Mohammad S. Uddin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohammad S. Uddin has a total of 203 co-authors. Here are the top co-authors by number of shared publications:
M. Baba
Tohoku University
24 shared publications- Ferenc Ditrói
HUN-REN Institute for Nuclear Research, Debrecen, Hungary
23 shared publications - Masayuki Hagiwara
High Energy Accelerator Research Organization (KEK)
23 shared publications A. Hermanne
Vrije Universiteit Brussel (VUB)
21 shared publicationsS. Takács
Hungarian Academy of Sciences (ATOMKI)
18 shared publicationsF. Tárkányi
Hungarian Academy of Sciences (ATOMKI)
15 shared publications
Latest Publications
- Open Access
- 11 September 2026
- Published by Elsevier in SSRN Electronic Journal
Measurements of cross sections up to 15.8 MeV and TALYS–TASMAN analysis of cobalt-isotope production in proton irradiation of natural iron
The excitation functions for the natFe(p,x)55,57,58Co reactions were measured using the stacked-foil activation technique at proton energies up to 15.8 MeV. Measurements below 4 MeV were performed with the 3 MV tandem accelerator in Dhaka, Bangladesh. Higher-energy measurements were carried out with the BC1710 cyclotron at Forschungszentrum Jülich in Germany. The typical cross-section uncertainty of the measured cross section was 7–18%, increasing to approximately 30% for a few low-energy ⁵⁸Co data points. The new results were combined with selected experimental data, including literature data for the natFe(p,x)56Co reaction, and analyzed using the TALYS–TASMAN framework. Selected optical-model, level-density, and gamma-ray strength-function parameters were adjusted by statistical optimization. Normalized residuals and a 3σ criterion were used to assess data consistency and identify outliers. The optimized calculations gave reduced χ² values of 1.27 for 55Co, 1.35 for 56Co, 1.34 for 57Co, and 1.48 for 58Co. The calculations reproduce most retained experimental data over several orders of magnitude. Residual analysis identifies dataset-dependent offsets and outliers. The fitted proton optical-model radius adjustment also differs among the dominant iron-isotope contributions to the investigated production channels, indicating that a single global adjustment is not optimal for all cases. The results strengthen the low-energy proton-reaction database for natural iron and provide an uncertainty-based assessment of model performance and experimental consistency.
- 11 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMeasurements of cross sections up to 15.8 MeV and TALYS–TASMAN analysis of cobalt-isotope production in proton irradiation of natural iron
The excitation functions for the natFe(p,x)55,57,58Co reactions were measured using the stacked-foil activation technique at proton energies up to 15.8 MeV. Measurements below 4 MeV were performed with the 3 MV tandem accelerator in Dhaka, Bangladesh. Higher-energy measurements were carried out with the BC1710 cyclotron at Forschungszentrum Jülich in Germany. The typical cross-section uncertainty of the measured cross section was 7–18%, increasing to approximately 30% for a few low-energy ⁵⁸Co data points. The new results were combined with selected experimental data, including literature data for the natFe(p,x)56Co reaction, and analyzed using the TALYS–TASMAN framework. Selected optical-model, level-density, and gamma-ray strength-function parameters were adjusted by statistical optimization. Normalized residuals and a 3σ criterion were used to assess data consistency and identify outliers. The optimized calculations gave reduced χ² values of 1.27 for 55Co, 1.35 for 56Co, 1.34 for 57Co, and 1.48 for 58Co. The calculations reproduce most retained experimental data over several orders of magnitude. Residual analysis identifies dataset-dependent offsets and outliers. The fitted proton optical-model radius adjustment also differs among the dominant iron-isotope contributions to the investigated production channels, indicating that a single global adjustment is not optimal for all cases. The results strengthen the low-energy proton-reaction database for natural iron and provide an uncertainty-based assessment of model performance and experimental consistency.
- 10 August 2026
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 114 (10) , 721-729
Excitation functions for the formation of 55,57,58m+g Co with deuteron induced reactions on natural iron
Excitation functions of the reactions nat Fe(d,x) 55,57,58m+g Co were measured for deuteron energies of 15–35 MeV using the stacked-foil activation technique. The measured cross sections were compared with the available experimental data as well as with model calculations. The model calculations, using the TALYS-2.0 code, reproduced our measured data after a careful selection of a few input parameters. In this work, we report the cross section data with higher precision and extend them above 22 MeV. The thick target yield of 55 Co estimated from the measured excitation function amounted to 45 MBq/μAh for the energy window of E d = 40 → 25 MeV. Using this energy window, 96 % pure 55 Co could be obtained using natural iron target.
