Sein Oh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sein Oh has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Minkyu Je
Korea Advanced Institute of Science and Technology (KAIST)
8 shared publications - Sohmyung Ha
New York University Abu Dhabi
7 shared publications - Haidam Choi
Korea Advanced Institute of Science and Technology (KAIST)
3 shared publications - Yoontae Jung
School of Electronic Engineering, Kyung Hee University, Yongin, South Korea
3 shared publications - Gichan Yun
Korea Advanced Institute of Science and Technology (KAIST)
2 shared publications - Hyungil Chae
Department of Electrical Engineering, Konkuk University, Seoul, South Korea
2 shared publications
Latest Publications
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (10) , 1-14
A Bio-Impedance Readout IC With Phase-Locked Sampling for Real-Time Electrical Impedance Spectroscopy
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (10) , 1-14
A Bio-Impedance Readout IC With Phase-Locked Sampling for Real-Time Electrical Impedance Spectroscopy
- 17 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (11) , 1570-1574
A 2.0-mW 70.1-dB SNDR 7.8-MHz BW Continuous-Time Noise-Shaping SAR ADC Using Fully Parallelized Quantization
This brief presents a continuous-time (CT) noiseshaping SAR (NS-SAR) ADC using a fully parallelized quantization technique to overcome the sampling speed limitations of the conventional structures employing a duty-cycled integrator. The proposed ADC parallelizes the quantization and integration paths using two identical input stages, eliminating the dutycycling operation in the integrator. This approach mitigates the loop stability degradation caused by the limited timing slots for integration at higher sampling speeds while preserving the inherent anti-aliasing and noise-shaping properties. Furthermore, the ability to continuously track the input signal of the CT SAR operation removes the requirement for excess loop delay compensation circuits, relaxing constraints on maximizing the sampling speed. Fabricated in a 28-nm CMOS process, the prototype ADC achieves an SNDR of 70.1 dB with a power consumption of 2.0 mW at 500 MS/s, resulting in a Schreier figure of merit of 166.0 dB.
- 17 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (11) , 1570-1574
A 2.0-mW 70.1-dB SNDR 7.8-MHz BW Continuous-Time Noise-Shaping SAR ADC Using Fully Parallelized Quantization
This brief presents a continuous-time (CT) noiseshaping SAR (NS-SAR) ADC using a fully parallelized quantization technique to overcome the sampling speed limitations of the conventional structures employing a duty-cycled integrator. The proposed ADC parallelizes the quantization and integration paths using two identical input stages, eliminating the dutycycling operation in the integrator. This approach mitigates the loop stability degradation caused by the limited timing slots for integration at higher sampling speeds while preserving the inherent anti-aliasing and noise-shaping properties. Furthermore, the ability to continuously track the input signal of the CT SAR operation removes the requirement for excess loop delay compensation circuits, relaxing constraints on maximizing the sampling speed. Fabricated in a 28-nm CMOS process, the prototype ADC achieves an SNDR of 70.1 dB with a power consumption of 2.0 mW at 500 MS/s, resulting in a Schreier figure of merit of 166.0 dB.
- 8 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 19 (2) , 291-299
A Time-Domain Multi-Channel Resistive-Sensor Interface IC With High Energy Efficiency and Wide Input Range
This paper presents a 72-channel resistive-sensor interface integrated circuit (IC). The proposed IC consists of 8 sensor oscillator units and a reference clock generator. The sensor oscillator (S-OSC) units generate pulses with pulse widths dependent on the sensor input values, and the pulses are oversampled by the reference clock using frequency dividers. The time-domain signals are fed to the time-to-digital converters (TDCs) and converted to digital values. Each S-OSC unit is time-multiplexed to measure the resistance values from 9 sensors. Multiple phases from a highly energy-efficient phase-locked loop (PLL) are used for the TDCs, resulting in a signal-to-quantization-noise ratio (SQNR) that exceeds the intrinsic signal-to-noise ratio (SNR) of the sensor oscillators. This results in an effective number of bits (ENOB) of 9.3 bits at 310 pJ per channel. The maximum ENOB that can be achieved with a division ratio (N) of 256 is 14.1 bits and can be adjusted by changing N. Using this time-domain interface approach, the IC converts the sensor resistances directly into time, extending its measurement capabilities to 10 MΩ. The proposed IC, designed and fabricated in a 180-nm CMOS process with an active area of 0.015 mm2, consumes only 15.07 μW per channel, resulting in a channel-specific Walden figure of merit (FoM) of 0.48 pJ per conversion step. In addition, by tuning N, the IC achieves an outstanding Schreier FoM of 159.8 dB in high-resolution scenarios.
