Maher Dammak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Maher Dammak has a total of 86 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed Kharrat
Laboratory of Electromechanical Systems, National School of Engineers of Sfax, University of Sfax, Sfax 3038, Tunisia
44 shared publications A. Shirazi-Adl
Division of Applied Mechanics, Department of Mechanical Engineering, Ecole Polytechnique, Montreal, Canada
4 shared publications- Florence Vacandio
Aix-Marseille University, CNRS, MADIREL UMR 7246, Marseille cedex 20, France
4 shared publications Hajer Ketata
Laboratory of Electromechanical Systems (LASEM), National Engineering School of Sfax, University of Sfax, 3038 Sfax, Tunisia
4 shared publications- Hajer Ketata
University of Sfax
4 shared publications Manel Zouari
Laboratory of Electromechanical Systems (LASEM), National Engineering School of Sfax, University of Sfax, Sfax, Tunisia
4 shared publications
Latest Publications
- 13 May 2025
- Published by Springer Nature
- p. 604-612
Morphological Characterization of Zn-Co Coatings: Effect of Additive and Baths’ Parameters
- 13 May 2025
- Published by Springer Nature
- p. 604-612
Morphological Characterization of Zn-Co Coatings: Effect of Additive and Baths’ Parameters
- 27 September 2024
- Published by Springer Nature
- p. 245-252
Tribological Study of Polymer-Metal Composite Coatings Deposited onto Organic Substrates
- 27 September 2024
- Published by Springer Nature
- p. 245-252
Tribological Study of Polymer-Metal Composite Coatings Deposited onto Organic Substrates
- 28 August 2024
- Published by Springer Nature
- p. 264-272
Tribological Properties of Linear Low Density Polyethylene Reinforced with Almond Shell Particles: Impact of NaOH Treatment
- 28 August 2024
- Published by Springer Nature
- p. 264-272
Tribological Properties of Linear Low Density Polyethylene Reinforced with Almond Shell Particles: Impact of NaOH Treatment
- 24 March 2024
- Published by Springer Nature
- p. 249-257
Structural Characterization of Electrodeposited Ni Coatings Filled with Graphite or MoS2 Particles
- 24 March 2024
- Published by Springer Nature
- p. 249-257
Structural Characterization of Electrodeposited Ni Coatings Filled with Graphite or MoS2 Particles
- 24 March 2024
- Published by Springer Nature
- p. 303-310
Tribological, Micromechanical and Structural Characterizations of PA66 Composites Filled Cu Micro-particles
- 24 March 2024
- Published by Springer Nature
- p. 303-310
Tribological, Micromechanical and Structural Characterizations of PA66 Composites Filled Cu Micro-particles
- 24 March 2024
- Published by Springer Nature
- p. 241-248
Morphological and Structural Characterization of Zn-Ni Electrodeposited Coatings: Effect of Sulfate Bath Parameters
- 24 March 2024
- Published by Springer Nature
- p. 241-248
Morphological and Structural Characterization of Zn-Ni Electrodeposited Coatings: Effect of Sulfate Bath Parameters
- Open Access
On the Structural, Thermal, Micromechanical and Tribological Characterizations of Cu-Filled Acrylonitrile Butadiene Styrene Micro-Composites
The purpose of this work was to investigate the structural, thermal, micromechanical and tribological properties of novel polymer/metal composite materials for bearing applications. Copper (Cu)-filled Acrylonitrile Butadiene Styrene (ABS) composites were mixed in a laboratory scale by an internal mixer with two blade impellers, and then injection-molded. Neat ABS, ABS+5wt% Cu, ABS+10wt% Cu, and ABS+15wt% Cu were the four materials that were tested. The dispersion of Cu particles in the ABS matrix was investigated using Scanning Electron Microscopy (SEM) and a micro-tomography scan. The filler particles have a uniform distribution in the matrix, according to the observations. The incorporation of Cu filler also refined an increase in the glass transition temperature from Differential Scanning Calorimetry (DSC) and less intensity in the amorphous phase by X-ray diffraction (XRD). Nanoindentation tests were carried out to characterize the micro-mechanical behavior of the composites. Friction and wear analysis were also examined using a pin-on-disk tribometer. Compared with neat ABS, all the micro-composites showed much higher indentation hardness, Vickers hardness, and indentation elastic modulus. It was also concluded that the incorporation of Cu filler into ABS simultaneously improved the friction and wear properties of the composites, which contributed to the suitability of the micro-filled composites with hard metallic particles for a wider range of mechanical components for bearing applications.
Open AccessOn the Structural, Thermal, Micromechanical and Tribological Characterizations of Cu-Filled Acrylonitrile Butadiene Styrene Micro-Composites
The purpose of this work was to investigate the structural, thermal, micromechanical and tribological properties of novel polymer/metal composite materials for bearing applications. Copper (Cu)-filled Acrylonitrile Butadiene Styrene (ABS) composites were mixed in a laboratory scale by an internal mixer with two blade impellers, and then injection-molded. Neat ABS, ABS+5wt% Cu, ABS+10wt% Cu, and ABS+15wt% Cu were the four materials that were tested. The dispersion of Cu particles in the ABS matrix was investigated using Scanning Electron Microscopy (SEM) and a micro-tomography scan. The filler particles have a uniform distribution in the matrix, according to the observations. The incorporation of Cu filler also refined an increase in the glass transition temperature from Differential Scanning Calorimetry (DSC) and less intensity in the amorphous phase by X-ray diffraction (XRD). Nanoindentation tests were carried out to characterize the micro-mechanical behavior of the composites. Friction and wear analysis were also examined using a pin-on-disk tribometer. Compared with neat ABS, all the micro-composites showed much higher indentation hardness, Vickers hardness, and indentation elastic modulus. It was also concluded that the incorporation of Cu filler into ABS simultaneously improved the friction and wear properties of the composites, which contributed to the suitability of the micro-filled composites with hard metallic particles for a wider range of mechanical components for bearing applications.
- 13 September 2023
- Published by Springer Nature
- p. 12-20
Implant Shape and Modeling Approaches Effects on the Biomechanical Tibia-Bone Response
- 13 September 2023
- Published by Springer Nature
- p. 12-20
Implant Shape and Modeling Approaches Effects on the Biomechanical Tibia-Bone Response