Prakash Ghose
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Prakash Ghose has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
Rishitosh Ranjan
School of Mechanical Engineering, Kalinga Institute of Industrial Technology (Deemed to be University), Bhubaneswar, India
4 shared publications- Amitava Datta
Department of Power Engineering, Jadavpur University, Kolkata, India
3 shared publications Jitendra Patra
Department of Power Engineering, Jadavpur University, Salt Lake Campus, Kolkata, India
3 shared publicationsTarak Kumar Sahoo
School of Mechanical Engineering, KIIT University, Bhubaneswar, India
3 shared publicationsAchintya Mukhopadhyay
Department of Mechanical Engineering, Jadavpur University, Kolkata, India
2 shared publications- Achintya Mukhopadhyay
Jadavpur University
2 shared publications
Latest Publications
- 8 May 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 238 (18) , 9293-9306
Comparison of discriminant analysis coupled with principal component analysis (PCA-DA) and back propagation neural network (BPNN) as classification model for decision support system in porous ceramic matrix (PCM) based burner
Two classification models discriminant analysis coupled with principal component analysis (PCA-DA) and back propagation neural network (BPNN), are for the first time applied for decision support system in porous ceramic matrix (PCM) based burner. The PCM based burner is simulated numerically, and 121 pairs of gas and solid temperature profiles are generated as input data. The operation of PCM based burner is classified into four, on the basis of important properties of PCM like extinction coefficient and convective coupling. With the help of the data, the classification models are developed. The classification models are monitored and analyzed through different plots and classification parameters like specificity, sensitivity and precision. Further, new samples are correctly allocated to their corresponding class by the classification models. The classification models are also explored and compared under noisy data (2% and 5%). The performances of both the classification models are found to be good for no noise case with all the parameters like sensitivity, specificity, and precision values greater than 0.69, for both the models. However, with 2% noise case, BPNN performs better than PCA-DA. The minimum value of parameters (sn, sp, & pr) is 0.67 with BPNN and 0.50 with PCA-DA, respectively. Under 5% noise, the minimum values of the parameters dropped to 0.47 for PCA-DA and 0.50 for BPNN, respectively. With the help of plots though, the new samples are easily identified to their correct class 3.
- 8 May 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 238 (18) , 9293-9306
Comparison of discriminant analysis coupled with principal component analysis (PCA-DA) and back propagation neural network (BPNN) as classification model for decision support system in porous ceramic matrix (PCM) based burner
Two classification models discriminant analysis coupled with principal component analysis (PCA-DA) and back propagation neural network (BPNN), are for the first time applied for decision support system in porous ceramic matrix (PCM) based burner. The PCM based burner is simulated numerically, and 121 pairs of gas and solid temperature profiles are generated as input data. The operation of PCM based burner is classified into four, on the basis of important properties of PCM like extinction coefficient and convective coupling. With the help of the data, the classification models are developed. The classification models are monitored and analyzed through different plots and classification parameters like specificity, sensitivity and precision. Further, new samples are correctly allocated to their corresponding class by the classification models. The classification models are also explored and compared under noisy data (2% and 5%). The performances of both the classification models are found to be good for no noise case with all the parameters like sensitivity, specificity, and precision values greater than 0.69, for both the models. However, with 2% noise case, BPNN performs better than PCA-DA. The minimum value of parameters (sn, sp, & pr) is 0.67 with BPNN and 0.50 with PCA-DA, respectively. Under 5% noise, the minimum values of the parameters dropped to 0.47 for PCA-DA and 0.50 for BPNN, respectively. With the help of plots though, the new samples are easily identified to their correct class 3.