- 8 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 19 (2) , 291-299
A Time-Domain Multi-Channel Resistive-Sensor Interface IC With High Energy Efficiency and Wide Input Range
This paper presents a 72-channel resistive-sensor interface integrated circuit (IC). The proposed IC consists of 8 sensor oscillator units and a reference clock generator. The sensor oscillator (S-OSC) units generate pulses with pulse widths dependent on the sensor input values, and the pulses are oversampled by the reference clock using frequency dividers. The time-domain signals are fed to the time-to-digital converters (TDCs) and converted to digital values. Each S-OSC unit is time-multiplexed to measure the resistance values from 9 sensors. Multiple phases from a highly energy-efficient phase-locked loop (PLL) are used for the TDCs, resulting in a signal-to-quantization-noise ratio (SQNR) that exceeds the intrinsic signal-to-noise ratio (SNR) of the sensor oscillators. This results in an effective number of bits (ENOB) of 9.3 bits at 310 pJ per channel. The maximum ENOB that can be achieved with a division ratio (N) of 256 is 14.1 bits and can be adjusted by changing N. Using this time-domain interface approach, the IC converts the sensor resistances directly into time, extending its measurement capabilities to 10 MΩ. The proposed IC, designed and fabricated in a 180-nm CMOS process with an active area of 0.015 mm2, consumes only 15.07 μW per channel, resulting in a channel-specific Walden figure of merit (FoM) of 0.48 pJ per conversion step. In addition, by tuning N, the IC achieves an outstanding Schreier FoM of 159.8 dB in high-resolution scenarios.
- 17 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (11) , 3538-3548
A Bio-Impedance Readout IC With Complex-Domain Noise-Correlated Baseline Cancellation
This article presents a bio-impedance (bioZ) readout IC featuring a complex-domain noise-correlated baseline cancellation to overcome the limitation of the conventional baseline cancellation with the real-domain noise correlation. The proposed technique is especially beneficial in cases with significant phase shifts between the excitation current from the current generator (CG) and the input voltage signal produced across the bioZ, through which the CG current flows. This technique employs a tunable reference impedance (TRI) and adaptively adjusts it to match the bioZ in both magnitude and phase, thereby achieving a complex-domain correlation of CG noise. By flowing an identical CG current through both the TRI and bioZ, the noise voltages across the TRI and bioZ caused by the CG current become closely correlated with each other, even in the presence of substantial phase shifts, enabling effective CG noise removal after baseline subtraction. Furthermore, this work proposes a differential-difference current-balancing instrumentation amplifier (DD-CBIA) with quiet chopping for baseline subtraction, offering low power consumption, wide input range, and low input-dependent noise. Measurement results demonstrate significant enhancements in noise performance by a factor of 2.47 and 4.88 for the bioZs with phases of 30° and 60°, respectively, achieving a signal-to-noise ratio (SNR) of 101.5 dB and a figure of merit (FoM) of 150.0 dB. Validation through human-subject experiments using two-electrode configurations on the chest and wrist further supports the effectiveness of the proposed bioZ readout IC.
