M. Jafar Hussain
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
M. Jafar Hussain has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Aqil Inam
Department of Metallurgy and Materials Engineering, University of the Punjab, Lahore, 54590, PAKISTAN
1 shared publicationFida Hussain
Department of Electrical Engineering, COMSATS University Islamabad, Islamabad-44000, Pakistan
1 shared publication- Ghazanfar Abbas
Clean Energy Research Lab (CERL), Department of Physics, COMSATS University Islamabad, Lahore Campus, Lahore 54000, Pakistan
1 shared publication - Hafiz Qasim Ali
Aerospace Engineering Department, College of Aeronautical Engineering National University of Sciences and Technology (NUST) Islamabad Pakistan
1 shared publication M. Ashfaq Ahmad
Department of Physics, COMSATS University Islamabad, Lahore Campus, Lahore-54000, Pakistan
1 shared publication- Mohsin Ali Raza
Institute of Metallurgy & Materials Engineering, Faculty of Chemical & Materials Engineering, University of the Punjab, Lahore 54590, Pakistan
1 shared publication
Latest Publications
- 1 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (11) , 115303
Mechanical properties of graphene oxide coated-glass fiber reinforced unsaturated polyester composites
Glass fiber/unsaturated polyester (GF/UPE) composites have widespread utilization in aerospace, construction, sports, electronics and automobile applications due to their light weight, high strength and chemical resistance. This work aims to study the effect of graphene oxide (GO) coated-GF on the mechanical properties of GF/UPE composites. Woven GF mats were soaked in GO/ethanol suspension followed by vacuum drying to coat GO on glass fibers. GO coated-GF/UPE composites were prepared by hand layup technique followed by curing under compression. GO was also dispersed in UPE resin at 0.25 wt. % to develop dispersion strengthened UPE composite for comparison. Fourier transform infrared spectroscopy (FTIR) and energy dispersive x-ray analysis confirmed successful deposition of GO onto GF. Mechanical tests of composites such as tensile, bend and impact tests were carried out to study mechanical properties of the composites. Mechanical properties of GO coated-GF/UPE composites were found better than the uncoated GF/UPE and dispersion strengthened composites.
- 1 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (11) , 115303
Mechanical properties of graphene oxide coated-glass fiber reinforced unsaturated polyester composites
Glass fiber/unsaturated polyester (GF/UPE) composites have widespread utilization in aerospace, construction, sports, electronics and automobile applications due to their light weight, high strength and chemical resistance. This work aims to study the effect of graphene oxide (GO) coated-GF on the mechanical properties of GF/UPE composites. Woven GF mats were soaked in GO/ethanol suspension followed by vacuum drying to coat GO on glass fibers. GO coated-GF/UPE composites were prepared by hand layup technique followed by curing under compression. GO was also dispersed in UPE resin at 0.25 wt. % to develop dispersion strengthened UPE composite for comparison. Fourier transform infrared spectroscopy (FTIR) and energy dispersive x-ray analysis confirmed successful deposition of GO onto GF. Mechanical tests of composites such as tensile, bend and impact tests were carried out to study mechanical properties of the composites. Mechanical properties of GO coated-GF/UPE composites were found better than the uncoated GF/UPE and dispersion strengthened composites.
- 10 February 2019
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics B
- Vol. 33 (04) , 1950001
A modeling approach for low-temperature SOFC-based micro-combined heat and power systems
The world’s challenge is to determine a more efficient, economical and environmental-friendly energy source to compete and replace the ongoing conventional energy resources. Solid oxide fuel cells (SOFCs) provide a highly efficient system to use divergent energy resources and have proved to provide the cleanest energy, least energy use, and lowest emissions. A techno-economic study is required to investigate the model design for SOFC-based micro-combined heat and power (m-CHP) systems for applications in terms of educational and commercial buildings. This work models and explores the optimized application of hydrogen gas-fueled SOFC-based m-CHP systems in educational buildings. Two educational departments’ loads are presented and model of SOFC-based m-CHP system against the different electric power demands is performed, in order to provide a techno-economic assessment of the technology. For successful development of the technology, results are related to system rightsizing, operating strategies, thermal to electric ratios, and match between end-use, with an aim towards classifying the overall feasibility and essential application requirements.
- 10 February 2019
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics B
- Vol. 33 (04) , 1950001
A modeling approach for low-temperature SOFC-based micro-combined heat and power systems
The world’s challenge is to determine a more efficient, economical and environmental-friendly energy source to compete and replace the ongoing conventional energy resources. Solid oxide fuel cells (SOFCs) provide a highly efficient system to use divergent energy resources and have proved to provide the cleanest energy, least energy use, and lowest emissions. A techno-economic study is required to investigate the model design for SOFC-based micro-combined heat and power (m-CHP) systems for applications in terms of educational and commercial buildings. This work models and explores the optimized application of hydrogen gas-fueled SOFC-based m-CHP systems in educational buildings. Two educational departments’ loads are presented and model of SOFC-based m-CHP system against the different electric power demands is performed, in order to provide a techno-economic assessment of the technology. For successful development of the technology, results are related to system rightsizing, operating strategies, thermal to electric ratios, and match between end-use, with an aim towards classifying the overall feasibility and essential application requirements.