Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mariam Shakeel has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Combining Thermal Effect and Mobility Control Mechanism to Reduce Water Cut in a Sandstone Reservoir in Kazakhstan

    by Dilyara Sagandykova, Mariam Shakeel, Peyman Pourafshary

    The application of polymer flooding is currently under investigation to control water cut and recover residual oil from a giant sandstone reservoir in Kazakhstan, where the water cut in most producers exceeds 90%, leaving substantial untouched oil in the porous media. The primary objective of this research is to explore the feasibility of a novel approach that combines the mechanisms of mobility control by polymer injection and the thermal effects, such as oil viscosity reduction, by utilizing hot water to prepare the polymer solution. This innovative hybrid method’s impact on parameters like oil recovery, resistance factor, and mobility was measured and analyzed. The research involved an oil displacement study conducted by injecting a hot polymer at a temperature of 85 °C, which is higher than the reservoir temperature. Incremental recovery achieved through hot polymer injection was then compared to the recovery by conventional polymer flooding and the conventional surfactant–polymer-enhanced oil recovery techniques. The governing mechanisms behind recovery, including reductions in oil viscosity, alterations in polymer rheology, and effective mobility control, were systematically studied to comprehend the influence of this proposed approach on sweep efficiency. Given the substantial volume of residual oil within the studied reservoir, the primary objective is to improve the sweep efficiency as much as possible. Conventional polymer flooding demonstrated a moderate incremental oil recovery rate of approximately 48%. However, with the implementation of the new hybrid method, the recovery rate increased to more than 52%, reflecting a 4% improvement. Despite the polymer’s lower viscosity during hot polymer flooding, which was observed by the lower pressure drop in contrast to the conventional polymer flooding scenario, the recovery factor was higher. This discrepancy indicates that while polymer viscosity decreases, the activation of other oil displacement mechanisms contributes to higher oil production. Applying hybrid enhanced oil recovery mechanisms presents an opportunity to reduce project costs. For instance, achieving comparable results with lower chemical concentrations is of practical significance. The potential impact of this work on enhancing the profitability of chemically enhanced oil recovery within the sandstone reservoir under study is critical.


  • Open Access

    Maximizing oil recovery: Innovative chemical EOR solutions for residual oil mobilization in Kazakhstan's waterflooded sandstone oilfield

    by Mariam Shakeel, Dilyara Sagandykova, Aibek Mukhtarov, Amina Dauyltayeva, Laila Maratbekkyzy, Peyman Pourafshary, Darya Musharova


  • Open Access

    Screening of Chemicals to Enhance Oil Recovery in a Mature Sandstone Oilfield in Kazakhstan: Overcoming Challenges of High Residual Oil

    by Amina Dauyltayeva, Aibek Mukhtarov, Dilyara Sagandykova, Mariam Shakeel, Peyman Pourafshary, Darya Musharova

    Chemical flooding, such as alkaline-surfactant (AS) or nanoparticles-surfactant (NS) flooding, is an enhanced oil recovery (EOR) technique that has been increasingly utilized to enhance the oil production rate and recovery factor while reducing chemical adsorption. The AS/NS flooding process involves the injection of a mixture of surfactant and alkali/nanoparticles solutions into an oil reservoir to reduce the interfacial tension between the oil and water phases by surfactant and lower surfactant adsorption by alkali or nanoparticles (NPs) to improve the residual oil recovery. In this study, the AS/NS flooding is evaluated for a Kazakhstani oilfield by systematically screening the chemical constituents involved. Field A in Kazakhstan, one of the oldest fields in the country, has been waterflooded for decades and has not produced even 50% of the original oil in place (OOIP). Currently, the water cut of the field is more than 90%, with a high residual oil saturation. Therefore, besides polymer flooding to control mobility, chemical EOR is proposed as a tertiary recovery method to mobilize residual oil. This study aimed to screen chemicals, including surfactant, alkali, and NPs, to design an effective AS/NS flooding program for the target field. The study focused on conducting laboratory experiments to identify the most effective surfactant and further optimize its performance by screening suitable alkaline and NPs based on their compatibility, stability, and adsorption behavior under reservoir conditions. The performance of the screened chemicals in the porous media was analyzed by a set of coreflood experiments. The findings of the study indicated that alkali agents, particularly sodium carbonate, positively affected surfactant performance by reducing its adsorption by 9–21%. The most effective surfactant combination was found, which gave Winsor type III microemulsion and the lowest interfacial tension (IFT) of 0.2 mN/m. The coreflood tests were conducted with the screened surfactant, alkali, and NPs. Both AS and NS tests demonstrated high residual oil recovery and microemulsion production. However, NS flooding performed better as the incremental oil recovery by NS flooding was 5% higher than standalone surfactant flooding and 9% higher than AS flooding. The results of this screening study helped in designing an efficient chemical formulation to improve the remaining oil recovery from Field A. The findings of this study can be used to design EOR projects for oil fields similar to Field A.


