Dmitriy Topolsky
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dmitriy Topolsky has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Nikita Topolskiy
School of Electrical Engineering and Computer Science, South Ural State University (national research university), Chelyabinsk, Russia
8 shared publications - Evgenii Viktorovich Solomin
Department of Electric Power Generation Stations, Network and Supply-Systems, South Ural State University (National Research University), Chelyabinsk 454080, Russia
6 shared publications I.G. Topolskaya
Theoretical Basics of Electrical Engineering, South Ural State University (national research university),Chelyabinsk,Russia
6 shared publicationsS. P. Gladyshev
University of Michigan
4 shared publications- Elena Zvereva
Тюменский индустриальный университет, ф-л в Нижневартовске
3 shared publications I. G. Topolskaya
Polytechnic Institute, Power Engineering Faculty, South Ural State University (national research university), Chelyabinsk, Russia
3 shared publications
Latest Publications
- Open Access
- 1 August 2024
- Published by FSAEIHE South Ural State University (National Research University) in Bulletin of the South Ural State University. Ser. Computer Technologies, Automatic Control & Radioelectronics
- Vol. 24 (3) , 5-15
Development of a digital twin of the control system test bench for digital instrument transformers
The presented work considers the option of implementing a digital twin of a test bench control system for digital instrument transformers using a universal SCADA system. The basis of the design of the test bench is a hydraulic servo drive using hydrostatic guides. Digital instrument transformers must have a service life of at least 25 years, a verification interval of 8 years or more. To achieve such high performance characteristics, a large number of tests are required for such products. In particular, to check the reliability of operation of this class of devices, it is necessary to conduct tests on a diagnostic vibration stand. The task of creating test benches based on a hydraulic servo drive using hydrostatic guides is an urgent scientific and technical task. The architecture of a digital twin of the test bench control system has been developed. To test the functionality of the application, a simulation of the operation of a digital twin of the control system of a test bench for digital instrument transformers was performed. Aim. Based on an analysis of the operating modes of the test bench and options for implementing digital twins, develop a prototype of a test bench control system for digital instrument transformers using a universal SCADA system. Materials and methods. The posed scientific problems were solved using key methods of digitalization of production, computer and simulation modeling of the interaction of the digital twin with elements of the test bench control system. Results. The main practical result of the research is the development of a digital twin of the test bench control system for digital instrument transformers. It is proposed to use the domestic universal SCADA system when implementing the digital twin in software. Conclusion. Analysis of options for implementing a digital twin showed that the use of universal SCADA systems simplifies the development process. Such software systems provide the ability to control automated technological processes, collect and process data in real time, monitor the condition of equipment and the progress of production processes, as well as quickly respond to any problems. When developing a digital twin, the use of a universal SCADA system is justified. Prototyping of the test bench control system was carried out using a universal domestic SCADA system. An OPC server has been developed for data exchange with a microcontroller of the STM32 family in the Modbus Universal MasterOPC application and a project in the MasterSCADA system. Testing of the application showed the full functionality of the developed project.
- 1 August 2024
- Published by FSAEIHE South Ural State University (National Research University) in Bulletin of the South Ural State University. Ser. Computer Technologies, Automatic Control & Radioelectronics
- Vol. 24 (3) , 5-15
Open AccessDevelopment of a digital twin of the control system test bench for digital instrument transformers
The presented work considers the option of implementing a digital twin of a test bench control system for digital instrument transformers using a universal SCADA system. The basis of the design of the test bench is a hydraulic servo drive using hydrostatic guides. Digital instrument transformers must have a service life of at least 25 years, a verification interval of 8 years or more. To achieve such high performance characteristics, a large number of tests are required for such products. In particular, to check the reliability of operation of this class of devices, it is necessary to conduct tests on a diagnostic vibration stand. The task of creating test benches based on a hydraulic servo drive using hydrostatic guides is an urgent scientific and technical task. The architecture of a digital twin of the test bench control system has been developed. To test the functionality of the application, a simulation of the operation of a digital twin of the control system of a test bench for digital instrument transformers was performed. Aim. Based on an analysis of the operating modes of the test bench and options for implementing digital twins, develop a prototype of a test bench control system for digital instrument transformers using a universal SCADA system. Materials and methods. The posed scientific problems were solved using key methods of digitalization of production, computer and simulation modeling of the interaction of the digital twin with elements of the test bench control system. Results. The main practical result of the research is the development of a digital twin of the test bench control system for digital instrument transformers. It is proposed to use the domestic universal SCADA system when implementing the digital twin in software. Conclusion. Analysis of options for implementing a digital twin showed that the use of universal SCADA systems simplifies the development process. Such software systems provide the ability to control automated technological processes, collect and process data in real time, monitor the condition of equipment and the progress of production processes, as well as quickly respond to any problems. When developing a digital twin, the use of a universal SCADA system is justified. Prototyping of the test bench control system was carried out using a universal domestic SCADA system. An OPC server has been developed for data exchange with a microcontroller of the STM32 family in the Modbus Universal MasterOPC application and a project in the MasterSCADA system. Testing of the application showed the full functionality of the developed project.
