Sitthisuntorn Supothina
Sitthisuntorn Supothina has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
Mantana Suwan
National Science and Technology Development Agency (NSTDA), National Metal and Materials Technology Center, Klong Luang, PathumThani, Thailand
3 shared publicationsM Suwan
National Metal and Materials Technology Center, National Science and Technology Development Agency (NSTDA), 114 Thailand Science Park, Phahonyothin Rd., Klong Luang, Pathum Thani 12120, Thailand
2 shared publicationsNuchjarin Sangwong
National Science and Technology Development Agency (NSTDA), National Metal and Materials Technology Center, Klong Luang, PathumThani, Thailand
2 shared publicationsSupatra Jinawath
Department of Materials Science, Faculty of Science, Chulalongkorn University, Pathumwan, Bangkok, Thailand
2 shared publicationsA. Jaroenworaluck
National Metal and Material Technology Centre, 114 Thailand Science Park Paholyothin Rd., Klong 1, Klong Luang, Pathumthani 12120, Thailand
1 shared publicationAnan Saenkhamai
Bio-Nano Material Science & Engineering, Department of Industrial Systems Engineering, Asian Institute of Technology, Klong Luang, Thailand
1 shared publication
Latest Publications
- Open Access
- 5 December 2022
- Published by MDPI AG in Inorganics
- Vol. 10 (12) , 242
Dissolution Performance of Carbon/Hydroxyapatite Nanocomposite Prepared from Fish Scales
The utilization of waste as raw materials in the production of functional materials is a growing area of interest to promote global sustainable growth. This work studied the microstructure, chemical properties, and phosphorus (P) dissolution efficiency of carbon/hydroxyapatite (HAP) nanocomposites derived from fish scale wastes, namely FSBCs. Tilapia scales were pyrolyzed at different temperatures (450–600 °C) and the dissolution performance of the biochars in acidic media was evaluated. The pyrolysis of fish scales yielded biochars which are carbon/HAP nanocomposites of which the characteristics, including the specific surface area, carbon content, degree of crystallinity of HAP, and the degree of CO32− substitution in HAP crystals, were dependent on the pyrolysis temperature and had an influence on the dissolution efficiency. P dissolution experiments suggested that the specific surface area and the presence of carbon in the composite played an important role during the dissolution process. The presence of the organic residues on the carbon could potentially block the calcium sites on HAP from citric acid and lower the dissolution efficiency. The ratio of CO32−/PO43− substitution in HAP also affected the dissolubility of FSBCs. The manipulation of their surface area and the CO32−/PO43− ratio of these materials would allow us to increase its solubility, which could benefit a prospective application such as P fertilizer production.
- 5 December 2022
- Published by MDPI AG in Inorganics
- Vol. 10 (12) , 242
Open AccessDissolution Performance of Carbon/Hydroxyapatite Nanocomposite Prepared from Fish Scales
The utilization of waste as raw materials in the production of functional materials is a growing area of interest to promote global sustainable growth. This work studied the microstructure, chemical properties, and phosphorus (P) dissolution efficiency of carbon/hydroxyapatite (HAP) nanocomposites derived from fish scale wastes, namely FSBCs. Tilapia scales were pyrolyzed at different temperatures (450–600 °C) and the dissolution performance of the biochars in acidic media was evaluated. The pyrolysis of fish scales yielded biochars which are carbon/HAP nanocomposites of which the characteristics, including the specific surface area, carbon content, degree of crystallinity of HAP, and the degree of CO32− substitution in HAP crystals, were dependent on the pyrolysis temperature and had an influence on the dissolution efficiency. P dissolution experiments suggested that the specific surface area and the presence of carbon in the composite played an important role during the dissolution process. The presence of the organic residues on the carbon could potentially block the calcium sites on HAP from citric acid and lower the dissolution efficiency. The ratio of CO32−/PO43− substitution in HAP also affected the dissolubility of FSBCs. The manipulation of their surface area and the CO32−/PO43− ratio of these materials would allow us to increase its solubility, which could benefit a prospective application such as P fertilizer production.