  • Open Access

    Polymer Screening for Efficient Water Cut Reduction in a Sandstone Oilfield in Kazakhstan

    by Daniyar Yerniyazov, Madi Yesmukhambet, Razida Kenes, Azamat Bukayev, Mariam Shakeel, Peyman Pourafshary, Darya Musharova

    Polymer flooding is one of the most widely used and effective enhanced oil recovery techniques. It can improve the macroscopic sweep efficiency of a reservoir by controlling the fractional flow of water. The applicability of polymer flooding for one of the sandstone fields in Kazakhstan was evaluated in this study and polymer screening was carried out to choose the most appropriate polymer among four hydrolyzed polyacrylamide polymer samples. Polymer samples were prepared in Caspian seawater (CSW) and assessed based on rheology, thermal stability, sensitivity to non-ionic materials and oxygen, and static adsorption. All the tests were performed at a reservoir temperature of 63 °C. Based on the results of the screening study, tolerance of a polymer towards high-temperature reservoir conditions, resistance to bacterial activity and dissolved oxygen present in make-up brine, chemical degradation, and reduced adsorption on rock surface were considered the most important screening parameters. As a result of this screening study, one out of four polymers was selected for the target field as it showed a negligible effect of bacterial activity on thermal stability. The results of static adsorption also showed 13–14% lower adsorption of the selected polymer compared to other polymers tested in the study. The results of this study demonstrate important screening criteria to be followed during polymer selection for an oilfield as the polymer should be selected based on not only polymer characteristics but also the polymer interactions with the ionic and non-ionic components of the make-up brine.


  • Open Access

    Unlocking the Power of Artificial Intelligence: Accurate Zeta Potential Prediction Using Machine Learning

    by Rizwan Muneer, Muhammad Rehan Hashmet, Peyman Pourafshary, Mariam Shakeel

    Nanoparticles have gained significance in modern science due to their unique characteristics and diverse applications in various fields. Zeta potential is critical in assessing the stability of nanofluids and colloidal systems but measuring it can be time-consuming and challenging. The current research proposes the use of cutting-edge machine learning techniques, including multiple regression analyses (MRAs), support vector machines (SVM), and artificial neural networks (ANNs), to simulate the zeta potential of silica nanofluids and colloidal systems, while accounting for affecting parameters such as nanoparticle size, concentration, pH, temperature, brine salinity, monovalent ion type, and the presence of sand, limestone, or nano-sized fine particles. Zeta potential data from different literature sources were used to develop and train the models using machine learning techniques. Performance indicators were employed to evaluate the models’ predictive capabilities. The correlation coefficient (r) for the ANN, SVM, and MRA models was found to be 0.982, 0.997, and 0.68, respectively. The mean absolute percentage error for the ANN model was 5%, whereas, for the MRA and SVM models, it was greater than 25%. ANN models were more accurate than SVM and MRA models at predicting zeta potential, and the trained ANN model achieved an accuracy of over 97% in zeta potential predictions. ANN models are more accurate and faster at predicting zeta potential than conventional methods. The model developed in this research is the first ever to predict the zeta potential of silica nanofluids, dispersed kaolinite, sand–brine system, and coal dispersions considering several influencing parameters. This approach eliminates the need for time-consuming experimentation and provides a highly accurate and rapid prediction method with broad applications across different fields.


  • Open Access

    Optimization of Low Salinity Water/Surfactant Flooding Design for Oil-Wet Carbonate Reservoirs by Introducing a Negative Salinity Gradient

    by Mariam Shakeel, Aida Samanova, Peyman Pourafshary, Muhammad Rehan Hashmet

    Engineered water surfactant flooding (EWSF) is a novel EOR technique to reduce residual oil saturation; however, it becomes quite challenging to obtain Winsor Type III microemulsion and the lowest IFT under actual reservoir conditions if only low salinity water is used. The main objective of this study was to design a negative salinity gradient to optimize the performance of the hybrid method. Three corefloods were performed on carbonate outcrop samples. The injection sequence in the first test was conventional waterflooding followed by optimum engineered water injection (2900 ppm) and finally an EWSF stage. The second and third tests were conducted using a varying negative salinity gradient. Engineered water for this study was designed by 10 times dilution of Caspian Sea water and spiking with key active ions. A higher salinity gradient was used for the first negative salinity gradient test. A total of 4300 ppm brine with 1 wt% surfactant was injected as a pre-flush after waterflooding followed by a further reduced salinity brine (~1400 ppm). The second negative salinity gradient test consisted of three post-waterflooding injection stages with salinities of 4600, 3700, and 290 ppm, respectively. Up to 8% and 16% more incremental oil recovery after waterflooding was obtained in the second and third tests, respectively, as compared to the first test. The descending order of brine salinity helped to create an optimum salinity environment for the surfactant despite surfactant adsorption. This study provided an optimum design for a successful LSSF test by adjusting the brine salinity and creating a negative salinity gradient during surfactant flooding. A higher reduction in residual oil saturation can be achieved by carefully designing an LSSF test, improving project economics.


  • Open Access

    Hybrid surfactant-nanoparticles assisted CO2 foam flooding for improved foam stability: A review of principles and applications

    by Miras Issakhov, Mariam Shakeel, Peyman Pourafshary, Saule Aidarova, Altynay Sharipova