- 17 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (11) , 3538-3548
A Bio-Impedance Readout IC With Complex-Domain Noise-Correlated Baseline Cancellation
This article presents a bio-impedance (bioZ) readout IC featuring a complex-domain noise-correlated baseline cancellation to overcome the limitation of the conventional baseline cancellation with the real-domain noise correlation. The proposed technique is especially beneficial in cases with significant phase shifts between the excitation current from the current generator (CG) and the input voltage signal produced across the bioZ, through which the CG current flows. This technique employs a tunable reference impedance (TRI) and adaptively adjusts it to match the bioZ in both magnitude and phase, thereby achieving a complex-domain correlation of CG noise. By flowing an identical CG current through both the TRI and bioZ, the noise voltages across the TRI and bioZ caused by the CG current become closely correlated with each other, even in the presence of substantial phase shifts, enabling effective CG noise removal after baseline subtraction. Furthermore, this work proposes a differential-difference current-balancing instrumentation amplifier (DD-CBIA) with quiet chopping for baseline subtraction, offering low power consumption, wide input range, and low input-dependent noise. Measurement results demonstrate significant enhancements in noise performance by a factor of 2.47 and 4.88 for the bioZs with phases of 30° and 60°, respectively, achieving a signal-to-noise ratio (SNR) of 101.5 dB and a figure of merit (FoM) of 150.0 dB. Validation through human-subject experiments using two-electrode configurations on the chest and wrist further supports the effectiveness of the proposed bioZ readout IC.
- 23 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Magazine
- Vol. 16 (3) , 55-66
Process-Scalable and Low-Power Amplifiers: Progress and prospects in dynamic amplifier research
Amplifiers are critical components in many applications. They simply perform signal amplification, but real-world implementation must consider several challenges, such as finite BW, signal distortion, noise, stability, and so on. Solutions to these problems typically involve circuit techniques that lead to high power consumption. Therefore, numerous studies have been conducted to break the tradeoff between performance and power. Among the most promising candidates is the current-reuse structure [1] , [2] , [3] , [4] , [5] , [6] . Such amplifiers have continuously improved their power efficiency factor (PEF) performance year by year. However, there are essential limitations to consider. First, the supply voltage significantly decreases as the process node advances. This process scaling not only makes it challenging for amplifiers to achieve high gain but also significantly degrades linearity. Second, conventional amplifiers, meaning continuous-time (CT) amplifiers, operate with a static current. While better PEFs of CT amplifiers improve overall performance envelopes in many CT-domain applications, they exhibit clear limitations in discrete-time (DT)-domain or mixed-signal applications.
- 23 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Magazine
- Vol. 16 (3) , 55-66
Process-Scalable and Low-Power Amplifiers: Progress and prospects in dynamic amplifier research
Amplifiers are critical components in many applications. They simply perform signal amplification, but real-world implementation must consider several challenges, such as finite BW, signal distortion, noise, stability, and so on. Solutions to these problems typically involve circuit techniques that lead to high power consumption. Therefore, numerous studies have been conducted to break the tradeoff between performance and power. Among the most promising candidates is the current-reuse structure [1] , [2] , [3] , [4] , [5] , [6] . Such amplifiers have continuously improved their power efficiency factor (PEF) performance year by year. However, there are essential limitations to consider. First, the supply voltage significantly decreases as the process node advances. This process scaling not only makes it challenging for amplifiers to achieve high gain but also significantly degrades linearity. Second, conventional amplifiers, meaning continuous-time (CT) amplifiers, operate with a static current. While better PEFs of CT amplifiers improve overall performance envelopes in many CT-domain applications, they exhibit clear limitations in discrete-time (DT)-domain or mixed-signal applications.