- Open Access
- 31 January 2022
- Published by Chiang Mai University in Chiang Mai Journal of Science
- Vol. 49 (1) , 93-104
Purification of TiO2 from Leucoxene for the Synthesis of NIR-Reflective Cr-doped CaTiO3 Pigment
This work aimed to explore the possibility of producing NIR-reflective pigment from Thai leucoxene which is an abundant mineral consisting of ~89 wt.% TiO2, 6 wt.% SiO2 and 5 wt.% other oxides such as Al2O3 and Fe2O3. The leucoxene was purified by selective leaching of undesired oxides with NaOH under hydrothermal condition. Effects of NaOH concentration, hydrothermal temperature and time were investigated. The results revealed that dissolutions of the SiO2 and Al2O3 increased with an increased NaOH concentration, while that of the ZrO2 and Fe2O3 remained the same, resulting in the increased TiO2 concentration. The SiO2 dissolution also increased with an increased temperature and time. The optimum leaching condition, i.e. 4 M NaOH, 180 °C and 60 min, yielded TiO2 content of 93.94 ±0.14 wt.%. The Cr-doped CaTiO3 pigments (CaCrxTi1-xO3; x = 0, 0.025, 0.05, 0.75 and 0.1), synthesized from the purified leucoxene, CaO and Cr2O3 by solid-state reaction at 1100 °C, exhibited brown color hue and NIR reflectance in a range of 34.5−59.8% depending on the Cr content. At the Cr content of 0.05, the pigment exhibited decent brownish appearance and modest NIR reflectance of 50.7% which was close to that of the pigment synthesized from pure rutile. The glaze consisting of 10 wt.% pigment had a glossy light brown appearance, and possessed NIR reflectance of 75.0 %, indicating a promising application in a field of NIR-reflective coating.
- 31 January 2022
- Published by Chiang Mai University in Chiang Mai Journal of Science
- Vol. 49 (1) , 93-104
Open AccessPurification of TiO2 from Leucoxene for the Synthesis of NIR-Reflective Cr-doped CaTiO3 Pigment
This work aimed to explore the possibility of producing NIR-reflective pigment from Thai leucoxene which is an abundant mineral consisting of ~89 wt.% TiO2, 6 wt.% SiO2 and 5 wt.% other oxides such as Al2O3 and Fe2O3. The leucoxene was purified by selective leaching of undesired oxides with NaOH under hydrothermal condition. Effects of NaOH concentration, hydrothermal temperature and time were investigated. The results revealed that dissolutions of the SiO2 and Al2O3 increased with an increased NaOH concentration, while that of the ZrO2 and Fe2O3 remained the same, resulting in the increased TiO2 concentration. The SiO2 dissolution also increased with an increased temperature and time. The optimum leaching condition, i.e. 4 M NaOH, 180 °C and 60 min, yielded TiO2 content of 93.94 ±0.14 wt.%. The Cr-doped CaTiO3 pigments (CaCrxTi1-xO3; x = 0, 0.025, 0.05, 0.75 and 0.1), synthesized from the purified leucoxene, CaO and Cr2O3 by solid-state reaction at 1100 °C, exhibited brown color hue and NIR reflectance in a range of 34.5−59.8% depending on the Cr content. At the Cr content of 0.05, the pigment exhibited decent brownish appearance and modest NIR reflectance of 50.7% which was close to that of the pigment synthesized from pure rutile. The glaze consisting of 10 wt.% pigment had a glossy light brown appearance, and possessed NIR reflectance of 75.0 %, indicating a promising application in a field of NIR-reflective coating.