- 10 August 2026
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 114 (10) , 721-729
Excitation functions for the formation of 55,57,58m+g Co with deuteron induced reactions on natural iron
Excitation functions of the reactions nat Fe(d,x) 55,57,58m+g Co were measured for deuteron energies of 15–35 MeV using the stacked-foil activation technique. The measured cross sections were compared with the available experimental data as well as with model calculations. The model calculations, using the TALYS-2.0 code, reproduced our measured data after a careful selection of a few input parameters. In this work, we report the cross section data with higher precision and extend them above 22 MeV. The thick target yield of 55 Co estimated from the measured excitation function amounted to 45 MBq/μAh for the energy window of E d = 40 → 25 MeV. Using this energy window, 96 % pure 55 Co could be obtained using natural iron target.
- 18 March 2026
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 114 (6) , 423-431
Excitation functions of 85 Rb( p,n ) 85m,g Sr and 87 Rb( p,n ) 87m Sr reactions from threshold to 15 MeV: possibility of production of 85 Sr at a low-energy accelerator
Excitation functions of the reactions 85 Rb( p,n ) 85m Sr, 85 Rb( p,n ) 85m,g Sr and 87 Rb( p,n ) 87m Sr were measured using the activation technique in the proton energy range of 2–5 MeV with a low-energy Tandem Accelerator. Our new data sets, combined with those of Kastleiner et al. data obtained previously at FZJ using enriched target 85 Rb, provide complete excitation functions of the 85 Rb( p,n ) 85m Sr and 85 Rb( p,n ) 85m,g Sr reactions. The experimental data were reproduced well by a model calculation using the code TALYS-2.0 after selection of a few input parameters, confirming the reliability of the experimental data. In contrast, model calculations based on global parameters in the data library TENDL-2023 overestimated the cross sections by nearly a factor of two compared to TALYS-2.0. The isomeric cross-section ratio 85m Sr/ 85g Sr was experimentally determined from the measured activities at the end of bombardment (EOB) up to 5 MeV. Above 5 MeV, the isomer ratio was also derived from the cross sections reported by Kastleiner et al., extending the information upto 15 MeV. The trend was interpreted in terms of the reaction energy available and the effect of spin distribution of the level density. Finally, the 85 Rb( p,n ) 85 Sr reaction is demonstrated to be a promising route for the production of radionuclidically pure 85 Sr at a small cyclotron, possibly for medical applications.
- 18 March 2026
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 114 (6) , 423-431
Excitation functions of 85 Rb( p,n ) 85m,g Sr and 87 Rb( p,n ) 87m Sr reactions from threshold to 15 MeV: possibility of production of 85 Sr at a low-energy accelerator
Excitation functions of the reactions 85 Rb( p,n ) 85m Sr, 85 Rb( p,n ) 85m,g Sr and 87 Rb( p,n ) 87m Sr were measured using the activation technique in the proton energy range of 2–5 MeV with a low-energy Tandem Accelerator. Our new data sets, combined with those of Kastleiner et al. data obtained previously at FZJ using enriched target 85 Rb, provide complete excitation functions of the 85 Rb( p,n ) 85m Sr and 85 Rb( p,n ) 85m,g Sr reactions. The experimental data were reproduced well by a model calculation using the code TALYS-2.0 after selection of a few input parameters, confirming the reliability of the experimental data. In contrast, model calculations based on global parameters in the data library TENDL-2023 overestimated the cross sections by nearly a factor of two compared to TALYS-2.0. The isomeric cross-section ratio 85m Sr/ 85g Sr was experimentally determined from the measured activities at the end of bombardment (EOB) up to 5 MeV. Above 5 MeV, the isomer ratio was also derived from the cross sections reported by Kastleiner et al., extending the information upto 15 MeV. The trend was interpreted in terms of the reaction energy available and the effect of spin distribution of the level density. Finally, the 85 Rb( p,n ) 85 Sr reaction is demonstrated to be a promising route for the production of radionuclidically pure 85 Sr at a small cyclotron, possibly for medical applications.
- 2 September 2025
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 113 (12) , 945-952
Excitation functions of ( p,γ ) and ( p,n ) reactions on zinc up to 4 MeV
Proton-induced reaction cross sections for 64 Zn( p,γ ) 65 Ga, 67 Zn( p,γ ) 68 Ga, 70 Zn( p,n ) 70 Ga, and nat Zn( p,x ) 67 Ga were measured in the 2.0–4.0 MeV energy range at a 3 MV Tandem Accelerator, using the stacked-foil activation technique in combination with high resolution γ -ray spectrometry. The obtained results are comparable to literature data determined via prompt γ -counting and X-ray counting methods. The excitation functions of this work are reproduced well by a model calculation using the code TALYS with a few chosen input parameters. The data should be useful in astrophysical research as well as in production of radionuclides at a small medical cyclotron.