- Open Access
- 1 February 2024
- Published by FSAEIHE South Ural State University (National Research University) in Bulletin of the South Ural State University. Ser. Computer Technologies, Automatic Control & Radioelectronics
- Vol. 24 (1) , 19-31
Development of a software package for testing digital instrument transformers on a vibration stand
The presented work examines a software package for monitoring the condition of a hydraulic servo drive with hydrostatic guides as part of a diagnostic vibration stand for digital transformers. The service life of digital instrument transformers is 25 years, and the calibration interval is 8 years. To achieve such high performance characteristics, it is necessary to conduct a large number of tests for such products. One such test is the vibration test. The uniqueness of the hydraulic drive used in the diagnostic vibration stand lies in its long service life under operational loads (up to 100 million cycles). This reliability is achieved with special hydrostatic guides in the hydraulic drive design and requires special software. The architecture of the software complex for the vibration stand has been created. To test the functionality of the package, simulation modeling of the operation of the components of the software package was performed. Aim. Based on the analysis of the functioning of technological equipment and options for implementing control software, develop the architecture of a software package for implementing a system for condition monitoring of a servo hydraulic drive with hydrostatic guides as part of a diagnostic vibration stand for digital transformers. Materials and methods. The stated scientific problems were solved using methods of system analysis, computer, mathematical and simulation modeling of the interaction of the software complex with the components of the servo hydraulic drive with hydrostatic guides. Results. The main practical result of the research is the development of the architecture of a software package for testing digital instrument transformers on a vibration stand. It is proposed to use cross-platform solutions when implementing the complex software and rely on modern experience in using freely distributed software. Conclusion. The developed architecture of the software package is focused on ensuring the automated operation of servo hydraulic drives, allows you to configure all the necessary equipment parameters, monitor the condition of the equipment using digital data transfer protocols, centrally save and replicate hydraulic drive settings for specific operating conditions on the enterprises. Analysis of implementation options showed that the use of a SCADA system simplifies the process of developing standard projects for dispatch control and data collection and condition monitoring, but at the same time, it has increased complexity at the stage of deployment and operation. The functionality of none of the widespread and reliable SCADA systems covers all the requirements for this project. This particularly applies to USB connectivity and high frequency signal processing required by design requirements. In addition, when using universal SCADA systems, the end user must purchase a license for the RunTime SCADA component.
