Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jhonny de Sá Rodrigues has a total of 43 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of the Room and Cooling Channel Temperatures in Injection Molding: 3D Transient Heat Transfer Analysis

    by Hugo Miguel Silva, Filipe G. A. Silva, Jhonny de Sá Rodrigues, Justino Cruz, Augusto Rego

    This study develops analytical models to predict transient temperature distributions in injection molds. Three-dimensional transient thermal simulations were performed using the Finite Element Method (FEM) in ANSYS Workbench 2025 R1. Numerical results were used to provide analytical models through symbolic regression using Eureqa (Version 0.98 bet). Mesh convergence analysis was conducted to assess the reliability of the numerical solution. The analytical expressions relate the average part temperature to ambient temperature and cooling channel temperature. Validation against FEM results shows strong agreement between the analytical and numerical models, with low relative errors. The proposed approach allows temperature prediction and provides a computationally efficient method for thermal analysis in injection molding.

  • Open Access

    Analytical Models for the Prediction of Temperatures in Injection Molds: 2D Transient Heat Transfer Analysis

    by Hugo Miguel Silva, Justino Cruz, Filipe Silva, Jhonny de Sá Rodrigues, Augusto Rego

    This study investigates the influence of geometric scaling on transient heat transfer in injection molds using a two-dimensional finite element model. Transient thermal simulations were performed in ANSYS Mechanical APDL 2025 r1to evaluate the temperature evolution of the injected part during the cooling phase for multiple uniform scaling factors. The numerical results were processed using symbolic regression in Eureqa (Version 0.98 bet) to derive analytical models describing the temporal evolution of the average part temperature. Well-defined linear relationships were identified between model dimensions and thermal response across the analyzed scaling range. The proposed analytical models show excellent agreement with finite element results, with errors consistently below 1%. These results demonstrate that geometric scaling laws can be used to reliably estimate thermal behavior in injection molds of different sizes without the need for exhaustive numerical simulations, providing a computationally efficient approach for early-stage thermal analysis and model-based prediction in injection molding applications.

  • Smart Textiles for Body Thermo-Regulation: A Brief Systematic Review for Defence Applications

    by Inês Gonçalves, Paulo Teixeira Gonçalves, Susana P. B. Sousa, Tania V. Pinto, Jhonny Rodrigues

  • Open Access

    Electrical and Thermal Characterisation of Inkjet-Printed Conductive Materials for Structure-Integrated CubeSat Antenna Applications

    by Filipa Ribeiro, Daniel Gomes, João Ventura, Jhonny de Sá Rodrigues, Carlos Callaty, Andreia Araújo

    The development of multifunctional and lightweight materials is increasingly shaping the design of next-generation sensing and communication systems for space applications. In CubeSat platforms, severe constraints on mass, volume, and structural complexity motivate the integration of antenna functionalities directly onto load-bearing structures. In this context, printed electronics, particularly inkjet-printed conductive materials, offer new opportunities for creating adaptive, flexible, and structure-integrated devices that support both sensing and communication functionalities. This work investigates the electrical performance of inkjet-printed conductive materials for structure-integrated patch antennas. Two silver-based inks and one carbon-based ink were deposited on fiberglass-reinforced epoxy substrates and electrically characterized over a temperature range from −20 °C to 50 °C, representative of CubeSat operational conditions. The silver-based inks exhibited electrical conductivities in the range of 106 S/m with limited variation (1 S/m, even after multilayer deposition, indicating insufficient performance for this application. Based on these results, the best-performing silver ink was selected to fabricate a proof-of-concept patch antenna directly on an S2-glass/epoxy structural substrate. The proposed approach demonstrates the feasibility of integrating conductive inkjet-printed layers onto composite structural substrates intended for future structure-integrated antenna applications in CubeSat platforms, offering a pathway toward mass-efficient, low-profile, and highly integrated communication structures.

  • Open Access

    Influence of Geometric Scaling on the Stiffness and Stress Behavior of a Robotic Gripper

    by Hugo Miguel Silva, Jhonny Rodrigues, Justino Cruz, Filipe Silva, Augusto Rego

    Robotic grippers play a key role in industrial automation and precision manipulation, where structural stiffness critically influences performance, load capacity, and accuracy. This study investigates how variations in geometric dimensions affect the stiffness and stresses of the gripper, thereby supporting more informed design decisions. A three-dimensional baseline model of a parallel-jaw robotic gripper was developed and systematically scaled along the three principal axes to evaluate the independent effects of geometric variation. Numerical simulations were conducted using ANSYS Workbench 2025 R1 to evaluate the stiffness and stress responses resulting from geometric scaling. The results provide insight into how scaling strategies influence mechanical behavior, offering a foundation for the optimization of gripper geometry in future designs.