- 2 September 2025
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 113 (12) , 945-952
Excitation functions of ( p,γ ) and ( p,n ) reactions on zinc up to 4 MeV
Proton-induced reaction cross sections for 64 Zn( p,γ ) 65 Ga, 67 Zn( p,γ ) 68 Ga, 70 Zn( p,n ) 70 Ga, and nat Zn( p,x ) 67 Ga were measured in the 2.0–4.0 MeV energy range at a 3 MV Tandem Accelerator, using the stacked-foil activation technique in combination with high resolution γ -ray spectrometry. The obtained results are comparable to literature data determined via prompt γ -counting and X-ray counting methods. The excitation functions of this work are reproduced well by a model calculation using the code TALYS with a few chosen input parameters. The data should be useful in astrophysical research as well as in production of radionuclides at a small medical cyclotron.
- 1 July 2025
- Published by American Physical Society (APS) in Physical Review C
- Vol. 112 (1)
Excitation functions of and reactions up to 15 MeV- 1 July 2025
- Published by American Physical Society (APS) in Physical Review C
- Vol. 112 (1)
Excitation functions of and reactions up to 15 MeV- 19 November 2024
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 113 (2) , 89-98
Excitation functions of proton-induced nuclear reactions on titanium
Excitation functions of the natTi(p,x)43,44m,44g,46,47,48Sc and natTi(p,x)48V reactions were measured using stacked target activation from reaction thresholds up to 44.28 MeV. A wide energy range was achieved by irradiating several stacks with proton beams of energies 16.7 MeV, 27 MeV, and 44.5 MeV. Cross-section data were obtained from 15 to 25 MeV at the Lawrence Berkeley National Laboratory (LBNL) and from 14 to 44.28 MeV and 8–17 MeV at the Forschungszentrum Jülich (FZJ). Each set of measured data agrees well with each other in the overlapping energy regions. The cross sections were also calculated theoretically using the TALYS code, and the model calculations reproduced the experimental values well. Generally, the results obtained for proton-induced reactions using the global set of parameters, as expressed in the TENDL-2021 data library, are not satisfactory. Our measurements are valuable for resolving discrepancies in the existing data and providing insights into reaction mechanisms.
- 19 November 2024
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 113 (2) , 89-98
Excitation functions of proton-induced nuclear reactions on titanium
Excitation functions of the natTi(p,x)43,44m,44g,46,47,48Sc and natTi(p,x)48V reactions were measured using stacked target activation from reaction thresholds up to 44.28 MeV. A wide energy range was achieved by irradiating several stacks with proton beams of energies 16.7 MeV, 27 MeV, and 44.5 MeV. Cross-section data were obtained from 15 to 25 MeV at the Lawrence Berkeley National Laboratory (LBNL) and from 14 to 44.28 MeV and 8–17 MeV at the Forschungszentrum Jülich (FZJ). Each set of measured data agrees well with each other in the overlapping energy regions. The cross sections were also calculated theoretically using the TALYS code, and the model calculations reproduced the experimental values well. Generally, the results obtained for proton-induced reactions using the global set of parameters, as expressed in the TENDL-2021 data library, are not satisfactory. Our measurements are valuable for resolving discrepancies in the existing data and providing insights into reaction mechanisms.
- 12 January 2024
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 112 (3) , 141-147
Activation cross sections for the formation of 51Cr and 52,54Mn in interactions of deuterons with iron
Excitation functions for the formation of the radionuclides 51Cr, 52Mn and 54Mn via deuteron-induced activation of natural iron were measured up to deuteron energies of 35 MeV. The available experimental databases of the reaction products 51Cr, 52Mn and 54Mn were extended and compared with the nuclear model calculations using the TALYS code. The model calculations reproduce our measured data after a careful choice of the input model parameters. Some information obtained on competition between the emission of multinucleons and a bound α-particle.
- 12 January 2024
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 112 (3) , 141-147
Activation cross sections for the formation of 51Cr and 52,54Mn in interactions of deuterons with iron
Excitation functions for the formation of the radionuclides 51Cr, 52Mn and 54Mn via deuteron-induced activation of natural iron were measured up to deuteron energies of 35 MeV. The available experimental databases of the reaction products 51Cr, 52Mn and 54Mn were extended and compared with the nuclear model calculations using the TALYS code. The model calculations reproduce our measured data after a careful choice of the input model parameters. Some information obtained on competition between the emission of multinucleons and a bound α-particle.