- 1 February 2024
- Published by FSAEIHE South Ural State University (National Research University) in Bulletin of the South Ural State University. Ser. Computer Technologies, Automatic Control & Radioelectronics
- Vol. 24 (1) , 19-31
Open AccessDevelopment of a software package for testing digital instrument transformers on a vibration stand
The presented work examines a software package for monitoring the condition of a hydraulic servo drive with hydrostatic guides as part of a diagnostic vibration stand for digital transformers. The service life of digital instrument transformers is 25 years, and the calibration interval is 8 years. To achieve such high performance characteristics, it is necessary to conduct a large number of tests for such products. One such test is the vibration test. The uniqueness of the hydraulic drive used in the diagnostic vibration stand lies in its long service life under operational loads (up to 100 million cycles). This reliability is achieved with special hydrostatic guides in the hydraulic drive design and requires special software. The architecture of the software complex for the vibration stand has been created. To test the functionality of the package, simulation modeling of the operation of the components of the software package was performed. Aim. Based on the analysis of the functioning of technological equipment and options for implementing control software, develop the architecture of a software package for implementing a system for condition monitoring of a servo hydraulic drive with hydrostatic guides as part of a diagnostic vibration stand for digital transformers. Materials and methods. The stated scientific problems were solved using methods of system analysis, computer, mathematical and simulation modeling of the interaction of the software complex with the components of the servo hydraulic drive with hydrostatic guides. Results. The main practical result of the research is the development of the architecture of a software package for testing digital instrument transformers on a vibration stand. It is proposed to use cross-platform solutions when implementing the complex software and rely on modern experience in using freely distributed software. Conclusion. The developed architecture of the software package is focused on ensuring the automated operation of servo hydraulic drives, allows you to configure all the necessary equipment parameters, monitor the condition of the equipment using digital data transfer protocols, centrally save and replicate hydraulic drive settings for specific operating conditions on the enterprises. Analysis of implementation options showed that the use of a SCADA system simplifies the process of developing standard projects for dispatch control and data collection and condition monitoring, but at the same time, it has increased complexity at the stage of deployment and operation. The functionality of none of the widespread and reliable SCADA systems covers all the requirements for this project. This particularly applies to USB connectivity and high frequency signal processing required by design requirements. In addition, when using universal SCADA systems, the end user must purchase a license for the RunTime SCADA component.
- Open Access
- 1 January 2023
- Published by FSAEIHE South Ural State University (National Research University) in Bulletin of the South Ural State University. Ser. Computer Technologies, Automatic Control & Radioelectronics
- Vol. 24 (4) , 57-65
OPTIMIZATION OF THE CONTROL SYSTEM OF A SOFTWARE AND HARDWARE COMPLEX FOR ELECTRICITY ACCOUNTING
В представленной статье исследуется тема оптимизации системы управления программно-аппаратного комплекса для учета электроэнергии. Система управления играет решающую роль в точном измерении и контроле потребления электроэнергии. Основной целью данного исследования является выявление и внедрение методов оптимизации, которые повышают производительность и результативность системы управления. Цель исследования. На основе анализа существующих электротехнических комплексов разработать архитектуру, имитационные цифровые модели, алгоритмы эффективного управления и методику эксплуатации электротехнического комплекса на базе трехфазных цифровых измерительных трансформаторов с системой управления отечественного производства для учета электроэнергии в высоковольтных сетях переменного тока, обеспечивающих работоспособность и качество функционирования в различных режимах при разнообразных внешних воздействиях. Материалы и методы. Поставленные научные задачи решены с применением общей теории электротехнических комплексов и систем, теории автоматического управления, методов физического, математического, имитационного и компьютерного моделирования компонентов электротехнических комплексов и систем. Результаты. В статье отражено развитие общей теории электротехнических комплексов, включающих в себя цифровые комбинированные измерительные трансформаторы и систему управления в виде отдельно стоящего модуля объединения, в части оптимизации системных связей компонентов электротехнических комплексов учета электроэнергии. Предлагается повысить интеллектуальный уровень оконечного устройства для обеспечения возможности проведения первичного анализа данных ещё на первом уровне архитектуры системы учета электроэнергии. Заключение. Основным практическим результатом проведенных исследований является изготовление прототипа электротехнического комплекса на основе опытных образцов адаптивных цифровых трансформаторов тока и напряжения и системы управления электротехнического комплекса для учета электроэнергии на основе универсальной платформы для измерительных трансформаторов. Такое построение цифрового трехфазного измерительного трансформатора и универсальный оконечный блок (модуль объединения) позволяют на основе разработанного прототипа сравнительно просто разрабатывать аналогичные устройства с другими диапазонами токов и напряжений. В существующих комбинированных измерительных трансформаторах такое сочетание первичных преобразователей не используется.