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3007 (1)
Energy, exergy and emission analysis of traditional and improved cookstoves: A comparative study
This paper presents a comparative study on thermal performance between a traditional cookstove and an improved cookstove based on energy, exergy and emission. Intending to diminish the use of wood for daily domestic cooking practice in local area, this paper emphasizes on the optimum and efficient utilization of plant-based biomass (peanut shell) as fuel for cookstoves. The thermal and emission performances of two stoves were determined by lab-based water boiling test (WBT). The energy and exergy efficiencies of traditional stove for cold start were 10.70±2.26% and 1.26±0.96%, respectively, whereas those for hot start were 13.21±2.18% and 1.46±1.02%, respectively. Similarly for improved cookstove, the energy and exergy efficiencies were recorded 19.28±1.89% and 3.32±1.11% in cold start condition, and those were 23±1.93% and 4.56±1.23% in hot start condition. The time average values of carbon monoxide (CO) and particulate matter (PM) were recorded as 75±6.21ppm and 7000±1900 µg/m3, respectively for traditional cookstove, and those for improved one were 15±4.89 ppm and the 3806±1175 µg/m3, respectively.
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3007 (1)
Open AccessEnergy, exergy and emission analysis of traditional and improved cookstoves: A comparative study
This paper presents a comparative study on thermal performance between a traditional cookstove and an improved cookstove based on energy, exergy and emission. Intending to diminish the use of wood for daily domestic cooking practice in local area, this paper emphasizes on the optimum and efficient utilization of plant-based biomass (peanut shell) as fuel for cookstoves. The thermal and emission performances of two stoves were determined by lab-based water boiling test (WBT). The energy and exergy efficiencies of traditional stove for cold start were 10.70±2.26% and 1.26±0.96%, respectively, whereas those for hot start were 13.21±2.18% and 1.46±1.02%, respectively. Similarly for improved cookstove, the energy and exergy efficiencies were recorded 19.28±1.89% and 3.32±1.11% in cold start condition, and those were 23±1.93% and 4.56±1.23% in hot start condition. The time average values of carbon monoxide (CO) and particulate matter (PM) were recorded as 75±6.21ppm and 7000±1900 µg/m3, respectively for traditional cookstove, and those for improved one were 15±4.89 ppm and the 3806±1175 µg/m3, respectively.
- Open Access
- 30 December 2023
- Published by Akademia Baru Publishing in Journal of Advanced Research in Applied Sciences and Engineering Technology
- Vol. 36 (2) , 36-55
Buoyancy-Driven Ventilation in the Interior-Most Flats of an Apartment Building with Different Corridor Vent Opening Condition
In the present work, computational simulations are conducted for an apartment building to investigate the bouncy-driven airflow in the corridor and inside the rooms. Two types of corridor vent openings are provided through which the hot light air moves to the ambient. Two floors are considered for the study. The simulations are conducted with three different temperature difference conditions between walls and room inside air such as; ∆T=10OC, ∆T=15OC, ∆T=20OC for two different corridor vent opening configurations. When the corridor vent openings are kept only in front of the doors and windows, recirculation zones below the roof near the air entry region are observed and part of the air escaped through the inlet. In the case of a wide corridor vent opening, air does not escape through the inlet. With increase in ΔT, the airflow increases irrespective of vent positions. Mainly the area of the rooms is well ventilated closer to the door position. It is also observed that the lower floor is relatively well-ventilated as compared to the upper floor. The ACH increases with increase in vent opening and it also increases with increase in ∆T.
- 30 December 2023
- Published by Akademia Baru Publishing in Journal of Advanced Research in Applied Sciences and Engineering Technology
- Vol. 36 (2) , 36-55
Open AccessBuoyancy-Driven Ventilation in the Interior-Most Flats of an Apartment Building with Different Corridor Vent Opening Condition
In the present work, computational simulations are conducted for an apartment building to investigate the bouncy-driven airflow in the corridor and inside the rooms. Two types of corridor vent openings are provided through which the hot light air moves to the ambient. Two floors are considered for the study. The simulations are conducted with three different temperature difference conditions between walls and room inside air such as; ∆T=10OC, ∆T=15OC, ∆T=20OC for two different corridor vent opening configurations. When the corridor vent openings are kept only in front of the doors and windows, recirculation zones below the roof near the air entry region are observed and part of the air escaped through the inlet. In the case of a wide corridor vent opening, air does not escape through the inlet. With increase in ΔT, the airflow increases irrespective of vent positions. Mainly the area of the rooms is well ventilated closer to the door position. It is also observed that the lower floor is relatively well-ventilated as compared to the upper floor. The ACH increases with increase in vent opening and it also increases with increase in ∆T.