- 27 December 2021
- Published by Taylor & Francis in Integrated Ferroelectrics
- Vol. 222 (1) , 283-292
Synthesis of NIR-Reflective Oxide Ceramic Orange Pigment from MgO and Leucoxene
A series of NIR-reflective brownish orange pigments comprising various amounts of Fe2O3 have been synthesized by a conventional solid-state reaction at 1100 °C. Magnesium titanate base pigment was synthesized from MgO and leucoxene mineral which was employed as TiO2 source. The resultant pigment had brownish gray appearance (L*a*b* = 68.67, 7.83, 18.68, respectively) and NIR reflectance of 81.0%. Incorporating the magnesium titanate pigment with various amounts of Fe2O3 (molar ratio (x) = 0.1, 0.3, 0.5, 0.7, 0.9 and 1.0) resulted in a change of color hue to brownish orange, and a change of NIR reflectance from 81.0 to 41.1% upon the increase of Fe2O3 content. Optical bang-gap energies derived from diffused reflectance spectra reduced from 2.75 eV for the magnesium titanate to 2.25, 2.20, 2.10, 1.90, 1.70 and 1.60 eV for pigments incorporated with 0.1, 0.3, 0.5, 0.7, 0.9 and 1.0 mole Fe2O3, respectively. At the optimum synthesis condition (x = 0.3), the pigment exhibited light brownish orange color hue (L*a*b* = 52.02, 23.94, 39.37) and NIR reflectance of 80.1%. An accelerated QUV weathering test according to the ASTM G154-16 standard revealed color fading (ΔE*) of only 0.95 indicating excellent weathering stability.
- 27 December 2021
- Published by Taylor & Francis in Integrated Ferroelectrics
- Vol. 222 (1) , 283-292
Synthesis of NIR-Reflective Oxide Ceramic Orange Pigment from MgO and Leucoxene
A series of NIR-reflective brownish orange pigments comprising various amounts of Fe2O3 have been synthesized by a conventional solid-state reaction at 1100 °C. Magnesium titanate base pigment was synthesized from MgO and leucoxene mineral which was employed as TiO2 source. The resultant pigment had brownish gray appearance (L*a*b* = 68.67, 7.83, 18.68, respectively) and NIR reflectance of 81.0%. Incorporating the magnesium titanate pigment with various amounts of Fe2O3 (molar ratio (x) = 0.1, 0.3, 0.5, 0.7, 0.9 and 1.0) resulted in a change of color hue to brownish orange, and a change of NIR reflectance from 81.0 to 41.1% upon the increase of Fe2O3 content. Optical bang-gap energies derived from diffused reflectance spectra reduced from 2.75 eV for the magnesium titanate to 2.25, 2.20, 2.10, 1.90, 1.70 and 1.60 eV for pigments incorporated with 0.1, 0.3, 0.5, 0.7, 0.9 and 1.0 mole Fe2O3, respectively. At the optimum synthesis condition (x = 0.3), the pigment exhibited light brownish orange color hue (L*a*b* = 52.02, 23.94, 39.37) and NIR reflectance of 80.1%. An accelerated QUV weathering test according to the ASTM G154-16 standard revealed color fading (ΔE*) of only 0.95 indicating excellent weathering stability.
