrial Pollution Prevention Technology in Jurnal Riset Teknologi Pencegahan Pencemaran Industri
- Vol. 11 (1) , 19-26
Evaluating the Performance of Three Chambers Microbial Salinity Cell (MSC) Subjected to Different Substrate Concentrations to Accomplish Simultaneous Organic and Salt Removal in the Wastewater
This study aimed to identify the effect of substrate concentration on the performance of A Three chambers Microbial Salinity Cell (a three chambers MSC). In this study, 3 three chambers MSC was made of plexy glass with total volume of 200 ml. Alumunium wrapped with with platinum on vulcan carbon cloth were used as electrodes,with each working area 63 cm2. The results showed that a Three chambers Microbial Salinity Cell was able to generate electricity and at the same time removed salinity. The degree of electricity deneration and salinity removal were influenced by initial substrate concentration in the anode chamber. The higher substrate concentration, the better performance of MSC. The best performance of MSC achieved when COD was 2034 mg/L, resulted in maximum voltage of 0. 44 V, and maximum current density of 0.29 mA/m2. With % CE was 5.4%. The maximum conductivity increase in salinity chamber was from 11.2 µS/cm to 1027 µS/cm (salinity 0.57% ppt).
- 21 May 2020
- Published by Center of Industrial Pollution Prevention Technology in Jurnal Riset Teknologi Pencegahan Pencemaran Industri
- Vol. 11 (1) , 19-26
Open AccessEvaluating the Performance of Three Chambers Microbial Salinity Cell (MSC) Subjected to Different Substrate Concentrations to Accomplish Simultaneous Organic and Salt Removal in the Wastewater
This study aimed to identify the effect of substrate concentration on the performance of A Three chambers Microbial Salinity Cell (a three chambers MSC). In this study, 3 three chambers MSC was made of plexy glass with total volume of 200 ml. Alumunium wrapped with with platinum on vulcan carbon cloth were used as electrodes,with each working area 63 cm2. The results showed that a Three chambers Microbial Salinity Cell was able to generate electricity and at the same time removed salinity. The degree of electricity deneration and salinity removal were influenced by initial substrate concentration in the anode chamber. The higher substrate concentration, the better performance of MSC. The best performance of MSC achieved when COD was 2034 mg/L, resulted in maximum voltage of 0. 44 V, and maximum current density of 0.29 mA/m2. With % CE was 5.4%. The maximum conductivity increase in salinity chamber was from 11.2 µS/cm to 1027 µS/cm (salinity 0.57% ppt).
- Open Access
- 21 May 2020
- Published by Center of Industrial Pollution Prevention Technology in Jurnal Riset Teknologi Pencegahan Pencemaran Industri
- Vol. 11 (1) , 36-45
DOAS Calibration Technique for SO2 Emission Measurement Based on H2SO4 and Na2SO3 Reaction
The coal used as a primary fuel in an Indonesian power plant produces sulfur dioxide emission from its burning process. Several testing and monitoring methods developed, from laboratory analysis, CEMs based instrument, and absorption spectroscopy method developed for this purpose. Differential Optical Absorption Spectroscopy (DOAS) method based on Lambert-Beer law used as emission quantification. DOAS instrumentation developed in this research to measure sulfur dioxide as one of the emission parameters. Sulfur dioxide generated from the reaction between the sulfuric acid and dilute sodium sulfite. CCD spectrometer used to measure sulfur dioxide spectrum intensity at 260 to 350 nm absorption cross-section. There is a high correlation between sulfur dioxide gas produced by that reaction to spectrum intensity, with coefficient determination (r2) 0.9783, 0.9822, 0.9866, 0.9928 or coefficient correlation (r) 0.989, 0.991, 0.993, and 0.996 from lowest range concentration to highest range concentration. Precision analysis from gas calibration standard using Horwitz ratio indicates instrument setup precise enough with 0.504 Horwitz ratio, according to its acceptable range. The suspended particulate matter may interfere with UV penetration into CCD detector in emission simulation test using gasoline generator exhaust that causes 2.5 times deviation error between typical 800 ppm concentrated sulfur dioxide from chemical reaction and gasoline generator exhaust.
