MCMiguel de Brito Costa

Miguel de Brito Costa

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Miguel de Brito Costa has a total of 54 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Evaluating the Radiological and Waste-Classification Cost-benefit of Reduced Activation in Steels for Nuclear Fusion

    by Thomas Davis, Emily R. Lewis, Guy Anderton, Mark D. Anderton, Jacobo Zegri, M.B. Costa, Richard Kembleton, Jan W. Coenen

    Reduced Activation Ferritic–Martensitic (RAFM) steels, like EUROFER, are proposed for fusion breeder blankets on the premise that reduced activation lowers radiological hazard and simplifies waste management. This study tests this hypothesis by comparing EUROFER and Grade 91 steel with FISPACT-II activation modelling under representative blanket conditions, with structural performance assumed equivalent. EUROFER reduces Ni-63, Nb-94 and Mo-derived isotopes but both steels are dominated by C-14 and Mn-53 at long cooling times. At 100 years after shutdown both steels remain ILW under the UK and European frameworks assessed, implying no change in disposal route; benefits during operation and decommissioning were not assessed. C-14, which dominates long-term geological hazard, is unaffected by alloy design. The results demonstrate that RAFM steels provide continuous benefits through reductions in activity and radiological dose but do not demonstrate corresponding threshold benefits, such as changes in waste classification, disposal pathway or repository requirements, under the conditions assessed. The reductions in activation inventory do not translate into proportional reductions in lifecycle waste-management burden. When considered within an ALARA framework and balanced against procurement, qualification burden and supply-chain maturity, the value generated through reduced activation is limited for near-term devices. Under the assumptions considered, the radiological benefits of EUROFER alone are insufficient to justify the current procurement premiums and qualification effort. The results indicate that the principal limitation of RAFM steels is value generation rather than activation performance, although this conclusion may change as procurement costs, qualification maturity and regulatory frameworks evolve.

  • Open Access

    From perfection to pragmatism: a materials- and components-led qualification strategy for fusion power plants

    by Jan W. Coenen, Richard Kembleton, Thomas Davis, Jacobo Zegri, Samuel Aaron Lazerson, Egor Vezhlev, Liang Gao, M.B. Costa, Christian Linsmeier, Frederick Bordry

    Fusion power is transitioning from a primarily physics-driven challenge to one dominated by materials and component qualification. Many sub-components have performed acceptably in relevant environments, yet deployment timelines keep slipping because qualification is treated as a prerequisite for construction rather than a process that matures alongside operation and is validated through it. This paper argues for a structuredpragmatism approach, in which a first-of-a-kind (FOAK) fusion power plant designed from the outset as a materials and components substantiation platform. Drawing on system-level assumptions for a European gigawatt-class stellarator power plant such as GIGA, the paper shows that credible,licensable baselines already exist. The remaining uncertainties are not primarily about material feasibility but about quantified performance in the integrated system. They hinge on practical, system-level constraints, manufacturing route, joining technique, quality assurance, local radiation environment, lifetime requirements, tritium control, inspection strategy, replacement schedule, and waste route, that determine whether a material choice is deployable in a physical reactor. The paper proposes a qualification framework for early fusion plants operating under bounded uncertainty, combining bounded operating envelopes, staged commissioning, embedded materials surveillance, neutronics-informed evidence ranking, manufacturing traceability, and risk-informed licensing into a single materials-intelligence substantiation loop. Its central conclusion is that fusion materials qualification cannot be completed before the first power plant exists; it must be completed through that plant’s controlled, evidence-generating operation

  • Alloy Development of Ductile and Strain‐Hardening Fe–Ni‐Based Metallic Glass Composite

    by Miguel B. Costa, Kenneth S. Vecchio, Henry Kozachkov, Douglas C. Hofmann

    Metallic‐glass composites (MGCs) combine the strength and hardness of MGs with the ductility, toughness, and fatigue resistance of crystalline materials. This study focuses on developing Fe‐based in situ dendritic MGCs in the (Fe, Ni) – Mo – B – C system with pseudo‐equilibrium phase distributions. The alloy design strategy involves tailoring the liquid compositional partitioning to allow the formation of a MG phase with the quench rates employed and to control the composition of the primary crystalline phase. The alloy's Fe – Ni ratio is fixed to tailor the elastic “softness” of the dendrites, and the B content is varied to achieve different microstructural length scales and volume fractions of crystalline and glassy phases. Splat quenching is used to perform alloy development and create thin sheets of the MGCs. These were then characterized by X‐ray diffraction, microhardness, and ribbon tensile testing. Compositions with ≥3.5 at.% B formed MGCs with crystalline dendrites and an amorphous phase, showing improved ductility and achieving strain hardening in the thin sheets.