- 28 November 2023
- Published by Springer Nature
- p. 105-113
Computational Modelling on Lithium-Ion Battery Pack Forced Convection Cooling
- 28 November 2023
- Published by Springer Nature
- p. 105-113
Computational Modelling on Lithium-Ion Battery Pack Forced Convection Cooling
- Open Access
- 21 November 2023
- Published by Springer Nature in Research Square
Investigation of safe operating conditions for reducing acid corrosion and ABS deposition in rotary air preheater using computational fluid dynamics
A rotary air preheater is an important energy recovery device that can reduce energy wastage to a great extent. The major issue associated with this device is the blockage inside the rotary matrix mainly due to chemical deposition such as; sulphuric acid and Ammonium Bi sulphate (ABS). Moreover, these compound causes substantial damage to air preheater element in terms of corrosion. The current research has been carried out to explore the optimum parametric conditions such as; inlet air and hot gas temperature, hot gas and air mass flow rate and rotational speed of rotary matrix to minimize the acid corrosion and ABS deposition. The dew point temperature (DPT) of sulphuric acid and Ammonium bi-sulphate (ABS) formation temperature were evaluated using correlations. From the simulation, it is observed that with increase in air/hot flue gas temperature, the acid corrosion area and ABS formation region decreases. When the mass flow rate of air and hot flue gas increases equally, the acid corrosion and ABS formation region increases along the cold airflow direction. With a lower mass flow rate, the ABS deposition and acid corrosion area becomes more uniform near the cold end only. Near the hot end, it seems to be corrosion-free.
- 21 November 2023
- Published by Springer Nature in Research Square
Open AccessInvestigation of safe operating conditions for reducing acid corrosion and ABS deposition in rotary air preheater using computational fluid dynamics
A rotary air preheater is an important energy recovery device that can reduce energy wastage to a great extent. The major issue associated with this device is the blockage inside the rotary matrix mainly due to chemical deposition such as; sulphuric acid and Ammonium Bi sulphate (ABS). Moreover, these compound causes substantial damage to air preheater element in terms of corrosion. The current research has been carried out to explore the optimum parametric conditions such as; inlet air and hot gas temperature, hot gas and air mass flow rate and rotational speed of rotary matrix to minimize the acid corrosion and ABS deposition. The dew point temperature (DPT) of sulphuric acid and Ammonium bi-sulphate (ABS) formation temperature were evaluated using correlations. From the simulation, it is observed that with increase in air/hot flue gas temperature, the acid corrosion area and ABS formation region decreases. When the mass flow rate of air and hot flue gas increases equally, the acid corrosion and ABS formation region increases along the cold airflow direction. With a lower mass flow rate, the ABS deposition and acid corrosion area becomes more uniform near the cold end only. Near the hot end, it seems to be corrosion-free.