- 21 May 2020
- Published by Center of Industrial Pollution Prevention Technology in Jurnal Riset Teknologi Pencegahan Pencemaran Industri
- Vol. 11 (1) , 36-45
Open AccessDOAS Calibration Technique for SO2 Emission Measurement Based on H2SO4 and Na2SO3 Reaction
The coal used as a primary fuel in an Indonesian power plant produces sulfur dioxide emission from its burning process. Several testing and monitoring methods developed, from laboratory analysis, CEMs based instrument, and absorption spectroscopy method developed for this purpose. Differential Optical Absorption Spectroscopy (DOAS) method based on Lambert-Beer law used as emission quantification. DOAS instrumentation developed in this research to measure sulfur dioxide as one of the emission parameters. Sulfur dioxide generated from the reaction between the sulfuric acid and dilute sodium sulfite. CCD spectrometer used to measure sulfur dioxide spectrum intensity at 260 to 350 nm absorption cross-section. There is a high correlation between sulfur dioxide gas produced by that reaction to spectrum intensity, with coefficient determination (r2) 0.9783, 0.9822, 0.9866, 0.9928 or coefficient correlation (r) 0.989, 0.991, 0.993, and 0.996 from lowest range concentration to highest range concentration. Precision analysis from gas calibration standard using Horwitz ratio indicates instrument setup precise enough with 0.504 Horwitz ratio, according to its acceptable range. The suspended particulate matter may interfere with UV penetration into CCD detector in emission simulation test using gasoline generator exhaust that causes 2.5 times deviation error between typical 800 ppm concentrated sulfur dioxide from chemical reaction and gasoline generator exhaust.
- Open Access
- 9 April 2019
- Published by Universitas Gadjah Mada in Indonesian Journal of Chemistry
- Vol. 19 (2) , 413-421
Synthesis of Graphite Porous Electrode Based on Coconut Shell as a Potential Cathode in Bioelectrosyntesis Cell
Electrodes, as well as microorganisms, are key materials for the development of bioelectrosynthesis cell reactor. Materials used as electrodes should be inert, crystalline in structure with high surface area and porous morphology, enhancing their electroactive and adsorptive properties. Carbon material derived from coconut shell was modified by simultaneous sintering-activation methods, FeCl3 and ZnCl2 were supplemented at temperature 900 °C at the non-atmospheric condition. The modified carbon was then molded with polyvinyl alcohol as a binder and the temperature was maintained at 80 °C and 10 ton of pressure. Molded carbon was then installed in bioelectrosynthesis cell with a working volume of 200 mL, as a cathode. XRD, BET, and SEM measurements showed the transformation of carbon surface from amorphous into the crystalline, increased surface area (11 times higher) and higher porosity (up to 500 nm). This cathode modification was able to increase current density up to 4 times and reduce CO2 into butyrate, 250 mg/L, in bioelectrosynthesis cell.
- 9 April 2019
- Published by Universitas Gadjah Mada in Indonesian Journal of Chemistry
- Vol. 19 (2) , 413-421
Open AccessSynthesis of Graphite Porous Electrode Based on Coconut Shell as a Potential Cathode in Bioelectrosyntesis Cell
Electrodes, as well as microorganisms, are key materials for the development of bioelectrosynthesis cell reactor. Materials used as electrodes should be inert, crystalline in structure with high surface area and porous morphology, enhancing their electroactive and adsorptive properties. Carbon material derived from coconut shell was modified by simultaneous sintering-activation methods, FeCl3 and ZnCl2 were supplemented at temperature 900 °C at the non-atmospheric condition. The modified carbon was then molded with polyvinyl alcohol as a binder and the temperature was maintained at 80 °C and 10 ton of pressure. Molded carbon was then installed in bioelectrosynthesis cell with a working volume of 200 mL, as a cathode. XRD, BET, and SEM measurements showed the transformation of carbon surface from amorphous into the crystalline, increased surface area (11 times higher) and higher porosity (up to 500 nm). This cathode modification was able to increase current density up to 4 times and reduce CO2 into butyrate, 250 mg/L, in bioelectrosynthesis cell.