  • Upcycling Titanium‐Based Bulk Metallic Glass Scrap Feedstock Through Compositional Steering

    by Douglas C. Hofmann, Miguel de Brito Costa, Punnathat Bordeenithikasem, Melanie A. Buziak, Thomas Freeman, Anthony Botros

    Bulk metallic glasses (BMGs) are an emerging commercial material with applications in consumer electronics, fasteners, watches, and precision gears, among other uses. Mass‐production of hardware using BMGs requires the production of feedstock material using conventional foundry techniques, normally comprising rods, thin sheets, and powder. Due to the unique amorphous nature and highly designed compositions of BMGs, recycling and upcycling waste products are challenging because the properties of BMGs are highly dependent on their chemical composition and impurity content. In this work, an off‐composition, scrap titanium‐based BMG feedstock material is upcycled into usable material through the novel use of a correction ingot to steer the composition into either a better glass‐forming alloy or an alloy that exhibits improved mechanical performance. In one example, the feedstock, initially with exceptionally poor mechanical properties and low glass‐forming‐ability, can be compositionally steered into a 3.5 mm thick BMG by mixing it with as little as 25% by mass of a designed alloy.


  • Open Access

    Pd- and Zr-based bulk metallic glasses for jewellery applications: Scratch, wear and tarnish behaviour

    by Owain S. Houghton, Lisa-Y. Schmitt, Ulrich E. Klotz, Miguel B. Costa, A. Lindsay Greer


  • Open Access

    Reinterpretation of Report of Tetrataenite in Bulk Alloy Castings

    by Owain S. Houghton, James C. Loudon, Alison C. Twitchett‐Harrison, Nikolaos T. Panagiotopoulos, Giulio I. Lampronti, Miguel B. Costa, Richard J. Harrison, A. Lindsay Greer

    After the publication of “Direct formation of hard‐magnetic tetrataenite in bulk alloy castings” Ivanov et al., Advanced Science 10 (2022) 2204315, the authors identified a potential misinterpretation of the experimental data. Further work confirms that the original conclusions cannot be supported, and accordingly the paper is retracted. X‐ray diffraction shows the presence of (Fe,Ni)3P, giving additional Bragg peaks that were previously attributed to tetrataenite. Extra Bragg reflections observed in transmission electron diffraction, and earlier considered to be superlattice reflections from tetrataenite, instead result from oxidation of the sample surface during preparation. Measurements of magnetic hysteresis show no regions of high coercivity of the kind expected when tetrataenite is present. It is concluded that as‐cast bulk samples of Fe‐Ni‐P‐(C) show no evidence of tetrataenite on any length scale. Nevertheless, the addition of phosphorus should remain of interest in ongoing efforts to manufacture tetrataenite.


  • Effect of thermal history on performance of bulk metallic glass spacecraft components

    by Punnathat Bordeenithikasem, Richard Otis, Miguel B. Costa, Douglas C. Hofmann, R. Peter Dillon


  • Open Access

    Hierarchical Surface Pattern on Ni‐Free Ti‐Based Bulk Metallic Glass to Control Cell Interactions

    by Fei‐Fan Cai, Andreu Blanquer, Miguel B. Costa, Lukas Schweiger, Baran Sarac, A. Lindsay Greer, Jan Schroers, Christian Teichert, Carme Nogués, Florian Spieckermann, et al.

    Ni‐free Ti‐based bulk metallic glasses (BMGs) are exciting materials for biomedical applications because of their outstanding biocompatibility and advantageous mechanical properties. The glassy nature of BMGs allows them to be shaped and patterned via thermoplastic forming (TPF). This work demonstrates the versatility of the TPF technique to create micro‐ and nano‐patterns and hierarchical structures on Ti40Zr10Cu34Pd14Sn2 BMG. Particularly, a hierarchical structure fabricated by a two‐step TPF process integrates 400 nm hexagonal close‐packed protrusions on 2.5 µm square protuberances while preserving the advantageous mechanical properties from the as‐cast material state. The correlations between thermal history, structure, and mechanical properties are explored. Regarding biocompatibility, Ti40Zr10Cu34Pd14Sn2 BMGs with four surface topographies (flat, micro‐patterned, nano‐patterned, and hierarchical‐structured surfaces) are investigated using Saos‐2 cell lines. Alamar Blue assay and live/dead analysis show that all tested surfaces have good cell proliferation and viability. Patterned surfaces are observed to promote the formation of longer filopodia on the edge of the cytoskeleton, leading to star‐shaped and dendritic cell morphologies compared with the flat surface. In addition to potential implant applications, TPF‐patterned Ti‐BMGs enable a high level of order and design flexibility on the surface topography, expanding the available toolbox for studying cell behavior on rigid and ordered surfaces.