- 6 November 2023
- Published by ASME International in ASME Journal of Heat and Mass Transfer
- Vol. 146 (1) , 1-28
Computational Modeling of Walking Beam Type Reheat Furnace for the Prediction of Slab Heating and Scale Formation
Computational modeling using the high-viscosity laminar flow approach was applied to study the effect of slab crossing time on slab heating and scale growth. Simulation of an existing industrial walking beam reheating furnace with four zones, outer refractory body, skid, slab, and fluid zone is considered. The fuel used was a mixture of coke oven and blast furnace gas. Preheated air is supplied co-axially with the fuel mixture. The combustion simulation is performed using the constrained equilibrium mixture fraction model. From the results, it has been observed that with an increase in slab residence time, the slab temperature and scale growth increase across the slab. For the system considered, with a fuel mass flowrate of 70,000 kg/h, 150–180 min of slab crossing time is appropriate to obtain desired slab temperature at the discharge end. The overall equivalence ratio is taken as Φ = 1 (fuel/air ratio is the same as stoichiometric ratio). The maximum slab scale thickness is evaluated as 2.4 mm at the discharged end for 180 min of slab crossing time.
- 6 November 2023
- Published by ASME International in ASME Journal of Heat and Mass Transfer
- Vol. 146 (1) , 1-28
Computational Modeling of Walking Beam Type Reheat Furnace for the Prediction of Slab Heating and Scale Formation
Computational modeling using the high-viscosity laminar flow approach was applied to study the effect of slab crossing time on slab heating and scale growth. Simulation of an existing industrial walking beam reheating furnace with four zones, outer refractory body, skid, slab, and fluid zone is considered. The fuel used was a mixture of coke oven and blast furnace gas. Preheated air is supplied co-axially with the fuel mixture. The combustion simulation is performed using the constrained equilibrium mixture fraction model. From the results, it has been observed that with an increase in slab residence time, the slab temperature and scale growth increase across the slab. For the system considered, with a fuel mass flowrate of 70,000 kg/h, 150–180 min of slab crossing time is appropriate to obtain desired slab temperature at the discharge end. The overall equivalence ratio is taken as Φ = 1 (fuel/air ratio is the same as stoichiometric ratio). The maximum slab scale thickness is evaluated as 2.4 mm at the discharged end for 180 min of slab crossing time.
- 18 May 2023
- Published by Wiley in Journal of Thermal Science and Engineering Applications
- Vol. 15 (7) , 1-20
Performance Prediction of a Model Rotary Air Preheater Through Porous Media Approach
Rotary regenerative heat exchangers or rotary regenerators are used for various heat recovery applications in order to fulfill the energy requirements. Rotary air preheater is a rotary regenerative heat exchanger which is widely used in thermal power plants to recover heat energy from exhaust flue gases. Several numerical works are being carried out to improve the performance and reduce the cost of the rotary air preheater. However, the accurate modeling of the internal structure of the matrix demands a lot of CPU power and is a big challenge for researchers. To overcome this problem, the rotary matrix of the preheater can be modeled using a porous media approach. But a thorough investigation is required to evaluate its performance. In this work, rotary air preheater simulations were carried out by applying a porous media approach. The effects of different operating conditions, such as speed of rotor, the mass flowrate of incoming fluids, material of matrix, and inlet temperature of hot fluid on the performance of rotary air preheater were investigated. Simulation results were validated with the results obtained from the experimentation performed in-house. The effect of fluid flowrates on pressure drop was also studied. It has been observed that the rotational speed of the rotor significantly affects the performance of the preheater, while the inlet temperature of hot fluid has a negligible effect on performance.
- 18 May 2023
- Published by Wiley in Journal of Thermal Science and Engineering Applications
- Vol. 15 (7) , 1-20
Performance Prediction of a Model Rotary Air Preheater Through Porous Media Approach
Rotary regenerative heat exchangers or rotary regenerators are used for various heat recovery applications in order to fulfill the energy requirements. Rotary air preheater is a rotary regenerative heat exchanger which is widely used in thermal power plants to recover heat energy from exhaust flue gases. Several numerical works are being carried out to improve the performance and reduce the cost of the rotary air preheater. However, the accurate modeling of the internal structure of the matrix demands a lot of CPU power and is a big challenge for researchers. To overcome this problem, the rotary matrix of the preheater can be modeled using a porous media approach. But a thorough investigation is required to evaluate its performance. In this work, rotary air preheater simulations were carried out by applying a porous media approach. The effects of different operating conditions, such as speed of rotor, the mass flowrate of incoming fluids, material of matrix, and inlet temperature of hot fluid on the performance of rotary air preheater were investigated. Simulation results were validated with the results obtained from the experimentation performed in-house. The effect of fluid flowrates on pressure drop was also studied. It has been observed that the rotational speed of the rotor significantly affects the performance of the preheater, while the inlet temperature of hot fluid has a negligible effect on performance.