- 1 January 2023
- Published by FSAEIHE South Ural State University (National Research University) in Bulletin of the South Ural State University. Ser. Computer Technologies, Automatic Control & Radioelectronics
- Vol. 24 (4) , 57-65
Open AccessOPTIMIZATION OF THE CONTROL SYSTEM OF A SOFTWARE AND HARDWARE COMPLEX FOR ELECTRICITY ACCOUNTING
В представленной статье исследуется тема оптимизации системы управления программно-аппаратного комплекса для учета электроэнергии. Система управления играет решающую роль в точном измерении и контроле потребления электроэнергии. Основной целью данного исследования является выявление и внедрение методов оптимизации, которые повышают производительность и результативность системы управления. Цель исследования. На основе анализа существующих электротехнических комплексов разработать архитектуру, имитационные цифровые модели, алгоритмы эффективного управления и методику эксплуатации электротехнического комплекса на базе трехфазных цифровых измерительных трансформаторов с системой управления отечественного производства для учета электроэнергии в высоковольтных сетях переменного тока, обеспечивающих работоспособность и качество функционирования в различных режимах при разнообразных внешних воздействиях. Материалы и методы. Поставленные научные задачи решены с применением общей теории электротехнических комплексов и систем, теории автоматического управления, методов физического, математического, имитационного и компьютерного моделирования компонентов электротехнических комплексов и систем. Результаты. В статье отражено развитие общей теории электротехнических комплексов, включающих в себя цифровые комбинированные измерительные трансформаторы и систему управления в виде отдельно стоящего модуля объединения, в части оптимизации системных связей компонентов электротехнических комплексов учета электроэнергии. Предлагается повысить интеллектуальный уровень оконечного устройства для обеспечения возможности проведения первичного анализа данных ещё на первом уровне архитектуры системы учета электроэнергии. Заключение. Основным практическим результатом проведенных исследований является изготовление прототипа электротехнического комплекса на основе опытных образцов адаптивных цифровых трансформаторов тока и напряжения и системы управления электротехнического комплекса для учета электроэнергии на основе универсальной платформы для измерительных трансформаторов. Такое построение цифрового трехфазного измерительного трансформатора и универсальный оконечный блок (модуль объединения) позволяют на основе разработанного прототипа сравнительно просто разрабатывать аналогичные устройства с другими диапазонами токов и напряжений. В существующих комбинированных измерительных трансформаторах такое сочетание первичных преобразователей не используется.
- Open Access
Development of a Mobile Robot for Mine Exploration
This study focuses on aspects specific to adaptive mobile robotic systems. These include providing flexibility, high performance, the use of widely available element bases and others. The science intensity and technical level of the development of mobile robots are constantly growing. The element base of robots is constantly updated. In the presented article, the direction of research is related to the problems specific to mining robots. The use of research robots makes it possible to ensure safety of work in hard-to-reach places, monitor the status of active and idle mines, and find new minerals in idle mines, the processing of which was previously impossible. The article discusses the issues of ensuring the versatility of the design, the need to miniaturize robots, reducing the cost of the robot while maintaining high performance, achieving the required level of protection from environmental influences in mines, and compatibility with control systems. Various ways of navigating robots in a limited space are analyzed. The results of the development and testing of a mobile robot prototype are presented. When looking for ways to implement a robot, the emphasis is on an effective combination of hardware and software.