  • Open Access

    Mechanical assessment of composite laminates reinforced with recycled fibreglass and polymeric particles

    by J.M.A. Picado, R.D.S.G. Campilho, R.F.R. Pinto, J.S. Rodrigues

    Recycling composite materials presents a viable solution to reduce waste and promote sustainability, yet challenges remain in maintaining mechanical performance and feasibility for reuse. This study evaluates the strength of recycled composite materials and experimentally investigates their feasibility. Composite plates were produced using thermoset resin reinforced with fibreglass, with variations incorporating recycled fibreglass scraps and polymeric particles from automotive components. Mechanical characterisation was conducted through tensile, shear, mode I and mode II fracture tests, to assess their structural integrity. Results demonstrated that the plate containing fibreglass particles, from recycled sources, exhibited the most favourable balance between mechanical properties and cost-effectiveness. A case study on a wind turbine blade reinforced the potential of recycled composites for industrial applications, highlighting fibreglass fibre reinforcement as the most promising option from a sustainability perspective. Among the recycled reinforcements investigated, reclaimed fibreglass particles provided superior tensile modulus and strength compared to PA and PP particles owing to the intrinsically high stiffness and strength of fibreglass, even in discontinuous form coupled with the preserved silane sizing that ensures strong interfacial bonding with the epoxy matrix. These findings contribute to the advancement of composite recycling strategies, promoting the circular economy while maintaining material performance for structural applications.

  • Open Access

    Heat Conduction Control Using Deep Q-Learning Approach with Physics-Informed Neural Networks

    by Nelson D. Gonçalves, Jhonny de Sá Rodrigues

    As modern systems become more complex, their control strategy no longer relies only on measurement data from probes; it also requires information from mathematical models for non-measurable places. On the other hand, those mathematical models can lead to unbearable computation times due to their own complexity, making the control process non-viable. To overcome this problem, it is possible to implement any kind of surrogate model that enables the computation of such estimates within an acceptable time frame, which allows for making decisions. Using a Physics-Informed Neural Network as a surrogate model, it is possible to compute the temperature distribution at each time step, replacing the need for running direct numerical simulations. This approach enables the use of a Deep Reinforcement Learning algorithm to train a control strategy. On this work, we considered a one-dimensional heat conduction problem, in which temperature distribution feeds a control system. Such control system has the objective of reacing and maintaining constant temperature value at a specific location of the 1D problem by activating a heat source; the desired location somehow cannot be directly measured so, the PINN approach allows to estimate its temperature with a minimum computational workload. With this approach, the control training becomes much faster without the need of performing numerical simulations or laboratory measurements.


  • Open Access

    Heat Conduction Control using Deep Q-Learning approach with Physics-Informed Neural Networks

    by N.D. Gonçalves, Jhonny de Sá Rodrigues

    As modern systems are becoming more complex their control strategy cannot longer relay only on measurement information that usually comes from probes but also from mathematical models. Those systems models can lead to unbearable computation times due to their own complexity, turning the control process non-viable, which leads to the implementation of surrogate models that enable to achieve estimates within acceptable time to take decisions. A control trained with Deep Reinforcement Learning algorithm, using a Physics-Informed Neural Network to obtain the temperature map on the following time step, replaces the need of running Direct Numerical Simulations. On this work we considered an 1D heat conduction problem, which temperature distribution feeds a control system to activate a heat source aiming to obtain a constant, previously defined, temperature value. With this approach, control training becomes much faster without the need of performing numerical simulations or laboratory measurements, as well the control is taken based on Neural Network enabling its implementation on simple processors to edge computing.

  • Fracture characterization of a bi‐material bonded aluminum/CFRP joints under mixed‐mode I + II loading

    by Raul D. F. Moreira, Marcelo F. S. F. de Moura, Filipe G. A. Silva, Jhonny S. Rodrigues, Fernando D. R. Silva

    Fracture characterization under mixed‐mode I + II loading of bi‐material bonded joints with aluminum–carbon fiber reinforced polymer (AL‐CFRP) adherends was analyzed in this work. Five different and quite simple fracture tests were employed aiming to cover properly the complete mixed‐mode I + II range and identifying a representative energy‐based fracture criterion. A mode partitioning method lying on cohesive zone analysis was implemented, enabling the identification of strain energy mode I and mode II components for each type of test, which is relevant regarding the estimation of the energy‐based criterion defining the fracture envelope of these bi‐material joints.