- Open Access
- 26 November 2018
- Published by Center of Industrial Pollution Prevention Technology in Jurnal Riset Teknologi Pencegahan Pencemaran Industri
- Vol. 9 (2) , 11-20
IMPLEMENTATION OF ELECTROCATALYTIC REACTOR AS OXIDATION UNIT FOR RESIDUAL REAGENT WASTEWATER OF TESTING LABORATORY
The remaining reagent from the sample analysis process become a significant source of hazardous waste of laboratory tasting activities. Methylene blue, phenol and oil are pollutants common in the remaining reagent waste. The electrocatalytic reactor is effective oxidation units for these organic pollutants. The reactor was made for a 50 L capacity with cylindrical metal oxide as the anode. The three anode which 6 cm in diameter and 50 cm in length were paired stainless cathode with the distance of 2.5 cm. The reactor was also equipped with a stirrer that is connected to the motor so that the mass transfer and oxidizing agents is more effective. The reactor application was carried out by feeding the remaining reagent waste into the electrocatalytic unit and giving DC potential 5 Volt. Each COD content for reagent waste of detergent: 2864 mg/L, phenol: 838 mg/L and oil: 708 mg/L. The reactor has reduced COD to 2157 mg/L (detergent), 399 mg/L (phenol) and 506 mg/L (oil) for 120 minutes. The high COD content in residual is caused by solvent (chloroform or hexane) that used at extraction step in determining the process of a sample. This compound is tough to oxidize into CO2 by OH radical or hypochlorite acid formed at the anode during the electrolysis process
- 26 November 2018
- Published by Center of Industrial Pollution Prevention Technology in Jurnal Riset Teknologi Pencegahan Pencemaran Industri
- Vol. 9 (2) , 11-20
Open AccessIMPLEMENTATION OF ELECTROCATALYTIC REACTOR AS OXIDATION UNIT FOR RESIDUAL REAGENT WASTEWATER OF TESTING LABORATORY
The remaining reagent from the sample analysis process become a significant source of hazardous waste of laboratory tasting activities. Methylene blue, phenol and oil are pollutants common in the remaining reagent waste. The electrocatalytic reactor is effective oxidation units for these organic pollutants. The reactor was made for a 50 L capacity with cylindrical metal oxide as the anode. The three anode which 6 cm in diameter and 50 cm in length were paired stainless cathode with the distance of 2.5 cm. The reactor was also equipped with a stirrer that is connected to the motor so that the mass transfer and oxidizing agents is more effective. The reactor application was carried out by feeding the remaining reagent waste into the electrocatalytic unit and giving DC potential 5 Volt. Each COD content for reagent waste of detergent: 2864 mg/L, phenol: 838 mg/L and oil: 708 mg/L. The reactor has reduced COD to 2157 mg/L (detergent), 399 mg/L (phenol) and 506 mg/L (oil) for 120 minutes. The high COD content in residual is caused by solvent (chloroform or hexane) that used at extraction step in determining the process of a sample. This compound is tough to oxidize into CO2 by OH radical or hypochlorite acid formed at the anode during the electrolysis process
- 1 February 2018
- Published by Elsevier in Journal of Water Process Engineering
- Vol. 21, 77-83
Performance of bioequalization-electrocatalytic integrated method for pollutants removal of hand-drawn batik wastewater
- 1 February 2018
- Published by Elsevier in Journal of Water Process Engineering
- Vol. 21, 77-83
Performance of bioequalization-electrocatalytic integrated method for pollutants removal of hand-drawn batik wastewater
- 1 October 2017
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 5 (5) , 5222-5232
Application of a full-scale electrocatalytic reactor as real batik printing wastewater treatment by indirect oxidation process
- 1 October 2017
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 5 (5) , 5222-5232
Application of a full-scale electrocatalytic reactor as real batik printing wastewater treatment by indirect oxidation process
- 1 January 2015
- Published by Elsevier in Chemical Engineering Journal
- Vol. 259, 430-437
Oxidation of textile wastewater using cylinder Ti/β-PbO2 electrode in electrocatalytic tube reactor
- 1 January 2015
- Published by Elsevier in Chemical Engineering Journal
- Vol. 259, 430-437
Oxidation of textile wastewater using cylinder Ti/β-PbO2 electrode in electrocatalytic tube reactor