Open AccessDevelopment of a Mobile Robot for Mine Exploration
This study focuses on aspects specific to adaptive mobile robotic systems. These include providing flexibility, high performance, the use of widely available element bases and others. The science intensity and technical level of the development of mobile robots are constantly growing. The element base of robots is constantly updated. In the presented article, the direction of research is related to the problems specific to mining robots. The use of research robots makes it possible to ensure safety of work in hard-to-reach places, monitor the status of active and idle mines, and find new minerals in idle mines, the processing of which was previously impossible. The article discusses the issues of ensuring the versatility of the design, the need to miniaturize robots, reducing the cost of the robot while maintaining high performance, achieving the required level of protection from environmental influences in mines, and compatibility with control systems. Various ways of navigating robots in a limited space are analyzed. The results of the development and testing of a mobile robot prototype are presented. When looking for ways to implement a robot, the emphasis is on an effective combination of hardware and software.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 0566-0570
Optimization of Functional Tasks for a Vision System of a Mobile Robot
This paper analyzes features of a computer vision of mobile robotic systems. One of the features of mobile robot vision systems is the limited computing resources. This is because, due to the requirements for cost and overall characteristics of the studied type of robots, their design uses relatively cheap computing devices with low speed and memory size. Therefore, it is necessary to simplify tasks that we set for the vision system, focusing on existing equipment. In addition, it is necessary to choose correct recognition algorithms for the vision system and adapt them for use in mobile versions of robotic systems. The paper discusses recognition algorithms in terms of requirements for vision systems of mobile robots. On the example of prototypes of mobile robots, optimal combinations of hardware and software solutions are shown, taking into account a simplification of functional tasks of vision systems. It is proposed to provide the requirements for computer vision systems under consideration by a rational combination of software and hardware capabilities.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 0566-0570
Optimization of Functional Tasks for a Vision System of a Mobile Robot
This paper analyzes features of a computer vision of mobile robotic systems. One of the features of mobile robot vision systems is the limited computing resources. This is because, due to the requirements for cost and overall characteristics of the studied type of robots, their design uses relatively cheap computing devices with low speed and memory size. Therefore, it is necessary to simplify tasks that we set for the vision system, focusing on existing equipment. In addition, it is necessary to choose correct recognition algorithms for the vision system and adapt them for use in mobile versions of robotic systems. The paper discusses recognition algorithms in terms of requirements for vision systems of mobile robots. On the example of prototypes of mobile robots, optimal combinations of hardware and software solutions are shown, taking into account a simplification of functional tasks of vision systems. It is proposed to provide the requirements for computer vision systems under consideration by a rational combination of software and hardware capabilities.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Digital Measurement System to Substation Automation Systems
This article deals with the research conducted in the field of smart electric power supply systems. The purpose of the research is to obtain significant scientific and technical results allowing us to proceed to the creation of new products and services for smart grids. The specific solution is a measurement system for digital substations with the highest voltage of 110 kV AC based on the open architecture concept. The study conducted a search and development of software and hardware solutions for the implementation of the measuring system of a digital substation using digital combined current and voltage transformers. The solution was based on TRATON-110 digital instrument transformers ensuring the voltage measurement accuracy class of 0.2 and the current measurement accuracy class of 0.2S. Software and equipment for technological support were also developed based on the open architecture concept for unifying the digital interface of current and voltage instrument transformers supported by the IEC 61850 protocols. This solution is based on the use of the Avacha universal digital signal processing board. The article highlights the results of complex testing of the measurement system components. The solutions obtained during the research are patented.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Digital Measurement System to Substation Automation Systems
This article deals with the research conducted in the field of smart electric power supply systems. The purpose of the research is to obtain significant scientific and technical results allowing us to proceed to the creation of new products and services for smart grids. The specific solution is a measurement system for digital substations with the highest voltage of 110 kV AC based on the open architecture concept. The study conducted a search and development of software and hardware solutions for the implementation of the measuring system of a digital substation using digital combined current and voltage transformers. The solution was based on TRATON-110 digital instrument transformers ensuring the voltage measurement accuracy class of 0.2 and the current measurement accuracy class of 0.2S. Software and equipment for technological support were also developed based on the open architecture concept for unifying the digital interface of current and voltage instrument transformers supported by the IEC 61850 protocols. This solution is based on the use of the Avacha universal digital signal processing board. The article highlights the results of complex testing of the measurement system components. The solutions obtained during the research are patented.
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 325-327
Dielectric Resonator as Primary Transducer of Liquid Hydrocarbons Moisture. Applicability. Potentials. Prospects
The article deals with the problems of measuring water content of liquid hydrocarbons by radio-technical methods. The reason for the choice of microwave methods has been justified. It is shown that the resonator method of measurement is the most acceptable. A comparative capacity assessment of the metal and dielectric cavity resonators has been made. The author gives reasons for the feasibility of using the open dielectric resonator (DR) as a primary transducer of oil-products moisture. It is estimated that such decision allows online measurements directly in the pumped oil flow. The advantages and disadvantages of the proposed solution are discussed.