- 26 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (4) , 1204-1215
A 187-dB FoMS Power-Efficient Second-Order Highpass ΔΣ Capacitance-to-Digital Converter
The escalating demand for high-resolution sensor interface systems, driven by the proliferation of the Internet of Things (IoT) and wearable smart devices, has led to the widespread use of capacitive sensing transducers. These transducers are valued for their low-noise and low-power characteristics, making them suitable for various applications, including environmental and biomedical sensing. However, designing a high-resolution capacitive sensor interface system while maintaining power efficiency remains challenging. This article proposes a high-resolution energy-efficient highpass (HP) $\Delta\Sigma$ capacitance-to-digital converter (CDC) architecture. The architecture incorporates a 2 ${\textrm{nd}}$ -order HP $\Delta\Sigma$ modulator ( $\Delta\Sigma$ M) and a continuous-time capacitance-to-voltage converter (CT CVC). The proposed CDC achieves an excellent capacitance resolution of 5.85 aF $_\textrm{rms}$ , with a power efficiency of 46 fJ/conversion-step and an FoM $_\textrm{S}$ of 187.4 dB. The HP $\Delta\Sigma$ M, designed with superior power efficiency, offers a promising solution for high-resolution capacitive sensor applications. Compared to state-of-the-art, the proposed CDC achieves more than 2 $\times$ FoM $_\textrm{S}$ improvement while maintaining competitive FoM $_\textrm{W}$ .
- 26 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (4) , 1204-1215
A 187-dB FoMS Power-Efficient Second-Order Highpass ΔΣ Capacitance-to-Digital Converter
The escalating demand for high-resolution sensor interface systems, driven by the proliferation of the Internet of Things (IoT) and wearable smart devices, has led to the widespread use of capacitive sensing transducers. These transducers are valued for their low-noise and low-power characteristics, making them suitable for various applications, including environmental and biomedical sensing. However, designing a high-resolution capacitive sensor interface system while maintaining power efficiency remains challenging. This article proposes a high-resolution energy-efficient highpass (HP) $\Delta\Sigma$ capacitance-to-digital converter (CDC) architecture. The architecture incorporates a 2 ${\textrm{nd}}$ -order HP $\Delta\Sigma$ modulator ( $\Delta\Sigma$ M) and a continuous-time capacitance-to-voltage converter (CT CVC). The proposed CDC achieves an excellent capacitance resolution of 5.85 aF $_\textrm{rms}$ , with a power efficiency of 46 fJ/conversion-step and an FoM $_\textrm{S}$ of 187.4 dB. The HP $\Delta\Sigma$ M, designed with superior power efficiency, offers a promising solution for high-resolution capacitive sensor applications. Compared to state-of-the-art, the proposed CDC achieves more than 2 $\times$ FoM $_\textrm{S}$ improvement while maintaining competitive FoM $_\textrm{W}$ .
- 10 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 6, 109-112
A 16-Channel Impedance-Readout IC With Synchronous Sampling and Baseline Cancelation for Fast Neural Electrical Impedance Tomography
Fast neural electrical impedance tomography (EIT) is a promising method to not only record neural activities but also to localize them in peripheral nerves in a minimally invasive way. A much higher image frame rate is required for this application than conventional impedance measurement applications, which generally adopt the I/Q demodulation technique. To achieve a high enough frame rate to capture neural activities along the peripheral nerve fascicle, this paper proposes synchronous sampling (SS) and fast baseline tracking based on successive approximation (SA). The SS method needs an injection of only a single or a few periods of square-wave current signal for the amplitude measurement by synchronously sampling the received voltage signal. The proposed SA-based baseline tracking provides fast signal recovery from unwanted motion artifacts or baseline drifts. The designed readout circuit uses a two-step conversion where its coarse bits are generated from a current-based baseline cancellation circuit and its fine bits from a following SAR ADC. Thanks to the baseline tracking based on the SS and SA, the proposed IC achieves a faster frame rate of 312 fps with continuous baseline update and 500 fps with constant baseline compared to state-of-the-art works. The implemented IC is validated by measuring a water-filled tank and reconstructing its tomographic image. The results show successful discrimination of varied impedance areas over the tank.