- 30 November 2021
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 29 (02)
EFFECT OF MICRO-STRUCTURAL GEOMETRY ON LUBRICANT INFILTRATION AND PROPERTY OF SLIPPERY LIQUID-INFUSED POROUS SURFACES
- 30 November 2021
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 29 (02)
EFFECT OF MICRO-STRUCTURAL GEOMETRY ON LUBRICANT INFILTRATION AND PROPERTY OF SLIPPERY LIQUID-INFUSED POROUS SURFACES
- Open Access
- 17 June 2021
- Published by Wiley in Journal of Nanotechnology
- Vol. 2021, 1-7
Low-Temperature Synthesis of Vanadium Dioxide Thin Films by Sol-Gel Dip Coating Method
The vanadium dioxide (VO2) thin films were synthesized by sol-gel dipping on a glass slide substrate at low temperature of 500°C in a vacuum tube furnace at a pressure of 2×10−3mbar by 2-step calcination without an intermediate gas purging. Synthesis conditions, including temperature, vacuum pressure, and calcination steps in the vacuum tube furnace, were investigated to find the optimum condition that promoted the formation of VO2 phase. It was found that the 2nd calcination step was very important in realizing the monoclinic vanadium dioxide (VO2 (M)). The results of the valence electron analysis revealed the outstanding phase of VO2 and a small amount of V2O5 and V2O3 phases. The small crystallites of the VO2 were homogeneously distributed on the surface, and the grain was of an irregular shape of 220380nm in size. The films thickness was in a range of 6974nm. The film exhibited a metal-to-insulator transformation temperature of 68oC and good thermochromic property. Visible optical transmittance remained at 4050 when the samples temperature changed from 25 to 80°C for a near infrared (NIR) region.
- 17 June 2021
- Published by Wiley in Journal of Nanotechnology
- Vol. 2021, 1-7
Open AccessLow-Temperature Synthesis of Vanadium Dioxide Thin Films by Sol-Gel Dip Coating Method
The vanadium dioxide (VO2) thin films were synthesized by sol-gel dipping on a glass slide substrate at low temperature of 500°C in a vacuum tube furnace at a pressure of 2×10−3mbar by 2-step calcination without an intermediate gas purging. Synthesis conditions, including temperature, vacuum pressure, and calcination steps in the vacuum tube furnace, were investigated to find the optimum condition that promoted the formation of VO2 phase. It was found that the 2nd calcination step was very important in realizing the monoclinic vanadium dioxide (VO2 (M)). The results of the valence electron analysis revealed the outstanding phase of VO2 and a small amount of V2O5 and V2O3 phases. The small crystallites of the VO2 were homogeneously distributed on the surface, and the grain was of an irregular shape of 220380nm in size. The films thickness was in a range of 6974nm. The film exhibited a metal-to-insulator transformation temperature of 68oC and good thermochromic property. Visible optical transmittance remained at 4050 when the samples temperature changed from 25 to 80°C for a near infrared (NIR) region.
- Open Access
- 1 December 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 283 (1) , 012013
Transparent superhydrophobic coating application to the interlocking clay block for the microbial growth mitigation
Interlocking clay block is of widespread use in many countries due to its less labor-intensive design. The block comprises of considerable amount of pore structures; therefore water can easily penetrate into it causing deterioration by natural weathering as well as the growth of microbes on its surface. In this present work, a transparent, superhydrophobic coating was applied onto the block's surface to prevent water absorption. The coating which is a poly(methyl hydrogensiloxane) base containing fumed SiO2 nanoparticle was designed to possess surface topographic feature similar to that of the lotus leaf. After coating the block with the superhydrophobic compound, its water absorption decreased from 11.5 to 4.8% and porosity substantially decreased from 22.5 to 9.2%, while bulk and apparent densities did not change. Accelerated weathering test revealed that the coating had good stability. The coated samples exhibited growth inhibition of algae.
- 1 December 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 283 (1) , 012013
Open AccessTransparent superhydrophobic coating application to the interlocking clay block for the microbial growth mitigation
Interlocking clay block is of widespread use in many countries due to its less labor-intensive design. The block comprises of considerable amount of pore structures; therefore water can easily penetrate into it causing deterioration by natural weathering as well as the growth of microbes on its surface. In this present work, a transparent, superhydrophobic coating was applied onto the block's surface to prevent water absorption. The coating which is a poly(methyl hydrogensiloxane) base containing fumed SiO2 nanoparticle was designed to possess surface topographic feature similar to that of the lotus leaf. After coating the block with the superhydrophobic compound, its water absorption decreased from 11.5 to 4.8% and porosity substantially decreased from 22.5 to 9.2%, while bulk and apparent densities did not change. Accelerated weathering test revealed that the coating had good stability. The coated samples exhibited growth inhibition of algae.