- 21 April 2022
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 110 (6-9) , 663-674
An overview of activation cross-section measurements of some neutron and charged-particle induced reactions in Bangladesh
Over the last several decades, our research group has been working on nuclear data measurements using a J-25 Neutron Generator, a TRIGA Mark II Research Reactor and a Tandem Accelerator at Savar, as well as an Am/Be neutron source at Rajshahi. The spectrum of fast neutrons having energies from 0.5 to 20 MeV in the core of the TRIGA reactor as well as from 1.5 to 11 MeV of the Am/Be source was well characterized for validation of evaluated data of neutron threshold reactions. Spectrum-averaged cross sections were determined by integral measurements. The integral values measured at both the reactor and the Am/Be source were compared with the integrated data deduced from measured and evaluated excitation functions of some nuclear reactions given in some data libraries. As example, the details on the integral and integrated cross sections of the 64Zn(n,p)64Cu and 60Ni(n,p)60Co reactions are discussed. In both cases, integral test shows that further improvement of the evaluated excitation function reported in data libraries is needed. The use of a newly developed facility at the 3 MV Tandem Accelerator in measurement of proton induced reaction cross sections in the energy region below 5 MeV is outlined, and new results on the 64Ni(p,n)64Cu and natNi(p,x)61Cu processes below 3 MeV are discussed.
- 21 April 2022
- Published by Walter de Gruyter GmbH in Radiochimica Acta
- Vol. 110 (6-9) , 663-674
An overview of activation cross-section measurements of some neutron and charged-particle induced reactions in Bangladesh
Over the last several decades, our research group has been working on nuclear data measurements using a J-25 Neutron Generator, a TRIGA Mark II Research Reactor and a Tandem Accelerator at Savar, as well as an Am/Be neutron source at Rajshahi. The spectrum of fast neutrons having energies from 0.5 to 20 MeV in the core of the TRIGA reactor as well as from 1.5 to 11 MeV of the Am/Be source was well characterized for validation of evaluated data of neutron threshold reactions. Spectrum-averaged cross sections were determined by integral measurements. The integral values measured at both the reactor and the Am/Be source were compared with the integrated data deduced from measured and evaluated excitation functions of some nuclear reactions given in some data libraries. As example, the details on the integral and integrated cross sections of the 64Zn(n,p)64Cu and 60Ni(n,p)60Co reactions are discussed. In both cases, integral test shows that further improvement of the evaluated excitation function reported in data libraries is needed. The use of a newly developed facility at the 3 MV Tandem Accelerator in measurement of proton induced reaction cross sections in the energy region below 5 MeV is outlined, and new results on the 64Ni(p,n)64Cu and natNi(p,x)61Cu processes below 3 MeV are discussed.
- Open Access
Positron Emission Intensity in the Decay of 86gY for Use in Dosimetry Studies
The β+-emitting radionuclide 86gY (t1/2 = 14.7 h) forms a matched-pair with the β−-emitting therapeutic radionuclide 90Y (t1/2 = 2.7 d) for theranostic application in medicine. This approach demands a precise knowledge of the positron emission probability of the PET nuclide which was until recently rather uncertain for 86gY. In this work, an 86gY source of high radionuclidic purity was prepared and a direct measurement of the positron emission intensity per 100 decay of the parent (hereafter “positron emission intensity”) was performed using high-resolution HPGe detector γ-ray spectroscopy. The electron capture intensity was also determined as an additional check by measuring the Kα and Kβ X-rays of energies 14.1 and 15.8 keV, respectively, using a low energy HPGe detector. From those measurements, normalized values of 27.2 ± 2.0% for β+-emission and 72.8 ± 2.0% for EC were obtained. These results are in excellent agreement with values recently reported in the literature based on a detailed decay scheme study.
Open AccessPositron Emission Intensity in the Decay of 86gY for Use in Dosimetry Studies
The β+-emitting radionuclide 86gY (t1/2 = 14.7 h) forms a matched-pair with the β−-emitting therapeutic radionuclide 90Y (t1/2 = 2.7 d) for theranostic application in medicine. This approach demands a precise knowledge of the positron emission probability of the PET nuclide which was until recently rather uncertain for 86gY. In this work, an 86gY source of high radionuclidic purity was prepared and a direct measurement of the positron emission intensity per 100 decay of the parent (hereafter “positron emission intensity”) was performed using high-resolution HPGe detector γ-ray spectroscopy. The electron capture intensity was also determined as an additional check by measuring the Kα and Kβ X-rays of energies 14.1 and 15.8 keV, respectively, using a low energy HPGe detector. From those measurements, normalized values of 27.2 ± 2.0% for β+-emission and 72.8 ± 2.0% for EC were obtained. These results are in excellent agreement with values recently reported in the literature based on a detailed decay scheme study.