Lingbo Zhu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Lingbo Zhu has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Jianfei Tong
Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049, China
6 shared publications - Yiping Lu
Department of Mechanical and Power Engineering, Harbin University of Science and Technology, Harbin 150080, China
6 shared publications - Youlian Lu
Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049, China
5 shared publications - Tianjiao Liang
Institute of High Energy Physics, Chinese Academy of Sciences (CAS), Beijing, China
4 shared publications - Songlin Wang
Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049, China
3 shared publications - Chaoju Yu
Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049, China
2 shared publications
Latest Publications
- Open Access
Comparative Research on Ventilation Characteristics of Scattering and Sample Room from Chinese Spallation Neutron Source
Ventilation design of the scattering room and sample room in the Chinese Spallation Neutron Source (CSNS) is of great significance to maintain good indoor air quality and ensure the health of radiation workers. Based on the computational fluid dynamics (CFD) theory, the three-dimensional models of the scattering and sample rooms were established and fourteen layout schemes were simulated. Subsequently, the best schemes were selected among three typical layout schemes. On this basis, the paper presents research about the influence of changing the height of the outlet on the ventilation quality. The results show that the trend of numerical simulation is consistent with experimental data, which verifies the reliability of the numerical method. The change of the exhaust port position has an apparent influence on indoor ventilation, which reduces the air age by 4–27%. When the position of the outlet descends 0.5 m, the air age decreases by 2–11%, and this study provides guidance and suggestions for the design of the scattering and sample rooms.
Open AccessComparative Research on Ventilation Characteristics of Scattering and Sample Room from Chinese Spallation Neutron Source
Ventilation design of the scattering room and sample room in the Chinese Spallation Neutron Source (CSNS) is of great significance to maintain good indoor air quality and ensure the health of radiation workers. Based on the computational fluid dynamics (CFD) theory, the three-dimensional models of the scattering and sample rooms were established and fourteen layout schemes were simulated. Subsequently, the best schemes were selected among three typical layout schemes. On this basis, the paper presents research about the influence of changing the height of the outlet on the ventilation quality. The results show that the trend of numerical simulation is consistent with experimental data, which verifies the reliability of the numerical method. The change of the exhaust port position has an apparent influence on indoor ventilation, which reduces the air age by 4–27%. When the position of the outlet descends 0.5 m, the air age decreases by 2–11%, and this study provides guidance and suggestions for the design of the scattering and sample rooms.
- Open Access
Study on Convective Heat Transfer Characteristics of Supercritical Liquid Hydrogen in a U-Type Tube inside a Moderator
The flow and heat transfer characteristics of supercritical fluid in a U-tube have an important influence on the safe operation of a moderator, and the variation of gravity direction is suitable for special working conditions of the moderator. In this study, the three-dimensional turbulence flow and heat transfers of supercritical liquid hydrogen in a U-tube were investigated at an Re number ranging from 16,425 to 54,750 under constant heat flux (q = 80 kW/m2). The total length of the U-tube was 1725 mm, which had an entrance length L/D of 23, with the inner diameter and wall thickness of D × δ = 10 × 2 mm. The finite volume method was adopted, and the grid independence was verified by the grid convergence index (GCI). The calculation results of three turbulence models (SST k-w, RNG k-ε, Standard k-ε) were compared with the corresponding experimental data to obtain the turbulence model with the smallest error. The convective heat transfer characteristics with different values of heat flux (q = 30 kW/m2~100 kW/m2), mass flow (G = 3 g/s~10 g/s), and gravity (gx, gy, gz) were compared. Meanwhile, the heat transfer characteristics of supercritical liquid and conventional liquid hydrogen were compared. The results show that Nu increased from 5 g/s to 10 g/s by 56.6%, and mass flow rate had a greater impact on the variation of Nu; when gravity direction was consistent with the flow direction of liquid hydrogen (gx direction), the Nu number inside the channel was 4.21% and 5.56% higher than that in gy and gz direction, respectively. Supercritical liquid hydrogen has a stronger heat transfer ability than conventional liquid hydrogen, of which the Nu number is 16.7% higher. This study can provide useful guidance for the design of flow and heat transfer of supercritical liquid hydrogen in a U-tube and its application in moderators. Furthermore, it provides reference technical values for thermal safety and thermal management of the target station to ensure its safe and stable operation.