- Open Access
- 10 March 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 182 (1) , 012003
Effect of Co and Pr doping on the properties of solar-reflective ZnFe2O4 dark pigment
- 10 March 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 182 (1) , 012003
Open AccessEffect of Co and Pr doping on the properties of solar-reflective ZnFe2O4 dark pigment
- Open Access
- 1 December 2014
- Published by Institution of Engineering and Technology (IET) in Micro & Nano Letters
- Vol. 9 (12) , 877-880
Increasing synthesis yield of K‐doped tungsten oxide nanowire using stirred hydrothermal reactor and its near‐infrared reflectance property
One‐dimensional nanostructured oxides are typically synthesised by the hydrothermal method in a small pressurised reactor under static conditions that usually results in a low synthesis yield. In this reported work, K‐doped tungsten oxide (K 2 W 4 O 13 ) nanowires were synthesised under stirred hydrothermal treatment of hydrous K 2 W 4 O 13 precursor in the presence of K 2 SO 4 employed as the shape‐directing agent to promote the formation of nanowires. Under static conditions (0 rpm), only 24.6% yield was obtained. The yield was significantly increased with the increase of stirring speed. The yield of 90.3%, almost four times the static condition, was obtained when synthesised under continuous stirring at 500 rpm. The samples synthesised from both the conditions have the same crystal structure, which is K 2 W 4 O 13 . However, the difference in particle morphology was observed; the average diameter of 11.4 ± 0.3 nm and the length up to several hundred micrometres were obtained from the stirred condition, while more irregularities of the nanowires (average diameter of 7.1 ± 1.1 nm and very diverse length) were obtained under static conditions. The more uniformity observed under stirred hydrothermal conditions is attributed to the more uniform crystallisation process attained under the stirring condition. A high near‐infrared (NIR) reflectance of 91.3% suggests its NIR shielding ability.
- 1 December 2014
- Published by Institution of Engineering and Technology (IET) in Micro & Nano Letters
- Vol. 9 (12) , 877-880
Open AccessIncreasing synthesis yield of K‐doped tungsten oxide nanowire using stirred hydrothermal reactor and its near‐infrared reflectance property
One‐dimensional nanostructured oxides are typically synthesised by the hydrothermal method in a small pressurised reactor under static conditions that usually results in a low synthesis yield. In this reported work, K‐doped tungsten oxide (K 2 W 4 O 13 ) nanowires were synthesised under stirred hydrothermal treatment of hydrous K 2 W 4 O 13 precursor in the presence of K 2 SO 4 employed as the shape‐directing agent to promote the formation of nanowires. Under static conditions (0 rpm), only 24.6% yield was obtained. The yield was significantly increased with the increase of stirring speed. The yield of 90.3%, almost four times the static condition, was obtained when synthesised under continuous stirring at 500 rpm. The samples synthesised from both the conditions have the same crystal structure, which is K 2 W 4 O 13 . However, the difference in particle morphology was observed; the average diameter of 11.4 ± 0.3 nm and the length up to several hundred micrometres were obtained from the stirred condition, while more irregularities of the nanowires (average diameter of 7.1 ± 1.1 nm and very diverse length) were obtained under static conditions. The more uniformity observed under stirred hydrothermal conditions is attributed to the more uniform crystallisation process attained under the stirring condition. A high near‐infrared (NIR) reflectance of 91.3% suggests its NIR shielding ability.
- 1 November 2011
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 31 (14) , 2453-2458
Effect of synthesis condition on morphology and yield of hydrothermally grown SnO2 nanorod clusters
- 1 November 2011
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 31 (14) , 2453-2458
Effect of synthesis condition on morphology and yield of hydrothermally grown SnO2 nanorod clusters