- 10 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 6, 109-112
A 16-Channel Impedance-Readout IC With Synchronous Sampling and Baseline Cancelation for Fast Neural Electrical Impedance Tomography
Fast neural electrical impedance tomography (EIT) is a promising method to not only record neural activities but also to localize them in peripheral nerves in a minimally invasive way. A much higher image frame rate is required for this application than conventional impedance measurement applications, which generally adopt the I/Q demodulation technique. To achieve a high enough frame rate to capture neural activities along the peripheral nerve fascicle, this paper proposes synchronous sampling (SS) and fast baseline tracking based on successive approximation (SA). The SS method needs an injection of only a single or a few periods of square-wave current signal for the amplitude measurement by synchronously sampling the received voltage signal. The proposed SA-based baseline tracking provides fast signal recovery from unwanted motion artifacts or baseline drifts. The designed readout circuit uses a two-step conversion where its coarse bits are generated from a current-based baseline cancellation circuit and its fine bits from a following SAR ADC. Thanks to the baseline tracking based on the SS and SA, the proposed IC achieves a faster frame rate of 312 fps with continuous baseline update and 500 fps with constant baseline compared to state-of-the-art works. The implemented IC is validated by measuring a water-filled tank and reconstructing its tomographic image. The results show successful discrimination of varied impedance areas over the tank.
- 2 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58 (3) , 720-731
A High-Efficiency Single-Mode Dual-Path Buck-Boost Converter With Reduced Inductor Current
This article presents a single-mode dual-path buck-boost converter (SDBBC) for mobile devices powered by lithium-ion batteries. Unlike the conventional buck-boost converter (CBBC), this SDBBC conducts buck and boost operations using a hybrid structure with two flying capacitors ($C_{F1}$ ,$C_{F2}$ ) and one inductor. This hybrid structure eliminates any mode transition between circuit configurations, covering both the buck and boost operations continuously within a single-mode operation. By consistently connecting the inductor to the load with a secondary path formed by$C_{F1}$ and$C_{F2}$ , the average of the inductor current ($I_{L}$ ) is always smaller than the load current ($I_{\mathrm {LOAD}}$ ) across all the output voltage conversion ratios, thus incurring low conduction loss and switch transition loss. Also, the current delivered to the load increases as the duty ratio increases, so the right half-plane (RHP) zero is removed. Therefore, the proposed SDBBC achieves high power efficiency seamlessly across the whole conversion range, 94.8% peak efficiency is achieved even with an inductor of 175$\text{m}\Omega $ dc resistance (DCR), and 95.58% efficiency is achieved in the boost operation at a heavy load current of 1 A using a large size inductor with 19$\text{m}\Omega $ DCR.- 2 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58 (3) , 720-731
A High-Efficiency Single-Mode Dual-Path Buck-Boost Converter With Reduced Inductor Current
This article presents a single-mode dual-path buck-boost converter (SDBBC) for mobile devices powered by lithium-ion batteries. Unlike the conventional buck-boost converter (CBBC), this SDBBC conducts buck and boost operations using a hybrid structure with two flying capacitors ($C_{F1}$ ,$C_{F2}$ ) and one inductor. This hybrid structure eliminates any mode transition between circuit configurations, covering both the buck and boost operations continuously within a single-mode operation. By consistently connecting the inductor to the load with a secondary path formed by$C_{F1}$ and$C_{F2}$ , the average of the inductor current ($I_{L}$ ) is always smaller than the load current ($I_{\mathrm {LOAD}}$ ) across all the output voltage conversion ratios, thus incurring low conduction loss and switch transition loss. Also, the current delivered to the load increases as the duty ratio increases, so the right half-plane (RHP) zero is removed. Therefore, the proposed SDBBC achieves high power efficiency seamlessly across the whole conversion range, 94.8% peak efficiency is achieved even with an inductor of 175$\text{m}\Omega $ dc resistance (DCR), and 95.58% efficiency is achieved in the boost operation at a heavy load current of 1 A using a large size inductor with 19$\text{m}\Omega $ DCR.- Open Access
- 18 October 2021
- Published by MDPI AG in Electronics
- Vol. 10 (20) , 2545
Conception and Simulation of a 2-Then-1-Bit/Cycle Noise-Shaping SAR ADC
A 2-then-1-bit/cycle noise-shaping successive-approximation register (SAR) analog-to-digital converter (ADC) for high sampling rate and high resolution is presented. The conversion consists of two phases of a coarse 2-bit/cycle SAR conversion for high speed and a fine 1-bit/cycle noise-shaping SAR conversion for high accuracy. The coarse conversion is performed by both voltage and time comparison for low power consumption. A redundancy after the coarse conversion corrects the error caused by a jitter noise during the time comparison. Additionally, a mismatch error between signal and reference paths is eliminated with the help of a tail-current-sharing comparator. The proposed ADC was designed in a 28 nm CMOS process, and the simulation result shows a 68.2 dB signal-to-noise distortion (SNDR) for a sampling rate of 480 MS/s and a bandwidth of 60 MHz with good energy efficiency.