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 325-327
Dielectric Resonator as Primary Transducer of Liquid Hydrocarbons Moisture. Applicability. Potentials. Prospects
The article deals with the problems of measuring water content of liquid hydrocarbons by radio-technical methods. The reason for the choice of microwave methods has been justified. It is shown that the resonator method of measurement is the most acceptable. A comparative capacity assessment of the metal and dielectric cavity resonators has been made. The author gives reasons for the feasibility of using the open dielectric resonator (DR) as a primary transducer of oil-products moisture. It is estimated that such decision allows online measurements directly in the pumped oil flow. The advantages and disadvantages of the proposed solution are discussed.
- 1 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Reference Generator with Load-Dissipated Power Control System
This paper considers a method of automatic control of the load-dissipated power of a reference generator. The power controller is based on discrete logic elements. The required power is set by changing the voltage level of a signal generator by means of a software-controlled attenuator according to the control function law, depending on the state and properties of the research object. The paper describes the principle of self-correction of the main parameters of a reference generator, which ensures a constant power and energy of impact on the research object. The main source of errors and the method to reduce them are determined. The paper also presents experimental studies of the developed device.
- 1 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Reference Generator with Load-Dissipated Power Control System
This paper considers a method of automatic control of the load-dissipated power of a reference generator. The power controller is based on discrete logic elements. The required power is set by changing the voltage level of a signal generator by means of a software-controlled attenuator according to the control function law, depending on the state and properties of the research object. The paper describes the principle of self-correction of the main parameters of a reference generator, which ensures a constant power and energy of impact on the research object. The main source of errors and the method to reduce them are determined. The paper also presents experimental studies of the developed device.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Automation of Project Publishing Process in Corporate Information System
The development of intelligent production creates a stable and constantly growing need for equipment, software, design solutions, various technical and technological services. The specificity of products and services that are in demand in promising markets in the field of smart production requires the availability of various types of information systems for monitoring and management at all stages of production. In particular, corporate information analytical systems can be classified as such systems. The process of deploying an information system on a remote server can involve building and linking several dependent or independent components. The time and effort required to manually manage the deployment of the information system are unreasonably large. It is proposed to automate this process in order to reduce the impact of human errors and time. The analysis of modern means of increasing the speed of deployment of corporate systems is carried out. The architecture of a new solution for the continuous deployment of the system has been developed.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Automation of Project Publishing Process in Corporate Information System
The development of intelligent production creates a stable and constantly growing need for equipment, software, design solutions, various technical and technological services. The specificity of products and services that are in demand in promising markets in the field of smart production requires the availability of various types of information systems for monitoring and management at all stages of production. In particular, corporate information analytical systems can be classified as such systems. The process of deploying an information system on a remote server can involve building and linking several dependent or independent components. The time and effort required to manually manage the deployment of the information system are unreasonably large. It is proposed to automate this process in order to reduce the impact of human errors and time. The analysis of modern means of increasing the speed of deployment of corporate systems is carried out. The architecture of a new solution for the continuous deployment of the system has been developed.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Information Security Ensuring in Industrial Networks on Digital Substations
The paper contains the solution of problems of security and information protection in industrial networks on digital substations. The subject is due to the high rate of a development of smart grids. The study includes an analysis of the current state of the issue of information security ensuring of the software and hardware complex of a digital substation in accordance with the existing standards and methods. A feature of industrial networks under consideration is the introduction of combined digital current and voltage instrument transformers of a new type in high-voltage electrical substations. The work was performed to determine the functional requirements for hardware and software for new intelligent electronic devices for digital substations in order to further secure the technical protection of information.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Information Security Ensuring in Industrial Networks on Digital Substations
The paper contains the solution of problems of security and information protection in industrial networks on digital substations. The subject is due to the high rate of a development of smart grids. The study includes an analysis of the current state of the issue of information security ensuring of the software and hardware complex of a digital substation in accordance with the existing standards and methods. A feature of industrial networks under consideration is the introduction of combined digital current and voltage instrument transformers of a new type in high-voltage electrical substations. The work was performed to determine the functional requirements for hardware and software for new intelligent electronic devices for digital substations in order to further secure the technical protection of information.