Open AccessStudy on Convective Heat Transfer Characteristics of Supercritical Liquid Hydrogen in a U-Type Tube inside a Moderator
The flow and heat transfer characteristics of supercritical fluid in a U-tube have an important influence on the safe operation of a moderator, and the variation of gravity direction is suitable for special working conditions of the moderator. In this study, the three-dimensional turbulence flow and heat transfers of supercritical liquid hydrogen in a U-tube were investigated at an Re number ranging from 16,425 to 54,750 under constant heat flux (q = 80 kW/m2). The total length of the U-tube was 1725 mm, which had an entrance length L/D of 23, with the inner diameter and wall thickness of D × δ = 10 × 2 mm. The finite volume method was adopted, and the grid independence was verified by the grid convergence index (GCI). The calculation results of three turbulence models (SST k-w, RNG k-ε, Standard k-ε) were compared with the corresponding experimental data to obtain the turbulence model with the smallest error. The convective heat transfer characteristics with different values of heat flux (q = 30 kW/m2~100 kW/m2), mass flow (G = 3 g/s~10 g/s), and gravity (gx, gy, gz) were compared. Meanwhile, the heat transfer characteristics of supercritical liquid and conventional liquid hydrogen were compared. The results show that Nu increased from 5 g/s to 10 g/s by 56.6%, and mass flow rate had a greater impact on the variation of Nu; when gravity direction was consistent with the flow direction of liquid hydrogen (gx direction), the Nu number inside the channel was 4.21% and 5.56% higher than that in gy and gz direction, respectively. Supercritical liquid hydrogen has a stronger heat transfer ability than conventional liquid hydrogen, of which the Nu number is 16.7% higher. This study can provide useful guidance for the design of flow and heat transfer of supercritical liquid hydrogen in a U-tube and its application in moderators. Furthermore, it provides reference technical values for thermal safety and thermal management of the target station to ensure its safe and stable operation.
- Open Access
Study of Flow and Heat Transfer for the Supercritical Hydrogen in Spallation-Type Cylindrical Neutron Moderator
Pipe height in cylindrical neutron moderator is an important factor to flow pattern, temperature distribution and even the neutron characters. In this paper, the steady-state thermal analysis of cold neutron moderator is carrying out with different heights, conjugated heat transfer method and one-way coupled with a neutron transfer software. The different pipe heights, which is the jet-to-surface distances (H/D = 0.5~6), were compared using a 2D moderator model. The results show that vortex size and velocity gradient from container wall to vortex center vary with H/D, the center of recirculation zone nearly remain constant, and heat transfer effect is weakened on the target bottom surface. With H/D increasing, the velocity at bottom target surface is progressively decreased, and cooling effect is poor, leading to the rise in temperature. The optimal range cooling performance is (H/D) = 0.5~1 at Re = 1.7 × 105, and the enhancement of beam power further strengthens the thermal deposition difference between container and liquid hydrogen. The results can be applied to moderator component design and optimization in the future spallation neutron source.
Open AccessStudy of Flow and Heat Transfer for the Supercritical Hydrogen in Spallation-Type Cylindrical Neutron Moderator
Pipe height in cylindrical neutron moderator is an important factor to flow pattern, temperature distribution and even the neutron characters. In this paper, the steady-state thermal analysis of cold neutron moderator is carrying out with different heights, conjugated heat transfer method and one-way coupled with a neutron transfer software. The different pipe heights, which is the jet-to-surface distances (H/D = 0.5~6), were compared using a 2D moderator model. The results show that vortex size and velocity gradient from container wall to vortex center vary with H/D, the center of recirculation zone nearly remain constant, and heat transfer effect is weakened on the target bottom surface. With H/D increasing, the velocity at bottom target surface is progressively decreased, and cooling effect is poor, leading to the rise in temperature. The optimal range cooling performance is (H/D) = 0.5~1 at Re = 1.7 × 105, and the enhancement of beam power further strengthens the thermal deposition difference between container and liquid hydrogen. The results can be applied to moderator component design and optimization in the future spallation neutron source.
- Open Access
Sensitivity Analysis of Influencing Factors of Supercritical Methane Flow and Heat Transfer in a U-Tube
Due to the existence of a Dean vortex in a U-tube, the flow and heat transfer process of supercritical methane is complex, and its thermophysical property are greatly influenced by different factors. Based on computational fluid dynamics theory, the numerical simulation of the turbulent flow and heat transfer characteristics of supercritical methane in a U-tube with an inner diameter of 10 mm and a radius of curvature of 27 mm carried out by using the finite volume method. On the basis of verifying the reliability of the model, the influences of inlet mass flux (G), heat flux on the tube wall boundary (q), pressure on the outlet (P), and gravity acceleration factors (g) on heat transfer characteristics were analyzed. The calculation results show that the sensitivity of the effects of G, q, P, and g on the heat transfer coefficient is, from large to small, in the order of P, G, g, and q. Compared with a horizontal straight tube, a U-tube can significantly improve heat transfer in the elbow part, but the presence of the elbow reduces heat transfer in the subsequent straight pipe section. The research in this paper has significance as a reference for the construction of the LNG gasification process.