- 28 April 2023
- Published by Springer Nature in Journal of Engineering Physics and Thermophysics
- Vol. 96 (2) , 1-12
Computational Modeling of Partial Phase Change in the Hypoeutectic Binary Alloy Al–7Si Melt over a Cooled Tilted Plate
- 28 April 2023
- Published by Springer Nature in Journal of Engineering Physics and Thermophysics
- Vol. 96 (2) , 1-12
Computational Modeling of Partial Phase Change in the Hypoeutectic Binary Alloy Al–7Si Melt over a Cooled Tilted Plate
- 1 January 2023
- Published by Begell House Inc. Publishers in Computational Thermal Sciences: An International Journal
- Vol. 15 (6) , 19-40
Computational modelling for the performance prediction of quad-sector rotary air preheater and comparative study with tri-sector and bi-sector rotary air preheater
Rotary air preheaters are mainly used to improve the economy of a steam power plant by preheating the air with the help of hot flue gases from the boiler. Modern steam power plants are preferring tri-sector and quad-sector rotary air preheaters over bi-sector due to their better performance and lower leakage. In the present work, thermal behavior of a quad-sector rotary air preheater is the focus using computational fluid dynamics. The porous media approach is used for numerical simulation assuming local thermal equilibrium condition between fluid and solid. The performance of the air preheater is accessed by effectiveness and pressure drop. Porosity is estimated for four different cell shapes, which are used in the rotary preheater core for numerical investigation. The study reveals that the core consisting of a triangular cell has the highest effectiveness. The effect of porosity on performance is also investigated for various cell shapes. The effect of important operating parameters, such as rotor speed, aspect ratio, and mass flow rate of fluids on the effectiveness, as well as pressure drop is investigated for a quad-sector rotary air preheater. The study ends with a comparative performance analysis between bi-, tri-, and quad-sector rotary air preheaters. The performance of quad-sector air preheater is found to be better than other two preheaters in terms of effectiveness, whereas its pressure drop is maximum.
- 1 January 2023
- Published by Begell House Inc. Publishers in Computational Thermal Sciences: An International Journal
- Vol. 15 (6) , 19-40
Computational modelling for the performance prediction of quad-sector rotary air preheater and comparative study with tri-sector and bi-sector rotary air preheater
Rotary air preheaters are mainly used to improve the economy of a steam power plant by preheating the air with the help of hot flue gases from the boiler. Modern steam power plants are preferring tri-sector and quad-sector rotary air preheaters over bi-sector due to their better performance and lower leakage. In the present work, thermal behavior of a quad-sector rotary air preheater is the focus using computational fluid dynamics. The porous media approach is used for numerical simulation assuming local thermal equilibrium condition between fluid and solid. The performance of the air preheater is accessed by effectiveness and pressure drop. Porosity is estimated for four different cell shapes, which are used in the rotary preheater core for numerical investigation. The study reveals that the core consisting of a triangular cell has the highest effectiveness. The effect of porosity on performance is also investigated for various cell shapes. The effect of important operating parameters, such as rotor speed, aspect ratio, and mass flow rate of fluids on the effectiveness, as well as pressure drop is investigated for a quad-sector rotary air preheater. The study ends with a comparative performance analysis between bi-, tri-, and quad-sector rotary air preheaters. The performance of quad-sector air preheater is found to be better than other two preheaters in terms of effectiveness, whereas its pressure drop is maximum.