Amir Hussain Idrisi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Amir Hussain Idrisi has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Abdel Hamid Ismail Mourad
United Arab Emirates University
6 shared publications Abdel-Hamid Ismail Mourad
United Arab Emirates University,Department of Mechanical Engineering,Al Ain,United Arab Emirates
4 shared publications- Dinu Thomas Thekkuden
Mechanical and Industrial Engineering Department, Abu Dhabi University, Abu Dhabi 59911, United Arab Emirates
4 shared publications John Victor Christy
United Arab Emirates University,Department of Mechanical Engineering,Al-Ain,UAE,PO. Box 15551
4 shared publicationsAbdel-Hamid I. Mourad
3 shared publicationsAbdel Hamid Ismail Mourad
United Arab Emirates University,Department of Mechanical Engineering,Al-Ain,UAE,PO. Box 15551
2 shared publications
Latest Publications
- Open Access
- 10 October 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (10) , 1245
Editorial for the Special Issue on Nanomaterials for Micro/Nanodevices
The Special Issue of Micromachines, titled “Nanomaterials for Micro/Nanodevices”, comprehensively examines the intersection of nanotechnology and micro/nanodevices
- 10 October 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (10) , 1245
Open AccessEditorial for the Special Issue on Nanomaterials for Micro/Nanodevices
The Special Issue of Micromachines, titled “Nanomaterials for Micro/Nanodevices”, comprehensively examines the intersection of nanotechnology and micro/nanodevices
- Open Access
- 5 February 2024
- Published by Elsevier in Polymer Testing
- Vol. 132
Experimental investigation of long-term performance of fiber-reinforced epoxy and polyurethane polymer composites
- 5 February 2024
- Published by Elsevier in Polymer Testing
- Vol. 132
Open AccessExperimental investigation of long-term performance of fiber-reinforced epoxy and polyurethane polymer composites
- Open Access
Utilization of Mechanically Recycled Carbon Fibers in Vinyl Ester Composites
As we enter the twenty-first century, the aviation sector is expected to thrive as flying becomes the primary mode of transportation between states or nations. With such a demand, there is a corresponding need to manufacture aircraft components. The study focused on recycling carbon fiber composites received from the STRATA company, which were cut-off/waste material generated during the manufacture of airplane components. The cut-offs were then reduced to powder form using a standard face milling machine in three sizes (90, 150, and 250 µm). After, the powder was utilized to fabricate vinyl ester composites with four weight percentages (10%, 20%, 30%, and 40%). The results demonstrate that the tensile strength of all composites had risen by 30.2%, 21.3%, and 17.6% for 90, 150, and 250 µm respective with the addition of 20 wt% of reinforcement. Furthermore, subsequently decreased with the additional reinforcement for all particle sizes. The compressive strength increased by 30% from 187.5 MPa to 244 MPa with 10 wt% of recycled carbon powder composite of 90μm particle size. However, samples prepared with 150 μm and 250 μm fiber size show approximately 17% and 1% increase in the compression strength with the addition of 10wt% of recycled carbon powder. A similar trend was observed for the flexural strength with an highest increase of 9% for 90 µm particle size with addition of 20 wt% reinforcement. Nonetheless, the SEM images revealed that the fiber–matrix bonding was weak, proved through the clean pullout fibers at the fracture surfaces.
Open AccessUtilization of Mechanically Recycled Carbon Fibers in Vinyl Ester Composites
As we enter the twenty-first century, the aviation sector is expected to thrive as flying becomes the primary mode of transportation between states or nations. With such a demand, there is a corresponding need to manufacture aircraft components. The study focused on recycling carbon fiber composites received from the STRATA company, which were cut-off/waste material generated during the manufacture of airplane components. The cut-offs were then reduced to powder form using a standard face milling machine in three sizes (90, 150, and 250 µm). After, the powder was utilized to fabricate vinyl ester composites with four weight percentages (10%, 20%, 30%, and 40%). The results demonstrate that the tensile strength of all composites had risen by 30.2%, 21.3%, and 17.6% for 90, 150, and 250 µm respective with the addition of 20 wt% of reinforcement. Furthermore, subsequently decreased with the additional reinforcement for all particle sizes. The compressive strength increased by 30% from 187.5 MPa to 244 MPa with 10 wt% of recycled carbon powder composite of 90μm particle size. However, samples prepared with 150 μm and 250 μm fiber size show approximately 17% and 1% increase in the compression strength with the addition of 10wt% of recycled carbon powder. A similar trend was observed for the flexural strength with an highest increase of 9% for 90 µm particle size with addition of 20 wt% reinforcement. Nonetheless, the SEM images revealed that the fiber–matrix bonding was weak, proved through the clean pullout fibers at the fracture surfaces.
