Jian Zhan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jian Zhan has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Eugen Brühwiler
EPFL
3 shared publications - Emmanuel Denarié
École Polytechnique Fédérale de Lausanne (EPFL)
2 shared publications Minghong Qiu
2 shared publicationsAlain Nussbaumer
1 shared publication- Alain Nussbaumer
Resilient Steel Structures Laboratory (RESSLab), School of Architecture, Civil and Environmental Engineering (ENAC), École Polytechnique Fédérale de Lausanne (EPFL), Lausanne, Switzerland
1 shared publication Eugen Brühwiler
1 shared publication
Latest Publications
- Open Access
- 19 April 2026
- Published by Elsevier in International Journal of Fatigue
- Vol. 210
Two-level block fatigue behavior of UHPFRC uniaxial tension specimens
- 19 April 2026
- Published by Elsevier in International Journal of Fatigue
- Vol. 210
Open AccessTwo-level block fatigue behavior of UHPFRC uniaxial tension specimens
- Open Access
- 3 June 2025
- Published by Elsevier in Engineering Structures
- Vol. 339
Low-cost and ductile prestressed UHPC beams with hybrid reinforcement: Experiments and design methods
- 3 June 2025
- Published by Elsevier in Engineering Structures
- Vol. 339
Open AccessLow-cost and ductile prestressed UHPC beams with hybrid reinforcement: Experiments and design methods
- Open Access
- 11 December 2023
- Published by Elsevier in International Journal of Fatigue
- Vol. 180
Influence of fiber orientation on the high cycle tensile fatigue resistance of Ultra-High Performance Fiber Reinforced Cementitious Composites (UHPFRC)
- 11 December 2023
- Published by Elsevier in International Journal of Fatigue
- Vol. 180
Open AccessInfluence of fiber orientation on the high cycle tensile fatigue resistance of Ultra-High Performance Fiber Reinforced Cementitious Composites (UHPFRC)
- Open Access
- 4 June 2023
- Published by Iowa State University
- Vol. 3 (1)
Influence of Fiber Orientation on the Elastic Limit Tensile Stress of UHPFRC
The elastic limit tensile stress of UHPFRC is governed by contributions of the cementitious matrix and the fibrous skeleton. This paper finds that fiber orientation has significant influence on the matrix tensile strength of UHPFRC, while this is not considered in current estimation of elastic limit tensile stress. An original model relating fiber orientation to the elastic limit tensile stress is proposed. Uniaxial tensile tests have been conducted on ten dumbbell-shaped specimens, whose local fiber volume and orientation are determined using a magnetic probe before testing. Based on the results of local fiber distribution, the influence of fiber orientation on the elastic limit tensile stress is discussed, showing that the proposed model estimates well the elastic limit tensile stress of UHPFRC.
- 4 June 2023
- Published by Iowa State University
- Vol. 3 (1)
Open AccessInfluence of Fiber Orientation on the Elastic Limit Tensile Stress of UHPFRC
The elastic limit tensile stress of UHPFRC is governed by contributions of the cementitious matrix and the fibrous skeleton. This paper finds that fiber orientation has significant influence on the matrix tensile strength of UHPFRC, while this is not considered in current estimation of elastic limit tensile stress. An original model relating fiber orientation to the elastic limit tensile stress is proposed. Uniaxial tensile tests have been conducted on ten dumbbell-shaped specimens, whose local fiber volume and orientation are determined using a magnetic probe before testing. Based on the results of local fiber distribution, the influence of fiber orientation on the elastic limit tensile stress is discussed, showing that the proposed model estimates well the elastic limit tensile stress of UHPFRC.
- Open Access
- 6 May 2023
- Published by Elsevier in Cement and Concrete Composites
- Vol. 140, 105122
Elastic limit tensile stress of UHPFRC: Method of determination and effect of fiber orientation
- 6 May 2023
- Published by Elsevier in Cement and Concrete Composites
- Vol. 140, 105122
Open AccessElastic limit tensile stress of UHPFRC: Method of determination and effect of fiber orientation
- 1 March 2019
- Published by Tsinghua University Press in Journal of Highway and Transportation Research and Development (English Edition)
- Vol. 13 (1) , 50-59
Multiparameter Fatigue Analysis of a Steel–Super-Toughness-Concrete Lightweight Composite Bridge Deck
This study aimed to comprehensively analyze the effects of the thickness of a super-toughness concrete (STC) layer, the thickness of diaphragms, and the spacing of stud shear connectors on the fatigue property of a lightweight composite bridge deck. A multiparameter analysis was performed on a steel-STC lightweight composite deck to facilitate its fatigue design. Based on a real bridge, a serial local finite element model was built to calculate the fatigue stress range of the typical fatigue-prone cracking details of the steel bridge deck under different combinations of the three parameters. On the basis of the FE analysis, the nominal stress of each fatigue-prone detail was obtained, and the following observations were obtained. First, the lightweight composite bridge deck structure could strongly enhance the local stiffness of the steel bridge deck, but its contribution to the global stiffness of the bridge deck is limited. Second, increasing the STC layer thickness from 45 mm to 60 mm could further reduce the fatigue stress range of fatigue-prone details in the steel deck. Third, increasing the thickness of the floor beams could improve the cracking details at the U-rib-to-diaphragm connection and butt weld at the U-rih lower edge, and the stress range reduction is about 20%–29%. Fourth, reducing the spacing of the stud shear connectors could obviously decrease the stress range of the U-rib-diaphragm welded joints and the arc cutouts in floor beams, and the stress range decreases by 22.01%–27.96%.
- 1 March 2019
- Published by Tsinghua University Press in Journal of Highway and Transportation Research and Development (English Edition)
- Vol. 13 (1) , 50-59
Multiparameter Fatigue Analysis of a Steel–Super-Toughness-Concrete Lightweight Composite Bridge Deck
This study aimed to comprehensively analyze the effects of the thickness of a super-toughness concrete (STC) layer, the thickness of diaphragms, and the spacing of stud shear connectors on the fatigue property of a lightweight composite bridge deck. A multiparameter analysis was performed on a steel-STC lightweight composite deck to facilitate its fatigue design. Based on a real bridge, a serial local finite element model was built to calculate the fatigue stress range of the typical fatigue-prone cracking details of the steel bridge deck under different combinations of the three parameters. On the basis of the FE analysis, the nominal stress of each fatigue-prone detail was obtained, and the following observations were obtained. First, the lightweight composite bridge deck structure could strongly enhance the local stiffness of the steel bridge deck, but its contribution to the global stiffness of the bridge deck is limited. Second, increasing the STC layer thickness from 45 mm to 60 mm could further reduce the fatigue stress range of fatigue-prone details in the steel deck. Third, increasing the thickness of the floor beams could improve the cracking details at the U-rib-to-diaphragm connection and butt weld at the U-rih lower edge, and the stress range reduction is about 20%–29%. Fourth, reducing the spacing of the stud shear connectors could obviously decrease the stress range of the U-rib-diaphragm welded joints and the arc cutouts in floor beams, and the stress range decreases by 22.01%–27.96%.