Open AccessSensitivity Analysis of Influencing Factors of Supercritical Methane Flow and Heat Transfer in a U-Tube
Due to the existence of a Dean vortex in a U-tube, the flow and heat transfer process of supercritical methane is complex, and its thermophysical property are greatly influenced by different factors. Based on computational fluid dynamics theory, the numerical simulation of the turbulent flow and heat transfer characteristics of supercritical methane in a U-tube with an inner diameter of 10 mm and a radius of curvature of 27 mm carried out by using the finite volume method. On the basis of verifying the reliability of the model, the influences of inlet mass flux (G), heat flux on the tube wall boundary (q), pressure on the outlet (P), and gravity acceleration factors (g) on heat transfer characteristics were analyzed. The calculation results show that the sensitivity of the effects of G, q, P, and g on the heat transfer coefficient is, from large to small, in the order of P, G, g, and q. Compared with a horizontal straight tube, a U-tube can significantly improve heat transfer in the elbow part, but the presence of the elbow reduces heat transfer in the subsequent straight pipe section. The research in this paper has significance as a reference for the construction of the LNG gasification process.
- Open Access
Heat Transfer Analysis in Supercritical Hydrogen of Decoupled Poisoned Hydrogen Moderator with Non-Uniform Heat Source of Chinese Spallation Neutron Source
The flow field distribution and thermal properties of supercritical hydrogen are crucial factors affecting the quality of neutrons output from spallation neutron source, which may contribute to the optimization design of the moderator. Several sensitivity studies on affecting heat transfer characteristics of liquid hydrogen inside a moderator were executed, and a choice was made to use a computational fluid dynamics method for numerical simulation. The sensitivity degree of factors affecting the heat transfer characteristics of liquid hydrogen are in sequence of inlet mass flow, beam power and operating pressure. Especially when the beam power is 500 kW (the temperature range of liquid hydrogen is about 20~30 K); where the effect of mass flow rate is remarkable, the cooling effect is best in the range of 60~90 g/s × 394 mm2. Meanwhile, the maximum temperature of liquid hydrogen is close to the bottom recirculation zone due to the influence of the flow field and the heat deposition distribution of the poisoned plate. The effect of variable pressure on the temperature of liquid hydrogen is not significant, whereas the sudden rise of wall temperature is observed near the large specific heat region of 15 bar.
Open AccessHeat Transfer Analysis in Supercritical Hydrogen of Decoupled Poisoned Hydrogen Moderator with Non-Uniform Heat Source of Chinese Spallation Neutron Source
The flow field distribution and thermal properties of supercritical hydrogen are crucial factors affecting the quality of neutrons output from spallation neutron source, which may contribute to the optimization design of the moderator. Several sensitivity studies on affecting heat transfer characteristics of liquid hydrogen inside a moderator were executed, and a choice was made to use a computational fluid dynamics method for numerical simulation. The sensitivity degree of factors affecting the heat transfer characteristics of liquid hydrogen are in sequence of inlet mass flow, beam power and operating pressure. Especially when the beam power is 500 kW (the temperature range of liquid hydrogen is about 20~30 K); where the effect of mass flow rate is remarkable, the cooling effect is best in the range of 60~90 g/s × 394 mm2. Meanwhile, the maximum temperature of liquid hydrogen is close to the bottom recirculation zone due to the influence of the flow field and the heat deposition distribution of the poisoned plate. The effect of variable pressure on the temperature of liquid hydrogen is not significant, whereas the sudden rise of wall temperature is observed near the large specific heat region of 15 bar.
- Open Access
Study on the Convective Heat Transfer and Fluid Flow of Mini-Channel with High Aspect Ratio of Neutron Production Target
In order to provide a theoretical basis for the thermal design of the neutron production target, flow and heat transfer characteristics are studied by using numerical simulations and experiments. A rectangular mini-channel experimental model consistent with the geometric shape of the heat dissipation structure of neutron production target was established, in which the aspect ratio and gap thickness of the test channel were 53.8:1 and 1.3 mm, respectively. The experimental results indicate that the critical Re of the mini-channel is between 3500 and 4000, and when Re reaches 21,000, Nu can reach 160. The simulation results are in good agreement with the experimental data, and the numerical simulation method can be used for the variable structure optimization design of the target in the later stage. The relationship between the flow pressure drop of the target mini-channel and the aspect ratio and Re is obtained by numerical simulation. The maximum deviation between the correlation and the experimental value is 6%.
Open AccessStudy on the Convective Heat Transfer and Fluid Flow of Mini-Channel with High Aspect Ratio of Neutron Production Target
In order to provide a theoretical basis for the thermal design of the neutron production target, flow and heat transfer characteristics are studied by using numerical simulations and experiments. A rectangular mini-channel experimental model consistent with the geometric shape of the heat dissipation structure of neutron production target was established, in which the aspect ratio and gap thickness of the test channel were 53.8:1 and 1.3 mm, respectively. The experimental results indicate that the critical Re of the mini-channel is between 3500 and 4000, and when Re reaches 21,000, Nu can reach 160. The simulation results are in good agreement with the experimental data, and the numerical simulation method can be used for the variable structure optimization design of the target in the later stage. The relationship between the flow pressure drop of the target mini-channel and the aspect ratio and Re is obtained by numerical simulation. The maximum deviation between the correlation and the experimental value is 6%.