- 1 June 2020
- Published by Elsevier in Polymer Testing
- Vol. 86
Damage assessment of nanofiller-reinforced woven kevlar KM2plus/Epoxy resin laminated composites
- 1 June 2020
- Published by Elsevier in Polymer Testing
- Vol. 86
Damage assessment of nanofiller-reinforced woven kevlar KM2plus/Epoxy resin laminated composites
- 1 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
LabView based Conrol System Design for VTOL Aircraft System
Vertical Take Off and Landing (VTOL) aircraft system is a highly complicated, nonlinear, and a multi variable large disturbances system. Hence an efficient control mechanism is a difficult task for such system. The key objective of this study is to design a controller which balances the VTOL system parallel to the ground (horizontal position) in spite of disturbances. Design of Proportional Integral Derivative (PID) Controller is chosen because of its simplicity, clear functionality and easy to apply algorithm. This appears to be intuitive but can be hard in practice if multiple objectives such as high stability and reduced oscillations are to be achieved. The system response is examined for various values of controller gains. Also, setpoint filters are introduced to improve the overall performance of the controller. Finally, the experimental and LabVIEW based simulation results for pitch angle and current response (current flowing through motor) are calculated and compared which demonstrate that a proper filter selection based PID controller is an effective algorithm.
- 1 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
LabView based Conrol System Design for VTOL Aircraft System
Vertical Take Off and Landing (VTOL) aircraft system is a highly complicated, nonlinear, and a multi variable large disturbances system. Hence an efficient control mechanism is a difficult task for such system. The key objective of this study is to design a controller which balances the VTOL system parallel to the ground (horizontal position) in spite of disturbances. Design of Proportional Integral Derivative (PID) Controller is chosen because of its simplicity, clear functionality and easy to apply algorithm. This appears to be intuitive but can be hard in practice if multiple objectives such as high stability and reduced oscillations are to be achieved. The system response is examined for various values of controller gains. Also, setpoint filters are introduced to improve the overall performance of the controller. Finally, the experimental and LabVIEW based simulation results for pitch angle and current response (current flowing through motor) are calculated and compared which demonstrate that a proper filter selection based PID controller is an effective algorithm.
- 1 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Experimental Investigation of Syngas Production through Gasification of Biomass Char in a Fluidized Bed Reactor
This work deals with the gasification of the biomass char in a fixed bed gasifier and ultimately the production of syngas. Gasification of biomass is an endothermal process of thermal conversion that transforms solid fuel into gas. A limited supply of air serves as the oxidizing agent. The resultant gas consists of Carbon dioxide and monoxide, hydrogen, methane; minimal quantities of higher levels of hydrocarbons, nitrogen, oxygen, contaminating agents, including small chips, tars, ash etc. The hydrogen gas thus produced is a future fuel since this is a renewable energy source and acts as an alternative fuel. The syngas produced has many applications in the present scenario. The biomass air-steam gasification properties in a fluidized bed have been investigated in this paper. A number of experiments were conducted to study the effects on gas composition, gas emission, vapor decomposition and low heating (LHV) from reactor temperature, vapor to biomass ratio (S / B) and biomass particle size. The fuel gas production ranged from 1.43 to 2.57 Nm3/kg of biomass and the LHV of the fuel gas between 170.1 and 7772.95 kJ/Nm3. The results show that hydrogen production was driven by a higher temperature. A smaller particle has also been shown to be more favorable for higher LHV gas and yields.
- 1 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Experimental Investigation of Syngas Production through Gasification of Biomass Char in a Fluidized Bed Reactor
This work deals with the gasification of the biomass char in a fixed bed gasifier and ultimately the production of syngas. Gasification of biomass is an endothermal process of thermal conversion that transforms solid fuel into gas. A limited supply of air serves as the oxidizing agent. The resultant gas consists of Carbon dioxide and monoxide, hydrogen, methane; minimal quantities of higher levels of hydrocarbons, nitrogen, oxygen, contaminating agents, including small chips, tars, ash etc. The hydrogen gas thus produced is a future fuel since this is a renewable energy source and acts as an alternative fuel. The syngas produced has many applications in the present scenario. The biomass air-steam gasification properties in a fluidized bed have been investigated in this paper. A number of experiments were conducted to study the effects on gas composition, gas emission, vapor decomposition and low heating (LHV) from reactor temperature, vapor to biomass ratio (S / B) and biomass particle size. The fuel gas production ranged from 1.43 to 2.57 Nm3/kg of biomass and the LHV of the fuel gas between 170.1 and 7772.95 kJ/Nm3. The results show that hydrogen production was driven by a higher temperature. A smaller particle has also been shown to be more favorable for higher LHV gas and yields.
- 22 November 2019
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series C
- Vol. 101 (2) , 415-427
Evolution of Renewable Energy in India: Wind and Solar
- 22 November 2019
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series C
- Vol. 101 (2) , 415-427
Evolution of Renewable Energy in India: Wind and Solar
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Impact of the harsh environment on GFRE and GFRPol composite
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Impact of the harsh environment on GFRE and GFRPol composite
- Top Cited Papers
- 1 October 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 805, 502-508
Conventional stir casting versus ultrasonic assisted stir casting process: Mechanical and physical characteristics of AMCs
- 1 October 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 805, 502-508
Top Cited PapersConventional stir casting versus ultrasonic assisted stir casting process: Mechanical and physical characteristics of AMCs
- 13 September 2019
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 50 (11) , 5395-5409
Wear Performance Analysis of Aluminum Matrix Composites and Optimization of Process Parameters Using Statistical Techniques
- 13 September 2019
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 50 (11) , 5395-5409
Wear Performance Analysis of Aluminum Matrix Composites and Optimization of Process Parameters Using Statistical Techniques