- 18 October 2021
- Published by MDPI AG in Electronics
- Vol. 10 (20) , 2545
Open AccessConception and Simulation of a 2-Then-1-Bit/Cycle Noise-Shaping SAR ADC
A 2-then-1-bit/cycle noise-shaping successive-approximation register (SAR) analog-to-digital converter (ADC) for high sampling rate and high resolution is presented. The conversion consists of two phases of a coarse 2-bit/cycle SAR conversion for high speed and a fine 1-bit/cycle noise-shaping SAR conversion for high accuracy. The coarse conversion is performed by both voltage and time comparison for low power consumption. A redundancy after the coarse conversion corrects the error caused by a jitter noise during the time comparison. Additionally, a mismatch error between signal and reference paths is eliminated with the help of a tail-current-sharing comparator. The proposed ADC was designed in a 28 nm CMOS process, and the simulation result shows a 68.2 dB signal-to-noise distortion (SNDR) for a sampling rate of 480 MS/s and a bandwidth of 60 MHz with good energy efficiency.
- 17 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (11) , 3424-3433
An 85 dB DR 4 MHz BW Pipelined Noise-Shaping SAR ADC With 1–2 MASH Structure
A pipelined noise-shaping successive approximation register (NS-SAR) ADC with 1–2 multistage noise-shaping (MASH) structure is presented. Two-stage pipelined structure consisting of 5 bit NS-SAR and 4 bit NS-SAR quantizers enables 3rd-order noise-shaping. A single operational transconductance amplifier (OTA) is shared by an integrator for noise-shaping and a residue amplifier for pipelining to maximize the power efficiency. The measured dynamic range (DR) is 84.6 dB when the sampling rate is 83.3 MS/s, bandwidth is 4 MHz, and power consumption is 3.5 mW showing Schreier figure-of-merit (FoM S,DR ) of 175.2 dB. The proposed ADC structure greatly relaxes design requirement of each SAR quantizer and can achieve high resolution and wide bandwidth with good power efficiency.
- 17 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (11) , 3424-3433
An 85 dB DR 4 MHz BW Pipelined Noise-Shaping SAR ADC With 1–2 MASH Structure
A pipelined noise-shaping successive approximation register (NS-SAR) ADC with 1–2 multistage noise-shaping (MASH) structure is presented. Two-stage pipelined structure consisting of 5 bit NS-SAR and 4 bit NS-SAR quantizers enables 3rd-order noise-shaping. A single operational transconductance amplifier (OTA) is shared by an integrator for noise-shaping and a residue amplifier for pipelining to maximize the power efficiency. The measured dynamic range (DR) is 84.6 dB when the sampling rate is 83.3 MS/s, bandwidth is 4 MHz, and power consumption is 3.5 mW showing Schreier figure-of-merit (FoM S,DR ) of 175.2 dB. The proposed ADC structure greatly relaxes design requirement of each SAR quantizer and can achieve high resolution and wide bandwidth with good power efficiency.